- 03 Jan, 2014 40 commits
-
-
Liu Gang authored
commit 1aeef303 upstream. For MPC8572/MPC8536, the status of GPIOs defined as output cannot be determined by reading GPDAT register, so the code use shadow data register instead. But the code may give the wrong status of GPIOs defined as input under some scenarios: 1. If some pins were configured as inputs and were asserted high before booting the kernel, the shadow data has been initialized with those pin values. 2. Some pins have been configured as output first and have been set to the high value, then reconfigured as input. The above cases will make the shadow data for those input pins to be set to high. Then reading the pin status will always return high even if the actual pin status is low. The code should eliminate the effects of the shadow data to the input pins, and the status of those pins should be read directly from GPDAT. Acked-by:
Scott Wood <scottwood@freescale.com> Acked-by:
Anatolij Gustschin <agust@denx.de> Signed-off-by:
Liu Gang <Gang.Liu@freescale.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Colin Leitner authored
commit a3132499 upstream. This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a value of 0 and the CSIZE setting has been skipped altogether by the enclosing if. Tested on 3.11.6 and the scope shows the correct output after the fix has been applied. Tagged to be added to stable, because it fixes a user visible driver bug and is simple enough to backport easily. Signed-off-by:
Colin Leitner <colin.leitner@gmail.com> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: - Old code is cosmetically different] Signed-off-by:
-
Colin Leitner authored
commit 8704211f upstream. FTDI UARTs support only 7 or 8 data bits. Until now the ftdi_sio driver would only report this limitation for CS6 to dmesg and fail to reflect this fact to tcgetattr. This patch reverts the unsupported CSIZE setting and reports the fact with less severance to dmesg for both CS5 and CS6. To test the patch it's sufficient to call stty -F /dev/ttyUSB0 cs5 which will succeed without the patch and report an error with the patch applied. As an additional fix this patch ensures that the control request will always include a data bit size. Signed-off-by:
-
Colin Leitner authored
commit 78692cc3 upstream. This patch removes an erroneous check of CSIZE, which made it impossible to set CS5. Compiles clean, but couldn't test against hardware. Signed-off-by:
-
Colin Leitner authored
commit 711fbdfb upstream. This patch removes an erroneous check of CSIZE, which made it impossible to set CS5. Compiles clean, but couldn't test against hardware. Signed-off-by:
-
Fangxiaozhi (Franko) authored
commit 2bf308d7 upstream. Add new supporting declarations to option.c, to support Huawei new devices with new bInterfaceProtocol value. Signed-off-by:
fangxiaozhi <huananhu@huawei.com> Signed-off-by:
-
Gustavo Zacarias authored
commit 8f173e22 upstream. Interface 1 on this device isn't for option to bind to otherwise an oops on usb_wwan with log flooding will happen when accessing the port: tty_release: ttyUSB1: read/write wait queue active! It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add it there - it's likely used by the card reader. Signed-off-by:
Gustavo Zacarias <gustavo@zacarias.com.ar> Signed-off-by:
-
James Bottomley authored
commit a1470c7b upstream. Bug report from: wenxiong@linux.vnet.ibm.com The issue is happened in dual controller configuration. We got the sysfs warnings when rmmod the ipr module. enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister() for each componment deivce, device_unregister() ->device_del()->kobject_del() ->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL. For each componment device, enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link() in which checking kobj->sd again, it has been set as NULL when doing device_unregister. So we saw all these sysfs WARNING. Tested-by: wenxiong@linux.vnet.ibm.com Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Stephen M. Cameron authored
