- 01 Jun, 2015 40 commits
-
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
Zhangfei Gao <zhangfei.gao@linaro.org> CC: Peter Griffin <peter.griffin@linaro.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
-
Zhangfei Gao authored
Make the modalias match driver name, this is required to make module auto-loading work. Signed-off-by:
-
Lars-Peter Clausen authored
Use the new MMC_CAP2_NO_WRITE_PROTECT to let the core handle the case where no write protect line is present instead of having custom driver code to handle it. dw_mci_of_get_slot_quirks() is slightly refactored to directly modify the mmc_host capabilities instead of returning a quirk mask. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Zhangfei Gao authored
Support hi6220, tested on hikey board emmc: support hs sd: support hs, sdr12, sdr25 Signed-off-by:
Jorge A. Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by:
Dan Yuan <yuandan@hisilicon.com> Signed-off-by:
-
Zhangfei Gao authored
switch_voltage is required on some platform since special register accessing Signed-off-by:
-
Zhangfei Gao authored
Add bindings for hi6220 mmc support Signed-off-by:
-
Kuninori Morimoto authored
card->csd.capacity is defined as "unsigned int", and sector_t is defined as "u64" or "unsigned long" (depends on CONFIG_LBDAF). Thus, sector_t data might have strange data (see below). This patch cast it to typeof(sector_t) Special thanks to coverity <http://www.coverity.com> ex) if sector_t was u64 unsigned int data; sector_t sector; data = 0x800000; sector = (data << 8); // 0xffffffff80000000 sector = (((typeof(sector_t))data) << 8); // 0x80000000 or data = 0x80000000; sector = (data << 8); // 0x0 sector = (((typeof(sector_t))data) << 8); // 0x8000000000 Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
card->ext_csd.enhanced_area_offset is defined as "unsigned long long", and, ext_csd[] is defined as u8. unsigned long long data might have strange data if first bit of ext_csd[] was 1. this patch cast it to (unsigned long long) Special thanks to coverity <http://www.coverity.com> ex) u8 data8; u64 data64; data8 = 0x80; data64 = (data8 << 24); // 0xffffffff80000000 data64 = (((unsigned long long)data8) << 24); // 0x80000000; Signed-off-by:
-
Fabio Estevam authored
Use BUG_ON() instead of an 'if' condition followed by BUG(). The semantic patch that makes this change is available in scripts/coccinelle/misc/bugon.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
-
Fabio Estevam authored
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/Signed-off-by:
-
Fabio Estevam authored
The only user of this driver that has not been converted to fully device tree is the i.MX35 SoC. There is a i.MX35-based board (mach-pcm043.c) that uses platform data to pass wp_gpio and cd_gpio information. Commit 8d86e4fc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()") broke the platform data case by removing mmc_gpio_request_ro() and mmc_gpio_request_cd(), so restore the functionality for the non-dt case. Also, restore the check for ESDHC_CD_CONTROLLER so that we can still support the "fsl,cd-controller" property. Signed-off-by:
-
Fabio Estevam authored
mmc_of_parse() should be placed inside sdhci_esdhc_imx_probe_dt() as it suits only for the dt case. Signed-off-by:
-
Lars-Peter Clausen authored
Allow to specify in the device-tree that no physical write-protect signal is connected to a particular instance of a MMC controller. Setting the property will cause the core will assume that the SD card is always read-write. The name for the new property is 'disable-wp' and was chosen based on the property with the same function from the Synopsys designware mobile storage host controller DT bindings specification. Signed-off-by:
-
Lars-Peter Clausen authored
It is not uncommon to see systems where there is no physical write-protect signal (e.g. when using eMMC or microSD card slots). For some controllers, which have a dedicated write-protection detection logic (like SDHCI controllers), the get_ro() callback can return bogus data in such a case. Instead of handling this on a per controller basis this patch adds a new capability flag to the MMC core that can be set to specify that the result of get_ro() is invalid. When the flag is set the core will not call get_ro() and assume that the card is always read-write. Signed-off-by:
-
Adrian Hunter authored
Check the error code for EOPNOTSUPP and do not print reset warning in that case. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Adrian Hunter authored
Retry errored data requests when re-tuning is needed and add a flag to struct mmc_blk_request so that the retry is only done once. Signed-off-by:
-
Adrian Hunter authored
If re-tuning is needed, do it in the recovery path to give recovery commands a better chance of success. Signed-off-by:
