- 16 Dec, 2022 8 commits
-
-
Paul Cercueil authored
The DDC preamble and target address only need to be set once before reading the EDID, even if multiple segments have to be read. Signed-off-by:
Paul Cercueil <paul@crapouillou.net> Reviewed-by:
Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221214125821.12489-9-paul@crapouillou.net
-
Paul Cercueil authored
The DDC FIFO was cleared before the loop in it66121_get_edid_block(), and at the beginning of each iteration; which means that it did not have to be cleared before the loop. Signed-off-by:
-
Paul Cercueil authored
The DDC error IRQs will fire on the IT6610 every time the FIFO is empty, which is not very helpful. To resolve this, we can simply disable them, and handle DDC errors in it66121_wait_ddc_ready(). Signed-off-by:
-
Paul Cercueil authored
The function it66121_wait_ddc_ready() would previously read the status register until "true", which means it never actually polled anything and would just read the register once. Now, it will properly wait until the DDC hardware is ready or until it reported an error. The 'busy' variable was also renamed to 'error' since these bits are set on error and not when the DDC hardware is busy. Since the DDC ready function is now working properly, the msleep(20) can be removed. Signed-off-by:
-
Paul Cercueil authored
Since all AVI infoframe registers are contiguous in the address space, the AVI infoframe can be written in one go with regmap_bulk_write(). Signed-off-by:
-
Paul Cercueil authored
Use regmap_noinc_read() instead of reading the data from the DDC FIFO one byte at a time. Signed-off-by:
-
Paul Cercueil authored
Simplify the code of the driver by using devm_regulator_bulk_get_enable(), which will handle powering up the regulators, and disabling them on probe error or module removal. Signed-off-by:
-
Paul Cercueil authored
Add a new ite,it6610 compatible string to the IT66121 binding documentation, since the two chips are very similar. Signed-off-by:
-
- 15 Dec, 2022 11 commits
-
-
allen chen authored
Add driver to read data-lanes and link-frequencies from dt property to restrict output bandwidth. Signed-off-by:
allen chen <allen.chen@ite.com.tw> Signed-off-by:
Pin-yen Lin <treapking@chromium.org> Signed-off-by:
-
allen chen authored
Currently there are no "upstream" users. So, no existing users to break. Add properties to restrict dp output data-lanes and clock. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Pin-yen Lin authored
Add caching when EDID is read, and invalidate the cache until the bridge detects HPD low or sink count changes on HPD_IRQ. It takes 1.2s for IT6505 bridge to read a 3-block EDID, and skipping one EDID read would be a notable difference on user experience. Signed-off-by:
-
Robert Foss authored
This fixes PLL being unable to lock, and is derived from an equivalent downstream commit. Available LT9611 documentation does not list this register, neither does LT9611UXC (which is a different chip). This commit has been confirmed to fix HDMI output on DragonBoard 845c. Suggested-by:
Amit Pundir <amit.pundir@linaro.org> Reviewed-by:
-
Dave Stevenson authored
Post_disable was sending the D-PHY sequence to put any device into ULPS suspend mode, and then cutting power to the DSI block. The power-on reset state of the DSI block is for DSI to be in an operational state, not ULPS, so it then never sent the sequence for exiting ULPS. Any attached device that didn't have an external reset therefore remained in ULPS / standby, and didn't function. Use of ULPS isn't well specified in DRM, therefore remove entering it to avoid the above situation. Signed-off-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20221207-rpi-dsi-bridge-v1-6-8f68ee0b0adb@cerno.techSigned-off-by:
Maxime Ripard <maxime@cerno.tech>
-
Dave Stevenson authored
Remove the encoder functions, and create a bridge attached to this dumb encoder which implements the same functionality. As a bridge has state which an encoder doesn't, we need to add the state management functions as well. As there is no bridge atomic_mode_set, move the initialisation code that was in mode_set into _pre_enable. The code to actually enable and disable sending video are split from the general control into _enable and _disable. Signed-off-by:
-
Dave Stevenson authored
The atomic calls are preferred as the non-atomic ones are deprecated. In preparation for conversion to a bridge, switch to the atomic calls. Signed-off-by:
-
Dave Stevenson authored
Splitting the bridge chain fails for atomic bridges as the framework can't add the relevant state in drm_atomic_add_encoder_bridges. The chain was split because we needed to power up before calling pre_enable, but that is now done in mode_set, and will move into the framework. Signed-off-by:
-
Dave Stevenson authored
Breaking the bridge chain does not work for atomic bridges/panels and generally causes issues. We need to initialise the DSI host before the bridge pre_enables are called, so move that to encoder_mode_set in the same way that dw-mipi-dsi does. Signed-off-by:
-
Dave Stevenson authored
In preparation for converting the encoder to being a bridge, rename the variable holding the next bridge in the chain to out_bridge, so that our bridge can be called bridge. Signed-off-by:
-
Maxime Ripard authored
The command-line can be expressed using a code-block, and we were missing which architectures were available. Suggested-by:
Maíra Canal <mcanal@igalia.com> Reviewed-by:
-
- 14 Dec, 2022 4 commits
-
-
Pin-yen Lin authored
Add a pair of pm_runtime_get_if_in_use and pm_runtime_put_sync in the interrupt handler to make sure the bridge won't be powered off during the interrupt handlings. Also remove the irq_lock mutex because it's not guarding anything now. Fixes: ab28896f ("drm/bridge: it6505: Improve synchronization between extcon subsystem") Signed-off-by:
-
Otto Pflüger authored
