- 24 Jun, 2017 28 commits
-
-
Rask Ingemann Lambertsen authored
commit c0369698 upstream. commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot") was intended to fix the case where a board uses an AXP806 in slave mode, but the boot loader leaves it in master mode for lack of AXP806 support. But now the driver breaks on boards where the PMIC is operating in master mode. This patch lets the driver use the new device tree property "xpowers,master-mode" to set the correct operating mode for the board. Fixes: 8824ee85 ("mfd: axp20x: Add support for AXP806 PMIC") Signed-off-by:
Rask Ingemann Lambertsen <rask@formelder.dk> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tony Lindgren authored
commit 8b8a84c5 upstream. Commit 16fa3dc7 ("mfd: omap-usb-tll: HOST TLL platform driver") added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF bit the wrong way. The comments in the code are correct, but the inverted use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be enabled instead of disabled unlike what the comments say. Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can be only pinged few times before it stops responding. Fixes: 16fa3dc7 ("mfd: omap-usb-tll: HOST TLL platform driver") Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Laura Abbott authored
commit 861ce4a3 upstream. '__vmalloc_start_set' currently only gets set in initmem_init() when !CONFIG_NEED_MULTIPLE_NODES. This breaks detection of vmalloc address with virt_addr_valid() with CONFIG_NEED_MULTIPLE_NODES=y, causing a kernel crash: [mm/usercopy] 517e1fbe: kernel BUG at arch/x86/mm/physaddr.c:78! Set '__vmalloc_start_set' appropriately for that case as well. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Laura Abbott <labbott@redhat.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: dc16ecf7 ("x86-32: use specific __vmalloc_start_set flag in __virt_addr_valid") Link: http://lkml.kernel.org/r/1494278596-30373-1-git-send-email-labbott@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Geert Uytterhoeven authored
commit 5f76895e upstream. When changing hardware control flow for a UART with dedicated RTS/CTS pins, the new AUTORTS state is not immediately reflected in the hardware, but only when RTS is raised. However, the serial core does not call .set_mctrl() after .set_termios(), hence AUTORTS may only become effective when the port is closed, and reopened later. Note that this problem does not happen when manually using stty to change CRTSCTS, as AUTORTS will work fine on next open. To fix this, call .set_mctrl() from .set_termios() when dedicated RTS/CTS pins are present, to refresh the AUTORTS or RTS state. This is similar to what other drivers supporting AUTORTS do (e.g. omap-serial). Reported-by:
Baumann, Christoph (C.) <cbaumann@visteon.com> Fixes: 33f50ffc ("serial: sh-sci: Fix support for hardware-assisted RTS/CTS") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Geert Uytterhoeven authored
commit cfa6eb23 upstream. If a UART has dedicated RTS/CTS pins, and hardware control flow is disabled (or AUTORTS is not yet effective), changing any serial port configuration deasserts RTS, as .set_termios() calls sci_init_pins(). To fix this, consider the current (AUTO)RTS state when (re)initializing the pins. Note that for SCIFA/SCIFB, AUTORTS needs explicit configuration of the RTS# pin function, while (H)SCIF handles this automatically. Fixes: d2b9775d ("serial: sh-sci: Correct pin initialization on (H)SCIF") Fixes: e9d7a45a ("serial: sh-sci: Add pin initialization for SCIFA/SCIFB") Signed-off-by:
-
Jan Kiszka authored
commit 7cd3e9db upstream. MSI needs it as well. Should have no practical impact, though, as DMA is always available on the Quark. But given the few users of pci_alloc_irq_vectors so far, this incorrect pattern may spread otherwise. Fixes: 3f3a4695 ("serial: 8250_lpss: set PCI master only for private DMA") Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
Christophe JAILLET authored
commit be40597a upstream. UARTn_FRAME_PARITY_ODD is 0x0300 UARTn_FRAME_PARITY_EVEN is 0x0200 So if the UART is configured for EVEN parity, it would be reported as ODD. Fix it by correctly testing if the 2 bits are set. Fixes: 3afbd89c ("serial/efm32: add new driver") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Eric Anholt authored
