Merge tag 'for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

Add new PHY drivers for SATA and USB in exynos, for USB in sunxi,
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.

This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
This is the physical layer interface for the corresponding host
controller. Currently, only external clock and Gen3 SATA mode
are supported.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This patch adds the APM X-Gene SoC 15Gbps Multi-purpose PHY driver binding
documentation.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The OMAP_USB2 and OMAP_PIPE3 PHY devices will not be
detected if the OMAP_OCP2SCP bus driver is not present.
Make them depend on it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Due to Errata i783, SATA breaks if its DPLL is idled. The recommeded
workaround to issue a softreset to the SATA controller doesn't seem to
work. Here we just prevent SATA DPLL from Idling and hence avoid
the issue altogether.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Limit .power_on() and .power_off() to just control the
PHY power and not the DPLL. The DPLL will be enabled
in .init() and idled in .exit().

Don't reprogram the DPLL if it has been already locked
by the bootloader. This fixes a problem with SATA, where
it fails if SATA was used by the bootloader.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

SATA PHY doesn't need 'wkupclk; and 'refclk' so don't
try to get them for SATA PHY.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

USB and SATA DPLLs need different settings. Provide
the SATA DPLL settings and use the proper DPLL settings
based on device tree node's compatible_id.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

As this driver is no longer USB specific, use generic clock names.
- Fix PLL_SD_SHIFT from 9 to 10
- Don't separate prepare/unprepare clock from enable/disable. This
  ensures optimal power savings.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The dra7-usb2 and am437-usb2 bindings have not yet been used.
Change them to be more elegant.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>

Add a new compatible for OMAP5 since it does not use any of the
OTG operations as of now.
HAS_SRP and SET_VBUS functionalities are used only for OMAP4.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Enable the dra7x errata workaround for false disconnect problem
with USB2PHY. False disconnects were detected with some of the devices.
Reduce the sensitivity of the disconnect logic within the USB2PHY subsystem
to enusre these false disconnects are not registered.

[george.cherian@ti.com]
While at that, pass proper flags for each SoC's. This is a common driver
used across OMAP4,OMAP5,DRA7xx and AM437x USB2PHY.

False disconnect workaround is currently applicable for only DRA7x.
Signed-off-by: Austin Beam <austinbeam@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Adapt phy-omap-usb2 driver for AM437x.
	- Add new comaptible "ti,am437x-usb2" for AM437x
	- Pass proper data to differentiate AM437x and others.
	- AM437x doesnot support  set_vbus and start_srp.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Submit multiple concurrent urbs for HWA isochronous transfer result data
frame reads.  This keeps the read pipeline full and significantly
improves performance in cases where the frame reads cannot be combined
because they are not contiguous or multiples of the max packet size.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When reading the transfer result data for an isochronous in request, if
the current frame actual_length is contiguous with the next frame and
actual_length is a multiple of the DTI endpoint max packet size, combine
the current frame with the next frame in a single URB.  This reduces the
number of URBs that must be submitted in that case which increases
performance and reduces CPU interrupt overhead.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for Exynos 5250. This driver is to replace the old
USB 2.0 PHY driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic
PHY framework. The driver includes support for the Exynos 4x10 and 4x12
SoC families.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Adding devm_of_phy_get will allow to get phys by supplying a
pointer to the struct device_node instead of struct device.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Previously the of_phy_get function took a struct device * and
was declared static. It was impossible to call it from
another driver and thus it was impossible to get phy defined
for a given node. The old function was renamed to _of_phy_get
and was left for internal use. of_phy_get function was added
and it was exported. The function enables to get a phy for
a given device tree node.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Felipe writes:

usb: patches for v3.15

another substantial pull request with new features all over
the place.

dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.

MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.

The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.

Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.

The printer gadget got a fix for a possible deadlock and plugged
a memory leak.

Ethernet drivers now use NAPI for RX which gives improved throughput.

Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>

Merge tag 'for-usb-next-2014-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next

Sarah writes:

xhci: Streams and UAS cleanups, misc cleanups for 3.15

Hi Greg,

Here's 76 patches to queue to usb-next for 3.15.

The bulk of this rather large pull request is the UAS driver cleanup, the
xHCI streams fixes, and the new userspace API for usbfs to be able to use
and alloc/free bulk streams.  I've hammered on these changes, and the UAS
driver seems solid.  The performance numbers are pretty spiffy too:

root@xanatos:~# echo 3 > /proc/sys/vm/drop_caches; dd if=/dev/sdb of=/dev/null bs=4k count=1000M iflag=count_bytes
256000+0 records in
256000+0 records out
1048576000 bytes (1.0 GB) copied, 3.28557 s, 319 MB/s

That's about 100 MB/s faster than my fastest Bulk-only-Transport mass
storage drive.

There's a couple of miscellaneous cleanup patches and non-urgent bug fixes
in here as well:

79699437 xhci: add the meaningful IRQ description if it is empty
bcffae77 xhci: Prevent runtime pm from autosuspending during initialization
e587b8b2 xhci: make warnings greppable
25cd2882 usb/xhci: Change how we indicate a host supports Link PM.

