This pin definition had been added after the initial patch to use
symbolic pin names in DTS files.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Update the Ka-Ro TX28 DTS file.

- add Copyright header
- use label references for better readability
- sort the entries alphabetically
- add some aliases used by U-Boot to modify the DT data
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).

As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.

	31     23      15      7        0
	| 0xff | shift | width | select |

Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Convert mx23/mx28 dts filed to use the pinctrl header files.

NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts

According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX

I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Remove the list of possible pin configurations from the documentation
file and create header files containing those definitions.
This eliminates the need for error-prone manual lookup of those values
in the documentation and guarantees consistency between the human
readable representation of the pad function in the .dts file and the
actual binary value used in DT.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Provide 'lradc-touchscreen-wires' property to the LRADC driver, so that
touchscreen can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

On imx6qdl-sabresd the SDHC2 and SDHC3 are 8 bit-wide, so pass the bus-width
property to reflect that.

Otherwise the mmc driver will operate with the default bus-width value of 4.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add spi aliases.

While at it, keep the aliases entries sorted.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable USB function for OTG 1 and OTG 2 at mx6sololite evk.
Besides, fix the wrong interrupt number for OTG2 and host 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add iomuxc gpr device node for imx6sl.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch enables DSPI0 and at26df081a flash device for Vybrid VF610
TOWER board.
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add Freescale DSPI node into vf610 dts.
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

imx6q-sabrelite board can be connected to a 1024x768 Hannstar LVDS panel.

Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Put the nodes in alphabetical order so that further node additions can be better
organized.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Trying to use the usb otg port on mx53qsb results in the following error:

$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 52:0f:8a:1e:aa:09
usb0: MAC de:f3:70:d8:6c:62
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready

(Connect the USB cable)

$ ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11

USB otg port goes to connector J3 (mini USB) and also to the USB combo (J2).

As mx53qsb does not provide a USB ID pin, pass the dr_mode as 'peripheral' so
that we can have usb device working.

Tested via g_ether.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Testing g_ether results in the following:

[    1.648022] using random self ethernet address
[    1.652778] using random host ethernet address
[    1.660504] usb0: HOST MAC c6:28:6a:81:dc:ff
[    1.666360] usb0: MAC 7e:81:54:16:c0:c6
[    1.670504] using random self ethernet address
[    1.675842] using random host ethernet address
[    1.682655] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    1.689332] g_ether gadget: g_ether ready
[    3.328974] irq 237: nobody cared (try booting with the "irqpoll" option)
[    3.335831] CPU: 0 PID: 1 Comm: swapper Not tainted 3.11.0-rc6-next-20130819 #1035
[    3.343500] [<c0014258>] (unwind_backtrace+0x0/0xf0) from [<c0011b20>] (show_stack+0x10/0x14)
[    3.352098] [<c0011b20>] (show_stack+0x10/0x14) from [<c006af4c>] (__report_bad_irq+0x20/0xc0)
[    3.360763] [<c006af4c>] (__report_bad_irq+0x20/0xc0) from [<c006b3f4>] (note_interrupt+0x1d4/0x234)
[    3.369943] [<c006b3f4>] (note_interrupt+0x1d4/0x234) from [<c0069754>] (handle_irq_event_percpu+0xc4/0x268)
[    3.379815] [<c0069754>] (handle_irq_event_percpu+0xc4/0x268) from [<c0069934>] (handle_irq_event+0x3c/0x5c)
[    3.389686] [<c0069934>] (handle_irq_event+0x3c/0x5c) from [<c006bb78>] (handle_level_irq+0x8c/0xe8)
[    3.398865] [<c006bb78>] (handle_level_irq+0x8c/0xe8) from [<c0068ff0>] (generic_handle_irq+0x20/0x30)
[    3.408213] [<c0068ff0>] (generic_handle_irq+0x20/0x30) from [<c000fc9c>] (handle_IRQ+0x30/0x84)
[    3.417040] [<c000fc9c>] (handle_IRQ+0x30/0x84) from [<c0012564>] (__irq_svc+0x44/0x54)
[    3.425094] [<c0012564>] (__irq_svc+0x44/0x54) from [<c0020244>] (__do_softirq+0x90/0x268)
[    3.433400] [<c0020244>] (__do_softirq+0x90/0x268) from [<c00207d4>] (irq_exit+0x9c/0xd8)
[    3.441619] [<c00207d4>] (irq_exit+0x9c/0xd8) from [<c000fca0>] (handle_IRQ+0x34/0x84)
[    3.449577] [<c000fca0>] (handle_IRQ+0x34/0x84) from [<c0012564>] (__irq_svc+0x44/0x54)
[    3.457629] [<c0012564>] (__irq_svc+0x44/0x54) from [<c04602b0>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[    3.467164] [<c04602b0>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c0348298>] (input_register_handler+0x98/0xb4)
[    3.477835] [<c0348298>] (input_register_handler+0x98/0xb4) from [<c064bc10>] (mousedev_init+0x30/0x60)
[    3.487275] [<c064bc10>] (mousedev_init+0x30/0x60) from [<c00088ac>] (do_one_initcall+0xe8/0x154)
[    3.496198] [<c00088ac>] (do_one_initcall+0xe8/0x154) from [<c062aabc>] (kernel_init_freeable+0xf0/0x1b4)
[    3.505810] [<c062aabc>] (kernel_init_freeable+0xf0/0x1b4) from [<c0456550>] (kernel_init+0x8/0xe4)
[    3.514899] [<c0456550>] (kernel_init+0x8/0xe4) from [<c000ee60>] (ret_from_fork+0x14/0x34)
[    3.523263] handlers:
[    3.525578] [<c0339d14>] ci_irq
[    3.528757] Disabling IRQ #237