-
Adrian Hunter authored
CRC errors could possibly be alleviated by re-tuning so flag re-tuning needed in those cases. Note this has no effect if re-tuning has not been enabled. Signed-off-by:
-
Adrian Hunter authored
Make use of mmc core support for re-tuning instead of doing it all in the sdhci driver. This patch also changes to flag the need for re-tuning always after runtime suspend when tuning has been used at initialization. Previously it was only done if the re-tuning timer was in use. Signed-off-by:
-
Adrian Hunter authored
HS400 re-tuning must be done in HS200 mode. Add the ability to switch from HS400 mode to HS200 mode before re-tuning and switch back to HS400 after re-tuning. Signed-off-by:
-
Adrian Hunter authored
Make a separate function to do the mmc_switch status check so it can be re-used. This is preparation for adding support for HS400 re-tuning. Signed-off-by:
-
Adrian Hunter authored
The sleep command is issued after deselecting the card, but re-tuning won't work on a deselected card so re-tuning must be held. Signed-off-by:
-
Adrian Hunter authored
Hold re-tuning during bkops to prevent it from conflicting with the busy state. Signed-off-by:
-
Adrian Hunter authored
Hold re-tuning during erase commands to prevent it from conflicting with the sequence of commands. Signed-off-by:
-
Adrian Hunter authored
Hold re-tuning during switch commands to prevent it from conflicting with the busy state or the CMD13 verification. Signed-off-by:
-
Adrian Hunter authored
At the start of each request, re-tune if needed and then hold off re-tuning again until the request is done. Note that though there is one function that starts requests (mmc_start_request) there are two that wait for the request to be done (mmc_wait_for_req_done and mmc_wait_for_data_req_done). Also note that mmc_wait_for_data_req_done can return even when the request is not done (which allows the block driver to prepare a newly arrived request while still waiting for the previous request). This patch ensures re-tuning is held for the duration of a request. Subsequent patches will also hold re-tuning at other times when it might cause a conflict. In addition, possibly a command is failing because re-tuning is needed. Use mmc_retune_recheck() to check re-tuning. At that point re-tuning is held, at least by the request, so mmc_retune_recheck() flags host->retune_now if the hold count is 1. Signed-off-by:
-
Adrian Hunter authored
Enable re-tuning when tuning is executed and disable re-tuning when card is no longer initialized. In the case of SDIO suspend, the card can keep power. In that case, re-tuning need not be disabled, but, if a re-tuning timer is being used, ensure it is disabled and assume that re-tuning will be needed upon resume since it is not known how long the suspend will last. Signed-off-by:
-
Adrian Hunter authored
Currently, there is core support for tuning during initialization. There can also be a need to re-tune periodically (e.g. sdhci) or to re-tune after the host controller is powered off (e.g. after PM runtime suspend / resume) or to re-tune in response to CRC errors. The main requirements for re-tuning are: - ability to enable / disable re-tuning - ability to flag that re-tuning is needed - ability to re-tune before any request - ability to hold off re-tuning if the card is busy - ability to hold off re-tuning if re-tuning is in progress - ability to run a re-tuning timer To support those requirements 7 members are added to struct mmc_host: unsigned int can_retune:1; /* re-tuning can be used */ unsigned int doing_retune:1; /* re-tuning in progress */ unsigned int retune_now:1; /* do re-tuning at next req */ int need_retune; /* re-tuning is needed */ int hold_retune; /* hold off re-tuning */ unsigned int retune_period; /* re-tuning period in secs */ struct timer_list retune_timer; /* for periodic re-tuning */ need_retune is an integer so it can be set without needing synchronization. hold_retune is a integer to allow nesting. Various simple functions are provided to set / clear those variables. Subsequent patches take those functions into use. Signed-off-by:
-
Axel Lin authored
This eliminates having an #ifdef returning NULL for the case when OF is disabled. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Suman Tripathi authored
This patch adds the quirks and compatible string in sdhci-of-arasan.c to support sdhci-arasan4.9a version of controller. Signed-off-by:
Suman Tripathi <stripathi@apm.com> Reviewed-by:
Michal Simek <michal.simek@xilinx.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Weijun Yang authored
chips have some issues for version and capbility registers, here we fake them. Signed-off-by:
Weijun Yang <Weijun.Yang@csr.com> Signed-off-by:
Barry Song <Baohua.Song@csr.com> Signed-off-by:
-
