This is a merge of a topic branch containing the support for the new
channel map API using control elements.

Some of new HP laptops have a LED for microphone (or recording) mute,
and it's controlled by GPIO pin 3.

Bind this with the capture switch to turn it on/off properly by the
mixer change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

These are 32 bit values that come from the user, we need to check for
integer overflows or we could end up allocating a smaller buffer than
expected.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Set the default value of position_fix -1, and allow user passing
position_fix=0 explicitly to set the "auto" position-fix mode.
Otherwise the auto mode may be switched to others like COMBO of
VIACOMBO when the controller prefers it, thus user can't set the auto
mode any longer.

Also updated the documentation appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A few files have been slipped from the previous commit to add MONO
channel type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Due to the definitions of CS420X_IMAC27_122 and CS420X_APPLE as
aliases, the rest enums are set to duplicated values unexpectedly.
Move the alias definitions at the end so that the enum values are
defined in the proper order.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For following the standard, define more channel map positions and
shuffle the items a bit:

- As both PulseAudio and gstreamer define MONO channel position
  explicitly, we should follow that, too.  The mono streams point to
  this channel position unless they are explicitly assigned to certain
  channel positions.

- Top-front-* and Top-rear-* positions are added, carried from
  PulseAudio's definitions.

- Move NA and MONO definitions at the top of table right after
  UNKNOWN, since these are more abstract in comparison with other
  practical positions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Provide channel maps for individual stereo streams of YMFPCI.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Provide channel maps for individual stereo streams of ENS1370 and
ENS1371.  Note that the configuration of ENS1370 uses the secondary
PCM as the front unlike ENS1371.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Provide channel maps for individual stereo streams of emu10k1x.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Provide channel maps for individual stereo streams of CA0106.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... just by defining CHIP_NAME and string concats.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

To follow the previous commit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

MacBook Pro 10,1 needs a few adjustments to make it working:
- more COEF verbs
- some pin config overrides to disable the unused pin (0x0d, 0x12),
  and fix the internal mic (0x0e)

In addition, it uses GPIO 1 and 3 like other MacBooks.

The internal digital mic on the machine is still problematic: it seems
that only the right channel is used and the left is always static.
This looks like a hardware design, so we need to cope in the software
side somehow...

The primary information and test were brought from Daniel J Blueman.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

To merge HD-audio fixes back to 3.7 development line

... to make easier to integrate into the common generic parser in near
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

snd_hda_pick_fixup() didn't check the case where the device mask bits
are set, typically used for SND_PCI_QUIRK_VENDOR() entries.  Fix this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Originally the bogus period at BDL head was introduced as a workaround
for the mismatching position update at the period boundary, typically
seen on dmix.  However, for applications like PulseAudio that don't
require period wake ups, this workaround is just superfluous.  Thus
better to disable it when no_period_wakeup is given in hw_params.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Commit c20c5a84 changed some chipsets to
default to POS_FIX_COMBO so they now use POS_FIX_LPIB instead of
POS_FIX_POSBUF. Since then I've been getting artifacts on playback, including
repeated sounds on my Asus laptop.

My hardware is Cougar Point which the commit log of
c20c5a84 mentions as tested so POS_FIX_COMBO
probably works in general but apparently it doesn't on Asus K53E therefore the
need for the quirk.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

O_RDONLY is zero so the original test (f->f_flags & O_RDONLY) is always
false and it will never do compress capture.  The test for O_WRONLY is
also slightly off.  The original test would consider "->flags =
(O_WRONLY | O_RDWR)" as write only instead of rejecting it as invalid.

I've also removed the pr_err() because that could flood dmesg.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In general, mono streams have no dedicated speaker assignment, thus
they should be rather marked as UNKNOWN position.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec.  However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.

This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
Reported-by: Daniel J Blueman <daniel@quora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The purpose of this flag is unclear. If the problem is that some machines
have broken misc/NO_PRESENCE bits, they should be fixed by pin fixups.