Provide the USB0_ID pin in the usb0 node, so that g_ether can operate
correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Tested via g_ether:

$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 42:b5:26:a9:48:21
usb0: MAC 36:a6:85:9b:9e:13
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
$ g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
$ ifconfig usb0 10.0.0.2

Then on the PC host side:

~$ sudo ifconfig usb0 10.0.0.1
~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_req=1 ttl=64 time=1.26 ms
64 bytes from 10.0.0.2: icmp_req=2 ttl=64 time=0.280 ms
64 bytes from 10.0.0.2: icmp_req=3 ttl=64 time=0.297 ms
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds the missing W1 (onewire) devicetree node for i.MX51 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds the missing IRAM devicetree node for i.MX51 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

RTS/CTS pins can be used for different purposes, so create separate
definitions for these pins.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

There is no imx6sl specific sdma firmware.  Instead, imx6sl reuses
imx6q sdma firmware.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Pull staging fixes from Greg KH:
 "Here are a number of small staging tree and iio driver fixes.  Nothing
  major, just lots of little things"

* tag 'staging-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
  iio:buffer_cb: Add missing iio_buffer_init()
  iio: Prevent race between IIO chardev opening and IIO device free
  iio: fix: Keep a reference to the IIO device for open file descriptors
  iio: Stop sampling when the device is removed
  iio: Fix crash when scan_bytes is computed with active_scan_mask == NULL
  iio: Fix mcp4725 dev-to-indio_dev conversion in suspend/resume
  iio: Fix bma180 dev-to-indio_dev conversion in suspend/resume
  iio: Fix tmp006 dev-to-indio_dev conversion in suspend/resume
  iio: iio_device_add_event_sysfs() bugfix
  staging: iio: ade7854-spi: Fix return value
  staging:iio:hmc5843: Fix measurement conversion
  iio: isl29018: Fix uninitialized value
  staging:iio:dummy fix kfifo_buf kconfig dependency issue if kfifo modular and buffer enabled for built in dummy driver.
  iio: at91: fix adc_clk overflow
  staging: line6: add bounds check in snd_toneport_source_put()
  Staging: comedi: Fix dependencies for drivers misclassified as PCI
  staging: r8188eu: Adjust RX gain
  staging: r8188eu: Fix smatch warning in core/rtw_ieee80211.
  staging: r8188eu: Fix smatch error in core/rtw_mlme_ext.c
  staging: r8188eu: Fix Smatch off-by-one warning in hal/rtl8188e_hal_init.c
  ...

Pull USB fixes from Greg KH:
 "Here are a number of small USB fixes for 3.12-rc2.

  One is a revert of a EHCI change that isn't quite ready for 3.12.
  Others are minor things, gadget fixes, Kconfig fixes, and some quirks
  and documentation updates.

