Based on further tests, it seems that the QDMA shaper is not able to
perform shaping close to the MAC link rate without throughput loss.
This cannot be compensated by increasing the shaping rate, so it seems
to be an internal limit.

Fix the remaining throughput regression by detecting that condition and
limiting shaping to ports with lower link speed.

This patch intentionally ignores link speed gain from TRGMII, because
even on such links, shaping to 1000 Mbit/s incurs some throughput
degradation.

Fixes: f63959c7 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>

The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.

Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.

Fixes: de776d0d ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0db3dc73 ("[NETPOLL]: tx lock deadlock fix") narrowed
down the region under netif_tx_trylock() inside netpoll_send_skb().
(At that point in time netif_tx_trylock() would lock all queues of
the device.) Taking the tx lock was problematic because driver's
cleanup method may take the same lock. So the change made us hold
the xmit lock only around xmit, and expected the driver to take
care of locking within ->ndo_poll_controller().

Unfortunately this only works if netpoll isn't itself called with
the xmit lock already held. Netpoll code is careful and uses
trylock(). The drivers, however, may be using plain lock().
Printing while holding the xmit lock is going to result in rare
deadlocks.

Luckily we record the xmit lock owners, so we can scan all the queues,
the same way we scan NAPI owners. If any of the xmit locks is held
by the local CPU we better not attempt any polling.

It would be nice if we could narrow down the check to only the NAPIs
and the queue we're trying to use. I don't see a way to do that now.
Reported-by: Roman Gushchin <roman.gushchin@linux.dev>
Fixes: 0db3dc73 ("[NETPOLL]: tx lock deadlock fix")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot was able to trigger a panic [1] in icmp_glue_bits(), or
more exactly in skb_copy_and_csum_bits()

There is no repro yet, but I think the issue is that syzbot
manages to lower device mtu to a small value, fooling __icmp_send()

__icmp_send() must make sure there is enough room for the
packet to include at least the headers.

We might in the future refactor skb_copy_and_csum_bits() and its
callers to no longer crash when something bad happens.

[1]
kernel BUG at net/core/skbuff.c:3343 !
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 15766 Comm: syz-executor.0 Not tainted 6.3.0-rc4-syzkaller-00039-gffe78bbd #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
RIP: 0010:skb_copy_and_csum_bits+0x798/0x860 net/core/skbuff.c:3343
Code: f0 c1 c8 08 41 89 c6 e9 73 ff ff ff e8 61 48 d4 f9 e9 41 fd ff ff 48 8b 7c 24 48 e8 52 48 d4 f9 e9 c3 fc ff ff e8 c8 27 84 f9 <0f> 0b 48 89 44 24 28 e8 3c 48 d4 f9 48 8b 44 24 28 e9 9d fb ff ff
RSP: 0018:ffffc90000007620 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00000000000001e8 RCX: 0000000000000100
RDX: ffff8880276f6280 RSI: ffffffff87fdd138 RDI: 0000000000000005
RBP: 0000000000000000 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000000001e8 R11: 0000000000000001 R12: 000000000000003c
R13: 0000000000000000 R14: ffff888028244868 R15: 0000000000000b0e
FS: 00007fbc81f1c700(0000) GS:ffff88802ca00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2df43000 CR3: 00000000744db000 CR4: 0000000000150ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
icmp_glue_bits+0x7b/0x210 net/ipv4/icmp.c:353
__ip_append_data+0x1d1b/0x39f0 net/ipv4/ip_output.c:1161
ip_append_data net/ipv4/ip_output.c:1343 [inline]
ip_append_data+0x115/0x1a0 net/ipv4/ip_output.c:1322
icmp_push_reply+0xa8/0x440 net/ipv4/icmp.c:370
__icmp_send+0xb80/0x1430 net/ipv4/icmp.c:765
ipv4_send_dest_unreach net/ipv4/route.c:1239 [inline]
ipv4_link_failure+0x5a9/0x9e0 net/ipv4/route.c:1246
dst_link_failure include/net/dst.h:423 [inline]
arp_error_report+0xcb/0x1c0 net/ipv4/arp.c:296
neigh_invalidate+0x20d/0x560 net/core/neighbour.c:1079
neigh_timer_handler+0xc77/0xff0 net/core/neighbour.c:1166
call_timer_fn+0x1a0/0x580 kernel/time/timer.c:1700
expire_timers+0x29b/0x4b0 kernel/time/timer.c:1751
__run_timers kernel/time/timer.c:2022 [inline]