Sarah Sharp

The HWA driver does not do anything with transfer notifications after
receiving the first one and the Alereon HWA allows them to be disabled
as a performance optimization.  This patch sends a vendor specific
command to the Alereon HWA on startup to disable transfer notifications.
If the command is successful, the DTI system is started immediately
since that would normally be started upon the first reception of a
transfer notification which will no longer be sent.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Data for transfer segments in the WA_SEG_DTI_PENDING state is actively
being read by the driver.  Let the buffer read callback handle the
transfer cleanup since cleaning it up in wa_urb_dequeue will cause the
read callback to access invalid memory if the transfer is completed.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch locks rpipe->seg_lock around the entire transfer segment
cleanup loop in wa_urb_dequeue instead of just one case of the switch
statement.  This fixes a race between __wa_xfer_delayed_run and
wa_urb_dequeue where a transfer segment in the WA_SEG_DELAYED state
could be removed from the rpipe seg_list twice leading to memory
corruption.  It also switches the spin_lock call to use the non-irqsave
version since the xfer->lock is already held and irqs already disabled.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No functional change. Moved omap_usb.h from linux/usb/ to linux/phy/.
Also removed the unused members of struct omap_usb (after phy-omap-pipe3
started using it's own header file)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

SATA PHY needs a new compatible ID. Add it to the DT binding documentation.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add wakeup, system and reference clocks to DT binding documentation.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The dra7-usb2 and am437-usb2 bindings have not yet been used.
Change them to be more elegant.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When the request length is aligned to maxpacketsize, sometimes
the return length ret > the user space requested len.

At that time, we will use min_t(size_t, ret, len) to limit the
size in case of user data buffer overflow.

But we need return the min_t(size_t, ret, len) to tell the user
space rightly also.

[ balbi@ti.com: also fix comment's indentation ]
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

According to:"On-The-Go and Embedded Host Supplement to the USB Revision 2.0
Specification July 27, 2012 Revision 2.0 version 1.1a"
- From a_host to a_wait_bcon if !b_conn
- Add transition from a_host to a_wait_vfall if id state is high or a_bus_drop
- From a_wait_vfall to a_idle if a_wait_vfall_tmout
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In order to reduce the interrupt times in the embedded system,
a receiving workqueue is introduced.
This modification also enhanced the overall throughput as the
benefits of reducing interrupt occurrence.

This work was derived from previous work:
u_ether: move hardware transmit to RX workqueue.
Which should be base on codeaurora's work.

However, the benchmark on my platform shows the throughput
with workqueue is slightly better than NAPI.
Signed-off-by: Weinn Jheng <clanlab.proj@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We know what "value" is and it upsets static checkers that we appear to
have doubts about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

These were cut and paste from the ->disconnect function.

Fixes commit 30d577b9bcc4 ('usb: dwc3: gadget: call gadget driver's
->suspend/->resume')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When some xHCI host controllers fall back to use the legacy IRQ,
the member irq_descr of the usb_hcd structure will be empty. This
leads to the empty string of the xHCI host controller in
/proc/interrupts. Here is the example (The irq 19 is the xHCI host
controller):

           CPU0
  0:         91		IO-APIC-edge      	timer
  8:          1         IO-APIC-edge      	rtc0
  9:       7191         IO-APIC-fasteoi   	acpi
 18:        104       	IR-IO-APIC-fasteoi 	ehci_hcd:usb1, ehci_hcd:usb2
 19:        473     	IR-IO-APIC-fasteoi

After applying the patch, the name of the registered xHCI host
controller can be displayed correctly. Here is the example:

           CPU0
  0:         91		IO-APIC-edge      	timer
  8:          1         IO-APIC-edge      	rtc0
  9:       7191         IO-APIC-fasteoi   	acpi
 18:        104       	IR-IO-APIC-fasteoi 	ehci_hcd:usb1, ehci_hcd:usb2
 19:        473     	IR-IO-APIC-fasteoi	xhci_hcd:usb3

Tested on v3.14-rc4.
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Reviewed-by: Nagananda Chumbalkar <nchumbalkar@lenovo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

xHCI driver has its own pci probe function that will call usb_hcd_pci_probe
to register its usb-2 bus, and then continue to manually register the
usb-3 bus. usb_hcd_pci_probe does a pm_runtime_put_noidle at the end and
might thus trigger a runtime suspend before the usb-3 bus is ready.

Prevent the runtime suspend by increasing the usage count in the
beginning of xhci_pci_probe, and decrease it once the usb-3 bus is
ready.

xhci-platform driver is not using usb_hcd_pci_probe to set up
busses and should not need to have it's usage count increased during probe.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Move omap-control binding information to the right location.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Now that omap-usb2 is adapted to the new generic PHY framework,
*set_suspend* ops can be removed from omap-usb2 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

Adapted omap-usb3 PHY driver to Generic PHY Framework and moved phy-omap-usb3
driver in drivers/usb/phy to drivers/phy and also renamed the file to
phy-ti-pipe3 since this same driver will be used for SATA PHY and
PCIE PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This reworks the way SuperSpeed descriptors are added and instead of
having a magic after full and high speed descriptors, it reworks the
whole descriptors block to include a flags field which lists which
descriptors are present and makes future extensions possible.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>