On CPU hotplug the steal time accounting can keep a stale rq->prev_steal_time
value over CPU down and up. So after the CPU comes up again the delta
calculation in steal_account_process_tick() wreckages itself due to the
unsigned math:

	 u64 steal = paravirt_steal_clock(smp_processor_id());

	 steal -= this_rq()->prev_steal_time;

So if steal is smaller than rq->prev_steal_time we end up with an insane large
value which then gets added to rq->prev_steal_time, resulting in a permanent
wreckage of the accounting. As a consequence the per CPU stats in /proc/stat
become stale.

Nice trick to tell the world how idle the system is (100%) while the CPU is
100% busy running tasks. Though we prefer realistic numbers.

None of the accounting values which use a previous value to account for
fractions is reset at CPU hotplug time. update_rq_clock_task() has a sanity
check for prev_irq_time and prev_steal_time_rq, but that sanity check solely
deals with clock warps and limits the /proc/stat visible wreckage. The
prev_time values are still wrong.

Solution is simple: Reset rq->prev_*_time when the CPU is plugged in again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: commit 095c0aa8 "sched: adjust scheduler cpu power for stolen time"
Fixes: commit aa483808 "sched: Remove irq time from available CPU power"
Fixes: commit e6e6685a "KVM guest: Steal time accounting"
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1603041539490.3686@nanosSigned-off-by: Ingo Molnar <mingo@kernel.org>

Steven noticed that occasionally a sched_yield() call would not result
in a wait for the next period edge as expected.

It turns out that when we call update_curr_dl() and end up with
delta_exec <= 0, we will bail early and fail to throttle.

Further inspection of the yield code revealed that yield_task_dl()
clearing dl.runtime is wrong too, it will not account the last bit of
runtime which could result in dl.runtime < 0, which in turn means that
replenish would gift us with too much runtime.

Fix both issues by not relying on the dl.runtime value for yield.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Clark Williams <williams@redhat.com>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160223122822.GP6357@twins.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>

When a cgroup's CPU runqueue is destroyed, it should remove its
remaining load accounting from its parent cgroup.

The current site for doing so it unsuited because its far too late and
unordered against other cgroup removal (->css_free() will be, but we're also
in an RCU callback).

Put it in the ->css_offline() callback, which is the start of cgroup
destruction, right after the group has been made unavailable to
userspace. The ->css_offline() callbacks are called in hierarchical order
after the following v4.4 commit:

  aa226ff4 ("cgroup: make sure a parent css isn't offlined before its children")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160121212416.GL6357@twins.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull perf fixes from Thomas Gleixner:
 "A rather largish series of 12 patches addressing a maze of race
  conditions in the perf core code from Peter Zijlstra"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Robustify task_function_call()
  perf: Fix scaling vs. perf_install_in_context()
  perf: Fix scaling vs. perf_event_enable()
  perf: Fix scaling vs. perf_event_enable_on_exec()
  perf: Fix ctx time tracking by introducing EVENT_TIME
  perf: Cure event->pending_disable race
  perf: Fix race between event install and jump_labels
  perf: Fix cloning
  perf: Only update context time when active
  perf: Allow perf_release() with !event->ctx
  perf: Do not double free
  perf: Close install vs. exit race

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - Hopefully the last ASM CLAC fixups

   - A fix for the Quark family related to the IMR lock which makes
     kexec work again

   - A off-by-one fix in the MPX code.  Ironic, isn't it?

