To avoid changes to input bindings not reaching linux-input reviewers
add an appropriate file pattern to the MAINTAINERS entry.
Reported-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree support for the I2C and SPI variant of AD7879(-1).
This allows to specify the touchscreen controller as a I2C client
node or SPI slave device. Most of the options available in platform
data are also available as device tree properties, the only exception
being GPIO capabilities, which can not be activated through device
tree currently.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The X/Y position measurements read from the controller are interpreted
wrong. The first measurement X+ contains the Y position, and the second
measurement Y+ the X position (see also Table 11 Register Table in the
data sheet).

The problem is already known and a swap option has been introduced:
commit 6680884a ("Input: ad7879 - add option to correct xy axis")

However, the meaning of the new boolean is inverted since the underlying
values are already swapped. Let ts->swap_xy set to true actually be the
swapped configuration of the two axis.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The header file is used by the SPI and I2C variant of the driver.
Therefore, move it to a more generic place under platform_data.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Technologic Systems TS-4800 is an i.MX515 board, so its drivers
are useless unless building a SOC_IMX51 kernel, except for build
testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Bring in updates to roraty encoder driver switching it away from legacy
platform data and over to generic device properties and adding support
for encoders using more than 2 GPIOs.

When changing the scan rate as part of runtime-resume process we may lose
some of the events, because:

1) for gen3 trackpads, the driver must msleep() some time to ensure that
the device is ready to accept next command;

2) for gen5 and later trackpads, the queue dumping function will simply
ignore the events when waiting for the set power mode command response.

The solution is to keep polling and report those valid events when the set
power mode command is in progress.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A dependency on ARCH_SHMOBILE seems to be the best option for sh_keysc:

* For Super H based SoCs: sh_keysc is used on SH_MIGOR, SH_ECOVEC, SH_KFR2R09,
  SH_7722_SOLUTION_ENGINE, and SH_7724_SOLUTION_ENGINE, which depend on
  either CPU_SUBTYPE_SH7722 or CPU_SUBTYPE_SH7724, and both select
  ARCH_SHMOBILE.

* For ARM Based SoCs: Since the removal of legacy (non-multiplatform) support
  this driver has not been used by any Renesas ARM based SoCs. The Renesas
  ARM based SoCs currently select ARCH_SHMOBILE, however, it is planned
  that this will no longer be the case.

This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for retrieving device resolution (pixels per mm) from firmware
and using it when setting up input device.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This changes how the used gpios are stored (i.e. a struct gpio_descs
instead of two struct gpio_desc) and as with >2 gpios the states are
numbered differently the function rotary_encoder_get_state returns
unencoded numbers instead of grey encoded numbers before. The latter has
some implications on how the returned value is used and so the change is
bigger than one might expect at first.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Drop support for platform data passed via a C-structure and switch to
device properties instead, which should make the driver compatible with all
platforms: OF, ACPI and static boards. Static boards should use property
sets to communicate device parameters to the driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

commit e4b88e19
"Input: stmpe-ts - enforce device tree only mode"
removed platform data but accidentally stripped away useful
kerneldoc, so reintroduce it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The SNVS power key driver has suspend/resume functions that
are accessed using SIMPLE_DEV_PM_OPS, which hide the reference
when CONFIG_PM_SLEEP is not set, resulting in a warning about
unused functions:

drivers/input/keyboard/snvs_pwrkey.c:183:12: error: 'imx_snvs_pwrkey_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/snvs_pwrkey.c:194:12: error: 'imx_snvs_pwrkey_resume' defined but not used [-Werror=unused-function]

This adds __maybe_unused annotations to let the compiler know
it can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The spear keyboard driver uses #ifdef CONFIG_PM to hide its
power management functions, but then uses references from
SIMPLE_DEV_PM_OPS that are only present if both CONFIG_PM
and CONFIG_PM_SLEEP are set, resulting in a warning about unused
functions:

drivers/input/keyboard/spear-keyboard.c:292:12: error: 'spear_kbd_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/spear-keyboard.c:345:12: error: 'spear_kbd_resume' defined but not used [-Werror=unused-function]

This removes the #ifdef and instead uses a __maybe_unused
annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add ACPI binding to the goldfish events driver.
Signed-off-by: Jason Hu <jia-cheng.hu@intel.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree bindings to the Goldfish virtual platform event driver.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of manipulating capability bits directly let's use appropriate
helpers. Also there is no need to explicitly set EV_ABS when calling
input_set_abs_params().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of using old GPIO API, let's switch to GPIOD API, which
automatically handles polarity.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of guarding PM methods with #ifdef let's mark them as
__maybe_unused as it allows for better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert to use threaded IRQs to support GPIOs that can sleep.
Protect the irq handler with mutex as it can be triggered from
two different irq lines accessing the same state.

