The layer above will free the skb in an error case.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes assignment of the interrupt vectors on the SSB MIPS core.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes the TPS flag handling for the SSB pcicore driver.
This fixes interrupts on some devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When associating to a b-only AP where there is no ERP IE, short preamble
mode is left at previous state (probably also protection mode). In this
case, disable protection and use short preamble mode as specified in
capability field. The same is done if capability field is changed on-the-fly.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes the STA AID setting and actually makes hostapd/mac80211
work properly in presence of power-saving stations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes an hard crash which happened upon driver loading on bcm4303 rev.
2 devices.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables the IWL4965_HT flag (n-band) in Kconfig.
Removed the "depends on n" from Kconfig for config IWL4965_HT
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit bada339b enforces that all
interfaces have a valid MAC address before they are brought up.

ipw2200 does not assign a MAC address to it's radiotap interface, meaning
that the radiotap interface cannot be brought up in 2.6.24.
https://bugs.gentoo.org/show_bug.cgi?id=215714

Fix this by copying the MAC address from the real interface.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After moving lbs_find_best_network_ssid() from scan.c to assoc.c gcc was
able to deduce that new_mode might stay uninitialized.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

a) if you initialize something with le32_to_cpu(...), then |= it
with host-endian and feed to cpu_to_le32(), it's most definitely
*not* __le32.  As sparse would've told you...

b) the whole sequence is |= cpu_to_le32(host-endian constant)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

My previous section fix only turned one section problem into another
section problem.

This patch fixes it for real.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The other if blocks don't redeclare temp, remove the redeclaration in
the final if() block.

drivers/net/phy/marvell.c:214:7: warning: symbol 'temp' shadows an earlier one
drivers/net/phy/marvell.c:160:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

These entries are allocated in vlan_dev_set_egress_priority, 
but are never released and leaks on vlan device removal.

Drop these in vlan's ->uninit callback - after the device is 
brought down and everyone is notified about it is going to
be unregistered.

Found during testing vlan netnsization patchset.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5784 B step and newer chips require the PHY DSPs to be fine-tuned
based on one-time programmable values stored in the chip.  This is
essential to achieve optimal PHY operations especially when using
long cables.  We also need to properly handle the 10Mbit RX bit in the
CPMU_CTRL register during PHY reset.

Update version to 3.89.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Let it update the state of all CPUs. The network stack goes
into pains to feed the current IP addresses in, but it is not very
effective if that is only done for some random CPU instead of all.
So change it to feed bits into all CPUs.  I decided to do that lockless 
because well somewhat random results are ok.

v2: Drop rename so that this patch doesn't depend on x86 maintainers
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Anycast DST entries allocated inside ipv6_dev_ac_inc are leaked when
network device is stopped without removing IPv6 addresses from it. The
bug has been observed in the reality on 2.6.18-rhel5 kernel.

In the above case addrconf_ifdown marks all entries as obsolete and
ip6_del_rt called from __ipv6_dev_ac_dec returns ENOENT. The
referrence is not dropped.

The fix is simple. DST entry should not keep referrence when stored in
the FIB6 tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the other case it will be destroyed when last address will be removed
from lo inside a namespace. This will break IPv6 in several places. The
most obvious one is ip6_dst_ifdown.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

addrconf_ifdown is broken in respect to the usage of how
parameter. This function is called with (event != NETDEV_DOWN) and (2)
on the IPv6 stop.  It the latter case inet6_dev from loopback device
should be destroyed.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ICMP relookup path is only meant to modify behaviour when
appropriate IPsec policies are in place and marked as requiring
relookups.  It is certainly not meant to modify behaviour when
IPsec policies don't exist at all.

However, due to an oversight on the error paths existing behaviour
may in fact change should one of the relookup steps fail.

This patch corrects this by redirecting all errors on relookup
failures to the previous code path.  That is, if the initial
xfrm_lookup let the packet pass, we will stand by that decision
should the relookup fail due to an error.

This should be safe from a security point-of-view because compliant
systems must install a default deny policy so the packet would'nt
have passed in that case.