   - A fix for X86_PAE which addresses once more an unsigned long vs
     phys_addr_t hickup"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mpx: Fix off-by-one comparison with nr_registers
  x86/mm: Fix slow_virt_to_phys() for X86_PAE again
  x86/entry/compat: Add missing CLAC to entry_INT80_32
  x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32
  x86/platform/intel/quark: Change the kernel's IMR lock bit to false

Pull scheduler fixlet from Thomas Gleixner:
 "A trivial printk typo fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix trivial typo in printk() message

Pull irq fixes from Thomas Gleixner:
 "Four small fixes for irqchip drivers:

   - Add missing low level irq handler initialization on mxs, so
     interrupts can acutally be delivered

   - Add a missing barrier to the GIC driver

   - Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
     and a cache flush beyond the actual region"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
  irqchip/mxs: Add missing set_handle_irq()
  irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
  irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1

Pull staging/android fix from Greg KH:
 "Here is one patch, for the android binder driver, to resolve a
  reported problem.  Turns out it has been around for a while (since
  3.15), so it is good to finally get it resolved.

  It has been in linux-next for a while with no reported issues"

* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE

Pull USB fixes from Greg KH:
 "Here are a few USB fixes for 4.5-rc6

  They fix a reported bug for some USB 3 devices by reverting the recent
  patch, a MAINTAINERS change for some drivers, some new device ids, and
  of course, the usual bunch of USB gadget driver fixes.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  MAINTAINERS: drop OMAP USB and MUSB maintainership
  usb: musb: fix DMA for host mode
  usb: phy: msm: Trigger USB state detection work in DRD mode
  usb: gadget: net2280: fix endpoint max packet for super speed connections
  usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
  usb: gadget: remove driver from pending list on probe error
  Revert "usb: hub: do not clear BOS field during reset device"
  usb: chipidea: fix return value check in ci_hdrc_pci_probe()
  usb: chipidea: error on overflow for port_test_write
  USB: option: add "4G LTE usb-modem U901"
  USB: cp210x: add IDs for GE B650V3 and B850V3 boards
  USB: option: add support for SIM7100E
  usb: musb: Fix DMA desired mode for Mentor DMA engine
  usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
  usb: dwc2: USB_DWC2 should depend on HAS_DMA
  usb: dwc2: host: fix the data toggle error in full speed descriptor dma
  usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
  usb: dwc3: Fix assignment of EP transfer resources
  usb: dwc2: Add extra delay when forcing dr_mode

Pull vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  do_last(): ELOOP failure exit should be done after leaving RCU mode
  should_follow_link(): validate ->d_seq after having decided to follow
  namei: ->d_inode of a pinned dentry is stable only for positives
  do_last(): don't let a bogus return value from ->open() et.al. to confuse us
  fs: return -EOPNOTSUPP if clone is not supported
  hpfs: don't truncate the file when delete fails

Pull ARM SoC fixes from Olof Johansson:
 "We didn't have a batch last week, so this one is slightly larger.

  None of them are scary though, a handful of fixes for small DT pieces,
  replacing properties with newer conventions.

  Highlights:
   - N900 fix for setting system revision
   - onenand init fix to avoid filesystem corruption
   - Clock fix for audio on Beaglebone-x15
   - Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)

  + misc smaller stuff"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Extend info, add wiki and ml for meson arch
  MAINTAINERS: alpine: add a new maintainer and update the entry
  ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
  ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
  Revert "regulator: tps65217: remove tps65217.dtsi file"
  ARM: shmobile: Remove shmobile_boot_arg
  ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss
  ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
  ARM: shmobile: Move shmobile_scu_base from .text to .bss
  ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
  ARM: OMAP2+: Improve omap_device error for driver writers
  ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
  ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
  ARM: OMAP2+: Set system_rev from ATAGS for n900
  ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
  ARM: dts: kirkwood: use unique machine name for ds112
  ARM: dts: imx6: remove bogus interrupt-parent from CAAM node

... or we risk seeing a bogus value of d_is_symlink() there.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... otherwise d_is_symlink() above might have nothing to do with
the inode value we've got.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

both do_last() and walk_component() risk picking a NULL inode out
of dentry about to become positive, *then* checking its flags and
seeing that it's not negative anymore and using (already stale by
then) value they'd fetched earlier.  Usually ends up oopsing soon
after that...

