Skip to content

L
linux
Switch branch/tag
  1. 24 Jan, 2022 13 commits
    • Marc Kleine-Budde's avatar
      can: tcan4x5x: regmap: fix max register value · e59986de
      Marc Kleine-Budde authored 
      The MRAM of the tcan4x5x has a size of 2K and starts at 0x8000. There
are no further registers in the tcan4x5x making 0x87fc the biggest
addressable register.

This patch fixes the max register value of the regmap config from
0x8ffc to 0x87fc.

Fixes: 6e1caaf8 ("can: tcan4x5x: fix max register value")
Link: https://lore.kernel.org/all/20220119064011.2943292-1-mkl@pengutronix.deSigned-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      e59986de
    • Marc Kleine-Budde's avatar
      can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if length is 0 · db72589c
      Marc Kleine-Budde authored 
      In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch

| e3938177 ("can: m_can: Disable IRQs on FIFO bus errors")

bulk read/write support has been added to the m_can_fifo_{read,write}
functions.

That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:

| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22

This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.

Fixes: e3938177 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: default avatarMichael Anochin <anochin@photo-meter.com>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      db72589c
    • Marc Kleine-Budde's avatar
      dt-bindings: can: tcan4x5x: fix mram-cfg RX FIFO config · 17a30422
      Marc Kleine-Budde authored 
      This tcan4x5x only comes with 2K of MRAM, a RX FIFO with a dept of 32
doesn't fit into the MRAM. Use a depth of 16 instead.

Fixes: 4edd396a ("dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver")
Link: https://lore.kernel.org/all/20220119062951.2939851-1-mkl@pengutronix.deSigned-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      17a30422
    • Marc Kleine-Budde's avatar
      mailmap: update email address of Brian Silverman · 984d1eff
      Marc Kleine-Budde authored 
      Brian Silverman's address at bluerivertech.com is not valid anymore,
use Brian's private email address instead.

Link: https://lore.kernel.org/all/20220110082359.2019735-1-mkl@pengutronix.de
Cc: Brian Silverman <bsilver16384@gmail.com>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      984d1eff
    • Wen Gu's avatar
      net/smc: Transitional solution for clcsock race issue · c0bf3d8a
      Wen Gu authored 
      We encountered a crash in smc_setsockopt() and it is caused by
accessing smc->clcsock after clcsock was released.

 BUG: kernel NULL pointer dereference, address: 0000000000000020
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 0 P4D 0
 Oops: 0000 [#1] PREEMPT SMP PTI
 CPU: 1 PID: 50309 Comm: nginx Kdump: loaded Tainted: G E     5.16.0-rc4+ #53
 RIP: 0010:smc_setsockopt+0x59/0x280 [smc]
 Call Trace:
  <TASK>
  __sys_setsockopt+0xfc/0x190
  __x64_sys_setsockopt+0x20/0x30
  do_syscall_64+0x34/0x90
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7f16ba83918e
  </TASK>

This patch tries to fix it by holding clcsock_release_lock and
checking whether clcsock has already been released before access.

In case that a crash of the same reason happens in smc_getsockopt()
or smc_switch_to_fallback(), this patch also checkes smc->clcsock
in them too. And the caller of smc_switch_to_fallback() will identify
whether fallback succeeds according to the return value.

Fixes: fd57770d ("net/smc: wait for pending work before clcsock release_sock")
Link: https://lore.kernel.org/lkml/5dd7ffd1-28e2-24cc-9442-1defec27375e@linux.ibm.com/T/Signed-off-by: default avatarWen Gu <guwen@linux.alibaba.com>
Acked-by: default avatarKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c0bf3d8a
    • Sukadev Bhattiprolu's avatar
      ibmvnic: remove unused ->wait_capability · 3a5d9db7
      Sukadev Bhattiprolu authored 
      With previous bug fix, ->wait_capability flag is no longer needed and can
be removed.