Add documentation for the new io-supply property, which specifies the regulator for the I/O voltage supply on platforms where the panel panel power and I/O supplies are separate. Signed-off-by:
Otto Pflüger <otto.pflueger@abscue.de> Reviewed-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Noralf Trønnes <noralf@tronnes.org> Signed-off-by:
-
Otto Pflüger authored
To support platforms with a separate I/O voltage supply, set the new io_regulator property along with the regulator property of the DBI device. Read the I/O supply from a new "io-supply" device tree property. Signed-off-by:
-
Otto Pflüger authored
The MIPI DBI specification defines separate vdd (panel power) and vddi (I/O voltage) supplies. Displays that require different voltages for the different supplies do exist, so the supplies cannot be combined into one as they are now. Add a new io_regulator property to the mipi_dbi_dev struct which can be set by the panel driver along with the regulator property. Signed-off-by:
-
- 13 Dec, 2022 1 commit
-
-
Christian König authored
TTM is just wrapping core DMA functionality here, remove the mid-layer. No functional change. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221125102137.1801-7-christian.koenig@amd.com
-
- 12 Dec, 2022 15 commits
-
-
Xin Ji authored
Sometimes kernel may resume back quickly after suspend, and DRM not call .mode_set() to re-config display timing before calling .atomic_enable(), bridge driver with this patch to keep last configure timing. Signed-off-by:
Xin Ji <xji@analogixsemi.com> Acked-by:
Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Link: https://lore.kernel.org/r/20221118224540.619276-36-uwe@kleine-koenig.orgSigned-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Robert Foss authored
Merge branch 'i2c/client_device_id_helper-immutable' of https://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into drm-misc-next This branch has been applied to the I2C tree and others, and is a dependency of a large series of changes switching many drivers to use i2c_client_get_device_id.
-
Paul Cercueil authored
Use the DEFINE_RUNTIME_DEV_PM_OPS(), SYSTEM_SLEEP_PM_OPS(), RUNTIME_PM_OPS() and pm_ptr() macros to handle the runtime and suspend PM callbacks. These macros allow the suspend and resume functions to be automatically dropped by the compiler when CONFIG_PM is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Inki Dae <inki.dae@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221129191733.137897-10-paul@crapouillou.net
-
Paul Cercueil authored
Instead of defining two versions of intel_sysfs_rc6_init(), one for each value of CONFIG_PM, add a check on !IS_ENABLED(CONFIG_PM) early in the function. This will allow the compiler to automatically drop the dead code when CONFIG_PM is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221129191942.138244-13-paul@crapouillou.net
-
Paul Cercueil authored
Use the pm_ptr() macro to handle the .suspend / .resume / .reset_resume callbacks. This macro allows the suspend and resume functions to be automatically dropped by the compiler when CONFIG_PM is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. It also allows to drop the __maybe_unused tags. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221129191942.138244-11-paul@crapouillou.net
-
Paul Cercueil authored
Use the pm_sleep_ptr() macro to handle the .suspend / .resume callbacks. This macro allows the suspend and resume functions to be automatically dropped by the compiler when CONFIG_SUSPEND is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
-
Paul Cercueil authored
Use the DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to handle the .suspend/.resume callbacks. These macros allow the suspend and resume functions to be automatically dropped by the compiler when CONFIG_SUSPEND is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Jyri Sarha <jyri.sarhaı@iki.fi> Link: https://patchwork.freedesktop.org/patch/msgid/20221129191942.138244-8-paul@crapouillou.net
-
Paul Cercueil authored
Use the DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to handle the .suspend/.resume callbacks. These macros allow the suspend and resume functions to be automatically dropped by the compiler when CONFIG_SUSPEND is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
-
Paul Cercueil authored
Use the DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to handle the .suspend/.resume callbacks. These macros allow the suspend and resume functions to be automatically dropped by the compiler when CONFIG_SUSPEND is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
-
Paul Cercueil authored
Use the EXPORT_GPL_RUNTIME_DEV_PM_OPS() and pm_ptr() macros to handle the PM callbacks. These macros allow the PM functions to be automatically dropped by the compiler when CONFIG_PM is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Steven Price <steven.price@arm.com> Acked-by:
Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221129191942.138244-3-paul@crapouillou.net
-
Paul Cercueil authored
Use the EXPORT_GPL_DEV_PM_OPS() and pm_ptr() macros to handle the PM callbacks. These macros allow the PM functions to be automatically dropped by the compiler when CONFIG_PM is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Laurentiu Palcu <laurentiu.palcu@oss.nxp.com> Tested-by:
-
Paul Cercueil authored
Use the DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to handle the .suspend/.resume callbacks. These macros allow the suspend and resume functions to be automatically dropped by the compiler when CONFIG_SUSPEND is disabled, without having to use #ifdef guards. This has the advantage of always compiling these functions in, independently of any Kconfig option. Thanks to that, bugs and other regressions are subsequently easier to catch. Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Reviewed-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221129191733.137897-9-paul@crapouillou.net
-
- 09 Dec, 2022 1 commit
-
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
