Drop the unnecessary error messages after every spmi regmap access,
which are not expected to fail.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-3-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Make sure to disable the alarm before updating the four alarm time
registers to avoid spurious alarms during the update.

Note that the disable needs to be done outside of the ctrl_reg_lock
section to prevent a racing alarm interrupt from disabling the newly set
alarm when the lock is released.

Fixes: 9a9a54ad ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Cc: stable@vger.kernel.org      # 3.1
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-2-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Convert Amlogic Meson vrtc controller binding to yaml.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/d820d54b-d082-589a-621f-2795d885696a@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

RTC core never calls rv8803_set_alarm with an invalid alarm time,
so if an invalid alarm time > 0 is set, external factors must have
corrupted the RTC's alarm time and possibly other registers.

Play it safe by marking the date/time invalid, so all registers are
reinitialized on a ->set_time.

This may cause existing setups to lose time if they so far set only
date/time, but ignored that the alarm registers had an invalid date
value, e.g.:

  rtc rtc0: invalid alarm value: 2020-3-27 7:82:0

These systems will have their ->get_time return -EINVAL till
->set_time initializes the alarm value (and sets a new time).
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221123095527.2771434-3-s.hauer@pengutronix.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

bcd2bin(0x0A) happily returns 10, despite this being an invalid BCD
value. RTC drivers converting possibly corrupted BCD timestamps might
want to validate their input before calling bcd2bin().

Provide a macro to do so. Unlike bcd2bin and bin2bcd, out-of-line
versions are not implemented. Should the macro experience enough use,
this can be retrofitted.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221123095527.2771434-2-s.hauer@pengutronix.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

rtc-max8907 is a platform driver that doesn't use any symbol provided in
<linux/i2c.h>. So drop the include.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221219081440.1399791-1-u.kleine-koenig@pengutronix.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-1-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-12-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-11-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-10-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-9-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-8-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-7-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-6-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-5-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-4-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-3-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-2-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

pca/pcf2129 devices can also have the 'reset-source' property, so
remove them from the trivial RTC devices list.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221220152237.1125178-1-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The wake interrupt only fires when the system is in a suspend
state. Fortunately we have another interrupt that fires in a
non-suspend state at the L2 controller UPG_AUX_AON. Add support
for this interrupt line so we can use the alarm in a non-wake
context.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230124201430.2502371-3-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

A second interrupt can optionally be specified for this device
to be used for generating RTC alarm interrupts.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230124201430.2502371-2-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

On all variants of the hardware, the internal oscillator is one possible
parent for the AR100 clock. It needs to be exported so we can model that
relationship correctly in the devicetree.

Fixes: c56afc18 ("rtc: sun6i: Expose internal oscillator through device tree")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221229215319.14145-1-samuel@sholland.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Move RV3028 RTC bindings from trivial-rtc.yaml into microcrystal,rv3032.yaml.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230111163404.3526248-2-w.egorov@phytec.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Document the binding for the LS2X RTC block found on the Loongson-2K SoC
and the LS7A bridge, originally appearing on the Loongson-2H.
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/0288efeb4209e4a49af07de6399045aaa00a970c.1673227292.git.zhoubinbin@loongson.cnSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

In preparation for adding a second interrupt to service RTC
interrupts, the existing interrupt is renamed from the generic
'irq' to 'wake_irq' to more clearly convey its role.

It is also converted to an unsigned int.

Finally, the driver message that outputs the IRQ number when
registered is removed since devm_rtc_register_device() already
provides a report of registration and the interrupts can be
found in /proc/interrupts.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120190147.718976-5-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Since the WKTMR hardware block cannot be disabled it is necessary
for the driver to accommodate for associated timing hazards. This
commit targets the following possibilities:

A possible race between clearing a wktmr event and the alarm expiring
is made one-sided by setting the alarm to its maximum value before
clearing the event.

Programming alarm values close to the current time may not trigger
events if the counter advances while the alarm is being programmed.
After programming an alarm, a check is made to ensure that it is
either in the future or an expiration event is pending.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120190147.718976-4-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

These changes are not intended to affect functionality, but
simplify the source code. They are performed here to simplify
review and reduce confusion with other changes in this set.

Since set_alarm includes the alarm_irq_enable functionality call
it directly from that function for simplicity (even though it
does nothing at the moment). The order of the declarations is
changed to prevent the need for a prototype.

The function device_init_wakeup() is used to replace the
functions device_set_wakeup_capable() and device_wakeup_enable()
since it is equivalent.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120190147.718976-3-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This commit defines bit 0 as the bit of interest within the
BRCMSTB_WKTMR_EVENT register to make the implementation more
readable.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120190147.718976-2-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-561-uwe@kleine-koenig.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The current implementation of rtc-efi is expecting all the 4
time services GET{SET}_TIME{WAKEUP} must be supported by UEFI
firmware. As per the EFI_RT_PROPERTIES_TABLE, the platform
specific implementations can choose to enable selective time
services based on the RTC device capabilities.

This patch does the following changes to provide GET/SET RTC
services on platforms that do not support the WAKEUP feature.

1) Relax time services cap check when creating a platform device.
2) Clear RTC_FEATURE_ALARM bit in the absence of WAKEUP services.
3) Conditional alarm entries in '/proc/driver/rtc'.

Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Link: https://lore.kernel.org/r/20230102230630.192911-1-sdonthineni@nvidia.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown".  After a timer is set to this state, then it can no
longer be re-armed.

The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed.  It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.

This was created by using a coccinelle script and the following
commands:

    $ cat timer.cocci
    @@
    expression ptr, slab;
    identifier timer, rfield;
    @@
    (
    -       del_timer(&ptr->timer);
    +       timer_shutdown(&ptr->timer);
    |
    -       del_timer_sync(&ptr->timer);
    +       timer_shutdown_sync(&ptr->timer);
    )
      ... when strict
          when != ptr->timer
    (
            kfree_rcu(ptr, rfield);
    |
            kmem_cache_free(slab, ptr);
    |
            kfree(ptr);
    )

    $ spatch timer.cocci . > /tmp/t.patch
    $ patch -p1 < /tmp/t.patch

Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull spi fix from Mark Brown:
 "One driver specific change here which handles the case where a SPI
  device for some reason tries to change the bus speed during a message
  on fsl_spi hardware, this should be very unusual"

* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: fsl_spi: Don't change speed while chipselect is active

Merge tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "Two core fixes here, one for a long standing race which some Qualcomm
  systems have started triggering with their UFS driver and another
  fixing a problem with supply lookup introduced by the fixes for devm
  related use after free issues that were introduced in this merge
  window"

* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: fix deadlock on regulator enable
  regulator: core: Fix resolve supply lookup issue

Pull coccicheck update from Julia Lawall:
 "Modernize use of grep in coccicheck:

  Use 'grep -E' instead of 'egrep'"

* tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  scripts: coccicheck: use "grep -E" instead of "egrep"

Pull kernel hardening fixes from Kees Cook:

 - Fix CFI failure with KASAN (Sami Tolvanen)

 - Fix LKDTM + CFI under GCC 7 and 8 (Kristina Martsenko)

 - Limit CONFIG_ZERO_CALL_USED_REGS to Clang > 15.0.6 (Nathan
   Chancellor)

 - Ignore "contents" argument in LoadPin's LSM hook handling

 - Fix paste-o in /sys/kernel/warn_count API docs

 - Use READ_ONCE() consistently for oops/warn limit reading

* tag 'hardening-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  cfi: Fix CFI failure with KASAN
  exit: Use READ_ONCE() for all oops/warn limit reads
  security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
  lkdtm: cfi: Make PAC test work with GCC 7 and 8
  docs: Fix path paste-o for /sys/kernel/warn_count
  LoadPin: Ignore the "contents" argument of the LSM hooks

Pull pstore fixes from Kees Cook:

 - Switch pmsg_lock to an rt_mutex to avoid priority inversion (John
   Stultz)

 - Correctly assign mem_type property (Luca Stefani)

* tag 'pstore-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore: Properly assign mem_type property
  pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
  pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion

Pull dma-mapping fixes from Christoph Hellwig:
 "Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
  allocator, as it copes with that just as badly as the coherent
  allocator, and then add a check to make sure no one passes the flag
  ever again"

* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: reject GFP_COMP for noncoherent allocations
  ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations

Pull 9p updates from Dominique Martinet:

 - improve p9_check_errors to check buffer size instead of msize when
   possible (e.g. not zero-copy)

 - some more syzbot and KCSAN fixes

 - minor headers include cleanup

* tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux:
  9p/client: fix data race on req->status
  net/9p: fix response size check in p9_check_errors()
  net/9p: distinguish zero-copy requests
  9p/xen: do not memcpy header into req->rc
  9p: set req refcount to zero to avoid uninitialized usage
  9p/net: Remove unneeded idr.h #include
  9p/fs: Remove unneeded idr.h #include

Pull more sound updates from Takashi Iwai:
 "A few more updates for 6.2: most of changes are about ASoC
  device-specific fixes.

   - Lots of ASoC Intel AVS extensions and refactoring

   - Quirks for ASoC Intel SOF as well as regression fixes

   - ASoC Mediatek and Rockchip fixes

   - Intel HD-audio HDMI workarounds

   - Usual HD- and USB-audio device-specific quirks"

* tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
  ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
  ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
  ASoC: lochnagar: Fix unused lochnagar_of_match warning
  ASoC: Intel: Add HP Stream 8 to bytcr_rt5640.c
  ASoC: SOF: mediatek: initialize panic_info to zero
  ASoC: rt5670: Remove unbalanced pm_runtime_put()
  ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
  ASoC: Intel: soc-acpi: update codec addr on 0C11/0C4F product
  ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in rk_spdif_runtime_resume()
  ASoC: wm8994: Fix potential deadlock
  ASoC: mediatek: mt8195: add sof be ops to check audio active
  ASoC: SOF: Revert: "core: unregister clients and machine drivers in .shutdown"
  ASoC: SOF: Intel: pci-tgl: unblock S5 entry if DMA stop has failed"
  ALSA: hda/hdmi: fix stream-id config keep-alive for rt suspend
  ALSA: hda/hdmi: set default audio parameters for KAE silent-stream
  ALSA: hda/hdmi: fix i915 silent stream programming flow
  ALSA: hda: Error out if invalid stream is being setup
  ASoC: dt-bindings: fsl-sai: Reinstate i.MX93 SAI compatible string
  ASoC: soc-pcm.c: Clear DAIs parameters after stream_active is updated
  ASoC: codecs: wcd-clsh: Remove the unused function
  ...