commit ca39b449 upstream. If a CMA allocation failed, the partially constructed BO would be unreferenced through the normal path, and we might choose to put it in the BO cache. If we then reused it before it expired from the cache, the kernel would OOPS. Signed-off-by:
Eric Anholt <eric@anholt.net> Fixes: c826a6e1 ("drm/vc4: Add a BO cache.") Reviewed-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170301185602.6873-2-eric@anholt.netSigned-off-by:
-
YYS authored
commit 014580ff upstream. mtk_hdmi_setup_vendor_specific_infoframe will return before handle mtk_hdmi_hw_send_info_frame.Because hdmi_vendor_infoframe_pack returns the number of bytes packed into the binary buffer or a negative error code on failure. So correct it. Fixes: 8f83f268 ("drm/mediatek: Add HDMI support") Signed-off-by:
Nickey Yang <nickey.yang@rock-chips.com> Signed-off-by:
CK Hu <ck.hu@mediatek.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit b3dd8279 upstream. mac80211 allows to modify the SMPS state of an AP both, when it is started, and after it has been started. Such a change will trigger an action frame to all the peers that are currently connected, and will be remembered so that new peers will get notified as soon as they connect (since the SMPS setting in the beacon may not be the right one). This means that we need to remember the SMPS state currently requested as well as the SMPS state that was configured initially (and advertised in the beacon). The former is bss->req_smps and the latter is sdata->smps_mode. Initially, the AP interface could only be started with SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF always. Later, a nl80211 API was added to be able to start an AP with a different AP mode. That code forgot to update bss->req_smps and because of that, if the AP interface was started with SMPS_DYNAMIC, we had: sdata->smps_mode = SMPS_DYNAMIC bss->req_smps = SMPS_OFF That configuration made mac80211 think it needs to fire off an action frame to any new station connecting to the AP in order to let it know that the actual SMPS configuration is SMPS_OFF. Fix that by properly setting bss->req_smps in ieee80211_start_ap. Fixes: f6993174 ("mac80211: set smps_mode according to ap params") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
commit e165bc02 upstream. In the commit enabling per-CPU station statistics, I inadvertedly copy-pasted some code to update rx_packets and forgot to change it to update rx_dropped_misc. Fix that. This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953. Fixes: c9c5962b ("mac80211: enable collecting station statistics per-CPU") Reported-by:
Petru-Florin Mihancea <petrum@gmail.com> Signed-off-by:
-
Rajkumar Manoharan authored
commit 5667c86a upstream. Mesh forwarding path checks for address extension mode to fetch appropriate proxied address and MPP address. Existing condition that looks for 6 address format is not strict enough so that frames with improper values are processed and invalid entries are added into MPP table. Fix that by adding a stricter check before processing the packet. Per IEEE Std 802.11s-2011 spec. Table 7-6g1 lists address extension mode 0x3 as reserved one. And also Table Table 9-13 does not specify 0x3 as valid address field. Fixes: 9b395bc3 ("mac80211: verify that skb data is present") Signed-off-by:
Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by:
-
Johannes Berg authored
commit f1f3e9e2 upstream. When VHT IBSS support was added, the size of the extra elements wasn't considered in ieee80211_ibss_build_presp(), which makes it possible that it would overrun the allocated buffer. Fix it by allocating the necessary space. Fixes: abcff6ef ("mac80211: add VHT support for IBSS") Reported-by:
Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by:
-
Joonas Lahtinen authored