commit 88bf6d62 upstream. A return value of 1 is interpreted as an error. See pci_driver. in local_pci_probe(). If you're wondering how this ever could have worked, it's because it used to be the case that only return values less than zero were interpreted as failure. But even in the current kernel if the driver registers its various entry points with the kernel, and then returns a value which is interpreted as failure, those registrations aren't undone, so the driver still mostly works. However, the driver's remove function wouldn't be called on rmmod, and pci power management functions wouldn't work. In the case of Smart Array, since it has a battery backed cache (or else no cache) even if the driver is not shut down properly as long as there is no outstanding i/o, nothing too bad happens, which is why it took so long to notice. Requesting backport to stable because the change to pci-driver.c which requires driver probe functions to return 0 occurred between 2.6.35 and 2.6.36 (the pci power management breakage) and again between 3.7 and 3.8 (pci_dev->driver getting set to NULL in local_pci_probe() preventing driver remove function from being called on rmmod.) Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
commit 2e311fba upstream. We inadvertantly discarded the scsi status for aborted commands. For some commands (e.g. reads from tape drives) these can't be retried, and if we discarded the scsi status, the scsi mid layer couldn't notice anything was wrong and the error was not reported. Signed-off-by:
-
Russell King authored
commit 43659222 upstream. It's no good setting vga_base after the VGA console has been initialised, because if we do that we get this: Unable to handle kernel paging request at virtual address 000b8000 pgd = c0004000 [000b8000] *pgd=07ffc831, *pte=00000000, *ppte=00000000 0Internal error: Oops: 5017 [#1] ARM Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0+ #49 task: c03e2974 ti: c03d8000 task.ti: c03d8000 PC is at vgacon_startup+0x258/0x39c LR is at request_resource+0x10/0x1c pc : [<c01725d0>] lr : [<c0022b50>] psr: 60000053 sp : c03d9f68 ip : 000b8000 fp : c03d9f8c r10: 000055aa r9 : 4401a103 r8 : ffffaa55 r7 : c03e357c r6 : c051b460 r5 : 000000ff r4 : 000c0000 r3 : 000b8000 r2 : c03e0514 r1 : 00000000 r0 : c0304971 Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel which is an access to the 0xb8000 without the PCI offset required to make it work. Fixes: cc22b4c1 ("ARM: set vga memory base at run-time") Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Shawn Landden authored
commit d3f7d56a upstream. Commit 35f9c09f (tcp: tcp_sendpages() should call tcp_push() once) added an internal flag MSG_SENDPAGE_NOTLAST, similar to MSG_MORE. algif_hash, algif_skcipher, and udp used MSG_MORE from tcp_sendpages() and need to see the new flag as identical to MSG_MORE. This fixes sendfile() on AF_ALG. v3: also fix udp Cc: Tom Herbert <therbert@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Reported-and-tested-by:
Shawn Landden <shawnlandden@gmail.com> Original-patch: Richard Weinberger <richard@nod.at> Signed-off-by:
Shawn Landden <shawn@churchofgit.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Linus Walleij authored