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... into returning a positive to path_openat(), which would interpret that
as "symlink had been encountered" and proceed to corrupt memory, etc.
It can only happen due to a bug in some ->open() instance or in some LSM
hook, etc., so we report any such event *and* make sure it doesn't trick
us into further unpleasantness.

Cc: stable@vger.kernel.org # v3.6+, at least
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

-EBADF is a rather confusing error if an operations is not supported,
and nfsd gets rather upset about it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The delete opration can allocate additional space on the HPFS filesystem
due to btree split. The HPFS driver checks in advance if there is
available space, so that it won't corrupt the btree if we run out of space
during splitting.

If there is not enough available space, the HPFS driver attempted to
truncate the file, but this results in a deadlock since the commit
7dd29d8d ("HPFS: Introduce a global mutex
and lock it on every callback from VFS").

This patch removes the code that tries to truncate the file and -ENOSPC is
returned instead. If the user hits -ENOSPC on delete, he should try to
delete other files (that are stored in a leaf btree node), so that the
delete operation will make some space for deleting the file stored in
non-leaf btree node.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org	# 2.6.39+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge fixes from Andrew Morton:
 "10 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  dax: move writeback calls into the filesystems
  dax: give DAX clearing code correct bdev
  ext4: online defrag not supported with DAX
  ext2, ext4: only set S_DAX for regular inodes
  block: disable block device DAX by default
  ocfs2: unlock inode if deleting inode from orphan fails
  mm: ASLR: use get_random_long()
  drivers: char: random: add get_random_long()
  mm: numa: quickly fail allocations for NUMA balancing on full nodes
  mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED

Pull ext2/4 DAX fix from Ted Ts'o:
 "This fixes a file system corruption bug with DAX"

* tag 'tags/ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext2, ext4: fix issue with missing journal entry in ext4_dax_mkwrite()

Pull PCI fixes from Bjorn Helgaas:
 "Enumeration:
    Revert x86 pcibios_alloc_irq() to fix regression (Bjorn Helgaas)

  Marvell MVEBU host bridge driver:
    Restrict build to 32-bit ARM (Thierry Reding)"

* tag 'pci-v4.5-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: mvebu: Restrict build to 32-bit ARM
  Revert "PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()"
  Revert "PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed"
  Revert "x86/PCI: Don't alloc pcibios-irq when MSI is enabled"

As it is currently written ext4_dax_mkwrite() assumes that the call into
__dax_mkwrite() will not have to do a block allocation so it doesn't create
a journal entry.  For a read that creates a zero page to cover a hole
followed by a write that actually allocates storage this is incorrect.  The
ext4_dax_mkwrite() -> __dax_mkwrite() -> __dax_fault() path calls
get_blocks() to allocate storage.

Fix this by having the ->page_mkwrite fault handler call ext4_dax_fault()
as this function already has all the logic needed to allocate a journal
entry and call __dax_fault().

Also update the ext2 fault handlers in this same way to remove duplicate
code and keep the logic between ext2 and ext4 the same.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull clk fix from Stephen Boyd:
 "One small fix to keep OMAP platforms working across a suspend/resume
  cycle"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: ti: omap3+: dpll: use non-locking version of clk_get_rate

Previously calls to dax_writeback_mapping_range() for all DAX filesystems
(ext2, ext4 & xfs) were centralized in filemap_write_and_wait_range().

dax_writeback_mapping_range() needs a struct block_device, and it used
to get that from inode->i_sb->s_bdev.  This is correct for normal inodes
mounted on ext2, ext4 and XFS filesystems, but is incorrect for DAX raw
block devices and for XFS real-time files.

Instead, call dax_writeback_mapping_range() directly from the filesystem
->writepages function so that it can supply us with a valid block
device.  This also fixes DAX code to properly flush caches in response
to sync(2).
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dax_clear_blocks() needs a valid struct block_device and previously it
was using inode->i_sb->s_bdev in all cases.  This is correct for normal
inodes on mounted ext2, ext4 and XFS filesystems, but is incorrect for
DAX raw block devices and for XFS real-time devices.