  All have been in linux-next for a bit"

* tag 'usb-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: pl2303: distinguish between original and cloned HX chips
  USB: Faraday fotg210: fix email addresses
  USB: fix typo in usb serial simple driver Kconfig
  Revert "USB: EHCI: support running URB giveback in tasklet context"
  usb: s3c-hsotg: do not disconnect gadget when receiving ErlySusp intr
  usb: s3c-hsotg: fix unregistration function
  usb: gadget: f_mass_storage: reset endpoint driver data when disabled
  usb: host: fsl-mph-dr-of: Staticize local symbols
  usb: gadget: f_eem: Staticize eem_alloc
  usb: gadget: f_ecm: Staticize ecm_alloc
  usb: phy: omap-usb3: Fix return value
  usb: dwc3: gadget: avoid memory leak when failing to allocate all eps
  usb: dwc3: remove extcon dependency
  usb: gadget: add '__ref' for rndis_config_register() and cdc_config_register()
  usb: dwc3: pci: add support for BayTrail
  usb: gadget: cdc2: fix conversion to new interface of f_ecm
  usb: gadget: fix a bug and a WARN_ON in dummy-hcd
  usb: gadget: mv_u3d_core: fix violation of locking discipline in mv_u3d_ep_disable()

Pull drm fixes from Dave Airlie:
 - some small fixes for msm and exynos
 - a regression revert affecting nouveau users with old userspace
 - intel pageflip deadlock and gpu hang fixes, hsw modesetting hangs

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  Revert "drm: mark context support as a legacy subsystem"
  drm/i915: Don't enable the cursor on a disable pipe
  drm/i915: do not update cursor in crtc mode set
  drm/exynos: fix return value check in lowlevel_buffer_allocate()
  drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
  drm/exynos: Fix address space warning in exynos_drm_buf.c
  drm/exynos: Remove redundant OF dependency
  drm/msm: drop unnecessary set_need_resched()
  drm/i915: kill set_need_resched
  drm/msm: fix potential NULL pointer dereference
  drm/i915/dvo: set crtc timings again for panel fixed modes
  drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
  drm/msm: workaround for missing irq
  drm/msm: return -EBUSY if bo still active
  drm/msm: fix return value check in ERR_PTR()
  drm/msm: fix cmdstream size check
  drm/msm: hangcheck harder
  drm/msm: handle read vs write fences
  drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
  drm/i915: Use proper print format for debug prints
  ...

Pull block IO fixes from Jens Axboe:
 "After merge window, no new stuff this time only a collection of neatly
  confined and simple fixes"

* 'for-3.12/core' of git://git.kernel.dk/linux-block:
  cfq: explicitly use 64bit divide operation for 64bit arguments
  block: Add nr_bios to block_rq_remap tracepoint
  If the queue is dying then we only call the rq->end_io callout. This leaves bios setup on the request, because the caller assumes when the blk_execute_rq_nowait/blk_execute_rq call has completed that the rq->bios have been cleaned up.
  bio-integrity: Fix use of bs->bio_integrity_pool after free
  blkcg: relocate root_blkg setting and clearing
  block: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
  block: trace all devices plug operation

Pull btrfs fixes from Chris Mason:
 "These are mostly bug fixes and a two small performance fixes.  The
  most important of the bunch are Josef's fix for a snapshotting
  regression and Mark's update to fix compile problems on arm"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: create the uuid tree on remount rw
  btrfs: change extent-same to copy entire argument struct
  Btrfs: dir_inode_operations should use btrfs_update_time also
  btrfs: Add btrfs: prefix to kernel log output
  btrfs: refuse to remount read-write after abort
  Btrfs: btrfs_ioctl_default_subvol: Revert back to toplevel subvolume when arg is 0
  Btrfs: don't leak transaction in btrfs_sync_file()
  Btrfs: add the missing mutex unlock in write_all_supers()
  Btrfs: iput inode on allocation failure
  Btrfs: remove space_info->reservation_progress
  Btrfs: kill delay_iput arg to the wait_ordered functions
  Btrfs: fix worst case calculator for space usage
  Revert "Btrfs: rework the overcommit logic to be based on the total size"
  Btrfs: improve replacing nocow extents
  Btrfs: drop dir i_size when adding new names on replay
  Btrfs: replay dir_index items before other items
  Btrfs: check roots last log commit when checking if an inode has been logged
  Btrfs: actually log directory we are fsync()'ing
  Btrfs: actually limit the size of delalloc range
  Btrfs: allocate the free space by the existed max extent size when ENOSPC
  ...

'samples' is 64bit operant, but do_div() second parameter is 32.
do_div silently truncates high 32 bits and calculated result
is invalid.

In case if low 32bit of 'samples' are zeros then do_div() produces
kernel crash.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge tag 'iio-fixes-for-3.12a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of IIO fixes for 3.12

A series of wrong 'struct dev' assumptions in suspend/resume callbacks
following on from this issue being identified in a new driver review.
One to watch out for in future.