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+d373d60fddbdc915e666@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230330174502.1915328-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit c5b959ee.

Reverted change is required after commit 3948b059 ("net: introduce
a config option to tweak MAX_SKB_FRAGS") which does not exist
in this tree, yet. It's only present in -next trees at the time
of writing.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/20230331214444.GA1426512@dev-arch.thelio-3990X/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This adds conversion of VMCI specific error code to general -ENOMEM. It
is needed, because af_vsock.c passes error value returned from transport
to the user, which does not expect to get VMCI_ERROR_* values.

Fixes: c43170b7 ("vsock: return errors other than -ENOMEM to socket")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When playing with various compilers or their versions, some choke on
the t7xx code. For example (with gcc 13):
 In file included from ./arch/s390/include/generated/asm/rwonce.h:1,
                  from ../include/linux/compiler.h:247,
                  from ../include/linux/build_bug.h:5,
                  from ../include/linux/bits.h:22,
                  from ../drivers/net/wwan/t7xx/t7xx_state_monitor.c:17:
 In function 'preempt_count',
     inlined from 't7xx_fsm_append_event' at ../drivers/net/wwan/t7xx/t7xx_state_monitor.c:439:43:
 ../include/asm-generic/rwonce.h:44:26: error: array subscript 0 is outside array bounds of 'const volatile int[0]' [-Werror=array-bounds=]

There is no reason for any code in the kernel to be built with -Werror
by default. Note that we have generic CONFIG_WERROR. So if anyone wants
-Werror, they can enable that.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/20230330232717.1f8bf5ea@kernel.org/
Cc: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Cc: Intel Corporation <linuxwwan@intel.com>
Cc: Chiranjeevi Rapolu <chiranjeevi.rapolu@linux.intel.com>
Cc: Liu Haijun <haijun.liu@mediatek.com>
Cc: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Cc: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

The type of MAX_SKB_FRAGS has changed recently, so the debug printk
needs to be updated:

drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_create_interface':
drivers/net/ethernet/ti/netcp_core.c:2084:30: error: format '%ld' expects argument of type 'long int', but argument 3 has type 'int' [-Werror=format=]
 2084 |                 dev_err(dev, "tx-pool size too small, must be at least %ld\n",
      |                              ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fixes: 3948b059 ("net: introduce a config option to tweak MAX_SKB_FRAGS")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 65b32f80 ("uapi: move IPPROTO_L2TP to in.h") moved the
definition of IPPROTO_L2TP from a define to an enum, but since
__stringify doesn't work properly with enums, we ended up breaking the
modalias strings for the l2tp modules:

 $ modinfo l2tp_ip l2tp_ip6 | grep alias
 alias:          net-pf-2-proto-IPPROTO_L2TP
 alias:          net-pf-2-proto-2-type-IPPROTO_L2TP
 alias:          net-pf-10-proto-IPPROTO_L2TP
 alias:          net-pf-10-proto-2-type-IPPROTO_L2TP

Use the resolved number directly in MODULE_ALIAS_*() macros (as we
already do with SOCK_DGRAM) to fix the alias strings:

$ modinfo l2tp_ip l2tp_ip6 | grep alias
alias:          net-pf-2-proto-115
alias:          net-pf-2-proto-115-type-2
alias:          net-pf-10-proto-115
alias:          net-pf-10-proto-115-type-2

Moreover, fix the ordering of the parameters passed to
MODULE_ALIAS_NET_PF_PROTO_TYPE() by switching proto and type.

