tlpx_half bit field in DSI_DSIPHY_CFG1 is [20,16], not [22,16] as
accessed in the code currently. Fix this.

The bug should not have caused any problems on OMAP3/4, as the bits
21,22 are unused. They are used on OMAP5, though.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

In OMAP4 and OMAP5 when TILER 2D burst mode is used, a maximum of one line can
be skipped as per the respective TRMs. The MBlockStride OCP signal, which is
sum of ROWINC and image width in memory, is only 17 bits wide. In 2D mode TILER
supports 8192, 16384, 32768 and 65536 values of MBlockStride. In case when 2 or
more lines are skipped the ROWINC value exceeds 65536 resulting in OCP errors.
So, maximum vertical predecimation achievable is 2.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This series adds basic OMAP5 DSS functionality, mainly related to DSS core, DPI
and DSI.

* omap5-dss:
  OMAPDSS: DSI: make OMAP2_DSS_DSI depend on ARCH_OMAP5
  OMAPDSS: DSI: Add code to disable PHY DCC
  OMAPDSS: DSI: Add new linebuffer size for OMAP5
  OMAPDSS: DSI: Add FEAT_DSI_PLL_REFSEL
  OMAPDSS: DSI: Add FEAT_DSI_PLL_SELFREQDCO
  OMAPDSS: Add support for DPI source selection
  OMAPDSS: move dss feats to the end of dss.c
  OMAPDSS: Add basic omap5 features to dss and dispc
  OMAPDSS: DSI: improve DSI clock calcs for DISPC

This series contains patches that change how omapdss's panel devices
(omap_dss_device) are initialized and registered. There are two patches that
change behaviour, the rest are just cleanups:

The patch "omap_dss_register_device() doesn't take display index" affects the
number for the "displayX" sysfs files. This hopefully doesn't affect the
userspace, as the number has never been a clear indication of what the
particular display is.

The patch "register only one display device per output" affects how panel
devices are created. Currently we support multiple panels per output, i.e. you
could have DVI and an LCD displays using the same DPI output, as long as the
DVI and LCD are not used at the same time.

This patch changes the omapdss driver to only register one display device per
output. If there are multiple displays for the output, either the first one is
picked or, if def_display has been defined in kernel parameters and the
def_display is one of the displays for this output, the def_display is picked.
See the patch for more information.

  OMAPDSS: alloc dssdevs dynamically
  OMAPDSS: cleanup dss_recheck_connections further
  OMAPDSS: cleanup dss_recheck_connections
  OMAPDSS: handle errors in dss_init_device
  OMAPDSS: explicitely initialize dssdev->channel for new displays
  OMAPDSS: register only one display device per output
  OMAPDSS: Add dss_get_default_display_name()
  OMAPDSS: omap_dss_register_device() doesn't take display index

On our AM3505 based board, dpi.c complains that there is no VDDS_DSI
regulator and the framebuffer cannot be enabled. However, this check
does not seem to apply to AM3505/17 chips.

This patch adds new features list for AM35xxx, which is the same as for
OMAP3 except the VDDS_DSI is removed.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Change omapdss Kconfig file to make OMAP2_DSS_DSI depend on ARCH_OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP5 DSI PHY has DCC (Duty Cycle Corrector) block, and by default DCC
is enabled and thus the PLL clock is divided by 2 to get the DSI DDR
clk. This divider has been 4 for all previous OMAPs, and changing it
needs some reorganization of the code. The DCC can be disabled, and in
that case the divider is back to the old 4.

This patch adds dss feature for the DCC, and adds code to always disable
the DCC.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP5's DSI has a larger line buffer than earlier OMAPs. This patch adds
support for this to the DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add FEAT_DSI_PLL_REFSEL. OMAP5's DSI PLL needs configuration to select
the reference clock to be used. We always use SYSCLK.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add FEAT_DSI_PLL_SELFREQDCO. OMAP5's DSI PLL has a new configuration
option that needs to be programmed depending on the PLL's output clock
frequency.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We can select the video source for DPI output as follows:

OMAP2/3: always LCD1
OMAP4: LCD2 or DIGIT
OMAP5: LCD1/LCD2/LCD3/DIGIT

This patch adds support to select the source, and makes dpi.c call the
function to set the source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Anders <x0132446@ti.com>

Move dss_features to the end of dss.c the same way they are in dispc.c,
so that we don't have to declare prototypes for static feat-related
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add basic omap5 features for dss and dispc.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Commit ee144e64 added
dsi_pll_calc_ddrfreq() which calculates PLL dividers based on given DSI
bus clock speed. The function works ok, but it can be improved for the
DISPC clock calc.