A number of driver specific fixes
1) at91 - fix a overflow in clock rate computation
2) dummy - Kconfig dependency issue
3) isl29018 - uninitialized value
4) hmc5843 - measurement conversion bug introduced by recent cleanup.
5) ade7854-spi - wrong return value.

Some IIO core fixes
1) Wrong value picked up for event code creation for a modified channel
2) A null dereference on failure to initialize a buffer after no buffer has
   been in use, when using the available_scan_masks approach.
3) Sampling not stopped when a device is removed. Effects forced removal
   such as hot unplugging.
4) Prevent device going away if a chrdev is still open in userspace.
5) Prevent race on chardev opening and device being freed.
6) Add a missing iio_buffer_init in the call back buffer.

These last few are the first part of a set from Lars-Peter Clausen who
has been taking a closer look at our removal paths and buffer handling
than anyone has for quite some time.

Pull NFS client bugfix from Trond Myklebust:
 "Fix a regression due to incorrect sharing of gss auth caches"

* tag 'nfs-for-3.12-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  RPCSEC_GSS: fix crash on destroying gss auth

Adding the number of bios in a remapped request to 'block_rq_remap'
tracepoint.

Request remapper clones bios in a request to track the completion
status of each bio. So the number of bios can be useful information
for investigation.

Related discussions:
  http://www.redhat.com/archives/dm-devel/2013-August/msg00084.html
  http://www.redhat.com/archives/dm-devel/2013-September/msg00024.htmlSigned-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Users have been complaining of the uuid tree stuff warning that there is no uuid
root when trying to do snapshot operations.  This is because if you mount -o ro
we will not create the uuid tree.  But then if you mount -o rw,remount we will
still not create it and then any subsequent snapshot/subvol operations you try
to do will fail gloriously.  Fix this by creating the uuid_root on remount rw if
it was not already there.  Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

btrfs_ioctl_file_extent_same() uses __put_user_unaligned() to copy some data
back to it's argument struct. Unfortunately, not all architectures provide
__put_user_unaligned(), so compiles break on them if btrfs is selected.

Instead, just copy the whole struct in / out at the start and end of
operations, respectively.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

Commit 2bc55652 (Btrfs: don't update atime on
RO subvolumes) ensures that the access time of an inode is not updated when
the inode lives in a read-only subvolume.
However, if a directory on a read-only subvolume is accessed, the atime is
updated. This results in a write operation to a read-only subvolume. I
believe that access times should never be updated on read-only subvolumes.

To reproduce:

 # mkfs.btrfs -f /dev/dm-3
 (...)
 # mount /dev/dm-3 /mnt
 # btrfs subvol create /mnt/sub
 	Create subvolume '/mnt/sub'
 # mkdir /mnt/sub/dir
 # echo "abc" > /mnt/sub/dir/file
 # btrfs subvol snapshot -r /mnt/sub /mnt/rosnap
 	Create a readonly snapshot of '/mnt/sub' in '/mnt/rosnap'
 # stat /mnt/rosnap/dir
 	File: `/mnt/rosnap/dir'
 	Size: 8         Blocks: 0          IO Block: 4096   directory
 Device: 16h/22d    Inode: 257         Links: 1
 Access: (0755/drwxr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
 	Access: 2013-09-11 07:21:49.389157126 -0400
 	Modify: 2013-09-11 07:22:02.330156079 -0400
 	Change: 2013-09-11 07:22:02.330156079 -0400
 # ls /mnt/rosnap/dir
 	file
 # stat /mnt/rosnap/dir
 	File: `/mnt/rosnap/dir'
 	Size: 8         Blocks: 0          IO Block: 4096   directory
 Device: 16h/22d    Inode: 257         Links: 1
 Access: (0755/drwxr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
 	Access: 2013-09-11 07:22:56.797151670 -0400
 	Modify: 2013-09-11 07:22:02.330156079 -0400
 	Change: 2013-09-11 07:22:02.330156079 -0400
Reported-by: Koen De Wit <koen.de.wit@oracle.com>
Signed-off-by: Guangyu Sun <guangyu.sun@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

The kernel log entries for device label %s and device fsid %pU
are missing the btrfs: prefix. Add those here.
Signed-off-by: Frank Holton <fholton@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

It's still possible to flip the filesystem into RW mode after it's
remounted RO due to an abort. There are lots of places that check for
the superblock error bit and will not write data, but we should not let
the filesystem appear read-write.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

This patch makes it possible to set BTRFS_FS_TREE_OBJECTID as the default
subvolume by passing a subvolume id of 0.
Signed-off-by: chandan <chandan@linux.vnet.ibm.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>