- 15 Feb, 2024 18 commits
-
-
Vaishnav Achath authored
The J722S is a family of application processors built for Automotive and Linux Application development. J722S family of SoCs is a superset of the AM62P SoC family and shares similar memory map, thus the nodes are being reused from AM62P includes instead of duplicating the definitions. Some highlights of J722S SoC (in addition to AM62P SoC features) are: * Two Cortex-R5F for Functional Safety or general-purpose usage and two C7x floating point vector DSP with Matrix Multiply Accelerator for deep learning. * Vision Processing Accelerator (VPAC) with image signal processor and Depth and Motion Processing Accelerator (DMPAC). * 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio, 4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP, ePWM, among other peripherals. For those interested, more details about this SoC can be found in the Technical Reference Manual here: https://www.ti.com/lit/zip/sprujb3Co-developed-by:Jayesh Choudhary <j-choudhary@ti.com> Signed-off-by:
Vaishnav Achath <vaishnav.a@ti.com> Reviewed-by:
Manorit Chawdhry <m-chawdhry@ti.com> Link: https://lore.kernel.org/r/20240206100608.127702-3-vaishnav.a@ti.comSigned-off-by:
Vignesh Raghavendra <vigneshr@ti.com>
-
Vaishnav Achath authored
Add bindings for TI J722S family of devices. Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240206100608.127702-2-vaishnav.a@ti.comSigned-off-by:
-
Baocheng Su authored
Main differences between the new variant and Advanced PG2: 1. Arduino interface is removed. Instead, an new ASIC is added for communicating with PLC 1200 signal modules. 2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is available. 3. DP interface is removed. Instead, to communicate with PLC 1200 signal modules, a USB 3.0 type B connector is added but the signals are actually not USB. 4. DDR size is increased to 4 GB. 5. Two sensors are added, one tilt sensor and one light sensor. The light sensor it not yet added to the DT at this stage as it depends on to-be-added bindings. Co-developed-by:
Chao Zeng <chao.zeng@siemens.com> Signed-off-by:
Li Hua Qian <huaqian.li@siemens.com> Signed-off-by:
Baocheng Su <baocheng.su@siemens.com> [Jan: rebase over dtsi refactorings, split-out light sensor, improve LEDs] Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Link: https://lore.kernel.org/r/d24e920547986499f6e8e39c833e414679b12ab4.1707463401.git.jan.kiszka@siemens.comSigned-off-by:
-
Jan Kiszka authored
Add function and color properties and use the common scheme for the node name. We can't change the user-visible labels, though, due to existing userspace relying on the current format. Signed-off-by:
-
Jan Kiszka authored
There is a variant coming which does not support the Display Port. Move all related bits into a separate dtsi so that only those variants supporting the interface can include it. Along that, remove a redundant clock setting from k3-am65-iot2050-common-pg1.dtsi. Signed-off-by:
-
Jan Kiszka authored
Already simplifies the existing code by avoid the switch back in the m2 variant to what k3-am65-main.dtsi provided as base. Signed-off-by:
-
Jan Kiszka authored
A new variant is to be added which will not have a arduino connector like the existing ones. Factor out all bits that are specific to this connector. The split is not perfect because wkup_gpio0 is defined based on what is common to all variants having the connector, thus containing also connector-unrelated information. But this is still cleaner than replicating this node into all 4 variants. Signed-off-by:
-
Baocheng Su authored
The R5 lockstep disabling should be common for all PG2 boards, move it from variants dts to common-pg2.dtsi. As now the Basic PG2 consumes this twice, move Basic disabling to the PG1 variant. Signed-off-by:
-
Su Bao Cheng authored
This new variant is derived from the Advanced PG2 board, removing the Arduino interface, and adding a new ASIC for communicating with the PLC 1200 signal modules. Signed-off-by:
-
Andrejs Cainikovs authored
AM62 USB works with some devices, while failing to operate with others. [ 560.189822] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller [ 560.195631] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 2 [ 574.388509] xhci-hcd xhci-hcd.4.auto: can't setup: -110 [ 574.393814] xhci-hcd xhci-hcd.4.auto: USB bus 2 deregistered [ 574.399544] xhci-hcd: probe of xhci-hcd.4.auto failed with error -110 This seems to be related to LPM (Link Power Management), and disabling it turns USB into reliable working state. As per AM62 reference manual: > 4.8.2.1 USB2SS Unsupported Features > > The following features are not supported on this family of devices: > ... > - USB 2.0 ECN: Link Power Management (LPM) > ... Fixes: 2240f96c ("arm64: dts: ti: k3-am62-main: Add support for USB") Signed-off-by:
Andrejs Cainikovs <andrejs.cainikovs@toradex.com> Reviewed-by:
Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by:
Roger Quadros <rogerq@ti.com> Link: https://lore.kernel.org/r/20240209130213.38908-1-andrejs.cainikovs@gmail.comSigned-off-by:
-
Francesco Dolcini authored
Set VDD_CORE minimum voltage to 0.75V, TI AM62 can run at either 0.75V or 0.85V depending on the actual speed grade and on the maximum configured speed (1.4GHz frequency requires 0.85V). The actual value is programmed into the PMIC EEPROM during manufacturing (according to the SOC speed grade) and this ensure that both the voltage values are valid and therefore the OS will not overwrite the value programmed into the PMIC. Signed-off-by:
-
Tony Lindgren authored
The devices in the wkup domain are capable of waking up the system from suspend. We can configure the wkup domain devices in a generic way using the ti-sysc interconnect target module driver like we have done with the earlier TI SoCs. As ti-sysc manages the SYSCONFIG related registers independent of the child hardware device, the wake-up configuration is also set even if wkup_uart0 is reserved by sysfw. The wkup_uart0 device has interconnect target module register mapping like dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP block in the target module. The power domain and clock affects the whole interconnect target module. Note we change the functional clock name to follow the ti-sysc binding and use "fck" instead of "fclk". Also note that we need to disable the target module reset as noted by Markus. Otherwise the sysfw using wkup_uart0 can get confused on some devices leading to boot time issues such as mbox timeouts. Tested-by:
Dhruva Gole <d-gole@ti.com> Reviewed-by:
Kevin Hilman <khilman@baylibre.com> Tested-by:
Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20240213112510.6334-1-tony@atomide.comSigned-off-by:
-
Nathan Morrisson authored
The phyBOARD-Lyra has a GPIO fan header. This overlay enables the fan header and sets the fan to turn on at 65C. Signed-off-by:
Nathan Morrisson <nmorrisson@phytec.com> Reviewed-by:
Wadim Egorov <w.egorov@phytec.de> Link: https://lore.kernel.org/r/20240213005248.1027842-1-nmorrisson@phytec.comSigned-off-by:
-
Romain Naour authored
The tps659413 and tps659411 nodes set WKUP_GPIO0_7 (G28) pin as input to be used as PMIC interrupt but uses 9 (WKUP_GPIO0_9) as "interrupts" property. Replace 9 by 7 for both tps659413 and tps659411 after checking in the board schematic [1]. [1] https://www.ti.com/tool/SK-TDA4VM Fixes: b808cef0 ("arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs") Cc: Neha Malcom Francis <n-francis@ti.com> Signed-off-by:
Romain Naour <romain.naour@smile.fr> Reviewed-by:
Neha Malcom Francis <n-francis@ti.com> Link: https://lore.kernel.org/r/20240209171146.307465-2-romain.naour@smile.frSigned-off-by:
-
Romain Naour authored
The tps659413 node set WKUP_GPIO0_83 (AA37) pin as input to be used as PMIC interrupt but uses 39 (WKUP_GPIO0_39) as "interrupts" property. Replace 39 by 83 after checking in the board schematic [1]. [1] https://www.ti.com/tool/SK-AM69 Fixes: 865a1593 ("arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC") Cc: Neha Malcom Francis <n-francis@ti.com> Signed-off-by:
-
Andrejs Cainikovs authored
Add support for Verdin USB1 interface, implements role switch functionality using "gpio-usb-b-connector", VBUS is also now controlled with "regulator-fixed" using a standard GPIO. Signed-off-by:
-
Kishon Vijay Abraham I authored
Add overlay for PCIe (uses the second instance of PCIe in AM654x) and USB3.0 SERDES personality card The PCIe3/USB3 card is provided with the AM65x GP EVM configuration [1] so apply the overlay to k3-am654-gp-evm.dtb [1] https://www.ti.com/lit/ug/spruim7/spruim7.pdfSigned-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-3-70bae3e91597@kernel.orgSigned-off-by:
-
Roger Quadros authored
Enable both SERDES and PCIe DT nodes in order to get PCIe working on the SERDES PCIe x2 personality card. The daughter card also has a USB 2.0 dual-role port. As the base board already supports a 2.0 dual-role port, enable the port on the SERDES card to be a host only port. This will prevent user confusion as having 2 ports in device mode often leads to confusion as to which port is bound to the gadget function driver. The PCIe x2 card is provided with the AM65x IDK configuration [1] so apply the overlay to k3-am654-idk.dtb [1] https://www.ti.com/lit/ug/spruim6a/spruim6a.pdfCo-developed-by:
-
- 14 Feb, 2024 11 commits
-
-
Roger Quadros authored
Add the overlay dtbo file to a Makefile target so it can be picked by the dtbs_install command. Fixes: b8690ed3 ("arm64: dts: ti: am65x: Add Rocktech OLDI panel DT overlay") Signed-off-by:
Aradhya Bhatia <a-bhatia1@ti.com> Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-1-70bae3e91597@kernel.orgSigned-off-by:
-
Andrew Davis authored
The main_conf node does not need to be a syscon, so change to "simple-bus". This removes a DTS check warning. Signed-off-by:
Andrew Davis <afd@ti.com> Link: https://lore.kernel.org/r/20240124184722.150615-11-afd@ti.comSigned-off-by:
-
Andrew Davis authored
The main_conf node does not need to be a syscon, so change to "simple-bus". This removes a DTS check warning. Signed-off-by:
-
Andrew Davis authored
To do this we convert hbmc-mux to "reg-mux", then the FSS node does not need to be a syscon, so change to "simple-bus". This removes a DTS check warning. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
Andrew Davis authored
This removes a dependency on the parent node being a syscon node. Convert from mmio-mux to reg-mux adjusting node name and properties as needed. Signed-off-by:
-
- 06 Feb, 2024 11 commits
-
-
Nishanth Menon authored
SPDX identifier GPL-2.0 has been deprecated since license list version 3.0. Use GPL-2.0-only to be specific. Signed-off-by:
Nishanth Menon <nm@ti.com> Acked-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20240122145539.194512-17-nm@ti.comSigned-off-by:
-
Nishanth Menon authored
SPDX identifier GPL-2.0 has been deprecated since license list version 3.0. Use GPL-2.0-only to be specific. Cc: Chao Zeng <chao.zeng@siemens.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Le Jin <le.jin@siemens.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for device trees belonging to PHYTEC Messtechnik GmbH and PHYTEC America, LLC platforms. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the copyright year to sync with current year to indicate license change. Cc: Garrett Giordano <ggiordano@phytec.com> Cc: Wadim Egorov <w.egorov@phytec.de> Acked-by:
Garrett Giordano <ggiordano@phytec.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for device trees belonging to BeagleBoard.org Foundation platforms. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the copyright year to sync with current year to indicate license change. Cc: Ayush Singh <ayushdevel1325@gmail.com> Cc: Jason Kridner <jkridner@beagleboard.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Wadim Egorov <w.egorov@phytec.de> Acked-by:
Ayush Singh <ayushdevel1325@gmail.com> Acked-by:
Jason Kridner <jkridner@beagleboard.org> Acked-by:
Robert Nelson <robertcnelson@gmail.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change. Signed-off-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change. Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change (and add it at least for one file which was missing TI copyright). Cc: Apelete Seketeli <aseketeli@baylibre.com> Cc: Jerome Neanne <jneanne@baylibre.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Tony Lindgren <tony@atomide.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change (and add it at least for one file which was missing TI copyright). Cc: Esteban Blanc <eblanc@baylibre.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Pierre Gondois <pierre.gondois@arm.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by:
Esteban Blanc <eblanc@baylibre.com> Acked-by:
Pierre Gondois <pierre.gondois@arm.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change (and add it at least for one file which was missing TI copyright). Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de> Cc: Jerome Neanne <jneanne@baylibre.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Pierre Gondois <pierre.gondois@arm.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change (and add it at least for one file which was missing TI copyright). Cc: Esteban Blanc <eblanc@baylibre.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Pierre Gondois <pierre.gondois@arm.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by:
-
Nishanth Menon authored
Modify license to include dual licensing as GPL-2.0-only OR MIT license for SoC and TI evm device tree files. This allows for Linux kernel device tree to be used in other Operating System ecosystems such as Zephyr or FreeBSD. While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with latest SPDX conventions (GPL-2.0 is deprecated). While at this, update the TI copyright year to sync with current year to indicate license change (and add it at least for one file which was missing TI copyright). Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Cc: Pierre Gondois <pierre.gondois@arm.com> Cc: Rob Herring <robh@kernel.org> Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by:
Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Acked-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by:
-