Fixes: 65b32f80 ("uapi: move IPPROTO_L2TP to in.h")
Link: https://lore.kernel.org/lkml/ZCQt7hmodtUaBlCP@righiandr-XPS-13-7390Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Sit Wei Hong says:

====================
Fix PHY handle no longer parsing

After the fixed link support was introduced, it is observed that PHY
no longer attach to the MAC properly. So we introduce a helper
function to determine if the MAC should expect to connect to a PHY
and proceed accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.

This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.

Fixes: c8238631 ("stmmac: intel: prepare to support 1000BASE-X phy interface setting")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.

Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.

Fixes: ab21cf92 ("net: stmmac: make mdio register skips PHY scanning for fixed-link")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.

Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot reported a bug as following:

refcount_t: addition on 0; use-after-free.
...
RIP: 0010:refcount_warn_saturate+0x17c/0x1f0 lib/refcount.c:25
...
Call Trace:
 <TASK>
 __refcount_add include/linux/refcount.h:199 [inline]
 __refcount_inc include/linux/refcount.h:250 [inline]
 refcount_inc include/linux/refcount.h:267 [inline]
 kref_get include/linux/kref.h:45 [inline]
 qrtr_node_acquire net/qrtr/af_qrtr.c:202 [inline]
 qrtr_node_lookup net/qrtr/af_qrtr.c:398 [inline]
 qrtr_send_resume_tx net/qrtr/af_qrtr.c:1003 [inline]
 qrtr_recvmsg+0x85f/0x990 net/qrtr/af_qrtr.c:1070
 sock_recvmsg_nosec net/socket.c:1017 [inline]
 sock_recvmsg+0xe2/0x160 net/socket.c:1038
 qrtr_ns_worker+0x170/0x1700 net/qrtr/ns.c:688
 process_one_work+0x991/0x15c0 kernel/workqueue.c:2390
 worker_thread+0x669/0x1090 kernel/workqueue.c:2537

It occurs in the concurrent scenario of qrtr_recvmsg() and
qrtr_endpoint_unregister() as following:

	cpu0					cpu1
qrtr_recvmsg				qrtr_endpoint_unregister
qrtr_send_resume_tx			qrtr_node_release
qrtr_node_lookup			mutex_lock(&qrtr_node_lock)
spin_lock_irqsave(&qrtr_nodes_lock, )	refcount_dec_and_test(&node->ref) [node->ref == 0]
radix_tree_lookup [node != NULL]	__qrtr_node_release
qrtr_node_acquire			spin_lock_irqsave(&qrtr_nodes_lock, )
kref_get(&node->ref) [WARNING]		...
					mutex_unlock(&qrtr_node_lock)

Use qrtr_node_lock to protect qrtr_node_lookup() implementation, this
is actually improving the protection of node reference.

Fixes: 0a7e0d0e ("net: qrtr: Migrate node lookup tree to spinlock")
Reported-by: syzbot+a7492efaa5d61b51db23@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=a7492efaa5d61b51db23Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets the skb owner in the recv and send path for virtio.

For the send path, this solves the leak caused when
virtio_transport_purge_skbs() finds skb->sk is always NULL and therefore
never matches it with the current socket. Setting the owner upon
allocation fixes this.

For the recv path, this ensures correctness of accounting and also
correct transfer of ownership in vsock_loopback (when skbs are sent from
one socket and received by another).

