This was introduced in commit ed9ecb04,
but only defined if !VIRTIO_NET_NO_LEGACY.  We should always define
it: easier for users to have conditional legacy code.
Suggested-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

In particular, the virtio header always has the u16 num_buffers field.
We define a new 'struct virtio_net_hdr_v1' for this (rather than
simply calling it 'struct virtio_net_hdr', to avoid nasty type errors
if some parts of a project define VIRTIO_NET_NO_LEGACY and some don't.

Transitional devices (which can't define VIRTIO_NET_NO_LEGACY) will
have to keep using struct virtio_net_hdr_mrg_rxbuf, which has the same
byte layout as struct virtio_net_hdr_v1.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This is from all the non-PCI parts of the spec.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The 1.0 spec clearly states that you must set the ACKNOWLEDGE and
DRIVER status bits before accessing the feature bits.  This is a
problem for the early console code, which doesn't really want to
acknowledge the device (the spec specifically excepts writing to the
console's emerg_wr from the usual ordering constrains).

Instead, we check that the *size* of the device configuration is
sufficient to hold emerg_wr: at worst (if the device doesn't support
the VIRTIO_CONSOLE_F_EMERG_WRITE feature), it will ignore the
writes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

We were activating them with the virtqueues, and that's not allowed.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Linux doesn't generate these, but it's perfectly valid according to
a close reading of the spec.  I opened virtio spec bug VIRTIO-134 to
make this clearer there, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

As a demonstration, the lguest launcher is pretty strict, trying to
catch badly behaved drivers.  Document this precisely.

A good implementation would *NOT* crash the guest when these happened!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

There are some (optional) parts we don't implement, but this quotes all
the device requirements from the spec (csd 03, but it should be the same
across all released versions).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The next patch will insert many quotes from the virtio 1.0 spec; they
make most sense if we copy the spec.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

We were clearing the lower bits when setting the upper bits.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The example launcher doesn't reset the queue_enable like the spec says
we have to.  Plus, we should reset the size in case they negotiated
a different (smaller) one.

This is easy to test by unloading and reloading a virtio module.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The general documentation we have for pv_ops is currenty present
on the IA64 docs, but since this documentation covers IA64 xen
enablement and IA64 Xen support got ripped out a while ago
through commit d52eefb4 present since v3.14-rc1 lets just
simplify, generalize and move the pv_ops documentation to a
shared place.

Cc: Isaku Yamahata <yamahata@valinux.co.jp>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: xen-devel@lists.xenproject.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Disappointing, as this was kind of neat (especially getting to use RCU
to manage the address -> eventfd mapping).  But now the devices are PCI
handled in userspace, we get rid of both the NOTIFY hypercall and
the interface to connect an eventfd.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This was only used for early console, now we can get rid of it altogether.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This involves manually checking the console device (which is always in
slot 1 of bus 0) and using the window in VIRTIO_PCI_CAP_PCI_CFG to
program it (as we can't map the BAR yet).

We could in fact do this much earlier, but we wait for the first
write from the virtio_cons_early_init() facility.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This simplifies the early probe.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The VIRTIO_PCI_CAP_PCI_CFG in the PCI virtio 1.0 spec allows access to
the BAR registers without mapping them.  This is a compulsory feature,
and we implement it here.

There are some subtleties involving access widths which we should
note:

4.1.4.7.1 Device Requirements: PCI configuration access capability

...
   Upon detecting driver write access to pci_cfg_data, the device MUST
   execute a write access at offset cap.offset at BAR selected by
   cap.bar using the first cap.length bytes from pci_cfg_data.

   Upon detecting driver read access to pci_cfg_data, the device MUST
   execute a read access of length cap.length at offset cap.offset at
   BAR selected by cap.bar and store the first cap.length bytes in
   pci_cfg_data.

So, for a write, we copy into the pci_cfg_data window, then write from
there out to the BAR.  This works correctly if cap.length != width of
write.  Similarly, for a read, we read into window from the BAR then
read the value from there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This is a magic register which causes a character to be outputted: it can
be used even before the device is configured.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The demonstration launcher now uses PCI entirely.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

We only support virtio 1.0 now
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

The only real change here (other than using the PCI bus) is that we
didn't negotiate VIRTIO_NET_F_MRG_RXBUF before, so the format of the
packet header changed with virtio 1.0; we need TUNSETVNETHDRSZ on the
tun fd to tell it about the extra two bytes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

We remove SCSI support (which was removed for 1.0) and VIRTIO_BLK_F_FLUSH
feature flag (removed too, since it's compulsory for 1.0).

The rest is mainly mechanical.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Otherwise Linux fails to find the bus.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

We want to use the local kernel headers, but -I../../include/uapi leads us into
a world of hurt.  Instead we create a dummy include/ dir with symlinks.

If we just use #include "../../include/uapi/linux/virtio_blk.h" we get:

	../../include/uapi/linux/virtio_blk.h:31:32: fatal error: linux/virtio_types.h: No such file or directory
	 #include <linux/virtio_types.h>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

For each device, We need to include the vendor capabilities to demark
where virtio common, notification and ISR regions are (we put them
all in BAR0).

We need to handle the switching of the virtqueues using the accessors.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This handles ioport 0xCF8 and 0xCFC accesses, which are used to
read/write PCI device config space.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

We don't do anything with them yet (emulate_mmio_write and
emulate_mmio_read are stubs), but we decode the instructions and
search for the device they're hitting.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This is where we point our PCI BARs, so that we can intercept MMIO
accesses.  We tell the kernel about it so any faults in this area are
directed to us.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This lets us deliver interrupts for our emulated PCI devices using our
dumb PIC, and not emulate an 8259 and PCI irq mapping tables or whatever.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Once we add PCI, it starts trying to manage our interrupts.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This lets us implement PCI.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

This no longer speeds up boot (IDE got better, I guess), but it does stop
us probing for a PCI bus.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

While hacking on getting I/O out to the lguest launcher, I noticed
that returning 0xFF for the PS/2 keyboard status made it spin for a
while thinking there was a key pending.  Fix this by returning 1
instead of 0xFF.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>