- 12 Mar, 2020 2 commits
-
-
Brad Love authored
The ds3103b demodulator identifies as an m88rs600, but requires different clock settings and firmware, along with differences in register settings. Changes were reverse engineered using an instrumented downstream GPLv2 driver to compare i2c traffic and clocking. The mclk functions are from the downstream GPLv2 driver. Signed-off-by:
Brad Love <brad@nextdimension.cc> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Sean Young authored
There are many protocols that encode more than 32 bit. We want 64 bit support so that BPF IR decoders can decode more than 32 bit. None of the existing kernel IR decoders/encoders support 64 bit, for now. The MSC_SCAN event can only contain 32 bit scancodes, so we only generate MSC_SCAN events if the scancode fits into 32 bits. The full 64 bit scancode can be read from the lirc chardev. Signed-off-by:
-
- 05 Mar, 2020 21 commits
-
-
Maxime Jourdan authored
This adds VP9 decoding for the Amlogic GXL, G12A & SM1 SoCs, using the commong "HEVC" HW decoder. For G12A & SM1, it uses the IOMMU support from the firmware. For 10bit decoding, the firmware can only decode in the proprietary Amlogic Framebuffer Compression format, but can output in 8bit NV12 buffer while writing the decoded frame. Signed-off-by:
Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Tested-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Maxime Jourdan authored
Amlogic VP9 decoder requires an additional 16-byte payload before every frame header. The source buffer is updated in-place, then given to the Parser FIFO DMA. The FIFO DMA copies the blocks into the 16MiB parser ring buffer, then parses and copies the slice into the decoder "workspace". Signed-off-by:
-
Maxime Jourdan authored
Add support for the HEVC & VP9 common decoder support, handling Amlogic GXBB, GXL, G12A and SM1 platforms. This handles the "HEVC" hw decoder used for HEVC and VP9, and will be using in the new H264 multi-instance decoder for G12A & SM1 platforms. Signed-off-by:
-
Maxime Jourdan authored
Add helpers to support the lossless framebuffer compression format that will be used in HEVC & VP9 decoders when decoding 10bit content for downsampling to 8bit NV12 and later proper compressed buffer support. Signed-off-by:
-
Neil Armstrong authored
The HEVC/VP9 aligns the plane stride on 32, so align the planes stride for all codecs to 32 to satisfy HEVC/VP9 decoding using the "HEVC" HW. This fixes VP9 decoding of streams with following (not limited) widths: - 264 -288 - 350 - 352 - 472 - 480 - 528 - 600 - 720 - 800 - 848 - 1440 Signed-off-by:
-
Maxime Jourdan authored
Add support for the H264 compressed format (V4L2_PIX_FMT_H264). Signed-off-by:
-
Maxime Jourdan authored
Add all the necessary bits to pass v4l2-compliance in stateful decoding mode. Mostly includes tracking the state of the decoder, allowing the OUTPUT queue to stream while the CAPTURE queue is inactive, handling resolution change events, draining with V4L2_DEC_CMD_STOP, copying more metadata from the src buffers to the dst buffers, etc. Signed-off-by:
-
Neil Armstrong authored
Use the previously introduced v4l2-mem2mem core APIs to handle the drainig, stopped and next-buf-is-last states. With these changes, the v4l2-compliance still passes with the following commands : >>>><><><><><><><><><><><><><><><><>< 15.53 fps 15.53 fps ><><><><><><><><><><><><>< 13.99 fps 13.99 fps ><><><><><><><><><><><>< 13.52 fps 13.52 fps ><><><><><><><><><><><><>< 13.41 fps 13.41 fps ><><><><><><><><><><><><>< 13.21 fps 13.21 fps ><><><><><><><><><><><>< 13.09 fps 13.09 fps ><><><><><><>< STOP ENCODER <<< EOS EVENT v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits [...] Total for vicodec device /dev/video0: 50, Succeeded: 50, Failed: 0, Warnings: 0 The full output is available at [1] v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits [...] Total for vicodec device /dev/video1: 50, Succeeded: 50, Failed: 0, Warnings: 0 The full output is available at [2] No functional changes should be noticed. [1] https://termbin.com/25nn [2] https://termbin.com/dza4Suggested-by:
-
Neil Armstrong authored