Instead, rename dax_clear_blocks() to dax_clear_sectors(), and change
its arguments to take a bdev and a sector instead of an inode and a
block.  This better reflects what the function does, and it allows the
filesystem and raw block device code to pass in an appropriate struct
block_device.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Online defrag operations for ext4 are hard coded to use the page cache.
See ext4_ioctl() -> ext4_move_extents() -> move_extent_per_page()

When combined with DAX I/O, which circumvents the page cache, this can
result in data corruption.  This was observed with xfstests ext4/307 and
ext4/308.

Fix this by only allowing online defrag for non-DAX files.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When S_DAX is set on an inode we assume that if there are pages attached
to the mapping (mapping->nrpages != 0), those pages are clean zero pages
that were used to service reads from holes.  Any dirty data associated
with the inode should be in the form of DAX exceptional entries
(mapping->nrexceptional) that is written back via
dax_writeback_mapping_range().

With the current code, though, this isn't always true.  For example,
ext2 and ext4 directory inodes can have S_DAX set, but have their dirty
data stored as dirty page cache entries.  For these types of inodes,
having S_DAX set doesn't really make sense since their I/O doesn't
actually happen through the DAX code path.

Instead, only allow S_DAX to be set for regular inodes for ext2 and
ext4.  This allows us to have strict DAX vs non-DAX paths in the
writeback code.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recent *sync enabling discovered that we are inserting into the
block_device pagecache counter to the expectations of the dirty data
tracking for dax mappings.  This can lead to data corruption.

We want to support DAX for block devices eventually, but it requires
wider changes to properly manage the pagecache.

   dump_stack+0x85/0xc2
   dax_writeback_mapping_range+0x60/0xe0
   blkdev_writepages+0x3f/0x50
   do_writepages+0x21/0x30
   __filemap_fdatawrite_range+0xc6/0x100
   filemap_write_and_wait+0x4a/0xa0
   set_blocksize+0x70/0xd0
   sb_set_blocksize+0x1d/0x50
   ext4_fill_super+0x75b/0x3360
   mount_bdev+0x180/0x1b0
   ext4_mount+0x15/0x20
   mount_fs+0x38/0x170

Mark the support broken so its disabled by default, but otherwise still
available for testing.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When doing append direct io cleanup, if deleting inode fails, it goes
out without unlocking inode, which will cause the inode deadlock.

This issue was introduced by commit cf1776a9 ("ocfs2: fix a tiny
race when truncate dio orohaned entry").
Signed-off-by: Guozhonghua <guozhonghua@h3c.com>
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: <stable@vger.kernel.org>	[4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Replace calls to get_random_int() followed by a cast to (unsigned long)
with calls to get_random_long().  Also address shifting bug which, in
case of x86 removed entropy mask for mmap_rnd_bits values > 31 bits.
Signed-off-by: Daniel Cashman <dcashman@android.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Kralevich <nnk@google.com>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit d07e2259 ("mm: mmap: add new /proc tunable for mmap_base
ASLR") added the ability to choose from a range of values to use for
entropy count in generating the random offset to the mmap_base address.

The maximum value on this range was set to 32 bits for 64-bit x86
systems, but this value could be increased further, requiring more than
the 32 bits of randomness provided by get_random_int(), as is already
possible for arm64.  Add a new function: get_random_long() which more
naturally fits with the mmap usage of get_random_int() but operates
exactly the same as get_random_int().

Also, fix the shifting constant in mmap_rnd() to be an unsigned long so
that values greater than 31 bits generate an appropriate mask without
overflow.  This is especially important on x86, as its shift instruction
uses a 5-bit mask for the shift operand, which meant that any value for
mmap_rnd_bits over 31 acts as a no-op and effectively disables mmap_base
randomization.

