There are bugs on vhci with usb 3.0 storage device. In USB, each SG
list entry buffer should be divisible by the bulk max packet size.
But with native SG support, this problem doesn't matter because the
SG buffer is treated as contiguous buffer. But without native SG
support, USB storage driver breaks SG list into several URBs and the
error occurs because of a buffer size of URB that cannot be divided
by the bulk max packet size. The error situation is as follows.

When USB Storage driver requests 31.5 KB data and has SG list which
has 3584 bytes buffer followed by 7 4096 bytes buffer for some
reason. USB Storage driver splits this SG list into several URBs
because VHCI doesn't support SG and sends them separately. So the
first URB buffer size is 3584 bytes. When receiving data from device,
USB 3.0 device sends data packet of 1024 bytes size because the max
packet size of BULK pipe is 1024 bytes. So device sends 4096 bytes.
But the first URB buffer has only 3584 bytes buffer size. So host
controller terminates the transfer even though there is more data to
receive. So, vhci needs to support SG transfer to prevent this error.

In this patch, vhci supports SG regardless of whether the server's
host controller supports SG or not, because stub driver splits SG
list into several URBs if the server's host controller doesn't
support SG.

To support SG, vhci sets URB_DMA_MAP_SG flag in urb->transfer_flags
if URB has SG list and this flag will tell stub driver to use SG
list. After receiving urb from stub driver, vhci clear URB_DMA_MAP_SG
flag to avoid unnecessary DMA unmapping in HCD.

vhci sends each SG list entry to stub driver. Then, stub driver sees
the total length of the buffer and allocates SG table and pages
according to the total buffer length calling sgl_alloc(). After stub
driver receives completed URB, it again sends each SG list entry to
vhci.

If the server's host controller doesn't support SG, stub driver
breaks a single SG request into several URBs and submits them to
the server's host controller. When all the split URBs are completed,
stub driver reassembles the URBs into a single return command and
sends it to vhci.

Moreover, in the situation where vhci supports SG, but stub driver
does not, or vice versa, usbip works normally. Because there is no
protocol modification, there is no problem in communication between
server and client even if the one has a kernel without SG support.

In the case of vhci supports SG and stub driver doesn't, because
vhci sends only the total length of the buffer to stub driver as
it did before the patch applied, stub driver only needs to allocate
the required length of buffers using only kmalloc() regardless of
whether vhci supports SG or not. But stub driver has to allocate
buffer with kmalloc() as much as the total length of SG buffer which
is quite huge when vhci sends SG request, so it has overhead in
buffer allocation in this situation.

If stub driver needs to send data buffer to vhci because of IN pipe,
stub driver also sends only total length of buffer as metadata and
then sends real data as vhci does. Then vhci receive data from stub
driver and store it to the corresponding buffer of SG list entry.

And for the case of stub driver supports SG and vhci doesn't, since
the USB storage driver checks that vhci doesn't support SG and sends
the request to stub driver by splitting the SG list into multiple
URBs, stub driver allocates a buffer for each URB with kmalloc() as
it did before this patch.

* Test environment

Test uses two difference machines and two different kernel version
to make mismatch situation between the client and the server where
vhci supports SG, but stub driver does not, or vice versa. All tests
are conducted in both full SG support that both vhci and stub support
SG and half SG support that is the mismatch situation. Test kernel
version is 5.3-rc6 with commit "usb: add a HCD_DMA flag instead of
guestimating DMA capabilities" to avoid unnecessary DMA mapping and
unmapping.

 - Test kernel version
    - 5.3-rc6 with SG support
    - 5.1.20-200.fc29.x86_64 without SG support

* SG support test

 - Test devices
    - Super-speed storage device - SanDisk Ultra USB 3.0
    - High-speed storage device - SMI corporation USB 2.0 flash drive

 - Test description

Test read and write operation of mass storage device that uses the
BULK transfer. In test, the client reads and writes files whose size
is over 1G and it works normally.

* Regression test

 - Test devices
    - Super-speed device - Logitech Brio webcam
    - High-speed device  - Logitech C920 HD Pro webcam
    - Full-speed device  - Logitech bluetooth mouse
                         - Britz BR-Orion speaker
    - Low-speed device   - Logitech wired mouse

 - Test description

Moving and click test for mouse. To test the webcam, use gnome-cheese.
To test the speaker, play music and video on the client. All works
normally.