Fixes: 71dc9ec9 ("virtio/vsock: replace virtio_vsock_pkt with sk_buff")
Signed-off-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/all/ZCCbATwov4U+GBUv@pop-os.localdomain/Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes Berg says:

====================
Just a few fixes:

 * fix size calculation for EHT element to put into SKBs
 * remove erroneous pre-RCU calls for drivers not using sta_state calls
 * fix mesh forwarding and non-forwarding RX
 * fix mesh flow dissection
 * fix a potential NULL dereference on A-MSDU RX w/o station
 * make two variable non-static that really shouldn't be static

* tag 'wireless-2023-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
  wifi: mac80211: fix invalid drv_sta_pre_rcu_remove calls for non-uploaded sta
  wifi: mac80211: fix flow dissection for forwarded packets
  wifi: mac80211: fix mesh forwarding
  wifi: mac80211: fix receiving mesh packets in forwarding=0 networks
  wifi: mac80211: fix the size calculation of ieee80211_ie_len_eht_cap()
  wifi: mac80211: fix potential null pointer dereference
  wifi: mac80211: drop bogus static keywords in A-MSDU rx
====================

Link: https://lore.kernel.org/r/20230330203313.919164-1-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from CAN and WPAN.

  Still quite a few bugs from this release. This pull is a bit smaller
  because major subtrees went into the previous one. Or maybe people
  took spring break off?

  Current release - regressions:

   - phy: micrel: correct KSZ9131RNX EEE capabilities and advertisement

  Current release - new code bugs:

   - eth: wangxun: fix vector length of interrupt cause

   - vsock/loopback: consistently protect the packet queue with
     sk_buff_head.lock

   - virtio/vsock: fix header length on skb merging

   - wpan: ca8210: fix unsigned mac_len comparison with zero

  Previous releases - regressions:

   - eth: stmmac: don't reject VLANs when IFF_PROMISC is set

   - eth: smsc911x: avoid PHY being resumed when interface is not up

   - eth: mtk_eth_soc: fix tx throughput regression with direct 1G links

   - eth: bnx2x: use the right build_skb() helper after core rework

   - wwan: iosm: fix 7560 modem crash on use on unsupported channel

  Previous releases - always broken:

   - eth: sfc: don't overwrite offload features at NIC reset

   - eth: r8169: fix RTL8168H and RTL8107E rx crc error

   - can: j1939: prevent deadlock by moving j1939_sk_errqueue()

   - virt: vmxnet3: use GRO callback when UPT is enabled

   - virt: xen: don't do grant copy across page boundary

   - phy: dp83869: fix default value for tx-/rx-internal-delay

   - dsa: ksz8: fix multiple issues with ksz8_fdb_dump

   - eth: mvpp2: fix classification/RSS of VLAN and fragmented packets

   - eth: mtk_eth_soc: fix flow block refcounting logic

  Misc:

   - constify fwnode pointers in SFP handling"

* tag 'net-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (55 commits)
  net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow
  net: ethernet: mtk_eth_soc: fix L2 offloading with DSA untag offload
  net: ethernet: mtk_eth_soc: fix flow block refcounting logic
  net: mvneta: fix potential double-frees in mvneta_txq_sw_deinit()
  net: dsa: sync unicast and multicast addresses for VLAN filters too
  net: dsa: mv88e6xxx: Enable IGMP snooping on user ports only
  xen/netback: use same error messages for same errors
  test/vsock: new skbuff appending test
  virtio/vsock: WARN_ONCE() for invalid state of socket
  virtio/vsock: fix header length on skb merging
  bnxt_en: Add missing 200G link speed reporting
  bnxt_en: Fix typo in PCI id to device description string mapping
  bnxt_en: Fix reporting of test result in ethtool selftest
  i40e: fix registers dump after run ethtool adapter self test
  bnx2x: use the right build_skb() helper
  net: ipa: compute DMA pool size properly
  net: wwan: iosm: fixes 7560 modem crash
  net: ethernet: mtk_eth_soc: fix tx throughput regression with direct 1G links
  ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
  ice: add profile conflict check for AVF FDIR
  ...

Merge tag 'for-6.3/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix two DM core bugs in the code that handles splitting "abnormal" IO
   (discards, write same and secure erase) and issuing that IO to the
   correct underlying devices (and offsets within those devices).