Many thanks to Julian Anastasov for pointing out this error.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: ohci: fix 2 timers to fire at jiffies + 1s
  USB: Allow initialization of broken keyspan serial adapters.
  USB: fix bug in sg initialization in usbtest
  USB: serial: fix regression in Visor/Palm OS module for kernels >= 2.6.24
  USB: cp2101: Add identifiers for the Telegesys ETRX2USB
  USB: serial: ti_usb_3410_5052: Correct TUSB3410 endpoint requirements.
  USB: another ehci_iaa_watchdog fix

A nasty compile error:

In file included from security/keys/internal.h:16,
                 from security/keys/sysctl.c:14:
include/linux/key-ui.h: In function 'key_permission':
include/linux/key-ui.h:51: error: invalid use of undefined type 'struct task_struct'

apparently the compiler has decided that it needs to know sizeof(task_struct)
so that it can add zero to a task_struct* (which is rather dumb of it).

Getting task_struct in scope in these deeply-nested headers is scary-looking,
so let's just remove the "+ 0".

Cc: David Howells <dhowells@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Markers do not mix well with CONFIG_PREEMPT_RCU because it uses
preempt_disable/enable() and not rcu_read_lock/unlock for minimal
intrusiveness.  We would need call_sched and sched_barrier primitives.

Currently, the modification (connection and disconnection) of probes
from markers requires changes to the data structure done in RCU-style :
a new data structure is created, the pointer is changed atomically, a
quiescent state is reached and then the old data structure is freed.

The quiescent state is reached once all the currently running
preempt_disable regions are done running.  We use the call_rcu mechanism
to execute kfree() after such quiescent state has been reached.
However, the new CONFIG_PREEMPT_RCU version of call_rcu and rcu_barrier
does not guarantee that all preempt_disable code regions have finished,
hence the race.

The "proper" way to do this is to use rcu_read_lock/unlock, but we don't
want to use it to minimize intrusiveness on the traced system.  (we do
not want the marker code to call into much of the OS code, because it
would quickly restrict what can and cannot be instrumented, such as the
scheduler).

The temporary fix, until we get call_rcu_sched and rcu_barrier_sched in
mainline, is to use synchronize_sched before each call_rcu calls, so we
wait for the quiescent state in the system call code path.  It will slow
down batch marker enable/disable, but will make sure the race is gone.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the problem that makedumpfile sometimes fails on x86_64 machine.

This patch adds the symbol "phys_base" to a vmcoreinfo data.  The
vmcoreinfo data has the minimum debugging information only for dump
filtering.  makedumpfile (dump filtering command) gets it to distinguish
unnecessary pages, and makedumpfile creates a small dumpfile.

On x86_64 kernel which compiled with CONFIG_PHYSICAL_START=0x0 and
CONFIG_RELOCATABLE=y, makedumpfile fails like the following:

 # makedumpfile -d31 /proc/vmcore dumpfile
 The kernel version is not supported.
 The created dumpfile may be incomplete.
 _exclude_free_page: Can't get next online node.

 makedumpfile Failed.
 #

The cause is the lack of the symbol "phys_base" in a vmcoreinfo data.
If the symbol "phys_base" does not exist, makedumpfile considers an
x86_64 kernel as non relocatable.  As the result, makedumpfile
misunderstands the physical address where the kernel is loaded, and it
cannot translate a kernel virtual address to physical address correctly.

To fix this problem, this patch adds the symbol "phys_base" to a
vmcoreinfo data.
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add some locks and unlocks to some code paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Unlock two grabbed locks on some paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

NBD does not protect the nbd_device's socket from becoming NULL during
receives.

This closes a race with the NBD_CLEAR_SOCK ioctl (nbd-client -d) setting
the nbd_device's socket to NULL right before NBD calls sock_xmit.
Signed-off-by: Mike Snitzer <snitzer@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch deletes a couple of superfluous word occurrences in the
document Documentation/unaligned-memory-access.txt.