commit a0c20fb0 upstream. After commit e9e4ea74 "net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data" The Versatile SMSC LAN91C111 is crashing like this: ------------[ cut here ]------------ kernel BUG at /home/linus/linux/drivers/net/ethernet/smsc/smc91x.c:599! Internal error: Oops - BUG: 0 [#1] ARM Modules linked in: CPU: 0 PID: 43 Comm: udhcpc Not tainted 3.13.0-rc1+ #24 task: c6ccfaa0 ti: c6cd0000 task.ti: c6cd0000 PC is at smc_hardware_send_pkt+0x198/0x22c LR is at smc_hardware_send_pkt+0x24/0x22c pc : [<c01be324>] lr : [<c01be1b0>] psr: 20000013 sp : c6cd1d08 ip : 00000001 fp : 00000000 r10: c02adb08 r9 : 00000000 r8 : c6ced802 r7 : c786fba0 r6 : 00000146 r5 : c8800000 r4 : c78d6000 r3 : 0000000f r2 : 00000146 r1 : 00000000 r0 : 00000031 Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 0005317f Table: 06cf4000 DAC: 00000015 Process udhcpc (pid: 43, stack limit = 0xc6cd01c0) Stack: (0xc6cd1d08 to 0xc6cd2000) 1d00: 00000010 c8800000 c78d6000 c786fba0 c78d6000 c01be868 1d20: c01be7a4 00004000 00000000 c786fba0 c6c12b80 c0208554 000004d0 c780fc60 1d40: 00000220 c01fb734 00000000 00000000 00000000 c6c9a440 c6c12b80 c78d6000 1d60: c786fba0 c6c9a440 00000000 c021d1d8 00000000 00000000 c6c12b80 c78d6000 1d80: c786fba0 00000001 c6c9a440 c02087f8 c6c9a4a0 00080008 00000000 00000000 1da0: c78d6000 c786fba0 c78d6000 00000138 00000000 00000000 00000000 00000000 1dc0: 00000000 c027ba74 00000138 00000138 00000001 00000010 c6cedc00 00000000 1de0: 00000008 c7404400 c6cd1eec c6cd1f14 c067a73c c065c0b8 00000000 c067a740 1e00: 01ffffff 002040d0 00000000 00000000 00000000 00000000 00000000 ffffffff 1e20: 43004400 00110022 c6cdef20 c027ae8c c6ccfaa0 be82d65c 00000014 be82d3cc 1e40: 00000000 00000000 00000000 c01f2870 00000000 00000000 00000000 c6cd1e88 1e60: c6ccfaa0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1e80: 00000000 00000000 00000031 c7802310 c7802300 00000138 c7404400 c0771da0 1ea0: 00000000 c6cd1eec c7800340 00000138 be82d65c 00000014 be82d3cc c6cd1f08 1ec0: 00000014 00000000 c7404400 c7404400 00000138 c01f4628 c78d6000 00000000 1ee0: 00000000 be82d3cc 00000138 c6cd1f08 00000014 c6cd1ee4 00000001 00000000 1f00: 00000000 00000000 00080011 00000002 06000000 ffffffff 0000ffff 00000002 1f20: 06000000 ffffffff 0000ffff c00928c8 c065c520 c6cd1f58 00000003 c009299c 1f40: 00000003 c065c520 c7404400 00000000 c7404400 c01f2218 c78106b0 c7441cb0 1f60: 00000000 00000006 c06799fc 00000000 00000000 00000006 00000000 c01f3ee0 1f80: 00000000 00000000 be82d678 be82d65c 00000014 00000001 00000122 c00139c8 1fa0: c6cd0000 c0013840 be82d65c 00000014 00000006 be82d3cc 00000138 00000000 1fc0: be82d65c 00000014 00000001 00000122 00000000 00000000 00018cb1 00000000 1fe0: 00003801 be82d3a8 0003a0c7 b6e9af08 60000010 00000006 00000000 00000000 [<c01be324>] (smc_hardware_send_pkt+0x198/0x22c) from [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) from [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) from [<c021d1d8>] (sch_direct_xmit+0x94/0x18c) [<c021d1d8>] (sch_direct_xmit+0x94/0x18c) from [<c02087f8>] (dev_queue_xmit+0x238/0x42c) [<c02087f8>] (dev_queue_xmit+0x238/0x42c) from [<c027ba74>] (packet_sendmsg+0xbe8/0xd28) [<c027ba74>] (packet_sendmsg+0xbe8/0xd28) from [<c01f2870>] (sock_sendmsg+0x84/0xa8) [<c01f2870>] (sock_sendmsg+0x84/0xa8) from [<c01f4628>] (SyS_sendto+0xb8/0xdc) [<c01f4628>] (SyS_sendto+0xb8/0xdc) from [<c0013840>] (ret_fast_syscall+0x0/0x2c) Code: e3130002 1a000001 e3130001 0affffcd (e7f001f2) ---[ end trace 81104fe70e8da7fe ]--- Kernel panic - not syncing: Fatal exception in interrupt This is because the macro operations in smc91x.h defined for Versatile are missing SMC_outsw() as used in this commit. The Versatile needs and uses the same accessors as the other platforms in the first if(...) clause, just switch it to using that and we have one problem less to worry about. This includes a hunk of a patch from Will Deacon fixin the other 32bit platforms as well: Innokom, Ramses, PXA, PCM027. Checkpatch complains about spacing, but I have opted to follow the style of this .h-file. Cc: Russell King <linux@arm.linux.org.uk> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Wei Yongjun authored
commit 89f4d45b upstream. In case of error, the function kthread_run() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Horia Geanta authored
