memslot->userfault_addr is set by the kernel with a mmap executed
from the kernel but the userland can still munmap it and lead to the
below oops after memslot->userfault_addr points to a host virtual
address that has no vma or mapping.

[  327.538306] BUG: unable to handle kernel paging request at fffffffffffffffe
[  327.538407] IP: [<ffffffff811a7b55>] put_page+0x5/0x50
[  327.538474] PGD 1a01067 PUD 1a03067 PMD 0
[  327.538529] Oops: 0000 [#1] SMP
[  327.538574] Modules linked in: macvtap macvlan xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT iptable_filter ip_tables tun bridge stp llc rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache xprtrdma ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp scsi_tgt ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ipmi_devintf iTCO_wdt iTCO_vendor_support intel_powerclamp coretemp dcdbas intel_rapl kvm_intel kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd pcspkr sb_edac edac_core ipmi_si ipmi_msghandler acpi_pad wmi acpi_power_meter lpc_ich mfd_core mei_me
[  327.539488]  mei shpchp nfsd auth_rpcgss nfs_acl lockd grace sunrpc mlx4_ib ib_sa ib_mad ib_core mlx4_en vxlan ib_addr ip_tunnel xfs libcrc32c sd_mod crc_t10dif crct10dif_common crc32c_intel mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm drm ahci i2c_core libahci mlx4_core libata tg3 ptp pps_core megaraid_sas ntb dm_mirror dm_region_hash dm_log dm_mod
[  327.539956] CPU: 3 PID: 3161 Comm: qemu-kvm Not tainted 3.10.0-240.el7.userfault19.4ca4011.x86_64.debug #1
[  327.540045] Hardware name: Dell Inc. PowerEdge R420/0CN7CM, BIOS 2.1.2 01/20/2014
[  327.540115] task: ffff8803280ccf00 ti: ffff880317c58000 task.ti: ffff880317c58000
[  327.540184] RIP: 0010:[<ffffffff811a7b55>]  [<ffffffff811a7b55>] put_page+0x5/0x50
[  327.540261] RSP: 0018:ffff880317c5bcf8  EFLAGS: 00010246
[  327.540313] RAX: 00057ffffffff000 RBX: ffff880616a20000 RCX: 0000000000000000
[  327.540379] RDX: 0000000000002014 RSI: 00057ffffffff000 RDI: fffffffffffffffe
[  327.540445] RBP: ffff880317c5bd10 R08: 0000000000000103 R09: 0000000000000000
[  327.540511] R10: 0000000000000000 R11: 0000000000000000 R12: fffffffffffffffe
[  327.540576] R13: 0000000000000000 R14: ffff880317c5bd70 R15: ffff880317c5bd50
[  327.540643] FS:  00007fd230b7f700(0000) GS:ffff880630800000(0000) knlGS:0000000000000000
[  327.540717] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  327.540771] CR2: fffffffffffffffe CR3: 000000062a2c3000 CR4: 00000000000427e0
[  327.540837] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  327.540904] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  327.540974] Stack:
[  327.541008]  ffffffffa05d6d0c ffff880616a20000 0000000000000000 ffff880317c5bdc0
[  327.541093]  ffffffffa05ddaa2 0000000000000000 00000000002191bf 00000042f3feab2d
[  327.541177]  00000042f3feab2d 0000000000000002 0000000000000001 0321000000000000
[  327.541261] Call Trace:
[  327.541321]  [<ffffffffa05d6d0c>] ? kvm_vcpu_reload_apic_access_page+0x6c/0x80 [kvm]
[  327.543615]  [<ffffffffa05ddaa2>] vcpu_enter_guest+0x3f2/0x10f0 [kvm]
[  327.545918]  [<ffffffffa05e2f10>] kvm_arch_vcpu_ioctl_run+0x2b0/0x5a0 [kvm]
[  327.548211]  [<ffffffffa05e2d02>] ? kvm_arch_vcpu_ioctl_run+0xa2/0x5a0 [kvm]
[  327.550500]  [<ffffffffa05ca845>] kvm_vcpu_ioctl+0x2b5/0x680 [kvm]
[  327.552768]  [<ffffffff810b8d12>] ? creds_are_invalid.part.1+0x12/0x50
[  327.555069]  [<ffffffff810b8d71>] ? creds_are_invalid+0x21/0x30
[  327.557373]  [<ffffffff812d6066>] ? inode_has_perm.isra.49.constprop.65+0x26/0x80
[  327.559663]  [<ffffffff8122d985>] do_vfs_ioctl+0x305/0x530
[  327.561917]  [<ffffffff8122dc51>] SyS_ioctl+0xa1/0xc0
[  327.564185]  [<ffffffff816de829>] system_call_fastpath+0x16/0x1b
[  327.566480] Code: 0b 31 f6 4c 89 e7 e8 4b 7f ff ff 0f 0b e8 24 fd ff ff e9 a9 fd ff ff 66 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 <48> f7 07 00 c0 00 00 55 48 89 e5 75 2a 8b 47 1c 85 c0 74 1e f0
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM may turn a user page to a kernel page when kernel writes a readonly
user page if CR0.WP = 1. This shadow page entry will be reused after
SMAP is enabled so that kernel is allowed to access this user page

Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu
once CR4.SMAP is updated
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

smep_andnot_wp is initialized in kvm_init_shadow_mmu and shadow pages
should not be reused for different values of it.  Thus, it has to be
added to the mask in kvm_mmu_pte_write.
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Current permission check assumes that RSVD bit in PFEC is always zero,
however, it is not true since MMIO #PF will use it to quickly identify
MMIO access

Fix it by clearing the bit if walking guest page table is needed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This fixes a regression introduced in commit 25fedfca, "KVM: PPC:
Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu", which
leads to a user-triggerable oops.

In the case where we try to run a vcore on a physical core that is
not in single-threaded mode, or the vcore has too many threads for
the physical core, we iterate the list of runnable vcpus to make
each one return an EBUSY error to userspace.  Since this involves
taking each vcpu off the runnable_threads list for the vcore, we
need to use list_for_each_entry_safe rather than list_for_each_entry
to traverse the list.  Otherwise the kernel will crash with an oops
message like this:

Unable to handle kernel paging request for data at address 0x000fff88
Faulting instruction address: 0xd00000001e635dc8
Oops: Kernel access of bad area, sig: 11 [#2]
SMP NR_CPUS=1024 NUMA PowerNV
...
CPU: 48 PID: 91256 Comm: qemu-system-ppc Tainted: G      D        3.18.0 #1
task: c00000274e507500 ti: c0000027d1924000 task.ti: c0000027d1924000
NIP: d00000001e635dc8 LR: d00000001e635df8 CTR: c00000000011ba50
REGS: c0000027d19275b0 TRAP: 0300   Tainted: G      D         (3.18.0)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE>  CR: 22002824  XER: 00000000
CFAR: c000000000008468 DAR: 00000000000fff88 DSISR: 40000000 SOFTE: 1
GPR00: d00000001e635df8 c0000027d1927830 d00000001e64c850 0000000000000001
GPR04: 0000000000000001 0000000000000001 0000000000000000 0000000000000000
GPR08: 0000000000200200 0000000000000000 0000000000000000 d00000001e63e588
GPR12: 0000000000002200 c000000007dbc800 c000000fc7800000 000000000000000a
GPR16: fffffffffffffffc c000000fd5439690 c000000fc7801c98 0000000000000001
GPR20: 0000000000000003 c0000027d1927aa8 c000000fd543b348 c000000fd543b350
GPR24: 0000000000000000 c000000fa57f0000 0000000000000030 0000000000000000
GPR28: fffffffffffffff0 c000000fd543b328 00000000000fe468 c000000fd543b300
NIP [d00000001e635dc8] kvmppc_run_core+0x198/0x17c0 [kvm_hv]
LR [d00000001e635df8] kvmppc_run_core+0x1c8/0x17c0 [kvm_hv]
Call Trace:
[c0000027d1927830] [d00000001e635df8] kvmppc_run_core+0x1c8/0x17c0 [kvm_hv] (unreliable)
[c0000027d1927a30] [d00000001e638350] kvmppc_vcpu_run_hv+0x5b0/0xdd0 [kvm_hv]
[c0000027d1927b70] [d00000001e510504] kvmppc_vcpu_run+0x44/0x60 [kvm]
[c0000027d1927ba0] [d00000001e50d4a4] kvm_arch_vcpu_ioctl_run+0x64/0x170 [kvm]
[c0000027d1927be0] [d00000001e504be8] kvm_vcpu_ioctl+0x5e8/0x7a0 [kvm]
[c0000027d1927d40] [c0000000002d6720] do_vfs_ioctl+0x490/0x780
[c0000027d1927de0] [c0000000002d6ae4] SyS_ioctl+0xd4/0xf0
[c0000027d1927e30] [c000000000009358] syscall_exit+0x0/0x98
Instruction dump:
60000000 60420000 387e1b30 38800003 38a00001 38c00000 480087d9 e8410018
ebde1c98 7fbdf040 3bdee368 419e0048 <813e1b20> 939e1b18 2f890001 409effcc
---[ end trace 8cdf50251cca6680 ]---