* VUDC compatibility test

VUDC also works well with this patch. Tests are done with two USB
gadget created by CONFIGFS USB gadget. Both use the BULK pipe.

        1. Serial gadget
        2. Mass storage gadget

 - Serial gadget test

Serial gadget on the host sends and receives data using cat command
on the /dev/ttyGS<N>. The client uses minicom to communicate with
the serial gadget.

 - Mass storage gadget test

After connecting the gadget with vhci, use "dd" to test read and
write operation on the client side.

Read  - dd if=/dev/sd<N> iflag=direct of=/dev/null bs=1G count=1
Write - dd if=<my file path> iflag=direct of=/dev/sd<N> bs=1G count=1
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190828032741.12234-1-suwan.kim027@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable static DRD mode in Intel platforms which guarantees
successful role switch all the time. This fixes issues like
software role switch failure after cold boot and issue with
role switch when USB 3.0 cable is used. But, do not enable
static DRD mode for Cherrytrail devices which rely on firmware
for role switch.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/1567079760-24822-2-git-send-email-saranya.gopal@intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In platforms like Cherrytrail, 'SW switch enable' bit
should not be enabled for role switch. This patch
adds a property to Intel USB Role Switch platform driver
to denote that SW switch should be disabled in
Cherrytrail devices.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1567079760-24822-1-git-send-email-saranya.gopal@intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Calls to USB2 generic PHY calibrate() method has been moved to HCD core,
which now successfully handles generic PHYs and their calibration after
every HCD reset. This fixes all the timing issues related to PHY
calibration done directly from DWC3 driver: incorrect operation after
system suspend/resume or USB3.0 detection failure when XHCI-plat driver
compiled as separate module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Jochen Sprickerhof <jochen@sprickerhof.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20190829053028.32438-3-m.szyprowski@samsung.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some PHYs (for example Exynos5 USB3.0 DRD PHY) require calibration to be
done after every USB HCD reset. Generic PHY framework has been already
extended with phy_calibrate() function in commit 36914111 ("drivers:
phy: add calibrate method"). This patch adds support for it to generic
PHY handling code in USB HCD core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Jochen Sprickerhof <jochen@sprickerhof.de>
Link: https://lore.kernel.org/r/20190829053028.32438-2-m.szyprowski@samsung.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use devm_reset_controller_register to get rid
of manual unregistration.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190902014323.27588-1-hslester96@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch uses xhci_plat_priv.quirks to simplify. The previous
code had conditions to set some quirks in xhci_rcar_init_quirk().
But, the xhci_rcar_init_quirk() is called at the same conditions.
So, no behavior change.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1567425698-27560-4-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To avoid copy-and-paste setting of xhci_plat_priv for R-Car SoCs,
this patch add a helper macro SET_XHCI_PLAT_PRIV_FOR_RCAR.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1567425698-27560-3-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To simplify adding xhci->quirks instead of the .init_quirk()
function, this patch adds a new parameter "quirks" into
the struct xhci_plat_priv.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1567425698-27560-2-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Xhci re-enables a slot on transaction error in set_address using
xhci_disable_slot() + xhci_alloc_dev().

But in this case, xhci_alloc_dev() creates debugfs entries upon an
existing device without cleaning up old entries, thus memory leaks.

So this patch simply moves calling xhci_debugfs_free_dev() from
xhci_free_dev() to xhci_disable_slot().

[added "possible" to header as this is about failure codepath -Mathias]
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1567172356-12915-5-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Software can set a Transfer State Preserve (TSP) flag to maintain
data toggle and sequence number when issuing a reset endpoint
command.

xhci driver is using TSP for soft retry, we want to show TSP usage
in tracing as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1567172356-12915-4-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to use GFP_ATOMIC to allocate 'req'. GFP_KERNEL should be
enough and is already used for another allocation juste a few lines below.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1567172356-12915-3-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the 'kmalloc()' fails, we need to undo the previous
'dbc_alloc_request()' call.