Finally, replace calls to get_random_int() with get_random_long() where
appropriate.

This patch (of 2):

Add get_random_long().
Signed-off-by: Daniel Cashman <dcashman@android.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Kralevich <nnk@google.com>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 4167e9b2 ("mm: remove GFP_THISNODE") removed the GFP_THISNODE
flag combination due to confusing semantics.  It noted that
alloc_misplaced_dst_page() was one such user after changes made by
commit e97ca8e5 ("mm: fix GFP_THISNODE callers and clarify").

Unfortunately when GFP_THISNODE was removed, users of
alloc_misplaced_dst_page() started waking kswapd and entering direct
reclaim because the wrong GFP flags are cleared.  The consequence is
that workloads that used to fit into memory now get reclaimed which is
addressed by this patch.

The problem can be demonstrated with "mutilate" that exercises memcached
which is software dedicated to memory object caching.  The configuration
uses 80% of memory and is run 3 times for varying numbers of clients.
The results on a 4-socket NUMA box are

mutilate
                            4.4.0                 4.4.0
                          vanilla           numaswap-v1
Hmean    1      8394.71 (  0.00%)     8395.32 (  0.01%)
Hmean    4     30024.62 (  0.00%)    34513.54 ( 14.95%)
Hmean    7     32821.08 (  0.00%)    70542.96 (114.93%)
Hmean    12    55229.67 (  0.00%)    93866.34 ( 69.96%)
Hmean    21    39438.96 (  0.00%)    85749.21 (117.42%)
Hmean    30    37796.10 (  0.00%)    50231.49 ( 32.90%)
Hmean    47    18070.91 (  0.00%)    38530.13 (113.22%)

The metric is queries/second with the more the better.  The results are
way outside of the noise and the reason for the improvement is obvious
from some of the vmstats

                                 4.4.0       4.4.0
                               vanillanumaswap-v1r1
Minor Faults                1929399272  2146148218
Major Faults                  19746529        3567
Swap Ins                      57307366        9913
Swap Outs                     50623229       17094
Allocation stalls                35909         443
DMA allocs                           0           0
DMA32 allocs                  72976349   170567396
Normal allocs               5306640898  5310651252
Movable allocs                       0           0
Direct pages scanned         404130893      799577
Kswapd pages scanned         160230174           0
Kswapd pages reclaimed        55928786           0
Direct pages reclaimed         1843936       41921
Page writes file                  2391           0
Page writes anon              50623229       17094

The vanilla kernel is swapping like crazy with large amounts of direct
reclaim and kswapd activity.  The figures are aggregate but it's known
that the bad activity is throughout the entire test.

Note that simple streaming anon/file memory consumers also see this
problem but it's not as obvious.  In those cases, kswapd is awake when
it should not be.

As there are at least two reclaim-related bugs out there, it's worth
spelling out the user-visible impact.  This patch only addresses bugs
related to excessive reclaim on NUMA hardware when the working set is
larger than a NUMA node.  There is a bug related to high kswapd CPU
usage but the reports are against laptops and other UMA hardware and is
not addressed by this patch.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>	[4.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pmd_trans_unstable()/pmd_none_or_trans_huge_or_clear_bad() were
introduced to locklessy (but atomically) detect when a pmd is a regular
(stable) pmd or when the pmd is unstable and can infinitely transition
from pmd_none() and pmd_trans_huge() from under us, while only holding
the mmap_sem for reading (for writing not).

While holding the mmap_sem only for reading, MADV_DONTNEED can run from
under us and so before we can assume the pmd to be a regular stable pmd
we need to compare it against pmd_none() and pmd_trans_huge() in an
atomic way, with pmd_trans_unstable().  The old pmd_trans_huge() left a
tiny window for a race.

Useful applications are unlikely to notice the difference as doing
MADV_DONTNEED concurrently with a page fault would lead to undefined
behavior.