Fixes: 25fedfcaSigned-off-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull ext4 fixes from Ted Ts'o:
 "Some miscellaneous bug fixes and some final on-disk and ABI changes
  for ext4 encryption which provide better security and performance"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix growing of tiny filesystems
  ext4: move check under lock scope to close a race.
  ext4: fix data corruption caused by unwritten and delayed extents
  ext4 crypto: remove duplicated encryption mode definitions
  ext4 crypto: do not select from EXT4_FS_ENCRYPTION
  ext4 crypto: add padding to filenames before encrypting
  ext4 crypto: simplify and speed up filename encryption

Pull drm fixes from Dave Airlie:
 "One intel fix, one rockchip fix, and a bunch of radeon fixes for some
  regressions from audio rework and vm stability"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915/chv: Implement WaDisableShadowRegForCpd
  drm/radeon: fix userptr return value checking (v2)
  drm/radeon: check new address before removing old one
  drm/radeon: reset BOs address after clearing it.
  drm/radeon: fix lockup when BOs aren't part of the VM on release
  drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
  drm/radeon: adjust pll when audio is not enabled
  drm/radeon: only enable audio streams if the monitor supports it
  drm/radeon: only mark audio as connected if the monitor supports it (v3)
  drm/radeon/audio: don't enable packets until the end
  drm/radeon: drop dce6_dp_enable
  drm/radeon: fix ordering of AVI packet setup
  drm/radeon: Use drm_calloc_ab for CS relocs
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
  drm/i915/chv: Implement WaDisableShadowRegForCpd

one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Pull SCSI fixes from James Bottomley:
 "This is three logical fixes (as 5 patches).

  The 3ware class of drivers were causing an oops with multiqueue by
  tearing down the command mappings after completing the command (where
  the variables in the command used to tear down the mapping were
  no-longer valid).  There's also a fix for the qnap iscsi target which
  was choking on us sending it commands that were too long and a fix for
  the reworked aha1542 allocating GFP_KERNEL under a lock"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: fix command completion race
  3w-xxxx: fix command completion race
  3w-sas: fix command completion race
  aha1542: Allocate memory before taking a lock
  SCSI: add 1024 max sectors black list flag

Pull slave dmaengine fixes from Vinod Koul:
 "Here are the fixes in dmaengine subsystem for rc2:

   - privatecnt fix for slave dma request API by Christopher

   - warn fix for PM ifdef in usb-dmac by Geert

   - fix hardware dependency for xgene by Jean"

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: increment privatecnt when using dma_get_any_slave_channel
  dmaengine: xgene: Set hardware dependency
  dmaengine: usb-dmac: Protect PM-only functions to kill warning

Pull powerpc fixes from Michael Ellerman:
 - build fix for SMP=n in book3s_xics.c
 - fix for Daniel's pci_controller_ops on powernv.
 - revert the TM syscall abort patch for now.
 - CPU affinity fix from Nathan.
 - two EEH fixes from Gavin.
 - fix for CR corruption from Sam.
 - selftest build fix.

* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/powernv: Restore non-volatile CRs after nap
  powerpc/eeh: Delay probing EEH device during hotplug
  powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
  powerpc/pseries: Correct cpu affinity for dlpar added cpus
  selftests/powerpc: Fix the pmu install rule
  Revert "powerpc/tm: Abort syscalls in active transactions"
  powerpc/powernv: Fix early pci_controller_ops loading.
  powerpc/kvm: Fix SMP=n build error in book3s_xics.c

The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.

Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>

fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.

The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.

At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.

When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.

For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.

This problem can be easily reproduced by running the following xfs_io.

xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
          -c "falloc 0 131072" \
          -c "pwrite -S 0xbb 65536 2048" \
          -c "fsync" /mnt/test/fff

echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff

This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d8 and commit f542fb.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull networking fixes from David Miller:

 1) Receive packet length needs to be adjust by 2 on RX to accomodate
    the two padding bytes in altera_tse driver.  From Vlastimil Setka.

 2) If rx frame is dropped due to out of memory in macb driver, we leave
    the receive ring descriptors in an undefined state.  From Punnaiah
    Choudary Kalluri

 3) Some netlink subsystems erroneously signal NLM_F_MULTI.  That is
    only for dumps.  Fix from Nicolas Dichtel.

 4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
    the ipv4_mtu() helper.  From Herbert Xu.

 5) Fix null deref in bridge netfilter, and miscalculated lengths in
    jump/goto nf_tables verdicts.  From Florian Westphal.

 6) Unhash ping sockets properly.

 7) Software implementation of BPF divide did 64/32 rather than 64/64
    bit divide.  The JITs got it right.  Fix from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
  ipv4: Missing sk_nulls_node_init() in ping_unhash().
  net: fec: Fix RGMII-ID mode
  net/mlx4_en: Schedule napi when RX buffers allocation fails
  netxen_nic: use spin_[un]lock_bh around tx_clean_lock
  net/mlx4_core: Fix unaligned accesses
  mlx4_en: Use correct loop cursor in error path.
  cxgb4: Fix MC1 memory offset calculation
  bnx2x: Delay during kdump load
  net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
  net: dsa: Fix scope of eeprom-length property
  net: macb: Fix race condition in driver when Rx frame is dropped
  hv_netvsc: Fix a bug in netvsc_start_xmit()
  altera_tse: Correct rx packet length
  mlx4: Fix tx ring affinity_mask creation
  tipc: fix problem with parallel link synchronization mechanism
  tipc: remove wrong use of NLM_F_MULTI
  bridge/nl: remove wrong use of NLM_F_MULTI
  bridge/mdb: remove wrong use of NLM_F_MULTI
  net: sched: act_connmark: don't zap skb->nfct
  trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
  ...

Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.

This makes it clear that Michael is in charge.  He's good, but having
me watch over his shoulder won't help.

Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull Ceph RBD fix from Sage Weil.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: end I/O the entire obj_request on error

If we don't do that, then the poison value is left in the ->pprev
backlink.

This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed.  Otherwise block layer ends up confused and we
trip on

    rbd_assert(more ^ (which == img_request->obj_request_count));

in rbd_img_obj_callback() due to more being true no matter what.  We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.

A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.

Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

This obscures the length of the filenames, to decrease the amount of
information leakage.  By default, we pad the filenames to the next 4
byte boundaries.  This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway.  Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.

Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.

Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull btrfs fixes from Chris Mason:
 "A few more btrfs fixes.

  These range from corners Filipe found in the new free space cache
  writeback to a grab bag of fixes from the list"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
  Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
  btrfs: unlock i_mutex after attempting to delete subvolume during send
  btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
  btrfs: fix race on ENOMEM in alloc_extent_buffer
  btrfs: handle ENOMEM in btrfs_alloc_tree_block
  Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
  Btrfs: don't check for delalloc_bytes in cache_save_setup
  Btrfs: fix deadlock when starting writeback of bg caches
  Btrfs: fix race between start dirty bg cache writeout and bg deletion

Pull arm64 fixes from Will Deacon:
 "Not too much here, but we've addressed a couple of nasty issues in the
  dma-mapping code as well as adding the halfword and byte variants of
  load_acquire/store_release following on from the CSD locking bug that
  you fixed in the core.

