Jakub Kicinski says:

====================
devlink: add the ability to update device flash

This series is the second step to allow trouble shooting and recovering
devices in bad state without the use of netdevs as handles.  We can
already query FW versions over devlink, now we add the ability to update
the FW.  This will allow drivers to implement some from of "limp-mode"
where the device can't really be used for networking and hence has no
netdev, but we can interrogate it over devlink and fix the broken FW.

Small but nice advantage of devlink is that it only holds the devlink
instance lock during flashing, unlike ethtool which holds rtnl_lock().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Devlink now allows updating device flash.  Implement this
callback.

Compared to ethtool update we no longer have to release
the networking locks - devlink doesn't take them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If driver does not support ethtool flash update operation
call into devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devlink flash update command. Advanced NICs have firmware
stored in flash and often cryptographically secured. Updating
that flash is handled by management firmware. Ethtool has a
flash update command which served us well, however, it has two
shortcomings:
 - it takes rtnl_lock unnecessarily - really flash update has
   nothing to do with networking, so using a networking device
   as a handle is suboptimal, which leads us to the second one:
 - it requires a functioning netdev - in case device enters an
   error state and can't spawn a netdev (e.g. communication
   with the device fails) there is no netdev to use as a handle
   for flashing.

Devlink already has the ability to report the firmware versions,
now with the ability to update the firmware/flash we will be
able to recover devices in bad state.

To enable updates of sub-components of the FW allow passing
component name.  This name should correspond to one of the
versions reported in devlink info.

v1: - replace target id with component name (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: improve and use phy_resolve_aneg_linkmode

Improve phy_resolve_aneg_linkmode and use it in genphy_read_status.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have phy_resolve_aneg_linkmode() we can make
genphy_read_status() much simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have the settings array of modes which is sorted based on aneg
priority. Instead of checking each mode manually let's simply iterate
over the sorted settings.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check that filter is not NULL before passing it to tcf_walker->fn()
callback in cls_cgroup_walk(). This can happen when cls_cgroup_change()
failed to set first filter.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check that filter is not NULL before passing it to tcf_walker->fn()
callback. This can happen when mall_change() failed to offload filter to
hardware.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in route4_walk() to unify tp->walk() behavior among
classifier implementations.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in fw_walk() to unify tp->walk() behavior among classifier
implementations.

Fixes: ed76f5ed ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use existing skb_put_data() and skb_trim() instead of open-coding them,
with the skb_put_data() first so that logically, `skb` still contains the
data to be copied in its data..tail area when skb_put_data() reads it.
This change on its own is a cleanup, and it is also necessary for potential
future integration of skbuffs with things like KASAN.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a dedicated thermal zone for each QSFP/SFP module. The current
temperature is obtained from the module's temperature sensor and the
trip points are set based on the warning and critical thresholds
read from the module.

A cooling device (fan) is bound to all the thermal zones. The
thermal zone governor is set to user space in order to avoid
collisions between thermal zones.
For example, one thermal zone might want to increase the speed of
the fan, whereas another one would like to decrease it.

Deferring this decision to user space allows the user to the take
the most suitable decision.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
tracepoints in neighbor subsystem

Roopa Prabhu (2):
  trace: events: add a few neigh tracepoints
  neigh: hook tracepoints in neigh update code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

hook tracepoints at the end of functions that
update a neigh entry. neigh_update gets an additional
tracepoint to trace the update flags and old and new
neigh states.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal here is to trace neigh state changes covering all possible
neigh update paths. Plus have a specific trace point in neigh_update
to cover flags sent to neigh_update.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: add and use genphy_c45_an_config_an

This series adds genphy_c45_an_config_an() and uses it in the
marvell10g diver. In addition patch 4 aligns the aneg configuration
with what is done in genphy_config_aneg().

v2:
- in patch 2 changed function name to genphy_c45_an_config_aneg
- in patch 3 add a comment regarding 1000BaseT vendor registers

v3:
- rebase patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Even if the advertisement registers content didn't change, we may have
just switched to aneg, and therefore have to trigger an aneg restart.
This matches the behavior of genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new function genphy_c45_config_aneg() in mv3310_config_aneg().

v2:
- add a comment regarding 1000BaseT vendor registers
v3:
- rebased
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: patch splitted]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

C45 configuration of 10/100 and multi-giga bit auto negotiation
advertisement is standardized. Configuration of 1000Base-T however
appears to be vendor specific. Move the generic code out of the
Marvell driver into the common phy-c45.c file.

v2:
- change function name to genphy_c45_an_config_aneg
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use new helper linkmode_adv_to_mii_10gbt_adv_t and split patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper linkmode_adv_to_mii_10gbt_adv_t(), similar to
linkmode_adv_to_mii_adv_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf-next 2019-02-16

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) numerous libbpf API improvements, from Andrii, Andrey, Yonghong.