* tag 'for-6.3/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix __send_duplicate_bios() to always allow for splitting IO
  dm: fix improper splitting for abnormal bios

Pull drm fixes from Daniel Vetter:
 "Two regression fixes in here, otherwise just the usual stuff:

   - i915 fixes for color mgmt, psr, lmem flush, hibernate oops, and
     more

   - amdgpu: dp mst and hibernate regression fix

   - etnaviv: revert fdinfo support (incl drm/sched revert), leak fix

   - misc ivpu fixes, nouveau backlight, drm buddy allocator 32bit
     fixes"

* tag 'drm-fixes-2023-03-30' of git://anongit.freedesktop.org/drm/drm: (27 commits)
  Revert "drm/scheduler: track GPU active time per entity"
  Revert "drm/etnaviv: export client GPU usage statistics via fdinfo"
  drm/etnaviv: fix reference leak when mmaping imported buffer
  drm/amdgpu: allow more APUs to do mode2 reset when go to S4
  drm/amd/display: Take FEC Overhead into Timeslot Calculation
  drm/amd/display: Add DSC Support for Synaptics Cascaded MST Hub
  drm: test: Fix 32-bit issue in drm_buddy_test
  drm: buddy_allocator: Fix buddy allocator init on 32-bit systems
  drm/nouveau/kms: Fix backlight registration
  drm/i915/perf: Drop wakeref on GuC RC error
  drm/i915/dpt: Treat the DPT BO as a framebuffer
  drm/i915/gem: Flush lmem contents after construction
  drm/i915/tc: Fix the ICL PHY ownership check in TC-cold state
  drm/i915: Disable DC states for all commits
  drm/i915: Workaround ICL CSC_MODE sticky arming
  drm/i915: Add a .color_post_update() hook
  drm/i915: Move CSC load back into .color_commit_arm() when PSR is enabled on skl/glk
  drm/i915: Split icl_color_commit_noarm() from skl_color_commit_noarm()
  drm/i915/pmu: Use functions common with sysfs to read actual freq
  accel/ivpu: Fix IPC buffer header status field value
  ...

Commit 7dd76d1f ("dm: improve bio splitting and associated IO
accounting") only called setup_split_accounting() from
__send_duplicate_bios() if a single bio were being issued. But the case
where duplicate bios are issued must call it too.

Otherwise the bio won't be split and resubmitted (via recursion through
block core back to DM) to submit the later portions of a bio (which may
map to an entirely different target).

For example, when discarding an entire DM striped device with the
following DM table:
 vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
 vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048

Before (broken, discards the first striped target's devices twice):
 device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
 device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872
 device-mapper: striped: target_stripe=0, bdev=7:0, start=2049 len=22528
 device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=22528

After (works as expected):
 device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
 device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872
 device-mapper: striped: target_stripe=0, bdev=7:2, start=2048 len=22528
 device-mapper: striped: target_stripe=1, bdev=7:3, start=2048 len=22528

Fixes: 7dd76d1f ("dm: improve bio splitting and associated IO accounting")
Cc: stable@vger.kernel.org
Reported-by: Orange Kao <orange@aiven.io>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>

"Abnormal" bios include discards, write zeroes and secure erase. By no
longer passing the calculated 'len' pointer, commit 7dd06a25 ("dm:
allow dm_accept_partial_bio() for dm_io without duplicate bios") took a
senseless approach to disallowing dm_accept_partial_bio() from working
for duplicate bios processed using __send_duplicate_bios().

It inadvertently and incorrectly stopped the use of 'len' when
initializing a target's io (in alloc_tio). As such the resulting tio
could address more area of a device than it should.

For example, when discarding an entire DM striped device with the
following DM table:
 vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
 vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048

Before this fix:

 device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=102400
 blkdiscard: attempt to access beyond end of device
 loop0: rw=2051, sector=2048, nr_sectors = 102400 limit=81920

 device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=102400
 blkdiscard: attempt to access beyond end of device
 loop1: rw=2051, sector=2048, nr_sectors = 102400 limit=81920

After this fix;

 device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=79872
 device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=79872

Fixes: 7dd06a25 ("dm: allow dm_accept_partial_bio() for dm_io without duplicate bios")
Cc: stable@vger.kernel.org
Reported-by: Orange Kao <orange@aiven.io>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>

The cache needs to be flushed to ensure that the hardware stops offloading
the flow immediately.