   - fix perf devicetree warnings at probe time

   - fix memory leak in __dma_free()

   - ensure DMA buffers are always zeroed

   - show IRQ trigger in /proc/interrupts (for parity with ARM)

   - implement byte and halfword access for smp_{load_acquire,store_release}"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: perf: Fix the pmu node name in warning message
  arm64: perf: don't warn about missing interrupt-affinity property for PPIs
  arm64: add missing PAGE_ALIGN() to __dma_free()
  arm64: dma-mapping: always clear allocated buffers
  ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
  arm64: add missing data types in smp_load_acquire/smp_store_release

Patches 7cba160a "powernv/cpuidle: Redesign idle states management"
and 77b54e9f "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.

Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.

This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.

The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.

When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.

Fixes: 7cba160a ("powernv/cpuidle: Redesign idle states management")
Fixes: 77b54e9f ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.

Fixes: ff57b454 ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.

The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.

Fixes: 28158cd1 ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.

This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.

Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.

Fixes: 1a8061c4 ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

My patch to add install support for the powerpc selftests had a typo,
leading to the three tests in the pmu directory itself not being
installed.

Fixes: 6faeeea4 ("selftests: Add install support for the powerpc tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull power management and ACPI fixes from Rafael Wysocki:
 "Three regression fixes this time, one for a recent regression in the
  cpuidle core affecting multiple systems, one for an inadvertently
  added duplicate typedef in ACPICA that breaks compilation with GCC 4.5
  and one for an ACPI Smart Battery Subsystem driver regression
  introduced during the 3.18 cycle (stable-candidate).

  Specifics:

   - Fix for a regression in the cpuidle core introduced by one of the
     recent commits in the clockevents_notify() removal series that put
     a call to a function which had to be executed with disabled
     interrupts into a code path running with enabled interrupts (Rafael
     J Wysocki)

   - Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
     of the recent ACPICA tools commits that added a duplicate typedef
     to one of the ACPICA's header files by mistake (Olaf Hering)

   - Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
     driver introduced during the 3.18 development cycle causing the
     smart battery manager to be marked as not present when it should be
     marked as present (Chris Bainbridge)"

* tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: Run tick_broadcast_exit() with disabled interrupts
  ACPI / SBS: Enable battery manager when present
  ACPICA: remove duplicate u8 typedef

Pull sound fixes from Takashi Iwai:
 "One nice fix is Peter's patch to make the old good SB Audigy PCI to
  work with 32bit DMA instead of 31bit.  This allows the MIDI synth
  running on modern machines again.  Along with it, a few fixes for
  emu10k1 have merged.

  In ASoC side, there is one fix in the common code, but it's just
  trivial additions of static inline functions for CONFIG_PM=n.  The
  rest are various device-specific small fixes.

  Last but not least, a few HD-audio fixes are included, as usual, too"

* tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
  ASoC: rt5677: fixed wrong DMIC ref clock
  ALSA: emu10k1: Emu10k2 32 bit DMA mode
  ALSA: emux: Fix mutex deadlock in OSS emulation
  ASoC: Update email-id of Rajeev Kumar
  ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
  ALSA: hda - Fix missing va_end() call in snd_hda_codec_pcm_new()
  ALSA: emux: Fix mutex deadlock at unloading
  ALSA: emu10k1: Fix card shortname string buffer overflow
  ALSA: hda - Add mute-LED mode control to Thinkpad
  ALSA: hda - Fix mute-LED fixed mode
  ALSA: hda - Fix click noise at start on Dell XPS13
  ASoC: rt5645: Add ACPI match ID
  ASoC: rt5677: add register patch for PLL
  ASoC: Intel: fix the makefile for atom code
  ASoC: dapm: Enable autodisable on SOC_DAPM_SINGLE_TLV_AUTODISABLE
  ASoC: add static inline funcs to fix a compiling issue
  ASoC: Intel: sst_byt: remove kfree for memory allocated with devm_kzalloc
  ASoC: samsung: s3c24xx-i2s: Fix return value check in s3c24xx_iis_dev_probe()
  ASoC: tfa9879: Fix return value check in tfa9879_i2c_probe()
  ASoC: fsl_ssi: Fix platform_get_irq() error handling
  ...

RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.

So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.

This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Addresses the following kernel logs seen during boot:

Kernel unaligned access at TPC[100ee150] mlx4_QUERY_HCA+0x80/0x248 [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Fixes: 9e311e77 ("net/mlx4_en: Use affinity hint")
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>