commit 4681ee21 upstream. Due to the complex dependencies between workqueues and RCU, which are not easily detected by lockdep, do not synchronize RCU during shrinking. On low-on-memory systems (mem=1G for example), the RCU sync leads to all system workqueus freezing and unrelated lockdep splats are displayed according to reports. GIT bisecting done by J. R. Okajima points to the commit where RCU syncing was extended. RCU sync gains us very little benefit in real life scenarios where the amount of memory used by object backing storage is dominant over the metadata under RCU, so drop it altogether. " Yeeeaah, if core could just, go ahead and reclaim RCU queues, that'd be great. " - Chris Wilson, 2016 (0eafec6d) v2: More information to commit message. v3: Remove "grep _rcu_" escapee from i915_gem_shrink_all (Andrea) Fixes: c053b5a5 ("drm/i915: Don't call synchronize_rcu_expedited under struct_mutex") Suggested-by:
Chris Wilson <chris@chris-wilson.co.uk> Reported-by:
J. R. Okajima <hooanon05g@gmail.com> Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by:
Hugh Dickins <hughd@google.com> Tested-by:
Andrea Arcangeli <aarcange@redhat.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: J. R. Okajima <hooanon05g@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jani Nikula <jani.nikula@intel.com> (cherry picked from commit 73cc0b9a) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1495097379-573-1-git-send-email-joonas.lahtinen@linux.intel.comSigned-off-by:
-
Ville Syrjälä authored
commit 9a775e03 upstream. Starting from commit b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+") we've already rotated the src coordinates by 270 degrees by the time we check if a scaler is needed or not, so we must not account for the rotation a second time. Previously we did these steps in the opposite order and hence the scaler check had to deal with rotation itself. The double rotation handling causes us to enable a scaler pretty much every time 90/270 degree plane rotation is requested, leading to fuzzier fonts and whatnot. v2: s/unsigned/unsigned int/ to appease checkpatch v3: s/DRM_ROTATE_0/DRM_MODE_ROTATE_0/ Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reported-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Tested-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-2-ville.syrjala@linux.intel.comReviewed-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (cherry picked from commit d96a7d2a) Signed-off-by:
-
Zhenyu Wang authored
commit c380f681 upstream. Current it's strictly checked if PVINFO version matches 1.0 for GVT-g i915 guest which doesn't help for compatibility at all and forces GVT-g host can't extend PVINFO easily with version bump for real compatibility check. This fixes that to check minimal required PVINFO version instead. v2: - drop unneeded version macro - use only major version for sanity check v3: - fix up PVInfo value with kernel type - one indent fix Reviewed-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by:
-
Mario Kleiner authored
commit bea10413 upstream. Commit d63c277d ("drm/amdgpu: Make display watermark calculations more accurate") made watermark calculations more accurate, but not for > 4k resolutions on 32-Bit architectures, as it introduced an integer overflow for those setups and resolutions. Fix this by proper u64 casting and division. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Reported-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: d63c277d ("drm/amdgpu: Make display watermark calculations more accurate") Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Fabio Estevam authored
commit 0f933328 upstream. According to the eLCDIF initialization steps listed in the MX6SX Reference Manual the eLCDIF block reset is mandatory. Without performing the eLCDIF reset the display shows garbage content when the kernel boots. In earlier tests this issue has not been observed because the bootloader was previously showing a splash screen and the bootloader display driver does properly implement the eLCDIF reset. Add the eLCDIF reset to the driver, so that it can operate correctly independently of the bootloader. Tested on a imx6sx-sdb board. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/1494007301-14535-1-git-send-email-fabio.estevam@nxp.comSigned-off-by:
-
Jason A. Donenfeld authored
commit 98c67d18 upstream. Otherwise, we enable all sorts of forgeries via timing attack. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Signed-off-by:
-
Emmanuel Grumbach authored
commit 769dc04d upstream. When a peer sends a BAR frame with PM bit clear, we should not modify its PM state as madated by the spec in 802.11-20012 10.2.1.2. Signed-off-by:
-
Paul Moore authored
commit 023f108d upstream. This patch is based on a discussion generated by an earlier patch from Tetsuo Handa: * https://marc.info/?t=149035659300001&r=1&w=2 The double free problem involves the mnt_opts field of the security_mnt_opts struct, selinux_parse_opts_str() frees the memory on error, but doesn't set the field to NULL so if the caller later attempts to call security_free_mnt_opts() we trigger the problem. In order to play it safe we change selinux_parse_opts_str() to call security_free_mnt_opts() on error instead of free'ing the memory directly. This should ensure that everything is handled correctly, regardless of what the caller may do. Fixes: e0007529 ("LSM/SELinux: Interfaces to allow FS to control mount options") Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Hans Verkuil authored
commit b94aac64 upstream. When calling CEC_RECEIVE do not check if the adapter is configured. Typically CEC_RECEIVE is called after a select() and if that indicates that there are messages in the receive queue, then you should always be able to dequeue a message. The race condition here is that a message has been received and is queued, so select() tells userspace that a message is available. But before the application calls CEC_RECEIVE the adapter is unconfigured (e.g. the HDMI cable is removed). Now select will always report that there is a message, but calling CEC_RECEIVE will always return -ENONET because the adapter is no longer configured and so will never actually dequeue the message. There is really no need for this check, and in fact the ENONET error code was never documented for CEC_RECEIVE. This may have been a left-over of old code that was never updated. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Christophe JAILLET authored
commit 5ebb6dd3 upstream. We should ensure that 'plane_no' is '< vb->num_planes' as done in 'vb2_plane_cookie' just a few lines below. Fixes: e23ccc0a ("[media] v4l: add videobuf2 Video for Linux 2 driver framework") Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Tomasz Wilczyński authored
commit b8e11f7d upstream. Commit 27ed3cd2 (cpufreq: conservative: Fix the logic in frequency decrease checking) removed the 10 point substraction when comparing the load against down_threshold but did not remove the related limit for the down_threshold value. As a result, down_threshold lower than 11 is not allowed even though values from 1 to 10 do work correctly too. The comment ("cannot be lower than 11 otherwise freq will not fall") also does not apply after removing the substraction. For this reason, allow down_threshold to take any value from 1 to 99 and fix the related comment. Fixes: 27ed3cd2 (cpufreq: conservative: Fix the logic in frequency decrease checking) Signed-off-by:
Tomasz Wilczyński <twilczynski@naver.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Arnd Bergmann authored
commit 0db47e3d upstream. While discussing the possible merits of clang warning about unused initialized functions, I found one function that was clearly meant to be called but never actually is. __ila_hash_secret_init() initializes the hash value for the ila locator, apparently this is intended to prevent hash collision attacks, but this ends up being a read-only zero constant since there is no caller. I could find no indication of why it was never called, the earliest patch submission for the module already was like this. If my interpretation is right, we certainly want to backport the patch to stable kernels as well. I considered adding it to the ila_xlat_init callback, but for best effect the random data is read as late as possible, just before it is first used. The underlying net_get_random_once() is already highly optimized to avoid overhead when called frequently. Fixes: 7f00feaf ("ila: Add generic ILA translation facility") Link: https://www.spinics.net/lists/kernel/msg2527243.htmlSigned-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Marc Kleine-Budde authored