Since the draining and stop phase of the HW decoder mem2mem bahaviour is now clearly defined, we can move handling of the following states to the common v4l2-mem2mem core code: - draining - stopped - next-buf-is-last By introducing the following v4l2-mem2mem APIs: - v4l2_m2m_encoder_cmd/v4l2_m2m_ioctl_encoder_cmd to handle start/stop command - v4l2_m2m_decoder_cmd/v4l2_m2m_ioctl_decoder_cmd to handle start/stop command - v4l2_m2m_update_start_streaming_state to update state on start of streaming of the de/encoder queue - v4l2_m2m_update_stop_streaming_state to update state on stop of streaming of the de/encoder queue - v4l2_m2m_last_buffer_done to make the current dest buffer as the last one And inline helpers: - v4l2_m2m_mark_stopped to mark the de/encoding process as stopped - v4l2_m2m_clear_state to clear the de/encoding state - v4l2_m2m_dst_buf_is_last to detect the current dequeued dst_buf is the last - v4l2_m2m_has_stopped to detect the de/encoding stopped state - v4l2_m2m_is_last_draining_src_buf to detect the current source buffer should be the last processing before stopping the de/encoding process The special next-buf-is-last when min_buffers != 1 case is also handled in v4l2_m2m_qbuf() by reusing the other introduced APIs. This state management has been stolen from the vicodec implementation, and is no-op for drivers not calling the v4l2_m2m_encoder_cmd or v4l2_m2m_decoder_cmd and v4l2_m2m_update_start/stop_streaming_state. The vicodec will be the first one to be converted as an example. Signed-off-by:
-
Hans Verkuil authored
When the request is completed, all controls are copied to the request object. However, when VIDIOC_G_EXT_CTRLS attempts to read control values from the request it will read the current value instead for any control reference that has a NULL ref->req pointer. But that's wrong: after completing the request *all* controls should have a non-NULL ref->req pointer since they are after all copied to the request. So set ref->req if it wasn't set already. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
-
YueHaibing authored
VIDEO_USBVISION driver depends on MEDIA_USB_SUPPORT Fixes: 8fb12ce2 ("media: usbvision: deprecate driver") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Dmitry Osipenko authored
There is a new devm_platform_ioremap_resource_byname() helper in the kernel now, which helps to make code cleaner a tad by replacing few "boilerplate" lines of code with a single line. Let's utilize that new helper in the VDE driver. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Reviewed-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Benoit Parrot authored
disable_irqs() was mistakenly disabling all interrupts when called. This cause all port stream to stop even if only stopping one of them. Cc: stable <stable@vger.kernel.org> Signed-off-by:
Benoit Parrot <bparrot@ti.com> Signed-off-by:
-
Steve Longerbeam authored
Unlike the PRPENC and PRPVF subdevices, the CSI's cannot convert quantization from sink to source, or do any kind of Y'CbCr <-> RGB encoding. So the CSI's cannot allow quantization and ycbcr_enc to be selectable by the user and must be propagated from sink to source. Fixes: 4791bd7d ("media: imx: Try colorimetry at both sink and source pads") Reported-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Steve Longerbeam <slongerbeam@gmail.com> Tested-by:
Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by:
-
Jonathan Neuschäfer authored
The new syntax is available since commit 43756e34 ("scripts/kernel-doc: Add support for named variable macro arguments"). The same HTML output is produced with and without this patch. Signed-off-by:
Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by:
-
Sergiu Cuciurean authored
In a recent change to the SPI subsystem [1], a new `delay` struct was added to replace the `delay_usecs`. This change replaces the current `delay_usecs` with `delay` for this driver. The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure that both `delay_usecs` & `delay` are used (in this order to preserve backwards compatibility). [1] commit bebcfd27 ("spi: introduce `delay` field for `spi_transfer` + spi_transfer_delay_exec()") Signed-off-by:
Sergiu Cuciurean <sergiu.cuciurean@analog.com> Signed-off-by:
-
Eugen Hristev authored
The entity variable was being initialized in the wrong place, before the parameters have been checked. To solve this, completely removed the entity variable and replaced it with the initialization value : &sd->entity. This will avoid dereferencing 'sd' pointer before it's being checked if it's NULL. Fixes: 61f5db54 ("[media] v4l: Make v4l2_subdev inherit from media_entity") Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Dafna Hirschfeld authored