The current version calculates the clock going from the PLL to the DISPC
simply by setting the clock as close to DISPC maximum as possible, and
the pixel clock is calculated based on that.

This patch changes the function to calculate DISPC clock more
dynamically, iterating through different DISPC clocks and pixel clock
values, and thus we'll get more suitable pixel clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We currently create omap_dss_devices statically in board files, and use
those devices directly in the omapdss driver. This model prevents us
from having the platform data (which the dssdevs in board files
practically are) as read-only, and it's also different than what we will
use with device tree.

This patch changes the model to be in line with DT model: we allocate
the dssdevs dynamically, and initialize them according to the data in
the board file's dssdev (basically we memcopy the dssdev fields).

The allocation and registration is done in the following steps in the
output drivers:

- Use dss_alloc_and_init_device to allocate and initialize the device.
  The function uses kalloc and device_initialize to accomplish this.
- Call dss_copy_device_pdata to copy the data from the board file's
  dssdev
- Use dss_add_device to register the device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Cleanup dss_recheck_connections, move and rename it to a static
dss_init_connections function inside display.c. Improve the function to
return errors, and implement a matching dss_uninit_connections that can
be used to free the mgr->dssdev link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dss_recheck_connections is quite a mess. With the previous commit that
initializes the channel field for HDMI and VENC displays, we can greatly
simplify the dss_recheck_connections.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add error handling to dss_init_device(), which has, for some reason,
been missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

HDMI and VENC outputs always use the DIGIT output from DISPC. The dssdev
struct contains "channel" field which is used to specify the DISPC
output for the display, but this was not used for HDMI and VENC.

This patch fills the channel field explicitely for HDMI and VENC
displays so that we can always rely on the channel field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We have boards with multiple panel devices connected to the same
physical output, of which only one panel can be enabled at one time.
Examples of these are Overo, where you can use different daughter boards
that have different LCDs, and 3430SDP which has an LCD and a DVI output
and a physical switch to select the active display.

These are supported by omapdss so that we add all the possible display
devices at probe, but the displays are inactive until somebody enables
one. At this point the panel driver starts using the DSS, thus reserving
the physcal resource and excluding the other panels.

This is problematic:
- Panel drivers can't allocate their resources properly at probe(),
  because the resources can be shared with other panels. Thus they can
  be only reserved at enable time.
- Managing this in omapdss is confusing. It's not natural to have
  child devices, which may not even exist (for example, a daughterboard
  that is not connected).

Only some boards have multiple displays per output, and of those, only
very few have possibility of switching the display during runtime.
Because of the above points:
- We don't want to make omapdss and all the panel drivers more complex
  just because some boards have complex setups.
- Only few boards support runtime switching, and afaik even then it's
  not required. So we don't need to support runtime switching.

Thus we'll change to a model where we will have only one display device
per output and this cannot be (currently) changed at runtime. We'll
still have the possibility to select the display from multiple options
during boot with the default display option.

This patch accomplishes the above by changing how the output drivers
register the display device. Instead of registering all the devices
given from the board file, we'll only register one. If the default
display option is set, the output driver selects that display from its
displays. If the default display is not set, or the default display is
not one of the output's displays, the output driver selects the first
display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add function dss_get_default_display_name() which returns the name of
the default display, given from the board file or via module parameters.
The default display name can be used by output drivers to decide which
display is the wanted one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We used to have all the displays of the board in one list, and we made a
"displayX" directory in the sysfs, where X was the index of the display
in the list.

This doesn't work anymore with device tree, as there's no single list to
get the number from, and it doesn't work very well even with non-DT as
we need to do some tricks to get the index nowadays.