commit 5cda3ee5 upstream. This patch adds the missing kfree() in gs_cmd_reset() to free the memory that is not used anymore after usb_control_msg(). Cc: Maximilian Schneider <max@schneidersoft.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Nicholas Bellinger authored
commit ba80aa90 upstream. This patch closes a long standing race in configfs between the creation of a new symlink in create_link(), while the symlink target's config_item is being concurrently removed via configfs_rmdir(). This can happen because the symlink target's reference is obtained by config_item_get() in create_link() before the CONFIGFS_USET_DROPPING bit set by configfs_detach_prep() during configfs_rmdir() shutdown is actually checked.. This originally manifested itself on ppc64 on v4.8.y under heavy load using ibmvscsi target ports with Novalink API: [ 7877.289863] rpadlpar_io: slot U8247.22L.212A91A-V1-C8 added [ 7879.893760] ------------[ cut here ]------------ [ 7879.893768] WARNING: CPU: 15 PID: 17585 at ./include/linux/kref.h:46 config_item_get+0x7c/0x90 [configfs] [ 7879.893811] CPU: 15 PID: 17585 Comm: targetcli Tainted: G O 4.8.17-customv2.22 #12 [ 7879.893812] task: c00000018a0d3400 task.stack: c0000001f3b40000 [ 7879.893813] NIP: d000000002c664ec LR: d000000002c60980 CTR: c000000000b70870 [ 7879.893814] REGS: c0000001f3b43810 TRAP: 0700 Tainted: G O (4.8.17-customv2.22) [ 7879.893815] MSR: 8000000000029033 <SF,EE,ME,IR,DR,RI,LE> CR: 28222242 XER: 00000000 [ 7879.893820] CFAR: d000000002c664bc SOFTE: 1 GPR00: d000000002c60980 c0000001f3b43a90 d000000002c70908 c0000000fbc06820 GPR04: c0000001ef1bd900 0000000000000004 0000000000000001 0000000000000000 GPR08: 0000000000000000 0000000000000001 d000000002c69560 d000000002c66d80 GPR12: c000000000b70870 c00000000e798700 c0000001f3b43ca0 c0000001d4949d40 GPR16: c00000014637e1c0 0000000000000000 0000000000000000 c0000000f2392940 GPR20: c0000001f3b43b98 0000000000000041 0000000000600000 0000000000000000 GPR24: fffffffffffff000 0000000000000000 d000000002c60be0 c0000001f1dac490 GPR28: 0000000000000004 0000000000000000 c0000001ef1bd900 c0000000f2392940 [ 7879.893839] NIP [d000000002c664ec] config_item_get+0x7c/0x90 [configfs] [ 7879.893841] LR [d000000002c60980] check_perm+0x80/0x2e0 [configfs] [ 7879.893842] Call Trace: [ 7879.893844] [c0000001f3b43ac0] [d000000002c60980] check_perm+0x80/0x2e0 [configfs] [ 7879.893847] [c0000001f3b43b10] [c000000000329770] do_dentry_open+0x2c0/0x460 [ 7879.893849] [c0000001f3b43b70] [c000000000344480] path_openat+0x210/0x1490 [ 7879.893851] [c0000001f3b43c80] [c00000000034708c] do_filp_open+0xfc/0x170 [ 7879.893853] [c0000001f3b43db0] [c00000000032b5bc] do_sys_open+0x1cc/0x390 [ 7879.893856] [c0000001f3b43e30] [c000000000009584] system_call+0x38/0xec [ 7879.893856] Instruction dump: [ 7879.893858] 409d0014 38210030 e8010010 7c0803a6 4e800020 3d220000 e94981e0 892a0000 [ 7879.893861] 2f890000 409effe0 39200001 992a0000 <0fe00000> 4bffffd0 60000000 60000000 [ 7879.893866] ---[ end trace 14078f0b3b5ad0aa ]--- To close this race, go ahead and obtain the symlink's target config_item reference only after the existing CONFIGFS_USET_DROPPING check succeeds. This way, if configfs_rmdir() wins create_link() will return -ENONET, and if create_link() wins configfs_rmdir() will return -EBUSY. Reported-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Tested-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Christoph Hellwig authored
commit 20223f0f upstream. Fixes: 793b80ef ("vfs: pass a flags argument to vfs_readv/vfs_writev") Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
- 17 Jun, 2017 12 commits
-
-
Greg Kroah-Hartman authored
-
Kai Chen authored
commit 4c4c5655 upstream. The decoupled MMIO feature doesn't work as intended by HW team. Enabling it with forcewake will only make debugging efforts more difficult, so let's disable it. Fixes: 85ee17eb ("drm/i915/bxt: Broxton decoupled MMIO") Cc: Zhe Wang <zhe1.wang@intel.com> Cc: Praveen Paneri <praveen.paneri@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Signed-off-by:
Kai Chen <kai.chen@intel.com> Reviewed-by:
-
Maarten Lankhorst authored