2) test all bpf progs in alu32 mode, from Jiong.

3) skb->sk access and bpf_sk_fullsock(), bpf_tcp_sock() helpers, from Martin.

4) support for IP encap in lwt bpf progs, from Peter.

5) remove XDP_QUERY_XSK_UMEM dead code, from Jan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

While it's understandable why kernel limits number of BTF types to 65535
and size of string section to 64KB, in libbpf as user-space library it's
too restrictive. E.g., pahole converting DWARF to BTF type information
for Linux kernel generates more than 3 million BTF types and more than
3MB of strings, before deduplication. So to allow btf__dedup() to do its
work, we need to be able to load bigger BTF sections using btf__new().
Singed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

As requested by David Ahern:

- add negative tests (no routes, explicitly unreachable destinations)
  to exercize error handling code paths;
- do not exit on test failures, but instead print a summary of
  passed/failed tests at the end.

Future patches will add TSO and VRF tests.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

In dwmac4_wrback_get_rx_timestamp_status we looking for a RX timestamp.
For that receive descriptors are handled and so we should use defines
related to receive descriptors. It'll no change the functional behavior
as RDES3_RDES1_VALID=TDES3_RS1V=BIT(26) but it makes code easier to read.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's confusing to call PTR_ERR(v).  The PTR_ERR() function is basically
a fancy cast to long so it makes you wonder, was IS_ERR() intended?  But
that doesn't make sense because vcc_walk() doesn't return error
pointers.

This patch doesn't affect runtime, it's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SO_SNDBUF and SO_RCVBUF (and their *BUFFORCE version) may overflow or
underflow their input value. This patch aims at providing explicit
handling of these extreme cases, to get a clear behaviour even with
values bigger than INT_MAX / 2 or lower than INT_MIN / 2.

For simplicity, only SO_SNDBUF and SO_SNDBUFFORCE are described here,
but the same explanation and fix apply to SO_RCVBUF and SO_RCVBUFFORCE
(with 'SNDBUF' replaced by 'RCVBUF' and 'wmem_max' by 'rmem_max').

Overflow of positive values

===========================

When handling SO_SNDBUF or SO_SNDBUFFORCE, if 'val' exceeds
INT_MAX / 2, the buffer size is set to its minimum value because
'val * 2' overflows, and max_t() considers that it's smaller than
SOCK_MIN_SNDBUF. For SO_SNDBUF, this can only happen with
net.core.wmem_max > INT_MAX / 2.

SO_SNDBUF and SO_SNDBUFFORCE are actually designed to let users probe
for the maximum buffer size by setting an arbitrary large number that
gets capped to the maximum allowed/possible size. Having the upper
half of the positive integer space to potentially reduce the buffer
size to its minimum value defeats this purpose.

This patch caps the base value to INT_MAX / 2, so that bigger values
don't overflow and keep setting the buffer size to its maximum.

Underflow of negative values
============================

For negative numbers, SO_SNDBUF always considers them bigger than
net.core.wmem_max, which is bounded by [SOCK_MIN_SNDBUF, INT_MAX].
Therefore such values are set to net.core.wmem_max and we're back to
the behaviour of positive integers described above (return maximum
buffer size if wmem_max <= INT_MAX / 2, return SOCK_MIN_SNDBUF
otherwise).

However, SO_SNDBUFFORCE behaves differently. The user value is
directly multiplied by two and compared with SOCK_MIN_SNDBUF. If
'val * 2' doesn't underflow or if it underflows to a value smaller
than SOCK_MIN_SNDBUF then buffer size is set to its minimum value.
Otherwise the buffer size is set to the underflowed value.

This patch treats negative values passed to SO_SNDBUFFORCE as null, to
prevent underflows. Therefore negative values now always set the buffer
size to its minimum value.

Even though SO_SNDBUF behaves inconsistently by setting buffer size to
the maximum value when passed a negative number, no attempt is made to
modify this behaviour. There may exist some programs that rely on using
negative numbers to set the maximum buffer size. Avoiding overflows
because of extreme net.core.wmem_max values is the most we can do here.

Summary of altered behaviours
=============================

val      : user-space value passed to setsockopt()
val_uf   : the underflowed value resulting from doubling val when
           val < INT_MIN / 2
wmem_max : short for net.core.wmem_max
val_cap  : min(val, wmem_max)
min_len  : minimal buffer length (that is, SOCK_MIN_SNDBUF)
max_len  : maximal possible buffer length, regardless of wmem_max (that
           is, INT_MAX - 1)
^^^^     : altered behaviour