Because of the more similar function name, it is more logical to use
'dbc_free_request()' instead of 'xhci_dbc_free_req()'.

Both are equivalent here because:
 static void xhci_dbc_free_req(struct dbc_ep *dep, struct dbc_request *req)
 {
 	kfree(req->buf);
 	dbc_free_request(dep, req);
 }
and 'req->buf' is known to be NULL at this point
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1567172356-12915-2-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190903120710.30128-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the check on a non-zero return code in ret is false because
ret has been initialized to zero.  I believe that ret should be assigned
to the return from the call to readl_poll_timeout_atomic before the
check on ret.  Since ret is being re-assinged the original initialization
of ret to zero can be removed.

Addresses-Coverity: ("'Constant' variable guards dead code")
Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190902145035.18200-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the case where an allocation fails for priv_ep ret is
assigned -ENOMEM and the code exits via the exit path 'err'.
The exit path returns -ENOMEM without using variable ret, so
the assingment is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190902184334.27406-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If CONFIG_REGMAP_I2C is not set, building fails:

drivers/usb/typec/tps6598x.o: In function `tps6598x_probe':
tps6598x.c:(.text+0x5f0): undefined reference to `__devm_regmap_init_i2c'

Select REGMAP_I2C to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0a4c005b ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190903121026.22148-1-yuehaibing@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/usb/cdns3/gadget.c: In function '__cdns3_gadget_init':
drivers/usb/cdns3/gadget.c:2665:23: warning:
 variable 'priv_dev' set but not used [-Wunused-but-set-variable]
drivers/usb/cdns3/gadget.c: In function cdns3_start_all_request:
drivers/usb/cdns3/gadget.c:357:24: warning:
 variable priv_req set but not used [-Wunused-but-set-variable]

They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190903120445.22204-1-yuehaibing@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/cdns3/ep0.c: In function cdns3_ep0_feature_handle_device:
drivers/usb/cdns3/ep0.c:290:6: warning: variable wIndex set but not used [-Wunused-but-set-variable]
drivers/usb/cdns3/ep0.c:289:6: warning: variable wValue set but not used [-Wunused-but-set-variable]

wIndex is never used, so remove it.
wValue should be use in the switch statement.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190903120615.19504-1-yuehaibing@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that these drivers use the usb localmem pool there is no need to
select DMA_DECLARE_COHERENT.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190903084615.19161-7-hch@lst.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These wrappers have never seen use and have been commented out
for a long time.  Remove them for good.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190903084615.19161-6-hch@lst.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that we have the local memory pool implemented there is no
need to use dma_declare_coherent_memory.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190903084615.19161-5-hch@lst.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dma_mask on its own doesn't mean much.  Instead check for the actual
flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190903084615.19161-4-hch@lst.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver doesn't support normal DMA, only direct access to its
local memory.  Remove the HCD_DMA flag to properly express that fact.

Fixes: 7b81cb6b ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190903084615.19161-3-hch@lst.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver doesn't support normal DMA, only direct access to its
local memory.  Remove the HCD_DMA flag to properly express that fact.

Fixes: 7b81cb6b ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190903084615.19161-2-hch@lst.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the usb fixes in here for testing
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

USB: Changes for v5.4 merge window

With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.

The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

* tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (45 commits)
  usb: gadget: net2280: Add workaround for AB chip Errata 11
  usb: gadget: net2280: Move all "ll" registers in one structure
  usb: dwc3: gadget: Workaround Mirosoft's BESL check
  usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
  usb: cdns3: Add Cadence USB3 DRD Driver
  usb: common: Simplify usb_decode_get_set_descriptor function.
  usb: common: Patch simplify usb_decode_set_clear_feature function.
  usb: common: Separated decoding functions from dwc3 driver.
  dt-bindings: add binding for USBSS-DRD controller.
  usb: gadget: composite: Set recommended BESL values
  usb: dwc3: gadget: Set BESL config parameter
  usb: dwc3: Separate field holding multiple properties
  usb: gadget: Export recommended BESL values
  usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
  usb: udc: lpc32xx: silence fall-through warning
  usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disables
  usb: udc: lpc32xx: remove set but not used 3 variables
  usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
  usb: dwc3: st: Add of_dev_put() in probe function
  usb: dwc3: st: Add of_node_put() before return in probe function
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for reported issues for
  5.3-rc7

  Also included in here is the documentation for how we are handling
  hardware issues under embargo that everyone has finally agreed on, as
  well as a MAINTAINERS update for the suckers who agreed to handle the
  LICENSES/ files.