commit 4e3aed84 upstream. On some systems there can be a race condition in which no crtc state is added to the first atomic commit. This results in all crtc's having a null DDB allocation, causing a FIFO underrun on any update until the first modeset. Changes since v1: - Do not take the connection_mutex, this is already done below. Reported-by:
Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by:
Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Chris Wilson authored
commit d90c9890 upstream. Commit 7c3f86b6 ("drm/i915: Invalidate the guc ggtt TLB upon insertion") added the restoration of the invalidation routine after the GuC was disabled, but missed that the GuC was unconditionally disabled when not used. This then overwrites the invalidate routine for the older chipsets, causing havoc and breaking resume as the most obvious victim. We place the guard inside i915_ggtt_disable_guc() to be backport friendly (the bug was introduced into v4.11) but it would be preferred to be in more control over when this was guard (i.e. do not try and teardown the data structures before we have enabled them). That should be true with the reorganisation of the guc loaders. Reported-by:
Michel Thierry <michel.thierry@intel.com> (cherry picked from commit cb60606d) Signed-off-by:
-
Ville Syrjälä authored
commit 8f4d3809 upstream. The scanline counter is bonkers on VLV/CHV DSI. The scanline counter increment is not lined up with the start of vblank like it is on every other platform and output type. This causes problems for both the vblank timestamping and atomic update vblank evasion. On my FFRD8 machine at least, the scanline counter increment happens about 1/3 of a scanline ahead of the start of vblank (which is where all register latching happens still). That means we can't trust the scanline counter to tell us whether we're in vblank or not while we're on that particular line. In order to keep vblank timestamping in working condition when called from the vblank irq, we'll leave scanline_offset at one, which means that the entire line containing the start of vblank is considered to be inside the vblank. For the vblank evasion we'll need to consider that entire line to be bad, since we can't tell whether the registers already got latched or not. And we can't actually use the start of vblank interrupt to get us past that line as the interrupt would fire too soon, and then we'd up waiting for the next start of vblank instead. One way around that would using the frame start interrupt instead since that wouldn't fire until the next scanline, but that would require some bigger changes in the interrupt code. So for simplicity we'll just poll until we get past the bad line. v2: Adjust the comments a bit Cc: Jonas Aaberg <cja@gmx.net> Tested-by:
Jonas Aaberg <cja@gmx.net> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99086Signed-off-by:
Mika Kahola <mika.kahola@intel.com> Reviewed-by:
-
Ville Syrjälä authored
commit 1065467e upstream. The clipped src coordinates have already been rotated by 270 degrees for when the plane rotation is 90/270 degrees, hence the FBC code should no longer swap the width and height. Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Fixes: b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+") Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Tested-by:
-
Daniel Vetter authored
commit d38162e4 upstream. This reverts commit bc5ca47c. Gabriel put this back into generic code with commit 75f6dfe3 Author: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Date: Wed Dec 28 12:32:11 2016 -0200 drm: Deduplicate driver initialization message but somehow he missed Chris' patch to add the message meanwhile. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101025 Fixes: 75f6dfe3 ("drm: Deduplicate driver initialization message") Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Gabriel Krisman Bertazi <krisman@collabora.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170517131557.7836-1-daniel.vetter@ffwll.ch (cherry picked from commit 6bdba819) Signed-off-by:
-
Christian Borntraeger authored