[akpm@linux-foundation.org: tidy up comment grammar/layout]
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This driver uses PCI glue that is only available on 32-bit ARM.  This used
to work fine as long as ARCH_MVEBU and ARCH_DOVE were exclusively 32-bit,
but there's a patch in the pipe to make ARCH_MVEBU also available on 64-bit
ARM.

[bhelgaas: changelog; patch is coming but not merged yet]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

991de2e5 ("PCI, x86: Implement pcibios_alloc_irq() and
pcibios_free_irq()") appeared in v4.3 and helps support IOAPIC hotplug.

Олег reported that the Elcus-1553 TA1-PCI driver worked in v4.2 but not
v4.3 and bisected it to 991de2e5.  Sunjin reported that the RocketRAID
272x driver worked in v4.2 but not v4.3.  In both cases booting with
"pci=routirq" is a workaround.

I think the problem is that after 991de2e5, we no longer call
pcibios_enable_irq() for upstream bridges.  Prior to 991de2e5, when a
driver called pci_enable_device(), we recursively called
pcibios_enable_irq() for upstream bridges via pci_enable_bridge().

After 991de2e5, we call pcibios_enable_irq() from pci_device_probe()
instead of the pci_enable_device() path, which does *not* call
pcibios_enable_irq() for upstream bridges.

Revert 991de2e5 to fix these driver regressions.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211
Fixes: 991de2e5 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()")
Reported-and-tested-by: Олег Мороз <oleg.moroz@mcc.vniiem.ru>
Reported-by: Sunjin Yang <fan4326@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
CC: Jiang Liu <jiang.liu@linux.intel.com>

In the unlikely event that regno == nr_registers then we get an array
overrun on regoff because the invalid register check is currently
off-by-one. Fix this with a check that regno is >= nr_registers instead.

Detected with static analysis using CoverityScan.

Fixes: fcc7ffd6 "x86, mpx: Decode MPX instruction to get bound violation information"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1456512931-3388-1-git-send-email-colin.king@canonical.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull Ceph fixes from Sage Weil:
 "There are two small messenger bug fixes and a log spam regression fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: don't spam dmesg with stray reply warnings
  libceph: use the right footer size when skipping a message
  libceph: don't bail early from try_read() when skipping a message

Pull sound fixes from Takashi Iwai:
 "Things got calmed down for rc6, as it seems, and we have only a few
  HD-audio fixes at this time: a fix for Skylake codec probe errors, a
  fix for missing interrupt handling, and a few Dell and HP quirks"

* tag 'sound-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Loop interrupt handling until really cleared
  ALSA: hda - Fix headset support and noise on HP EliteBook 755 G2
  ALSA: hda - Fixup speaker pass-through control for nid 0x14 on ALC225
  ALSA: hda - Fixing background noise on Dell Inspiron 3162
  ALSA: hda - Apply clock gate workaround to Skylake, too

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are two reverts of recent PCI-related ACPI core changes (one of
  which caused some systems to crash on boot and the other was a cleanup
  on top of it) and a devfreq fix for Tegra.

  Specifics:

   - Revert an ACPI core change related to IRQ management in PCI that
     introduced code relying on the use of kmalloc() which turned out to
     also run during early init when that's not available yet and caused
     some systems to crash on boot for this reason along with a cleanup
     on top of it (Rafael Wysocki).

   - Prevent devfreq from flooding the kernel log with useless messages
     on Tegra (which started to happen after some recent changes in the
     devfreq core) by fixing the driver to follow the documentation and
     the core's expectations in its ->target callback (Tomeu Vizoso)"

* tag 'pm+acpi-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPI, PCI, irq: remove interrupt count restriction"
  Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
  PM / devfreq: tegra: Set freq in rate callback

* pm-devfreq:
  PM / devfreq: tegra: Set freq in rate callback

* acpi-pci:
  Revert "ACPI, PCI, irq: remove interrupt count restriction"
  Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"