commit 5638cabf upstream. There are cases when cryptlen can be zero in crypto_ccm_auth(): -encryptiom: input scatterlist length is zero (no plaintext) -decryption: input scatterlist contains only the mac plus the condition of having different source and destination buffers (or else scatterlist length = max(plaintext_len, ciphertext_len)). These are not handled correctly, leading to crashes like: root@p4080ds:~/crypto# insmod tcrypt.ko mode=45 ------------[ cut here ]------------ kernel BUG at crypto/scatterwalk.c:37! Oops: Exception in kernel mode, sig: 5 [#1] SMP NR_CPUS=8 P4080 DS Modules linked in: tcrypt(+) crc32c xts xcbc vmac pcbc ecb gcm ghash_generic gf128mul ccm ctr seqiv CPU: 3 PID: 1082 Comm: cryptomgr_test Not tainted 3.11.0 #14 task: ee12c5b0 ti: eecd0000 task.ti: eecd0000 NIP: c0204d98 LR: f9225848 CTR: c0204d80 REGS: eecd1b70 TRAP: 0700 Not tainted (3.11.0) MSR: 00029002 <CE,EE,ME> CR: 22044022 XER: 20000000 GPR00: f9225c94 eecd1c20 ee12c5b0 eecd1c28 ee879400 ee879400 00000000 ee607464 GPR08: 00000001 00000001 00000000 006b0000 c0204d80 00000000 00000002 c0698e20 GPR16: ee987000 ee895000 fffffff4 ee879500 00000100 eecd1d58 00000001 00000000 GPR24: ee879400 00000020 00000000 00000000 ee5b2800 ee607430 00000004 ee607460 NIP [c0204d98] scatterwalk_start+0x18/0x30 LR [f9225848] get_data_to_compute+0x28/0x2f0 [ccm] Call Trace: [eecd1c20] [f9225974] get_data_to_compute+0x154/0x2f0 [ccm] (unreliable) [eecd1c70] [f9225c94] crypto_ccm_auth+0x184/0x1d0 [ccm] [eecd1cb0] [f9225d40] crypto_ccm_encrypt+0x60/0x2d0 [ccm] [eecd1cf0] [c020d77c] __test_aead+0x3ec/0xe20 [eecd1e20] [c020f35c] test_aead+0x6c/0xe0 [eecd1e40] [c020f420] alg_test_aead+0x50/0xd0 [eecd1e60] [c020e5e4] alg_test+0x114/0x2e0 [eecd1ee0] [c020bd1c] cryptomgr_test+0x4c/0x60 [eecd1ef0] [c0047058] kthread+0xa8/0xb0 [eecd1f40] [c000eb0c] ret_from_kernel_thread+0x5c/0x64 Instruction dump: 0f080000 81290024 552807fe 0f080000 5529003a 4bffffb4 90830000 39400000 39000001 8124000c 2f890000 7d28579e <0f090000> 81240008 91230004 4e800020 ---[ end trace 6d652dfcd1be37bd ]--- Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
Horia Geanta <horia.geanta@freescale.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Gerald Schaefer authored
commit 9dda2769 upstream. Some s390 crypto algorithms incorrectly use the crypto_tfm structure to store private data. As the tfm can be shared among multiple threads, this can result in data corruption. This patch fixes aes-xts by moving the xts and pcc parameter blocks from the tfm onto the stack (48 + 96 bytes). Signed-off-by:
Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
-
Tom Lendacky authored
commit 41da8b5a upstream. The scatterwalk_crypto_chain function invokes the scatterwalk_sg_chain function to chain two scatterlists, but the chain pointer indication bit is not set. When the resulting scatterlist is used, for example, by sg_nents to count the number of scatterlist entries, a segfault occurs because sg_nents does not follow the chain pointer to the chained scatterlist. Update scatterwalk_sg_chain to set the chain pointer indication bit as is done by the sg_chain function. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Tom Lendacky authored
commit fc019c71 upstream. When performing an asynchronous ablkcipher operation the authenc completion callback routine is invoked, but it does not locate and use the proper IV. The callback routine, crypto_authenc_encrypt_done, is updated to use the same method of calculating the address of the IV as is done in crypto_authenc_encrypt function which sets up the callback. Signed-off-by:
-
Peter Zijlstra authored