commit c0e7bb38 upstream. For most cases a protection exception in the host (e.g. copy on write or dirty tracking) on the sie instruction will indicate an instruction length of 4. Turns out that there are some corner cases (e.g. runtime instrumentation) where this is not necessarily true and the ILC is unpredictable. Let's replace our 4 byte rewind_pad with 3 byte nops to prepare for all possible ILCs. Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Max Filippov authored
commit e5c86679 upstream. Linux IRQ #0 is reserved for error reporting and may not be used. Increase NR_IRQS for one additional slot and increase irq_domain_add_legacy parameter first_irq value to 1, so that linux IRQ #0 is not associated with hardware IRQ #0 in legacy IRQ domains. Introduce macro XTENSA_PIC_LINUX_IRQ for static translation of xtensa PIC hardware IRQ # to linux IRQ #. Use this macro in XTFPGA platform data definitions. This fixes inability to use hardware IRQ #0 in configurations that don't use device tree and allows for non-identity mapping between linux IRQ # and hardware IRQ #. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Dave Young authored
commit 792ef14d upstream. Maniaxx reported a kernel boot crash in the EFI code, which I emulated by using same invalid phys addr in code: BUG: unable to handle kernel paging request at ffffffffff280001 IP: efi_bgrt_init+0xfb/0x153 ... Call Trace: ? bgrt_init+0xbc/0xbc acpi_parse_bgrt+0xe/0x12 acpi_table_parse+0x89/0xb8 acpi_boot_init+0x445/0x4e2 ? acpi_parse_x2apic+0x79/0x79 ? dmi_ignore_irq0_timer_override+0x33/0x33 setup_arch+0xb63/0xc82 ? early_idt_handler_array+0x120/0x120 start_kernel+0xb7/0x443 ? early_idt_handler_array+0x120/0x120 x86_64_start_reservations+0x29/0x2b x86_64_start_kernel+0x154/0x177 secondary_startup_64+0x9f/0x9f There is also a similar bug filed in bugzilla.kernel.org: https://bugzilla.kernel.org/show_bug.cgi?id=195633 The crash is caused by this commit: 7b0a9114 efi/x86: Move the EFI BGRT init code to early init code The root cause is the firmware on those machines provides invalid BGRT image addresses. In a kernel before above commit BGRT initializes late and uses ioremap() to map the image address. Ioremap validates the address, if it is not a valid physical address ioremap() just fails and returns. However in current kernel EFI BGRT initializes early and uses early_memremap() which does not validate the image address, and kernel panic happens. According to ACPI spec the BGRT image address should fall into EFI_BOOT_SERVICES_DATA, see the section 5.2.22.4 of below document: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf Fix this issue by validating the image address in efi_bgrt_init(). If the image address does not fall into any EFI_BOOT_SERVICES_DATA areas we just bail out with a warning message. Reported-by:
Maniaxx <tripleshiftone@gmail.com> Signed-off-by:
Dave Young <dyoung@redhat.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Fixes: 7b0a9114 ("efi/x86: Move the EFI BGRT init code to early init code") Link: http://lkml.kernel.org/r/20170609084558.26766-2-ard.biesheuvel@linaro.orgSigned-off-by:
-
Richard authored
commit 22322035 upstream. The code in block/partitions/msdos.c recognizes FreeBSD, OpenBSD and NetBSD partitions and does a reasonable job picking out OpenBSD and NetBSD UFS subpartitions. But for FreeBSD the subpartitions are always "bad". Kernel: <bsd:bad subpartition - ignored Though all 3 of these BSD systems use UFS as a file system, only FreeBSD uses relative start addresses in the subpartition declarations. The following patch fixes this for FreeBSD partitions and leaves the code for OpenBSD and NetBSD intact: Signed-off-by:
Richard Narron <comet.berkeley@gmail.com> Reviewed-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Imre Deak authored