In addition, this causes jack detection functionality to be flawed on
the M31EI, where there are two jacks without jack detection (which is
properly marked as NO_PRESENCE), but due to ignore_misc_bit, these
jacks are instead being reported as being present but always unplugged.

BugLink: https://bugs.launchpad.net/bugs/939161Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

There is already a set of channel position definitions in alsa-lib
mixer.h, and it'd be more practical to keep the same order for the
PCM channel map, too.  The value is shifted with 1 to keep zero for
UNKNOWN.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The VOLATILE flag was added to control elements by
snd_pcm_add_chmap_ctls() just because I didn't want to have a
side-effect of "alsactl restore".  But now the set operation doesn't
allow to change the value unless the PCM stream is in PREAPRED state,
there is no reason to keep this flag.  Let's rip it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Assign the multi-channel map to front PCM, and other channel map to
each other channel PCM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Simply enable the channel map according to the h/w capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just set the channel maps depending on the hardware availability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALC650 has a channel swap option between surround and CLFE channels,
so we need to tweak the channel maps dynamically depending on the
register bit.

Now struct snd_ac97 can contain chmap pointers for playback and
capture.  The driver may store these and let ac97 driver changing the
channel mapping dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some old Nvidia HDMI codecs with 8ch support only 2/8 or
2/6/8 channels and with the fixed CLFE-first map.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... instead of the standard fixed channel maps.
The generic HDMI is based on the audio infoframe, and its configuration
can be selected via CA bits.  Thus we need a translation between the
CA index and the verbose channel map list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Although HD-audio allows pair-wise channel configurations, only the
fixed channel positions are used in this version.  In future, this can
be changed and allow user to modify the channel positions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

The SNDRV_CTL_ELEM_ACCESS_VOLATILE bit flag wasn't properly inherited
at creating control elements via snd_ctl_new1().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch implements the basic data types for the standard channel
mapping API handling.

- The definitions of the channel positions and the new TLV types are
  added in sound/asound.h and sound/tlv.h, so that they can be
  referred from user-space.

- Introduced a new helper function snd_pcm_add_chmap_ctls() to create
  control elements representing the channel maps for each PCM
  (sub)stream.

- Some standard pre-defined channel maps are provided for
  convenience.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Recently the check for non-PCM stream state was added to the generic
HDMI driver code.  But this check should be done rather to each pin
instead of each converter.  Otherwise when a different converter is
assigned at the next open, the audio infoframe can be inconsistent
with the setup using the previous converter.

For fixing this issue, this patch moves the state of the current
non-PCM status from per_cvt to per_pin.  (In addition an unused
argument cvt_nid is stripped from hdmi_setup_channel_mapping())
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The recent fix for the missing fine delayed time adjustment gives
strange error messages at each start of the playback stream, such as
  delay: estimated 0, actual 352
  delay: estimated 353, actual 705

These come from the sanity check in retire_playback_urb().  Before the
stream is activated via start_endpoints(), a few silent packets have
been already sent.  And at this point the delay account is still in
the state as if the new packets are just queued, so the driver gets
confused and spews the bogus error messages.

For fixing the issue, we just need to check whether the received
packet is valid, whether it's zero sized or not.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For multiple speaker outs, the names were previously
"Speaker,0", "Speaker,1", "Center"/"LFE", "Speaker,3". This is
inconsistent, confusing, and is not picked up correctly by PulseAudio.
Instead use "Front", "Surround", "Center"/"LFE", "Side" which
is more standard.

BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1046734Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

With the commit [2faa3bf1: ALSA: hda - Rewrite the mute-LED hook with
vmaster hook in patch_sigmatel.c], the former Master volume control
was converted to PCM.  This was supposed to be covered by the vmaster
control.  But due to the lack of "PCM" slave definition, this didn't
happen properly.  The patch fixes the missing entry.
Reported-by: Andrew Shadura <bugzilla@tut.by>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>