Fixes: 33fc42de ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-3-nbd@nbd.nameSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Check for skb metadata in order to detect the case where the DSA header
is not present.

Fixes: 2d7605a7 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-2-nbd@nbd.nameSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since we call flow_block_cb_decref on FLOW_BLOCK_UNBIND, we also need to
call flow_block_cb_incref for a newly allocated cb.
Also fix the accidentally inverted refcount check on unbind.

Fixes: 502e84e2 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230330120840.52079-1-nbd@nbd.nameSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Reported on the Turris forum, mvneta provokes kernel warnings in the
architecture DMA mapping code when mvneta_setup_txqs() fails to
allocate memory. This happens because when mvneta_cleanup_txqs() is
called in the mvneta_stop() path, we leave pointers in the structure
that have been freed.

Then on mvneta_open(), we call mvneta_setup_txqs(), which starts
allocating memory. On memory allocation failure, mvneta_cleanup_txqs()
will walk all the queues freeing any non-NULL pointers - which includes
pointers that were previously freed in mvneta_stop().

Fix this by setting these pointers to NULL to prevent double-freeing
of the same memory.

Fixes: 2adb719d ("net: mvneta: Implement software TSO")
Link: https://forum.turris.cz/t/random-kernel-exceptions-on-hbl-tos-7-0/18865/8Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1phUe5-00EieL-7q@rmk-PC.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If certain conditions are met, DSA can install all necessary MAC
addresses on the CPU ports as FDB entries and disable flooding towards
the CPU (we call this RX filtering).

There is one corner case where this does not work.

ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
ip link set swp0 master br0 && ip link set swp0 up
ip link add link swp0 name swp0.100 type vlan id 100
ip link set swp0.100 up && ip addr add 192.168.100.1/24 dev swp0.100

Traffic through swp0.100 is broken, because the bridge turns on VLAN
filtering in the swp0 port (causing RX packets to be classified to the
FDB database corresponding to the VID from their 802.1Q header), and
although the 8021q module does call dev_uc_add() towards the real
device, that API is VLAN-unaware, so it only contains the MAC address,
not the VID; and DSA's current implementation of ndo_set_rx_mode() is
only for VID 0 (corresponding to FDB entries which are installed in an
FDB database which is only hit when the port is VLAN-unaware).

It's interesting to understand why the bridge does not turn on
IFF_PROMISC for its swp0 bridge port, and it may appear at first glance
that this is a regression caused by the logic in commit 2796d0c6
("bridge: Automatically manage port promiscuous mode."). After all,
a bridge port needs to have IFF_PROMISC by its very nature - it needs to
receive and forward frames with a MAC DA different from the bridge
ports' MAC addresses.

While that may be true, when the bridge is VLAN-aware *and* it has a
single port, there is no real reason to enable promiscuity even if that
is an automatic port, with flooding and learning (there is nowhere for
packets to go except to the BR_FDB_LOCAL entries), and this is how the
corner case appears. Adding a second automatic interface to the bridge
would make swp0 promisc as well, and would mask the corner case.

Given the dev_uc_add() / ndo_set_rx_mode() API is what it is (it doesn't
pass a VLAN ID), the only way to address that problem is to install host
FDB entries for the cartesian product of RX filtering MAC addresses and
VLAN RX filters.

Fixes: 7569459a ("net: dsa: manage flooding on the CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329151821.745752-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.

This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.