commit 0fc0287c upstream. Juri hit the below lockdep report: [ 4.303391] ====================================================== [ 4.303392] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ] [ 4.303394] 3.12.0-dl-peterz+ #144 Not tainted [ 4.303395] ------------------------------------------------------ [ 4.303397] kworker/u4:3/689 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 4.303399] (&p->mems_allowed_seq){+.+...}, at: [<ffffffff8114e63c>] new_slab+0x6c/0x290 [ 4.303417] [ 4.303417] and this task is already holding: [ 4.303418] (&(&q->__queue_lock)->rlock){..-...}, at: [<ffffffff812d2dfb>] blk_execute_rq_nowait+0x5b/0x100 [ 4.303431] which would create a new lock dependency: [ 4.303432] (&(&q->__queue_lock)->rlock){..-...} -> (&p->mems_allowed_seq){+.+...} [ 4.303436] [ 4.303898] the dependencies between the lock to be acquired and SOFTIRQ-irq-unsafe lock: [ 4.303918] -> (&p->mems_allowed_seq){+.+...} ops: 2762 { [ 4.303922] HARDIRQ-ON-W at: [ 4.303923] [<ffffffff8108ab9a>] __lock_acquire+0x65a/0x1ff0 [ 4.303926] [<ffffffff8108cbe3>] lock_acquire+0x93/0x140 [ 4.303929] [<ffffffff81063dd6>] kthreadd+0x86/0x180 [ 4.303931] [<ffffffff816ded6c>] ret_from_fork+0x7c/0xb0 [ 4.303933] SOFTIRQ-ON-W at: [ 4.303933] [<ffffffff8108abcc>] __lock_acquire+0x68c/0x1ff0 [ 4.303935] [<ffffffff8108cbe3>] lock_acquire+0x93/0x140 [ 4.303940] [<ffffffff81063dd6>] kthreadd+0x86/0x180 [ 4.303955] [<ffffffff816ded6c>] ret_from_fork+0x7c/0xb0 [ 4.303959] INITIAL USE at: [ 4.303960] [<ffffffff8108a884>] __lock_acquire+0x344/0x1ff0 [ 4.303963] [<ffffffff8108cbe3>] lock_acquire+0x93/0x140 [ 4.303966] [<ffffffff81063dd6>] kthreadd+0x86/0x180 [ 4.303969] [<ffffffff816ded6c>] ret_from_fork+0x7c/0xb0 [ 4.303972] } Which reports that we take mems_allowed_seq with interrupts enabled. A little digging found that this can only be from cpuset_change_task_nodemask(). This is an actual deadlock because an interrupt doing an allocation will hit get_mems_allowed()->...->__read_seqcount_begin(), which will spin forever waiting for the write side to complete. Cc: John Stultz <john.stultz@linaro.org> Cc: Mel Gorman <mgorman@suse.de> Reported-by:
Juri Lelli <juri.lelli@gmail.com> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Tested-by:
Li Zefan <lizefan@huawei.com> Acked-by:
Mel Gorman <mgorman@suse.de> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 930ba4a3 upstream. There seems to be no active maintainer for the driver, and there is an unfixed security bug, so disable the driver for now. Hopefully someone steps up to be the maintainer, and works to get this out of staging, otherwise it will be deleted soon. Reported-by:
Nico Golde <nico@ngolde.de> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Omar Ramirez Luna <omar.ramirez@copitl.com> Cc: Omar Ramirez Luna <omar.ramirez@ti.com> Cc: Kanigeri, Hari <h-kanigeri2@ti.com> Cc: Ameya Palande <ameya.palande@nokia.com> Cc: Guzman Lugo, Fernando <fernando.lugo@ti.com> Cc: Hebbar, Shivananda <x0hebbar@ti.com> Cc: Ramos Falcon, Ernesto <ernesto@ti.com> Cc: Felipe Contreras <felipe.contreras@gmail.com> Cc: Anna, Suman <s-anna@ti.com> Cc: Gupta, Ramesh <grgupta@ti.com> Cc: Gomez Castellanos, Ivan <ivan.gomez@ti.com> Cc: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: Armando Uribe De Leon <x0095078@ti.com> Cc: Deepak Chitriki <deepak.chitriki@ti.com> Cc: Menon, Nishanth <nm@ti.com> Cc: Phil Carmody <ext-phil.2.carmody@nokia.com> Cc: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by:
-
Dan Williams authored
commit ae5fbae0 upstream. Since commit 110dd8f1 "[SCSI] libsas: fix scr_read/write users and update the libata documentation" we have been passing pmp=1 and is_cmd=0 to ata_tf_to_fis(). Praveen reports that eSATA attached drives do not discover correctly. His investigation found that the BIOS was passing pmp=0 while Linux was passing pmp=1 and failing to discover the drives. Update libsas to follow the libata example of pulling the pmp setting from the ata_link and correct is_cmd to be 1 since all tf's submitted through ->qc_issue are commands. Presumably libsas lldds do not care about is_cmd as they have sideband mechanisms to perform link management. http://marc.info/?l=linux-scsi&m=138179681726990 [jejb: checkpatch fix] Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Reported-by:
Praveen Murali <pmurali@logicube.com> Tested-by:
-
Steven Rostedt (Red Hat) authored
commit 4e58e547 upstream. If an TRACE_EVENT() uses __assign_str() or __get_str on a NULL pointer then the following oops will happen: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<c127a17b>] strlen+0x10/0x1a *pde = 00000000 ^M Oops: 0000 [#1] PREEMPT SMP Modules linked in: CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.13.0-rc1-test+ #2 Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006^M task: f5cde9f0 ti: f5e5e000 task.ti: f5e5e000 EIP: 0060:[<c127a17b>] EFLAGS: 00210046 CPU: 1 EIP is at strlen+0x10/0x1a EAX: 00000000 EBX: c2472da8 ECX: ffffffff EDX: c2472da8 ESI: c1c5e5fc EDI: 00000000 EBP: f5e5fe84 ESP: f5e5fe80 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 CR0: 8005003b CR2: 00000000 CR3: 01f32000 CR4: 000007d0 Stack: f5f18b90 f5e5feb8 c10687a8 0759004f 00000005 00000005 00000005 00200046 00000002 00000000 c1082a93 f56c7e28 c2472da8 c1082a93 f5e5fee4 c106bc61^M 00000000 c1082a93 00000000 00000000 00000001 00200046 00200082 00000000 Call Trace: [<c10687a8>] ftrace_raw_event_lock+0x39/0xc0 [<c1082a93>] ? ktime_get+0x29/0x69 [<c1082a93>] ? ktime_get+0x29/0x69 [<c106bc61>] lock_release+0x57/0x1a5 [<c1082a93>] ? ktime_get+0x29/0x69 [<c10824dd>] read_seqcount_begin.constprop.7+0x4d/0x75 [<c1082a93>] ? ktime_get+0x29/0x69^M [<c1082a93>] ktime_get+0x29/0x69 [<c108a46a>] __tick_nohz_idle_enter+0x1e/0x426 [<c10690e8>] ? lock_release_holdtime.part.19+0x48/0x4d [<c10bc184>] ? time_hardirqs_off+0xe/0x28 [<c1068c82>] ? trace_hardirqs_off_caller+0x3f/0xaf [<c108a8cb>] tick_nohz_idle_enter+0x59/0x62 [<c1079242>] cpu_startup_entry+0x64/0x192 [<c102299c>] start_secondary+0x277/0x27c Code: 90 89 c6 89 d0 88 c4 ac 38 e0 74 09 84 c0 75 f7 be 01 00 00 00 89 f0 48 5e 5d c3 55 89 e5 57 66 66 66 66 90 83 c9 ff 89 c7 31 c0 <f2> ae f7 d1 8d 41 ff 5f 5d c3 55 89 e5 57 66 66 66 66 90 31 ff EIP: [<c127a17b>] strlen+0x10/0x1a SS:ESP 0068:f5e5fe80 CR2: 0000000000000000 ---[ end trace 01bc47bf519ec1b2 ]--- New tracepoints have been added that have allowed for NULL pointers being assigned to strings. To fix this, change the TRACE_EVENT() code to check for NULL and if it is, it will assign "(null)" to it instead (similar to what glibc printf does). Reported-by:
Shuah Khan <shuah.kh@samsung.com> Reported-by:
Jovi Zhangwei <jovi.zhangwei@gmail.com> Link: http://lkml.kernel.org/r/CAGdX0WFeEuy+DtpsJzyzn0343qEEjLX97+o1VREFkUEhndC+5Q@mail.gmail.com Link: http://lkml.kernel.org/r/528D6972.9010702@samsung.com Fixes: 9cbf1176 ("tracing/events: provide string with undefined size support") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Kailang Yang authored
commit 9ad54547 upstream. Set the missing pcbeep default amp for ALC668. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kailang Yang authored
commit ba4c4d0a upstream. It's compatible with ALC269. Signed-off-by:
-
Laxman Dewangan authored
commit ac01810c upstream. When the system enters suspend, it disables all interrupts in suspend_device_irqs(), including the interrupts marked EARLY_RESUME. On the resume side things are different. The EARLY_RESUME interrupts are reenabled in sys_core_ops->resume and the non EARLY_RESUME interrupts are reenabled in the normal system resume path. When suspend_noirq() failed or suspend is aborted for any other reason, we might omit the resume side call to sys_core_ops->resume() and therefor the interrupts marked EARLY_RESUME are not reenabled and stay disabled forever. To solve this, enable all irqs unconditionally in irq_resume() regardless whether interrupts marked EARLY_RESUMEhave been already enabled or not. This might try to reenable already enabled interrupts in the non failure case, but the only affected platform is XEN and it has been confirmed that it does not cause any side effects. [ tglx: Massaged changelog. ] Signed-off-by:
Laxman Dewangan <ldewangan@nvidia.com> Acked-by-and-tested-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