Thanks to Sebastien Dugue for the remark about English usage.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Make dma_alloc_coherent respect gfp flags (__GFP_COMP is one that
matters).
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Strange chars appear on the serial port when a printk and a printf
happens at the same time.  This is caused by the pdc sending chars while
atmel_console_write (called from printk) is executing

Concurent access of uart and console to the same port leads to corrupted
data to be transmitted, so disable tx dma (PDC) while writing to the
console.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I found a problem related to losing data during pdc transmission in
atmel_serial: connect ttyS1 with ttyS2 using a loopback cable, send 30
byte of packet from one to the other and waiting for 30 byte.  On the
other side just read and echo the data received.

We always call atmel_tx_dma() from the tasklet regardless of what interrupt
triggered it.
Signed-off-by: michael <trimarchi@gandalf.sssup.it>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently include/linux/kvm.h is not considered by make headers_install,
because Kbuild cannot handle " unifdef-$(CONFIG_FOO) += foo.h.  This problem
was introduced by

commit fb56dbb3
Author: Avi Kivity <avi@qumranet.com>
Date:   Sun Dec 2 10:50:06 2007 +0200

    KVM: Export include/linux/kvm.h only if $ARCH actually supports KVM

    Currently, make headers_check barfs due to <asm/kvm.h>, which <linux/kvm.h>
    includes, not existing.  Rather than add a zillion <asm/kvm.h>s, export kvm.
    only if the arch actually supports it.
Signed-off-by: Avi Kivity <avi@qumranet.com>

which makes this an 2.6.25 regression.

One way of solving the issue is to enhance Kbuild, but Avi and David conviced
me, that changing headers_install is not the way to go.  This patch changes
the definition for linux/kvm.h to unifdef-y.

If  unifdef-y is used for linux/kvm.h "make headers_check" will fail on all
architectures without asm/kvm.h.  Therefore, this patch also provides
asm/kvm.h on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@qumranet.com>
Cc: Sam Ravnborg <sam@ravnborg.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ).  The timer would then fire at time (0 <= T <
HZ).

Fix them to use round_jiffies(jiffies + HZ);
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fixes the keyspan driver after the addition of additional
checking of driver requirements introduced in usb-serial.c
commit 063a2da8.  The initialization
of the keyspan usb_serial_driver structs were not initializing the
num_interrupt_out field and the additional checking was rejecting
the end point so the driver wouldn't finish initializing.

This commit initializes the fields to NUM_DONT_CARE.
It works for the keyspan USA-49WG and doesn't break the USA-19HS
which are the two keyspan devices I have to test with.
Signed-off-by: Clark Rawlins <clark.rawlins@escient.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1062) fixes a bug in the scatter-gather initialization
code in the usbtest driver.  When the sg-helper conversion was
performed, it wasn't done correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fixes a bug/inconsistency revealed by the additional sanity checking in
   commit 063a2da8
introduced in the original 2.6.24 branch.

The Handspring Visor / PalmOS 4 device structure defines .num_bulk_out=2
but the usb-serial probe returns num_bulk_out=3, triggering the check in
the above commit and forcing a bail out when the device (a Garmin iQue in
my case) attempts to connect.  The patch bumps the expected number of
endpoints to 3.

FWIW, this patch will probably solve the following kernel bug report for
Treo users (identical symptoms, different model PalmOS units):
  <http://bugzilla.kernel.org/show_bug.cgi?id=10118>
Signed-off-by: Brad Sawatzky <brad+kernel@swatter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the Telegesys ETRX2USB which
works fine with the cp2101 driver.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Tested-by: Xavier Carcelle <xavier.carcelle@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The changes introduced in commit
063a2da8 changed the semantics of the
num_interrupt_in, num_interrupt_out, num_bulk_in and num_bulk_out
entries of the usb_serial_driver struct to be the number of endpoints
the device has when probed.

This patch changes the ti_1port_device usb_serial_driver struct to
reflect this change.  The single port devices only have 1
bulk_out endpoint in their initial configuration, and so this patch
changes the number of other types to NUM_DONT_CARE.

The same change probably needs doing to the ti_2port_device struct,
but I don't have a two port device at hand.
Signed-off-by: Robert Spanton <rspanton@zepler.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>