The BBNSM module includes a real time counter with alarm.
Add a RTC driver for this function.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230215024117.3357341-3-ping.bai@nxp.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

On JZ4770 and JZ4780, the CLK32K pin is configurable. By default, it is
configured as a GPIO in input mode, and its value can be read through
GPIO PD14.

With this change, clients can now request the 32 kHz clock on the CLK32K
pin, through Device Tree. This clock is simply a pass-through of the
input oscillator's clock with enable/disable operations.

This will permit the WiFi/Bluetooth chip to work on the MIPS CI20 board,
which does source one of its clocks from the CLK32K pin.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20230129120442.22858-5-paul@crapouillou.netSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Use dev_err_probe() where it makes sense to simplify a bit the code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20230129120442.22858-4-paul@crapouillou.netSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Use readl_poll_timeout() from <iopoll.h> instead of using custom poll
loops.

The timeout settings are different, but that shouldn't be much of a
problem. Instead of polling 10000 times in a close loop, it polls for
one millisecond.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20230129120442.22858-3-paul@crapouillou.netSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The RTC in the JZ4770 is compatible with the JZ4760, but has an extra
register that permits to configure the behaviour of the CLK32K pin. The
same goes for the RTC in the JZ4780.

With this change, the RTC node is now also a clock provider on these
SoCs, so a #clock-cells property is added.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230129120442.22858-2-paul@crapouillou.netSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

MOXA ART RTC driver has been switched to gpiod API and is now using
properly named properties for its gpios (with gpiolib implementing a
quirk to recognize legacy names). Change binding document to use
proper names as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20230201054815.4112632-2-dmitry.torokhov@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Switch the driver from legacy gpio API that is deprecated to the newer
gpiod API that respects line polarities described in ACPI/DT.

This makes driver use standard property name for its gpios
("rtc-*-gpios" vs "gpios-rtc-*"), however there is a quirk in gpiolib
to also recognize legacy names and keep compatibility with older DTSes:
eaf1a296 ("gpiolib: of: add a quirk for legacy names in MOXA ART
RTC").
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20230201054815.4112632-1-dmitry.torokhov@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

For consistency with the rest of the driver, drop the last two error
messages for conditions that should only occur during development, if
ever.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-16-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Clean up local declarations somewhat by using the reverse xmas style
consistently throughout.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-15-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

In preparation for adding support for setting the time by means of an
externally stored offset, refactor read_time() by adding a new helper
that can be used to retrieve the raw time as stored in the RTC.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-14-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The PMIC RTC registers are 32-bit so explicitly use u32 rather than
unsigned long for timestamps to reflect the hardware.

This will also help avoid unintentional range extensions when adding
support for managing an external offset.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-13-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Clean up the driver comments somewhat and remove obsolete, incorrect or
redundant ones.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-12-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Clean up the driver somewhat by renaming the driver-data alarm irq
variable by dropping the redundant "rtc" prefix.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-11-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Rename the driver-data struct device pointer by dropping the "rtc"
prefix which is both redundant and misleading (as this is a pointer to
the platform device and not the rtc class device).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-10-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Clean up the time and alarm callback debugging by using a consistent and
succinct human-readable (i.e. non-raw) format.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-9-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Use the unaligned le32 helpers instead of open coding when accessing the
time and alarm registers.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-8-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Drop the original register defines which have been unused since commit
c8d523a4 ("drivers/rtc/rtc-pm8xxx.c: rework to support pm8941 rtc").
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-7-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

In the unlikely event that disabling the alarm and clearing the status
ever fails, return IRQ_NONE instead of IRQ_HANDLED.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-6-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Since commit c8d523a4 ("drivers/rtc/rtc-pm8xxx.c: rework to support
pm8941 rtc") which removed the shadow control register there is no need
for a driver lock.

Specifically, the rtc ops are serialised by rtc core and the interrupt
handler only unconditionally disables the alarm using the alarm_ctrl
register.

Note that since only the alarm enable bit of alarm_ctrl is used after
enabling the RTC at probe, the locking was not needed when doing open
coded read-modify-write cycles either.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-5-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Switch to using regmap_update_bits() instead of open coding
read-modify-write accesses.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-4-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Drop the unnecessary error messages after every spmi regmap access,
which are not expected to fail.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-3-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Make sure to disable the alarm before updating the four alarm time
registers to avoid spurious alarms during the update.

Note that the disable needs to be done outside of the ctrl_reg_lock
section to prevent a racing alarm interrupt from disabling the newly set
alarm when the lock is released.

Fixes: 9a9a54ad ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Cc: stable@vger.kernel.org      # 3.1
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-2-johan+linaro@kernel.orgSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Convert Amlogic Meson vrtc controller binding to yaml.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/d820d54b-d082-589a-621f-2795d885696a@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

RTC core never calls rv8803_set_alarm with an invalid alarm time,
so if an invalid alarm time > 0 is set, external factors must have
corrupted the RTC's alarm time and possibly other registers.

Play it safe by marking the date/time invalid, so all registers are
reinitialized on a ->set_time.

This may cause existing setups to lose time if they so far set only
date/time, but ignored that the alarm registers had an invalid date
value, e.g.:

  rtc rtc0: invalid alarm value: 2020-3-27 7:82:0

These systems will have their ->get_time return -EINVAL till
->set_time initializes the alarm value (and sets a new time).
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221123095527.2771434-3-s.hauer@pengutronix.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

bcd2bin(0x0A) happily returns 10, despite this being an invalid BCD
value. RTC drivers converting possibly corrupted BCD timestamps might
want to validate their input before calling bcd2bin().

Provide a macro to do so. Unlike bcd2bin and bin2bcd, out-of-line
versions are not implemented. Should the macro experience enough use,
this can be retrofitted.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221123095527.2771434-2-s.hauer@pengutronix.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

rtc-max8907 is a platform driver that doesn't use any symbol provided in
<linux/i2c.h>. So drop the include.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221219081440.1399791-1-u.kleine-koenig@pengutronix.deSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-1-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-12-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-11-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-10-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-9-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-8-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-7-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-6-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-5-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-4-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-3-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

Allow the IRQ type to be passed from the device tree if available as there
may be components changing the trigger type of the interrupt between the
RTC and the IRQ controller.

Link: https://lore.kernel.org/r/20230123200217.1236011-2-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

pca/pcf2129 devices can also have the 'reset-source' property, so
remove them from the trivial RTC devices list.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221220152237.1125178-1-hugo@hugovil.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

The wake interrupt only fires when the system is in a suspend
state. Fortunately we have another interrupt that fires in a
non-suspend state at the L2 controller UPG_AUX_AON. Add support
for this interrupt line so we can use the alarm in a non-wake
context.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230124201430.2502371-3-opendmb@gmail.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>