There are quite a lot simple GPIO controller which are using regmap to
access the hardware. This driver tries to be a base to unify existing
code into one place. This won't cover everything but it should be a good
starting point.

It does not implement its own irq_chip because there is already a
generic one for regmap based devices. Instead, the irq_chip will be
instantiated in the parent driver and its irq domain will be associate
to this driver.

For now it consists of the usual registers, like set (and an optional
clear) data register, an input register and direction registers.
Out-of-the-box, it supports consecutive register mappings and mappings
where the registers have gaps between them with a linear mapping between
GPIO offset and bit position. For weirder mappings the user can register
its own .xlate().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-3-michael@walle.ccSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The function connects an IRQ domain to a gpiochip and reuses
gpiochip_to_irq() which is provided by gpiolib.

gpiochip_irqchip_* and regmap_irq partially provide the same
functionality. This function will help to connect just the
minimal functionality of the gpiochip_irqchip which is needed to
work together with regmap-irq.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-2-michael@walle.ccSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

With 'commit 461c1a7d ("gpiolib: override irq_enable/disable")' gpiolib
overrides irqchip's irq_enable and irq_disable callbacks. If irq_disable
callback is implemented then genirq takes unlazy path to disable irq.

Underlying irqchip may not want to implement irq_disable callback to lazy
disable irq when client drivers invokes disable_irq(). By overriding
irq_disable callback, gpiolib ends up always unlazy disabling IRQ.

Allow gpiolib to lazy disable IRQs by overriding irq_disable callback only
if irqchip implemented irq_disable. In cases where irq_disable is not
implemented irq_mask is overridden. Similarly override irq_enable callback
only if irqchip implemented irq_enable otherwise irq_unmask is overridden.

Fixes: 461c1a7d ("gpiolib: override irq_enable/disable")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/1590253873-11556-2-git-send-email-mkshah@codeaurora.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

We already have two conditionals inside the outer one to check
if the command is GPIO_GET_LINEINFO_WATCH_IOCTL. I think it's
time to actually do what I have proposed in the first place, i.e.
to separate GPIO_GET_LINEINFO_WATCH_IOCTL from GPIO_GET_LINEINFO_IOCTL.
It's +13 LOCs, and surprisingly only +13 bytes of binary on x86_32,
but for the price of much better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200525194028.74236-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 5.7-rc7

Merge tag 'gpio-updates-for-v5.8-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel

gpio: updates for v5.8 - part 2

- fix the initialization ordering in gpio-max730x
- make gpio-pxa buildable for compile testing
- make gpio-pca953x buildable as a module

pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200522080839.32612-1-dinghao.liu@zju.edu.cnSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Perhaps by some historical reasons the IRQ support has been allowed
only for built-in driver. However, there is nothing prevents us
to build it as module an use as IRQ chip.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add COMPILE_TEST support to the PXA GPIO driver for better compile
testing coverage.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Document Device Tree bindings for the Renesas EMMA Mobile General
Purpose I/O Interface.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200519081157.29095-1-geert+renesas@glider.beSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The commit 657a06df
  ("dt-bindings: gpio: Convert snps,dw-apb-gpio to DT schema")
missed MAINTAINERS update.

Fixes: 657a06df ("dt-bindings: gpio: Convert snps,dw-apb-gpio to DT schema")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200520120955.68427-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

has_irq member of struct dwapb_port_property is used only in one place,
so, make it local test instead and remove from the structure.
This local test is using memchr_inv() which is quite efficient in comparison
to the original loop and possible little overhead can be neglected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-4-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

IRQ 0 is not valid in Linux interrupt number space.
Refactor the code with this kept in mind.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-3-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

platform_get_irq() will generate an error message if the requested IRQ
is not present. Use platform_get_irq_optional() to avoid the error message
being generated.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-2-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add missed acpi_gpiochip_free_interrupts() call when unregistering ports.

While at it, drop extra check to call acpi_gpiochip_request_interrupts().
There is no need to have an additional check to call
acpi_gpiochip_request_interrupts(). Even without any interrupts available
the registered ACPI Event handlers can be useful for debugging purposes.

Fixes: e6cb3486 ("gpio: dwapb: add gpio-signaled acpi event support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull EFI fixes from Thomas Gleixner:
 "A set of EFI fixes:

   - Don't return a garbage screen info when EFI framebuffer is not
     available

   - Make the early EFI console work properly with wider fonts instead
     of drawing garbage

   - Prevent a memory buffer leak in allocate_e820()

   - Print the firmware error record properly so it can be decoded by
     users

   - Fix a symbol clash in the host tool build which only happens with
     newer compilers.