  All of these have been in linux-next last week with no reported
  issues"

* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  fsi: scom: Don't abort operations for minor errors
  vmw_balloon: Fix offline page marking with compaction
  VMCI: Release resource if the work is already queued
  Documentation/process: Embargoed hardware security issues
  lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
  mei: me: add Tiger Lake point LP device ID
  intel_th: pci: Add Tiger Lake support
  intel_th: pci: Add support for another Lewisburg PCH
  stm class: Fix a double free of stm_source_device
  MAINTAINERS: add entry for LICENSES and SPDX stuff
  fpga: altera-ps-spi: Fix getting of optional confd gpio

Pull USB fixes from Greg KH:
 "Here are some small USB fixes that have been in linux-next this past
  week for 5.3-rc7

  They fix the usual xhci, syzbot reports, and other small issues that
  have come up last week.

  All have been in linux-next with no reported issues"

* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: cdc-wdm: fix race between write and disconnect due to flag abuse
  usb: host: xhci: rcar: Fix typo in compatible string matching
  usb: host: xhci-tegra: Set DMA mask correctly
  USB: storage: ums-realtek: Whitelist auto-delink support
  USB: storage: ums-realtek: Update module parameter description for auto_delink_en
  usb: host: ohci: fix a race condition between shutdown and irq
  usb: hcd: use managed device resources
  typec: tcpm: fix a typo in the comparison of pdo_max_voltage
  usb-storage: Add new JMS567 revision to unusual_devs
  usb: chipidea: udc: don't do hardware access if gadget has stopped
  usbtmc: more sanity checking for packet size
  usb: udc: lpc32xx: silence fall-through warning

Pull networking fixes from David Miller:

 1) Fix some length checks during OGM processing in batman-adv, from
    Sven Eckelmann.

 2) Fix regression that caused netfilter conntrack sysctls to not be
    per-netns any more. From Florian Westphal.

 3) Use after free in netpoll, from Feng Sun.

 4) Guard destruction of pfifo_fast per-cpu qdisc stats with
    qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
    in pfifo_fast_enqueue().

 5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.

 6) Handle neigh events on internal ports correctly in nfp, from John
    Hurley.

 7) Clear SKB timestamp in NF flow table code so that it does not
    confuse fq scheduler. From Florian Westphal.

 8) taprio destroy can crash if it is invoked in a failure path of
    taprio_init(), because the list head isn't setup properly yet and
    the list del is unconditional. Perform the list add earlier to
    address this. From Vladimir Oltean.

 9) Make sure to reapply vlan filters on device up, in aquantia driver.
    From Dmitry Bogdanov.

10) sgiseeq driver releases DMA memory using free_page() instead of
    dma_free_attrs(). From Christophe JAILLET.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
  net: seeq: Fix the function used to release some memory in an error handling path
  enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
  net: bcmgenet: use ethtool_op_get_ts_info()
  tc-testing: don't hardcode 'ip' in nsPlugin.py
  net: dsa: microchip: add KSZ8563 compatibility string
  dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
  net: aquantia: fix out of memory condition on rx side
  net: aquantia: linkstate irq should be oneshot
  net: aquantia: reapply vlan filters on up
  net: aquantia: fix limit of vlan filters
  net: aquantia: fix removal of vlan 0
  net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
  taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
  taprio: Fix kernel panic in taprio_destroy
  net: dsa: microchip: fill regmap_config name
  rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
  net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
  amd-xgbe: Fix error path in xgbe_mod_init()
  netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
  mac80211: Correctly set noencrypt for PAE frames
  ...

In commit 99cd149e ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.

Fix it now.

Rename the corresponding label to something more in line.

Fixes: 99cd149e ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for x86:

   - Fix the bogus detection of 32bit user mode for uretprobes which
     caused corruption of the user return address resulting in
     application crashes. In the uprobes handler in_ia32_syscall() is
     obviously always returning false on a 64bit kernel. Use
     user_64bit_mode() instead which works correctly.