This patch changes omap_dss_register_device() so that it doesn't take
disp_num as a parameter anymore, but uses a private increasing counter
for the display number.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The framebuffers are cleared with the function omapfb_clear_fb(), which
internally calls cfb_fillrect(). The boot logo is copied on to the
framebuffer when the fb device is registered with fb framework.

omapfb_clear_fb() is called after the framebuffer is registered, leading to
the boot logo getting cleared. Clear the framebuffers using omapfb_clear_fb()
before registering the framebuffer devices.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Merge omapfb and OMAP SDI fixes:

* OMAPFB: fix framebuffer console colors
* OMAPDSS: Fix SDI PLL locking

Conflicts:
	drivers/video/omap2/dss/sdi.c

Most important changes:

* Remove OMAP4 HDMI gpio handling from board files
* Add vdda_hdmi_dac supply for HDMI to twl-common.c
* Calculate DSI clocks dynamically
* Remove DSS clock dividers from 4430sdp board file
* vram.c no longer uses OMAP's sDMA to clear the memory
* Fifomerge has been reverted
* Swap GFX and WB fifos to avoid underflows

When we removed fifomerge support, we also changed dss_ovl_disable so
that it doesn't wait for the hardware to be finished with the overlay.
This may cause a problem when changing the overlay's manager, as
changing the manager is an immediate change. Thus if the overlay is
still being used by the HW when the manager is changed, there may be
glitches on the screen.

This patch adds a wait into dss_ovl_unset_manager, which ensures the
overlays are disabled in the HW.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

set_timings function of DSS's output drivers are not consistent. Some of
them disable the output, set the timings, and re-enable the output. Some
set the timings on the fly, while the output is enabled. And some just
store the given timings, so that they will be taken into use next time
the output is enabled.

We require the DISPC output to be disabled when changing the timings,
and so we can change all the output drivers' set_timings to just store
the given timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP4's GFX overlay has smaller fifo than the rest of the overlays
(including writeback "overlay"). This seems to be the reason for
underflows in some more demanding scenarios.

We can avoid the problems by using the WB fifo for GFX overlay, and vice
versa. WB usage is not supported yet, but when it will, it should
perform just fine with smaller fifo as there are no hard realtime
constraints with WB.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP4+ allows assigning the overlay FIFOs freely, but that is not
supported by omapdss yet. This patch takes a step forward by improving
the fifo management to be more flexible.

dispc.c is changed to keep track of the sizes of each fifo, and also the
overlay using each fifo.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This reverts commit fb011974.

Adding fifo merge feature as an omapdss internal configuration was a
mistake. We cannot hide from the users of omapdss the complexities of
fifo merge.

The previous commit removed fifo merge itself, and this removes the
remaining fifo merge support functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This reverts commit 1d71f42b.

Adding fifo merge feature as an omapdss internal configuration was a
mistake. We cannot hide from the users of omapdss the complexities of
fifo merge.

This commit removes the fifo merge support, which luckily is easily done
as it was handled totally inside apply.c. Note that this is not a 1:1
revert, but some resolving was needed for the dss_ovl_setup_fifo.

The plan is to try fifo merge again later when it is more clear how the
hardware acts in various situations, and how the omapdrm wants to use
fifo merge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dss_mgr_set_timings() can only be called when the output is not active.
This means that most of the code in the function is extra, as there's no
need to write the values to registers, etc, because that will be handled
when the output will be enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dss_mgr_set_lcd_config() can only be called when the output is not
active. This means that most of the code in the function is extra, as
there's no need to write the values to registers, etc, because that will
be handled when the output will be enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Separate sysfs code for managers to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Separate sysfs code for overlays to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use devm_ version instead of the regular gpio_request_one to simplify
the error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Reorganize taal driver to make it easier to integrate device tree code.
Instead of storing the panel's platform data, we'll "parse" the platform
data and store the required information in driver's own data. This way
adding device tree data parsing is simple.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Currently vram.c clears the allocated memory automatically using OMAP
system DMA. In an effort to reduce OMAP dependencies, we'll do the
memory clear with CPU from now on.

The previous patch implemented memory clear in the omapfb driver, and
this patch removes the now obsolete clear functionality from vram.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>

Currently vram.c clears the allocated memory automatically using OMAP
system DMA. In an effort to reduce OMAP dependencies, we'll do the
memory clear with CPU from now on.

This patch implements clearing of the framebuffer in omapfb, using
cfb_fillrect() to do the actual clear.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Remove unnecessary includes from omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>