commit 6ab92afc upstream. Since commit bac2a909 Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Date: Wed Jan 21 02:17:42 2015 +0100 PCI / PM: Avoid resuming PCI devices during system suspend PCI devices will default to allowing the system suspend complete optimization where devices are not woken up during system suspend if they were already runtime suspended. This however breaks the i915/HDA drivers for two reasons: - The i915 driver has system suspend specific steps that it needs to run, that bring the device to a different state than its runtime suspended state. - The HDA driver's suspend handler requires power that it will request from the i915 driver's power domain handler. This in turn requires the i915 driver to runtime resume itself, but this won't be possible if the suspend complete optimization is in effect: in this case the i915 runtime PM is disabled and trying to get an RPM reference returns -EACCESS. Solve this by requiring the PCI/PM core to resume the device during system suspend which in effect disables the suspend complete optimization. Regardless of the above commit the optimization stayed disabled for DRM devices until commit d14d2a84 Author: Lukas Wunner <lukas@wunner.de> Date: Wed Jun 8 12:49:29 2016 +0200 drm: Remove dev_pm_ops from drm_class so this patch is in practice a fix for this commit. Another reason for the bug staying hidden for so long is that the optimization for a device is disabled if it's disabled for any of its children devices. i915 may have a backlight device as its child which doesn't support runtime PM and so doesn't allow the optimization either. So if this backlight device got registered the bug stayed hidden. Credits to Marta, Tomi and David who enabled pstore logging, that caught one instance of this issue across a suspend/ resume-to-ram and Ville who rememberd that the optimization was enabled for some devices at one point. The first WARN triggered by the problem: [ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746448] pm_runtime_get_sync() failed: -13 [ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_ numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915] [ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1 [ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017 [ 6250.746521] Workqueue: events_unbound async_run_entry_fn [ 6250.746525] Call Trace: [ 6250.746530] dump_stack+0x67/0x92 [ 6250.746536] __warn+0xc6/0xe0 [ 6250.746542] ? pci_restore_standard_config+0x40/0x40 [ 6250.746546] warn_slowpath_fmt+0x46/0x50 [ 6250.746553] ? __pm_runtime_resume+0x56/0x80 [ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746610] intel_display_power_get+0x1b/0x40 [i915] [ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915] [ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core] [ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel] [ 6250.746667] pci_pm_runtime_resume+0x76/0xa0 [ 6250.746672] __rpm_callback+0xb4/0x1f0 [ 6250.746677] ? pci_restore_standard_config+0x40/0x40 [ 6250.746682] rpm_callback+0x1f/0x80 [ 6250.746686] ? pci_restore_standard_config+0x40/0x40 [ 6250.746690] rpm_resume+0x4ba/0x740 [ 6250.746698] __pm_runtime_resume+0x49/0x80 [ 6250.746703] pci_pm_suspend+0x57/0x140 [ 6250.746709] dpm_run_callback+0x6f/0x330 [ 6250.746713] ? pci_pm_freeze+0xe0/0xe0 [ 6250.746718] __device_suspend+0xf9/0x370 [ 6250.746724] ? dpm_watchdog_set+0x60/0x60 [ 6250.746730] async_suspend+0x1a/0x90 [ 6250.746735] async_run_entry_fn+0x34/0x160 [ 6250.746741] process_one_work+0x1f2/0x6d0 [ 6250.746749] worker_thread+0x49/0x4a0 [ 6250.746755] kthread+0x107/0x140 [ 6250.746759] ? process_one_work+0x6d0/0x6d0 [ 6250.746763] ? kthread_create_on_node+0x40/0x40 [ 6250.746768] ret_from_fork+0x2e/0x40 [ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]--- v2: - Use the new pci_dev->needs_resume flag, to avoid any overhead during the ->pm_prepare hook. (Rafael) v3: - Update commit message to reference the actual regressing commit. (Lukas) v4: - Rebase on v4 of patch 1/2. Fixes: d14d2a84 ("drm: Remove dev_pm_ops from drm_class") References: https://bugs.freedesktop.org/show_bug.cgi?id=100378 References: https://bugs.freedesktop.org/show_bug.cgi?id=100770 Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Marta Lofstedt <marta.lofstedt@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Tomi Sarvela <tomi.p.sarvela@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Takashi Iwai <tiwai@suse.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: linux-pci@vger.kernel.org Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Marta Lofstedt <marta.lofstedt@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com (cherry picked from commit adfdf85d) Signed-off-by:
-
