The new short message format is used on the new BCM57454 VFs.  Each
firmware message is a fixed 16-byte message sent using the standard
firmware communication channel.  The short message has a DMA address
pointing to the legacy long firmware message.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port net device passed to b53_fdb_copy is not used. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The helper is only used once and makes the code more complicated that it
should. Remove it and reorganize the variables so that it fits on 80
columns.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRO is not supported by Chelsio HW when rx_csum is disabled.
Update the netdev features flag when rx_csum is modified.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disable FW_OK flag while flashing Firmware. This will help to fix any
potential mailbox timeouts during Firmware flash.

Grab new devlog parameters after Firmware restart. When we FLASH new
Firmware onto an adapter, the new Firmware may have the Firmware Device Log
located at a different memory address or have a different size for it.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark carrier off before registering netdev to ensure that vlan device
picks up the correct state of the carrier
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefan Wahren says:

====================
net: qualcomm: add QCA7000 UART driver

The Qualcomm QCA7000 HomePlug GreenPHY supports two interfaces:
UART and SPI. This patch series adds the missing support for UART.

This driver based on the Qualcomm code [1], but contains some changes:
* use random MAC address per default
* use net_device_stats from device
* share frame decoding between SPI and UART driver
* improve error handling
* reimplement tty_wakeup with work queue (based on slcan)
* use new serial device bus instead of ldisc

The patches 1 - 3 are just for clean up and are not related to
the UART support. Patch 4 adds SET_NETDEV_DEV() to qca_spi.
Patches 5 - 16 prepare the existing QCA7000 code for UART support.
The last patch contains the new driver.

The code itself has been tested on a Freescale i.MX28 board and
a Raspberry Pi Zero.

Changes in v8:
  * add necessary header includes to qca_7k.c in order to reflect
    dependencies

Changes in v7:
  * fix race between tx workqueue and device deregistration (reported by Lino)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Ethernet over UART driver for the
Qualcomm QCA7000 HomePlug GreenPHY.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This merges the serdev binding for the QCA7000 UART driver (Ethernet over
UART) into the existing document.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a new DT property to define the current baud rate of the
slave device.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before we can merge the QCA7000 UART binding the document needs to be
renamed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for the QCA7000 UART binding rework the binding document.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to share common functions between QCA7000 SPI and UART protocol
driver the qca_7k_common needs to be a separate kernel module.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unfortunately the frame format is not exactly identical between SPI
and UART. In case of SPI there is an additional HW length at the
beginning. So store the initial state to make the decoding state machine
more flexible and easy to extend for UART support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As preparation for the upcoming UART driver we need a module
which contains common functions for both interfaces. The module
qca_framing is a good candidate but renaming to qca_7k_common would
make it clear.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since this driver is specific to the QCA7000, we should make the module
description more precisely.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function qcaspi_tx_cmd() is only called from qca_spi.c. So we better
move it there.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need for an additional MTU define.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to avoid mixing things up, make the MTU and frame length
defines easier to read.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to export qcaspi_netdev_open and qcaspi_netdev_close
because they are also accessible via the net_device_ops.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use SET_NETDEV_DEV() in qca_spi to create the "/sys/class/net/<if>/device"
symlink.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the BIT macro for the CONFIG and INT register values.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It doesn't make sense to use a signed variable for offset here, so
fix it up.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the includes doesn't reflect the dependencies. So
fix this up by removing all unnecessary entries and add the
necessary ones explicit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bogdan Purcareata says:

====================
net: phy: Support managed Cortina phys

So far, the Cortina family phys (CS4340 in this particular case) are only
supported in fixed link mode (via fixed_phy_register). The generic 10G
phy driver does not work well with the phylib state machine, when the phy
is registered via of_phy_connect. This prohibits the user from describing the
phy nodes in the device tree.

In order to support this scenario, and to properly describe the board
device tree, add a minimal Cortina driver that reads the status from the
right register. With the generic 10G C45 driver, the kernel will print
messages like:
[    0.226521] mdio_bus 8b96000: Error while reading PHY16 reg at 1.6
[    0.232780] mdio_bus 8b96000: Error while reading PHY16 reg at 1.5

v3 -> v4:
- Add trademark info.
- Minor documentation entry consistency nit.

v2 -> v3:
- Add documentation entry.

v1 -> v2:
- Change approach for getting the phy_id from hacking get_phy_c45_ids to
  describing the device in the device tree via ethernet-phy-id.

More patch version changes per individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree description info for Cortina 10G phy devices.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic support for Cortina PHY drivers. Support only CS4340 for now.
The phys are not compatible with IEEE 802.3 clause 22/45 registers.

Implement proper read_status support. The generic 10G phy driver causes
bus register access errors.

The driver should be described using the "ethernet-phy-id" device tree
compatible.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: DCBx and Attentions series

The series contains 2 major components [& some odd bits]:
 - The first 3 patches are DCBx-related, containg missing bits in the
   implementation, correcting existing API and removing code no longer
   necessary.
 - Most of the remaining patches are interrupt/hw-attention related,
   adding some differeneces relating to QL41xxx and QL45xxx differences.
   While at it, they also remove a large chunk of unnecessary structure
   definitions.

The series also contain a patch [#10] that was accidently missing
from a previous series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve PCI performance by adjusting padding sizes to match those of the
host machine's cacheline.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parities might exhibit a flood behavior since we re-enable the
attention line without preventing the parity from re-triggering the
assertion.
Mask the source in AEU until the parity would be handled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In strucuture reflecting the AEU hw block some entries
represent multiple HW bits, and the associated name is in fact
a pattern.
Today, whenever such an attention would be asserted the resulted
prints would show the pattern string instead of indicating which
of the possible bits was set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 4 attention bits in AEU that have different meaning
for QL45xxx and QL41xxx adapters.

Instead of doing a massive infrastructure change in favor of these
bits, we implement a point fix where only those four would change
meaning dependent on the adapter involved.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have almost all the necessary information regarding attentions
in the logic employed for taking register dumps.
Add some more and get rid of the seperate implementation we have today
for identifying & printing various attention sources.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case management firmware indicates a change in the used S-tag,
propagate the configuration to HW and FW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The QL41xxx adapters' PCI allows a single configuration for the
MSI-x table size of all child VFs of a given PF.
The existing code wouldn't cause the management firmware to set
that value, meaning the VFs would retain the default MSI-x table
size.

Introduce a new scheme so that whenever a VF is enabled, driver
would set the number of MSI-x to be the maximum over the various
VFs' needs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Older firmware used by device didn't distinguish between RoCE and RoCE
V2 from DCBx configuration perspective, and as a result we've used to
take a the RoCE-related configuration and apply to it for both.

Since we now support configuring each its own values, there's no reason
to reflect [& configure] that both are using the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using a boolean value that propagates to FW configuration,
use the proper firmware HSI values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some getters are not getting filled with the correct information
regarding local DCBx.

Fixes: 49632b58 ("qed: Add support for static dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: another round of extack handling for routing

This set focuses on passing extack through lwtunnel and MPLS with
additional catches for IPv4 route add and minor cleanups in MPLS
encountered passing the extack arg around.

v2
- mindful of bloat adding duplicate messages
  + refactored prefix and prefix length checks in ipv4's fib_table_insert
    and fib_table_del
  + refactored label check in mpls

- split mpls cleanups into 2 patches
  + move nla_get_via up in af_mpls to avoid forward declaration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>