Pavel Machek <pavel@ucw.cz> Cc: <ian.campbell@citrix.com> Cc: <rjw@rjwysocki.net> Cc: <len.brown@intel.com> Cc: <gregkh@linuxfoundation.org> Link: http://lkml.kernel.org/r/1385388587-16442-1-git-send-email-ldewangan@nvidia.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Oliver Hartkopp authored
commit 2fea6cd3 upstream. This patch fixes the issue that the sja1000_interrupt() function may have returned IRQ_NONE without processing the optional pre_irq() and post_irq() function before. Further the irq processing counter 'n' is moved to the end of the while statement to return correct IRQ_[NONE|HANDLED] values at error conditions. Reported-by:
Wolfgang Grandegger <wg@grandegger.com> Acked-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> [bwh: Backported to 3.2: s/SJA1000_IER/REG_IER/; s/SJA1000_IR/REG_IR/] Signed-off-by:
-
Rashika Kheria authored
commit 1b672224 upstream. As suggested by Minchan Kim and Jerome Marchand "The code in reset_store get the block device (bdget_disk()) but it does not put it (bdput()) when it's done using it. The usage count is therefore incremented but never decremented." This patch also puts bdput() for all error cases. Acked-by:
Minchan Kim <minchan@kernel.org> Acked-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
Rashika Kheria <rashika.kheria@gmail.com> Signed-off-by:
-
Rashika Kheria authored
commit 46a51c80 upstream. This patch fixes the bug in reset_store caused by accessing NULL pointer. The bdev gets its value from bdget_disk() which could fail when memory pressure is severe and hence can return NULL because allocation of inode in bdget could fail. Hence, this patch introduces a check for bdev to prevent reference to a NULL pointer in the later part of the code. It also removes unnecessary check of bdev for fsync_bdev(). Acked-by:
-
Alan Stern authored
commit a535d81c upstream. The dwc3 UDC driver doesn't implement endpoint wedging correctly. When an endpoint is wedged, the gadget driver should be allowed to clear the wedge by calling usb_ep_clear_halt(). Only the host is prevented from resetting the endpoint. This patch fixes the implementation. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
Pratyush Anand <pratyush.anand@st.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Michael Grzeschik authored
commit 2bac51a1 upstream. The delayed_status value is used to keep track of status response packets on ep0. It needs to be reset or the set_config function would still delay the answer, if the usb device got unplugged while waiting for setup_continue to be called. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
-
Johan Hovold authored
commit 6f648546 upstream. Fix race in generic write implementation, which could lead to temporarily degraded throughput. The current generic write implementation introduced by commit 27c7acf2 ("USB: serial: reimplement generic fifo-based writes") has always had this bug, although it's fairly hard to trigger and the consequences are not likely to be noticed. Specifically, a write() on one CPU while the completion handler is running on another could result in only one of the two write urbs being utilised to empty the remainder of the write fifo (unless there is a second write() that doesn't race during that time). Signed-off-by:
-
Johannes Berg authored
commit 051a41fa upstream. Multicast frames can't be transmitted as part of an aggregation session (such a session couldn't even be set up) so don't try to reorder them. Trying to do so would cause the reorder to stop working correctly since multicast QoS frames (as transmitted by the Aruba APs this was found with) would cause sequence number confusion in the buffer. Reported-by:
Blaise Gassend <blaise@suitabletech.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Mark Brown authored
commit 2ab2b742 upstream. Otherwise we'll skip sync on resume. Signed-off-by:
Mark Brown <broonie@linaro.org> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Michael Neuling authored
commit ec67ad82 upstream. In a recent patch: commit c13f20ac Author: Michael Neuling <mikey@neuling.org> powerpc/signals: Mark VSX not saved with small contexts We fixed an issue but an improved solution was later discussed after the patch was merged. Firstly, this patch doesn't handle the 64bit signals case, which could also hit this issue (but has never been reported). Secondly, the original patch isn't clear what MSR VSX should be set to. The new approach below always clears the MSR VSX bit (to indicate no VSX is in the context) and sets it only in the specific case where VSX is available (ie. when VSX has been used and the signal context passed has space to provide the state). This reverts the original patch and replaces it with the improved solution. It also adds a 64 bit version. Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Samir Benmendil authored
commit 6d5278a6 upstream. Tested with a DAWICONTROL DC-624e on 3.10.10 Signed-off-by:
Samir Benmendil <samir.benmendil@gmail.com> Signed-off-by:
Levente Kurusa <levex@linux.com> Signed-off-by:
-
Xiangliang Yu authored
commit 8e7ee6f5 upstream. Define PCI_VENDOR_ID_MARVELL_EXT macro for 0x1b4b vendor ID Signed-off-by:
Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by:
Myron Stowe <myron.stowe@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Alistair Popple authored
commit 2435dcb9 upstream. The new IBM Akebono board has a PPC476GTR SoC with an AHCI compliant SATA controller. This patch adds a compatible property for the new SoC to the AHCI platform driver. Signed-off-by:
Alistair Popple <alistair@popple.id.au> Signed-off-by:
-
Junxiao Bi authored
commit 76ae281f upstream. A race window in configfs, it starts from one dentry is UNHASHED and end before configfs_d_iput is called. In this window, if a lookup happen, since the original dentry was UNHASHED, so a new dentry will be allocated, and then in configfs_attach_attr(), sd->s_dentry will be updated to the new dentry. Then in configfs_d_iput(), BUG_ON(sd->s_dentry != dentry) will be triggered and system panic. sys_open: sys_close: ... fput dput dentry_kill __d_drop <--- dentry unhashed here, but sd->dentry still point to this dentry. lookup_real configfs_lookup configfs_attach_attr---> update sd->s_dentry to new allocated dentry here. d_kill configfs_d_iput <--- BUG_ON(sd->s_dentry != dentry) triggered here. To fix it, change configfs_d_iput to not update sd->s_dentry if sd->s_count > 2, that means there are another dentry is using the sd beside the one that is going to be put. Use configfs_dirent_lock in configfs_attach_attr to sync with configfs_d_iput. With the following steps, you can reproduce the bug. 1. enable ocfs2, this will mount configfs at /sys/kernel/config and fill configure in it. 2. run the following script. while [ 1 ]; do cat /sys/kernel/config/cluster/$your_cluster_name/idle_timeout_ms > /dev/null; done & while [ 1 ]; do cat /sys/kernel/config/cluster/$your_cluster_name/idle_timeout_ms > /dev/null; done & Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Eric Seppanen authored
commit 86784c6b upstream. In iSCSI negotiations with initiator CHAP enabled, usernames with trailing garbage are permitted, because the string comparison only checks the strlen of the configured username. e.g. "usernameXXXXX" will be permitted to match "username". Just check one more byte so the trailing null char is also matched. Signed-off-by:
Eric Seppanen <eric@purestorage.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Eric Seppanen authored
commit 369653e4 upstream. extract_param() is called with max_length set to the total size of the output buffer. It's not safe to allow a parameter length equal to the buffer size as the terminating null would be written one byte past the end of the output buffer. Signed-off-by:
-