SO_SNDBUF:
+-------------------------+-------------+------------+----------------+
|       CONDITION         | OLD RESULT  | NEW RESULT |    COMMENT     |
+-------------------------+-------------+------------+----------------+
| val < 0 &&              |             |            | No overflow,   |
| wmem_max <= INT_MAX/2   | wmem_max*2  | wmem_max*2 | keep original  |
|                         |             |            | behaviour      |
+-------------------------+-------------+------------+----------------+
| val < 0 &&              |             |            | Cap wmem_max   |
| INT_MAX/2 < wmem_max    | min_len     | max_len    | to prevent     |
|                         |             | ^^^^^^^    | overflow       |
+-------------------------+-------------+------------+----------------+
| 0 <= val <= min_len/2   | min_len     | min_len    | Ordinary case  |
+-------------------------+-------------+------------+----------------+
| min_len/2 < val &&      | val_cap*2   | val_cap*2  | Ordinary case  |
| val_cap <= INT_MAX/2    |             |            |                |
+-------------------------+-------------+------------+----------------+
| min_len < val &&        |             |            | Cap val_cap    |
| INT_MAX/2 < val_cap     | min_len     | max_len    | again to       |
| (implies that           |             | ^^^^^^^    | prevent        |
| INT_MAX/2 < wmem_max)   |             |            | overflow       |
+-------------------------+-------------+------------+----------------+

SO_SNDBUFFORCE:
+------------------------------+---------+---------+------------------+
|          CONDITION           | BEFORE  | AFTER   |     COMMENT      |
|                              | PATCH   | PATCH   |                  |
+------------------------------+---------+---------+------------------+
| val < INT_MIN/2 &&           | min_len | min_len | Underflow with   |
| val_uf <= min_len            |         |         | no consequence   |
+------------------------------+---------+---------+------------------+
| val < INT_MIN/2 &&           | val_uf  | min_len | Set val to 0 to  |
| val_uf > min_len             |         | ^^^^^^^ | avoid underflow  |
+------------------------------+---------+---------+------------------+
| INT_MIN/2 <= val < 0         | min_len | min_len | No underflow     |
+------------------------------+---------+---------+------------------+
| 0 <= val <= min_len/2        | min_len | min_len | Ordinary case    |
+------------------------------+---------+---------+------------------+
| min_len/2 < val <= INT_MAX/2 | val*2   | val*2   | Ordinary case    |
+------------------------------+---------+---------+------------------+
| INT_MAX/2 < val              | min_len | max_len | Cap val to       |
|                              |         | ^^^^^^^ | prevent overflow |
+------------------------------+---------+---------+------------------+
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Support Mellanox BlueField SmartNIC (mlx5-updates-2019-02-15)

Bodong Wang says,

BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:

- SEPARATED_HOST: ARM processors as a separated and orthogonal host
  like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
  external hosts virtualization model.

While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.

On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
  traffic by default. It also should perform ENABLE_HCA for the host
  PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
  store various contexts for itself, the PF and VFs belong the
  e-switch it manages.

The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.

The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2019-02-15

please apply a few more qeth patches to net-next. Along with some smaller
improvements, this revamps our code for the SW statistics that are exposed
through ETHTOOL_GSTATS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than special-casing OSN in a number of places, just give this
device type its own netdev_ops structure.

When setting up the OSN net_device, also skip the handling of the
various HW offloads (eg TSO). The device shouldn't be advertising any of
them, and the OSN code paths in qeth don't have support for them.
In particular RX VLAN filtering is not supported, so don't hook up those
callbacks in the netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement a trivial callback that exposes the queue sizes.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accumulate per-TX queue statistics, and increase their size to 64 bit.
Don't bother with enabling/disabling the statistics, the overhead is
negligible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of this is self-contained code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Counting the number of function calls and the time spent in functions
is best left to proper tracing facilities.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth dynamically allocates an array for storing pointers to its
Output Queue structures. Switch this to a static array - we are
currently limited to 4 Output Queues, so shrinking the qeth_qdio_info
struct by just a few bytes doesn't justify the additional complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once a qeth ccwgroup device is set online, it's also armed for internal
recovery. So allow for testing that code path via sysfs, regardless of
whether the interface is up or down.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the forwarding selftests to work, we need network namespaces when
using veth/vrf otherwise ping/ping6 commands like these:

ip vrf exec vveth0 /bin/ping 192.0.2.2 -c 10 -i 0.1 -w 5

will fail because network namespaces may not be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rt6_cache_allowed_for_pmtu() checks for rt->from presence, but
it does not access the RCU protected pointer. We can use
rcu_access_pointer() and clean-up the code a bit. No functional
changes intended.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in several dev_err messages, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the e-switch driver requires going to legacy mode before
changing to the offloads mode. This makes sense for regular case as
the legacy mode is done by creating VFs.

However, it's problematic when ECPF is the eswitch manager. In such
case, ECPF will control the vports on peer host including the peer
PF and VFs. But ECPF doesn't need and shall not create VFs as the
VFs are created in the peer PF host.

Grant ECPF the ability to change from none to the offloads mode. Note
that currently the only way to go back to none mode is by unloading
the ECPF driver.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>