Fixes: 54d792f2 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

- revert gpu time fdinfo support
- reference leak fix on imported buffers
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/de8e08c2599ec0e22456ae36e9757b9ff14c2124.camel@pengutronix.de

Merge tag 'amd-drm-fixes-6.3-2023-03-30' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-6.3-2023-03-30:

amdgpu:
- Hibernation regression fix
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330153859.18332-1-alexander.deucher@amd.com

Short summary of fixes pull:

 * various ivpu fixes
 * fix nouveau backlight registration
 * fix buddy allocator in 32-bit systems
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330141006.GA22908@linux-uq9g

Merge tag 'amd-drm-fixes-6.3-2023-03-29' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-6.3-2023-03-29:

amdgpu:
- Two DP MST fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329220059.7622-1-alexander.deucher@amd.com

Merge tag 'drm-intel-fixes-2023-03-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v6.3-rc5:
- Fix PMU support by reusing functions with sysfs
- Fix a number of issues related to color, PSR and arm/noarm
- Fix state check related to ICL PHY ownership check in TC-cold state
- Flush lmem contents after construction
- Fix hibernate oops related to DPT BO
- Fix perf stream error path wakeref balance
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87355m4gtm.fsf@intel.com

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes:

   - A potential deadlock fix for USB-audio, involving some change in
     PCM core side

   - A regression fix for probes of USB-audio devices with the
     vendor-specific PCM format bits

   - Two regression fixes for the old YMFPCI driver

   - A few HD-audio quirks as usual"

* tag 'sound-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek: Add quirk for Lenovo ZhaoYang CF4620Z
  ALSA: ymfpci: Fix BUG_ON in probe function
  ALSA: ymfpci: Create card with device-managed snd_devm_card_new()
  ALSA: usb-audio: Fix regression on detection of Roland VS-100
  ALSA: hda/realtek: Fix support for Dell Precision 3260
  ALSA: usb-audio: Fix recursive locking at XRUN during syncing
  ALSA: hda/conexant: Partial revert of a quirk for Lenovo
  ALSA: hda/realtek: Add quirks for some Clevo laptops

Pull zonefs fixes from Damien Le Moal:

 - Make sure to always invalidate the last page of an inode straddling
   inode->i_size to avoid data inconsistencies with appended data when
   the device zone write granularity does not match the page size.

 - Do not propagate iomap -ENOBLK error to userspace and use -EBUSY
   instead.

* tag 'zonefs-6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Do not propagate iomap_dio_rw() ENOTBLK error to user space
  zonefs: Always invalidate last cached page on append write

This reverts commit df622729 as it introduces a use-after-free,
which isn't easy to fix without going back to the design drawing board.
Reported-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

This reverts commit 97804a13, as it builds on top of df622729
("drm/scheduler: track GPU active time per entity") which needs to be
reverted, as it introduces a use-after-free.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

drm_gem_prime_mmap() takes a reference on the GEM object, but before that
drm_gem_mmap_obj() already takes a reference, which will be leaked as only
one reference is dropped when the mapping is closed. Drop the extra
reference when dma_buf_mmap() succeeds.

Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>

Skip mode2 reset only for IMU enabled APUs when do S4.

This patch is to fix the regression issue
https://gitlab.freedesktop.org/drm/amd/-/issues/2483
It is generated by commit b5896266 ("drm/amdgpu: skip ASIC reset
for APUs when go to S4").

Fixes: b5896266 ("drm/amdgpu: skip ASIC reset for APUs when go to S4")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2483Tested-by: Yuan  Perry <Perry.Yuan@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x

Issue the same error message in case an illegal page boundary crossing
has been detected in both cases where this is tested.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20230329080259.14823-1-jgross@suse.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The call to invalidate_inode_pages2_range() in __iomap_dio_rw() may
fail, in which case -ENOTBLK is returned and this error code is
propagated back to user space trhough iomap_dio_rw() ->
zonefs_file_dio_write() return chain. This error code is fairly obscure
and may confuse the user. Avoid this and be consistent with the behavior
of zonefs_file_dio_append() for similar invalidate_inode_pages2_range()
errors by returning -EBUSY to user space when iomap_dio_rw() returns
-ENOTBLK.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Fixes: 8dcc1a9d ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>