sd->devnode is released after calling v4l2_subdev_release. Therefore it should be set to NULL so that the subdev won't hold a pointer to a released object. This fixes a reference after free bug in function v4l2_device_unregister_subdev Fixes: 0e43734d ("media: v4l2-subdev: add release() internal op") Cc: stable@vger.kernel.org Signed-off-by:
Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Reviewed-by:
Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by:
-
Dafna Hirschfeld authored
A use-after-free bug occures when unbinding the device while it streams. The 'struct vimc_ent_device' allocated for the 'Sensor A' is freed when calling the sensor's 'rm' callback but the freed pointer is later accessed in the function 'vimc_streamer_pipeline_terminate'. To fix this bug, move the release callback of the vimc entities and vimc_device to the release callback of v4l2_device. The .rm callback of vimc_ent_config is replaced by two callbacks: .unregister - this is called upon removing the device and it unregisters the entity. This is an optional callback since subdevices don't need to implement it because they are already unregistered in v4l2_device_unregister. .release - this is called from the release callback of v4l2_device and it frees the entity. This ensures that the entities will be released when the last fh of any of the devices is closed. The commands that cause the crash and the KASAN report: media-ctl -d platform:vimc -V '"Sensor A":0[fmt:SBGGR8_1X8/640x480]' media-ctl -d platform:vimc -V '"Debayer A":0[fmt:SBGGR8_1X8/640x480]' v4l2-ctl -z platform:vimc -d "RGB/YUV Capture" -v width=1920,height=1440 v4l2-ctl -z platform:vimc -d "Raw Capture 0" -v pixelformat=BA81 v4l2-ctl --stream-mmap --stream-count=1000 -d /dev/video2 & sleep 1 echo -n vimc.0 >/sys/bus/platform/drivers/vimc/unbind [ 188.417934] BUG: KASAN: use-after-free in vimc_streamer_pipeline_terminate+0x75/0x140 [vimc] [ 188.420182] Read of size 8 at addr ffff8881e9c26008 by task bash/185 [ 188.421800] [ 188.422223] CPU: 0 PID: 185 Comm: bash Not tainted 5.5.0-rc1+ #1 [ 188.423681] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 [ 188.425938] Call Trace: [ 188.426610] dump_stack+0x75/0xa0 [ 188.427519] ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc] [ 188.429057] print_address_description.constprop.6+0x16/0x220 [ 188.430462] ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc] [ 188.431979] ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc] [ 188.433455] __kasan_report.cold.9+0x1a/0x40 [ 188.434518] ? vimc_streamer_pipeline_terminate+0x75/0x140 [vimc] [ 188.436010] kasan_report+0xe/0x20 [ 188.436859] vimc_streamer_pipeline_terminate+0x75/0x140 [vimc] [ 188.438339] vimc_streamer_s_stream+0x8b/0x3c0 [vimc] [ 188.439576] vimc_cap_stop_streaming+0x22/0x40 [vimc] [ 188.440863] __vb2_queue_cancel+0x65/0x560 [videobuf2_common] [ 188.442391] vb2_core_queue_release+0x19/0x50 [videobuf2_common] [ 188.443974] vimc_cap_rm+0x10/0x20 [vimc] [ 188.444986] vimc_rm_subdevs+0x9e/0xe0 [vimc] [ 188.446179] vimc_remove+0x19/0x70 [vimc] [ 188.447301] platform_drv_remove+0x2f/0x50 [ 188.448468] device_release_driver_internal+0x133/0x260 [ 188.449814] unbind_store+0x121/0x150 [ 188.450726] kernfs_fop_write+0x142/0x230 [ 188.451724] ? sysfs_kf_bin_read+0x100/0x100 [ 188.452826] vfs_write+0xdc/0x230 [ 188.453760] ksys_write+0xaf/0x140 [ 188.454702] ? __ia32_sys_read+0x40/0x40 [ 188.455773] ? __do_page_fault+0x473/0x620 [ 188.456780] do_syscall_64+0x5e/0x1a0 [ 188.457711] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 188.459079] RIP: 0033:0x7f80f1f13504 [ 188.459969] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f 80 00 00 00 00 48 8d 05 f9 61 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53 [ 188.464445] RSP: 002b:00007ffd7e843b58 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 188.466276] RAX: ffffffffffffffda RBX: 0000000000000006 RCX: 00007f80f1f13504 [ 188.467999] RDX: 0000000000000006 RSI: 000055ef2eb21b10 RDI: 0000000000000001 [ 188.469708] RBP: 000055ef2eb21b10 R08: 00007f80f1fe68c0 R09: 00007f80f1e26740 [ 188.471407] R10: 000055ef2eade010 R11: 0000000000000246 R12: 00007f80f1fe5760 [ 188.473381] R13: 0000000000000006 R14: 00007f80f1fe0760 R15: 0000000000000006 [ 188.475107] [ 188.475500] Allocated by task 473: [ 188.476351] save_stack+0x19/0x80 [ 188.477201] __kasan_kmalloc.constprop.6+0xc1/0xd0 [ 188.478507] vimc_sen_add+0x36/0x309 [vimc] [ 188.479649] vimc_probe+0x1e2/0x530 [vimc] [ 188.480776] platform_drv_probe+0x46/0xa0 [ 188.481829] really_probe+0x16c/0x520 [ 188.482732] driver_probe_device+0x114/0x170 [ 188.483783] device_driver_attach+0x85/0x90 [ 188.484800] __driver_attach+0xa8/0x190 [ 188.485734] bus_for_each_dev+0xe4/0x140 [ 188.486702] bus_add_driver+0x223/0x2d0 [ 188.487715] driver_register+0xca/0x140 [ 188.488767] 0xffffffffc037003d [ 188.489635] do_one_initcall+0x86/0x28f [ 188.490702] do_init_module+0xf8/0x340 [ 188.491773] load_module+0x3766/0x3a10 [ 188.492811] __do_sys_finit_module+0x11a/0x1b0 [ 188.494059] do_syscall_64+0x5e/0x1a0 [ 188.495079] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 188.496481] [ 188.496893] Freed by task 185: [ 188.497670] save_stack+0x19/0x80 [ 188.498493] __kasan_slab_free+0x125/0x170 [ 188.499486] kfree+0x8c/0x230 [ 188.500254] v4l2_subdev_release+0x64/0x70 [videodev] [ 188.501498] v4l2_device_release_subdev_node+0x1c/0x30 [videodev] [ 188.502976] device_release+0x3c/0xd0 [ 188.503867] kobject_put+0xf4/0x240 [ 188.507802] vimc_rm_subdevs+0x9e/0xe0 [vimc] [ 188.508846] vimc_remove+0x19/0x70 [vimc] [ 188.509792] platform_drv_remove+0x2f/0x50 [ 188.510752] device_release_driver_internal+0x133/0x260 [ 188.512006] unbind_store+0x121/0x150 [ 188.512899] kernfs_fop_write+0x142/0x230 [ 188.513874] vfs_write+0xdc/0x230 [ 188.514698] ksys_write+0xaf/0x140 [ 188.515523] do_syscall_64+0x5e/0x1a0 [ 188.516543] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 188.517710] [ 188.518034] The buggy address belongs to the object at ffff8881e9c26000 [ 188.518034] which belongs to the cache kmalloc-4k of size 4096 [ 188.520528] The buggy address is located 8 bytes inside of [ 188.520528] 4096-byte region [ffff8881e9c26000, ffff8881e9c27000) [ 188.523015] The buggy address belongs to the page: [ 188.524357] page:ffffea0007a70800 refcount:1 mapcount:0 mapping:ffff8881f6402140 index:0x0 compound_mapcount: 0 [ 188.527058] raw: 0200000000010200 dead000000000100 dead000000000122 ffff8881f6402140 [ 188.528983] raw: 0000000000000000 0000000000040004 00000001ffffffff 0000000000000000 [ 188.530883] page dumped because: kasan: bad access detected [ 188.532336] [ 188.532720] Memory state around the buggy address: [ 188.533871] ffff8881e9c25f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 188.535631] ffff8881e9c25f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 188.537370] >ffff8881e9c26000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 188.538996] ^ [ 188.539812] ffff8881e9c26080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 188.541549] ffff8881e9c26100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Signed-off-by:
-
Dafna Hirschfeld authored
In future patch, the release of the device will move to the release callback of v4l2_device. Therefore the device will be released only when the last fh will be closed. Dynamic allocation will then be needed since when the device is unbounded and then bounded again, it might be that the probe callback will run before the release of the last device is finished. In that case both operations will run on the same memory concurrently and cause memory corruption. This patch also removes the pdev field of vimc_device since it is not needed anymore. Signed-off-by:
-
Dafna Hirschfeld authored
replace 'vimc->pdev.dev' with 'vimc->mdev.dev' in debug prints and in assignment to vimc_ent_device.dev. This helps to unify the debug statements. This will also eliminate the need to use the pdev field in vimc_device in future patch. Signed-off-by:
-
- 02 Mar, 2020 17 commits
-
-
Vandana BN authored
Add metadata capture/output and v4l-touch support in vivid documentation. Signed-off-by:
Vandana BN <bnvandana@gmail.com> [hverkuil-cisco@xs4all.nl: fixed some typos, made some small tweaks of the text] Signed-off-by:
-
Peter Ujfalusi authored
If the dma channel request error code is EPROBE_DEFER there is no need to print error message. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Jae Hyun Yoo authored
Video engine in AST2600 has the exactly same register set with AST2500 except VR084 register which provides more precise JPEG size read back. This commit adds support for the difference and adds 'aspeed,ast2600-video-engine' compatible OF string. Signed-off-by:
Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
Eddie James <eajames@linux.ibm.com> Signed-off-by:
-
Dafna Hirschfeld authored
VB2_USERPTR support doesn't make sense for drivers based on vb2_dma_contig, so just drop it. Otherwise, queues using vb2_dma_contig_memops causes v4l2-compliance to fail for VB2_USERPTR mode, due to buffer misalignment. Signed-off-by:
Helen Koike <helen.koike@collabora.com> [hverkuil-cisco@xs4all.nl: replaced commit log with Helen's suggestion] Signed-off-by:
-
Hans Verkuil authored
Explicitly document that the driver-specific buffer structure must start with the subsystem-specific struct (vb2_v4l2_buffer in the case of V4L2). Signed-off-by:
-
Dafna Hirschfeld authored
The item 'Fix serialization on subdev ops.' was solved, so remove it from the TODO file. Signed-off-by:
-
Hans Verkuil authored
Remove a spurious 'b' in the "contiguous chunk is too small %lu/%lu b" message. Signed-off-by:
-
Rui Wang authored
VP9 bitstream specification indicate segment data should reset to default when meet key frames, intra only frames or enable error resilience mode. So memset segmentation map buffer before every decode process is not appropriate. Reset segment data only when needed, then start decoder hardware Signed-off-by:
Rui Wang <gtk_ruiwang@mediatek.com> Signed-off-by:
-
Jernej Skrabec authored
Allwinner A64 SoC also contains deinterlace core, compatible to H3. Add compatible string for it. Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by:
-
Takashi Iwai authored
Josef reported that his old-and-good Plextor ConvertX M402U video converter spews lots of WARNINGs on the recent kernels, and it turned out that the device uses a bulk endpoint for interrupt handling just like 2250 board. For fixing it, generalize the check with the proper verification of the endpoint instead of hard-coded board type check. Fixes: 7e5219d1 ("[media] go7007: Fix 2250 urb type") Reported-and-tested-by:
Josef Möllers <josef.moellers@suse.com> BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1162583 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206427Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jernej Skrabec authored
Allwinner A83T contains rotation core which can rotate and flip images. Add a driver for it. Signed-off-by:
-
Jernej Skrabec authored
Some Allwinner SoCs like A83T and A64 contain rotate core which can rotate and flip images. Add a binding for it. Signed-off-by:
-
Ezequiel Garcia authored
Currently, v4l2_pipeline_pm_use() prototype is: int v4l2_pipeline_pm_use(struct media_entity *entity, int use) Where the 'use' argument shall only be set to '1' for enable/power-on, or to '0' for disable/power-off. The integer return is specified as only meaningful when 'use' is set to '1'. Let's enforce this semantic by splitting the function in two: v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done for several reasons. It makes the API easier to use (or harder to misuse). It removes the constraint on the values the 'use' argument shall take. Also, it removes the need to constraint the return value, by making v4l2_pipeline_pm_put void return. And last, it's more consistent with other kernel APIs, such as the runtime pm APIs, which makes the code more symmetric. Signed-off-by:
-
Hans Verkuil authored
The driver is deprecated and scheduled for removal by the end of 2020. The reason is that this driver is for old and obsolete hardware, and it produces a continuous stream of syzbot errors due to poor code. In order to prevent removal the following actions would have to be taken: - clean up the code - convert to the vb2 framework - fix the disconnect and free-on-last-user handling (i.e., add a release callback for struct v4l2_device and rework the code to use that correctly). Signed-off-by:
-
Jonas Karlman authored
Using the field information attached to v4l2 buffers is not enough to determine the type of field referenced by a DPB entry: the decoded frame might contain the full picture (both top and bottom fields) but the reference only point to one of them. Let's add new V4L2_H264_DPB_ENTRY_FLAG_ flags to express that. [Keep only 2 flags and add some details about they mean] Signed-off-by:
Jonas Karlman <jonas@kwiboo.se> Signed-off-by:
Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by:
-
Mario Hros authored
Slave demod needs some time to wake up otherwise it may not respond to the following probe commands. This problem manifested randomly on my Astrometa DVB-T2 dongle. Signed-off-by:
Mario Hros <git@reversity.org> Signed-off-by:
-
Mohammad Rasim authored
videostrong kii pro comes with a nec rc, add the keymap to the dts Signed-off-by:
Mohammad Rasim <mohammad.rasim96@gmail.com> Reviewed-by:
-