Fixes: 249168ad ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: default avatarSukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: default avatarDany Madden <drt@linux.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3a5d9db7
    • Sukadev Bhattiprolu's avatar
      ibmvnic: don't spin in tasklet · 48079e7f
      Sukadev Bhattiprolu authored 
      ibmvnic_tasklet() continuously spins waiting for responses to all
capability requests. It does this to avoid encountering an error
during initialization of the vnic. However if there is a bug in the
VIOS and we do not receive a response to one or more queries the
tasklet ends up spinning continuously leading to hard lock ups.

If we fail to receive a message from the VIOS it is reasonable to
timeout the login attempt rather than spin indefinitely in the tasklet.

Fixes: 249168ad ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: default avatarSukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: default avatarDany Madden <drt@linux.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      48079e7f
    • Sukadev Bhattiprolu's avatar
      ibmvnic: init ->running_cap_crqs early · 151b6a5c
      Sukadev Bhattiprolu authored 
      We use ->running_cap_crqs to determine when the ibmvnic_tasklet() should
send out the next protocol message type. i.e when we get back responses
to all our QUERY_CAPABILITY CRQs we send out REQUEST_CAPABILITY crqs.
Similiary, when we get responses to all the REQUEST_CAPABILITY crqs, we
send out the QUERY_IP_OFFLOAD CRQ.

We currently increment ->running_cap_crqs as we send out each CRQ and
have the ibmvnic_tasklet() send out the next message type, when this
running_cap_crqs count drops to 0.

This assumes that all the CRQs of the current type were sent out before
the count drops to 0. However it is possible that we send out say 6 CRQs,
get preempted and receive all the 6 responses before we send out the
remaining CRQs. This can result in ->running_cap_crqs count dropping to
zero before all messages of the current type were sent and we end up
sending the next protocol message too early.

Instead initialize the ->running_cap_crqs upfront so the tasklet will
only send the next protocol message after all responses are received.

Use the cap_reqs local variable to also detect any discrepancy (either
now or in future) in the number of capability requests we actually send.

Currently only send_query_cap() is affected by this behavior (of sending
next message early) since it is called from the worker thread (during
reset) and from application thread (during ->ndo_open()) and they can be
preempted. send_request_cap() is only called from the tasklet  which
processes CRQ responses sequentially, is not be affected.  But to
maintain the existing symmtery with send_query_capability() we update
send_request_capability() also.

Fixes: 249168ad ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: default avatarSukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: default avatarDany Madden <drt@linux.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      151b6a5c
    • Sukadev Bhattiprolu's avatar
      ibmvnic: Allow extra failures before disabling · db9f0e8b
      Sukadev Bhattiprolu authored 
      If auto-priority-failover (APF) is enabled and there are at least two
backing devices of different priorities, some resets like fail-over,
change-param etc can cause at least two back to back failovers. (Failover
from high priority backing device to lower priority one and then back
to the higher priority one if that is still functional).

Depending on the timimg of the two failovers it is possible to trigger
a "hard" reset and for the hard reset to fail due to failovers. When this
occurs, the driver assumes that the network is unstable and disables the
VNIC for a 60-second "settling time". This in turn can cause the ethtool
command to fail with "No such device" while the vnic automatically recovers
a little while later.

Given that it's possible to have two back to back failures, allow for extra
failures before disabling the vnic for the settling time.

Fixes: f15fde9d ("ibmvnic: delay next reset if hard reset fails")
Signed-off-by: default avatarSukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: default avatarDany Madden <drt@linux.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      db9f0e8b
    • Jakub Kicinski's avatar
      ipv4: fix ip option filtering for locally generated fragments · 27a8caa5
      Jakub Kicinski authored 
      During IP fragmentation we sanitize IP options. This means overwriting
options which should not be copied with NOPs. Only the first fragment
has the original, full options.

ip_fraglist_prepare() copies the IP header and options from previous
fragment to the next one. Commit 19c3401a ("net: ipv4: place control
buffer handling away from fragmentation iterators") moved sanitizing
options before ip_fraglist_prepare() which means options are sanitized
and then overwritten again with the old values.