This allows using GPIO expanders behind I2C or SPI bus.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This is an input driver for MELFAS MIP4 Touchscreen devices, such as
MMS400, MMS500, MCS8000, MIT200, MIT300, MIT400, MFS10. All devices
implementing MIP4 protocol (MELFAS Interface Protocol Version 4) should
be supported by this driver.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

If COMPILE_TEST is enabled, relax the dependency on GPIOLIB for the
recently introduced or relaxed symbols TOUCHSCREEN_GOODIX and
TOUCHSCREEN_COLIBRI_VF50.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Driver for the BYD BTP10463 touchpad, found in PC Specialist `Lafite'
laptops. This patch sends the magic command sequence which causes the
touchpad to stream intellimouse-style packets.

Gestures are detected inside the touchpad, and exposed as special
values in the Z component of each packet - absolute coordinates are
not supported, even in the Windows driver. At present, this supports
two-finger vertical and horizontal scrolling, and provides the
framework to expose the other gestures it can recognize.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since we removed support for calling an init() callback from
the platform data, introduce a function which initializes
the chip by performing a hard reset, using the reset gpio
defined in the device properties.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Drop support for platform data passed via a C-structure and switch to
device properties instead, which should make the driver compatible
with all platforms: OF, ACPI and static boards. Static boards should
use property sets to communicate device parameters to the driver.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use devm_() functions for allocating memory, input device and IRQ.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use managed resource API for simplifying error paths.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support to disable buttons from DT via status property if given button
is not supported on given platforms. This will help re-using existing dtsi
files across multiple platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Allow specifying name if input device via device tree property. This helps
userspace code to get name and perform proper event to key mapping in some
cases (for example, on Android).
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Bring in update to xpad driver improves support of Xbox One and wireless
controllers and fixes handling of concurrent requests to force feedback
and LEDs.

Apparently the Covert Forces ID is not Covert Forces pad exclusive, but
rather denotes a new firmware version that can be found on all new
controllers and can be also updated on old hardware using Windows 10.

see: https://github.com/paroj/xpad/issues/19Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Both T100 and T9 handle range and orientation in a similar fashion.
Reduce duplication between the two implementations.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.

Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.

Commit 3c0213d1 ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.

Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

As of e0361b70 ("Input: wacom_w8001 - split the touch and pen devices
into two devices") the touch events aren't multiplexed over the same device
anymore, the use of ABS_MT_TOOL_TYPE is superfluous. And even before then
it only ever sent MT_TOOL_TYPE_FINGER anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 4ea14a53 ("Input: gpio-keys - report
error when disabling unsupported key") tried let user know that they
attempted to disable an unsupported key, unfortunately the check is wrong
as it believes that all codes are invalid. Fix it by ensuring that keys
that we try to disable are subset of keys (or switches) that device
reports.

Fixes: 4ea14a53 ("Input: gpio-keys - report error when disabling unsupported key")
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull SCSI fix from James Bottomley:
 "A single fix for machines with pages > 4k (PPC mostly).

  There's a bug in our optimal transfer size code where we don't account
  for pages > 4k and can set the transfer size to be less than the page
  size causing nasty failures"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  sd: Reject optimal transfer length smaller than page size

Pull PCI fixlet from Bjorn Helgaas:
 "This marks the TI DRA7xx host bridge driver as broken.  Apparently it
  has never worked without some additional out-of-tree code, so I'm
  going to mark it broken now and remove it completely next cycle unless
  it's fixed"

* tag 'pci-v4.4-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: dra7xx: Mark driver as broken

kernel test robot has reported the following crash:

  BUG: unable to handle kernel NULL pointer dereference at 00000100
  IP: [<c1074df6>] __queue_work+0x26/0x390
  *pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53
  Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP
  CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe5 #1
  Workqueue: events vmstat_shepherd
  task: cb684600 ti: cb7ba000 task.ti: cb7ba000
  EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0
  EIP is at __queue_work+0x26/0x390
  EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000
  ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38
   DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
  CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0
  Stack:
  Call Trace:
    __queue_delayed_work+0xa1/0x160
    queue_delayed_work_on+0x36/0x60
    vmstat_shepherd+0xad/0xf0
    process_one_work+0x1aa/0x4c0
    worker_thread+0x41/0x440
    kthread+0xb0/0xd0
    ret_from_kernel_thread+0x21/0x40

The reason is that start_shepherd_timer schedules the shepherd work item
which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates
that workqueue so if the further initialization takes more than HZ we
might end up scheduling on a NULL vmstat_wq.  This is really unlikely
but not impossible.

Fixes: 373ccbe5 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress")
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>