   - Prevent large page splitting when ftrace flips RW/RO on the kernel
     text which caused iTLB performance issues. Ftrace wants to be
     converted to text_poke() which avoids the problem, but for now
     allow large page preservation in the static protections check when
     the change request spawns a full large page.

   - Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
     is configured via device tree. In the device tree case the GSI 1:1
     mapping is meaningless therefore the lower bound which protects the
     GSI range on ACPI machines is irrelevant. Return the lower bound
     which the core hands to the function instead of blindly returning 0
     which causes the core to allocate the invalid virtual interupt
     number 0 which in turn prevents all drivers from allocating and
     requesting an interrupt.

   - Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
     APIC driver. That uses physical destination mode where LDR/DFR are
     ignored, but the initialization and the missing clear of LDR caused
     the APIC to be left in a inconsistent state on kexec/reboot.

   - Clear LDR when clearing the APIC registers so the APIC is in a well
     defined state.

   - Initialize variables proper in the find_trampoline_placement()
     code.

   - Silence GCC( build warning for the real mode part of the build"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
  x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
  x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
  x86/apic: Include the LDR when clearing out APIC registers
  x86/apic: Do not initialize LDR and DFR for bigsmp
  uprobes/x86: Fix detection of 32-bit user mode
  x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines

Pull perf fixes from Thomas Gleixner:
 "Two fixes for perf x86 hardware implementations:

   - Restrict the period on Nehalem machines to prevent perf from
     hogging the CPU

   - Prevent the AMD IBS driver from overwriting the hardwre controlled
     and pre-seeded reserved bits (0-6) in the count register which
     caused a sample bias for dispatched micro-ops"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
  perf/x86/intel: Restrict period on Nehalem

Pull turbostat updates from Len Brown:
 "User-space turbostat (and x86_energy_perf_policy) patches.

  They are primarily bug fixes from users"

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: update version number
  tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
  tools/power turbostat: Fix caller parameter of get_tdp_amd()
  tools/power turbostat: Fix CPU%C1 display value
  tools/power turbostat: do not enforce 1ms
  tools/power turbostat: read from pipes too
  tools/power turbostat: Add Ice Lake NNPI support
  tools/power turbostat: rename has_hsw_msrs()
  tools/power turbostat: Fix Haswell Core systems
  tools/power turbostat: add Jacobsville support
  tools/power turbostat: fix buffer overrun
  tools/power turbostat: fix file descriptor leaks
  tools/power turbostat: fix leak of file descriptor on error return path
  tools/power turbostat: Make interval calculation per thread to reduce jitter
  tools/power turbostat: remove duplicate pc10 column
  tools/power x86_energy_perf_policy: Fix argument parsing
  tools/power: Fix typo in man page
  tools/power/x86: Enable compiler optimisations and Fortify by default
  tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2

Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.

Fixes: 19971f5e ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change enables the use of SW timestamping on the Raspberry Pi 4.

bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.

Similar to commit a8f5cb9e ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the following tdc test fails on Fedora:

 # ./tdc.py -e 2638
  -- ns/SubPlugin.__init__
 Test 2638: Add matchall and try to get it
 -----> prepare stage *** Could not execute: "$TC qdisc add dev $DEV1 clsact"
 -----> prepare stage *** Error message: "/bin/sh: ip: command not found"
 returncode 127; expected [0]
 -----> prepare stage *** Aborting test run.

Let nsPlugin.py use the 'IP' variable introduced with commit 92c1a19e
("tc-tests: added path to ip command in tdc"), so that the path to 'ip' is
correctly resolved to the value we have in tdc_config.py.

 # ./tdc.py -e 2638
  -- ns/SubPlugin.__init__
 Test 2638: Add matchall and try to get it
 All test results:
 1..1
 ok 1 2638 - Add matchall and try to get it

Fixes: 489ce2f4 ("tc-testing: Restore original behaviour for namespaces in tdc")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Razvan Stefanescu says:

====================
net: dsa: microchip: add KSZ8563 support

This patchset adds compatibility string for the KSZ8563 switch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>