Fixing this is not enough, however, nor did the sanitization work
prior to aforementioned commit.

ip_options_fragment() (which does the sanitization) uses ipcb->opt.optlen
for the length of the options. ipcb->opt of fragments is not populated
(it's 0), only the head skb has the state properly built. So even when
called at the right time ip_options_fragment() does nothing. This seems
to date back all the way to v2.5.44 when the fast path for pre-fragmented
skbs had been introduced. Prior to that ip_options_build() would have been
called for every fragment (in fact ever since v2.5.44 the fragmentation
handing in ip_options_build() has been dead code, I'll clean it up in
-next).

In the original patch (see Link) caixf mentions fixing the handling
for fragments other than the second one, but I'm not sure how _any_
fragment could have had their options sanitized with the code
as it stood.

Tested with python (MTU on lo lowered to 1000 to force fragmentation):

  import socket
  s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
  s.setsockopt(socket.IPPROTO_IP, socket.IP_OPTIONS,
               bytearray([7,4,5,192, 20|0x80,4,1,0]))
  s.sendto(b'1'*2000, ('127.0.0.1', 1234))

Before:

IP (tos 0x0, ttl 64, id 1053, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost.36500 > localhost.search-agent: UDP, length 2000
IP (tos 0x0, ttl 64, id 1053, offset 968, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost > localhost: udp
IP (tos 0x0, ttl 64, id 1053, offset 1936, flags [none], proto UDP (17), length 100, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost > localhost: udp

After:

IP (tos 0x0, ttl 96, id 42549, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
    localhost.51607 > localhost.search-agent: UDP, bad length 2000 > 960
IP (tos 0x0, ttl 96, id 42549, offset 968, flags [+], proto UDP (17), length 996, options (NOP,NOP,NOP,NOP,RA value 256))
    localhost > localhost: udp
IP (tos 0x0, ttl 96, id 42549, offset 1936, flags [none], proto UDP (17), length 100, options (NOP,NOP,NOP,NOP,RA value 256))
    localhost > localhost: udp

RA (20 | 0x80) is now copied as expected, RR (7) is "NOPed out".

Link: https://lore.kernel.org/netdev/20220107080559.122713-1-ooppublic@163.com/
Fixes: 19c3401a ("net: ipv4: place control buffer handling away from fragmentation iterators")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: default avatarcaixf <ooppublic@163.com>
Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      27a8caa5
    • Jianguo Wu's avatar
      net-procfs: show net devices bound packet types · 1d10f8a1
      Jianguo Wu authored 
      After commit:7866a621 ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.

Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:

Before:
  [root@localhost ~]# cat /proc/net/ptype
  Type Device      Function
  0800          ip_rcv
  0806          arp_rcv
  86dd          ipv6_rcv

After:
  [root@localhost ~]# cat /proc/net/ptype
  Type Device      Function
  ALL  ens192   tpacket_rcv
  0800          ip_rcv
  0806          arp_rcv
  86dd          ipv6_rcv

v1 -> v2:
  - fix the regression rather than adding new /proc API as
    suggested by Stephen Hemminger.

Fixes: 7866a621 ("dev: add per net_device packet type chains")
Signed-off-by: default avatarJianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1d10f8a1
    • Hangbin Liu's avatar
      bonding: use rcu_dereference_rtnl when get bonding active slave · aa603467
      Hangbin Liu authored 
      bond_option_active_slave_get_rcu() should not be used in rtnl_mutex as it
use rcu_dereference(). Replace to rcu_dereference_rtnl() so we also can use
this function in rtnl protected context.

With this update, we can rmeove the rcu_read_lock/unlock in
bonding .ndo_eth_ioctl and .get_ts_info.
Reported-by: default avatarVladimir Oltean <vladimir.oltean@nxp.com>
Fixes: 94dd016a ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: default avatarHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      aa603467
    • Marek Behún's avatar
      net: sfp: ignore disabled SFP node · 2148927e
      Marek Behún authored 
      Commit ce0aa27f ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).

We need to ignore disabled SFP bus node.

Fixes: ce0aa27f ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: default avatarMarek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2148927e
  3. 22 Jan, 2022 3 commits
  5. 21 Jan, 2022 21 commits
  7. 20 Jan, 2022 3 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7