   - Add a missing check for the event log version of TPM which caused
     boot failures on several Dell systems due to an attempt to decode
     SHA-1 format with the crypto agile algorithm"

* tag 'efi-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tpm: check event log version before reading final events
  efi: Pull up arch-specific prototype efi_systab_show_arch()
  x86/boot: Mark global variables as static
  efi: cper: Add support for printing Firmware Error Record Reference
  efi/libstub/x86: Avoid EFI map buffer alloc in allocate_e820()
  efi/earlycon: Fix early printk for wider fonts
  efi/libstub: Avoid returning uninitialized data from setup_graphics()

Pull x86 fixes from Thomas Gleixner:
 "Two fixes for x86:

   - Unbreak stack dumps for inactive tasks by interpreting the special
     first frame left by __switch_to_asm() correctly.

     The recent change not to skip the first frame so ORC and frame
     unwinder behave in the same way caused all entries to be
     unreliable, i.e. prepended with '?'.

   - Use cpumask_available() instead of an implicit NULL check of a
     cpumask_var_t in mmio trace to prevent a Clang build warning"

* tag 'x86-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks
  x86/mmiotrace: Use cpumask_available() for cpumask_var_t variables

Pull scheduler fixes from Thomas Gleixner:
 "A set of fixes for the scheduler:

   - Fix handling of throttled parents in enqueue_task_fair() completely.

     The recent fix overlooked a corner case where the first iteration
     terminates due to an entity already being on the runqueue which
     makes the list management incomplete and later triggers the
     assertion which checks for completeness.

   - Fix a similar problem in unthrottle_cfs_rq().

   - Show the correct uclamp values in procfs which prints the effective
     value twice instead of requested and effective"

* tag 'sched-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix unthrottle_cfs_rq() for leaf_cfs_rq list
  sched/debug: Fix requested task uclamp values shown in procfs
  sched/fair: Fix enqueue_task_fair() warning some more

Pull networking fixes from David Miller:

 1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna
    Bhowmik.

 2) Nexthop attributes aren't being checked properly because of
    mis-initialized iterator, from David Ahern.

 3) Revert iop_idents_reserve() change as it caused performance
    regressions and was just working around what is really a UBSAN bug
    in the compiler. From Yuqi Jin.

 4) Read MAC address properly from ROM in bmac driver (double iteration
    proceeds past end of address array), from Jeremy Kerr.

 5) Add Microsoft Surface device IDs to r8152, from Marc Payne.

 6) Prevent reference to freed SKB in __netif_receive_skb_core(), from
    Boris Sukholitko.

 7) Fix ACK discard behavior in rxrpc, from David Howells.

 8) Preserve flow hash across packet scrubbing in wireguard, from Jason
    A. Donenfeld.

 9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric
    Dumazet.

10) Fix encryption error checking in kTLS code, from Vadim Fedorenko.

11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki.

12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet.

13) Fix use after free in mlxsw driver, from Jiri Pirko.

14) Order kTLS key destruction properly in mlx5 driver, from Tariq
    Toukan.

15) Check devm_platform_ioremap_resource() return value properly in
    several drivers, from Tiezhu Yang.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
  net: smsc911x: Fix runtime PM imbalance on error
  net/mlx4_core: fix a memory leak bug.
  net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
  net: phy: mscc: fix initialization of the MACsec protocol mode
  net: stmmac: don't attach interface until resume finishes
  net: Fix return value about devm_platform_ioremap_resource()
  net/mlx5: Fix error flow in case of function_setup failure
  net/mlx5e: CT: Correctly get flow rule
  net/mlx5e: Update netdev txq on completions during closure
  net/mlx5: Annotate mutex destroy for root ns
  net/mlx5: Don't maintain a case of del_sw_func being null
  net/mlx5: Fix cleaning unmanaged flow tables
  net/mlx5: Fix memory leak in mlx5_events_init
  net/mlx5e: Fix inner tirs handling
  net/mlx5e: kTLS, Destroy key object after destroying the TIS
  net/mlx5e: Fix allowed tc redirect merged eswitch offload cases
  net/mlx5: Avoid processing commands before cmdif is ready
  net/mlx5: Fix a race when moving command interface to events mode
  net/mlx5: Add command entry handling completion
  rxrpc: Fix a memory leak in rxkad_verify_response()
  ...

Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes 2020-05-22

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.13
   ('net/mlx5: Add command entry handling completion')

For -stable v5.2
   ('net/mlx5: Fix error flow in case of function_setup failure')
   ('net/mlx5: Fix memory leak in mlx5_events_init')

For -stable v5.3
   ('net/mlx5e: Update netdev txq on completions during closure')
   ('net/mlx5e: kTLS, Destroy key object after destroying the TIS')
   ('net/mlx5e: Fix inner tirs handling')

For -stable v5.6
   ('net/mlx5: Fix cleaning unmanaged flow tables')
   ('net/mlx5: Fix a race when moving command interface to events mode')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.

Fixes: fe6f700d ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
  cpsw_suspend()
  |- cpsw_ndo_stop()
    |- __hw_addr_ref_unsync_dev()
      |- cpsw_purge_all_mc()
         |- vlan_for_each()
            |- ASSERT_RTNL();

Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.

Fixes: 15180eca ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.

Fixes: 1bbe0ecc ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 14b41a29 ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.

Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized.  Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce().  timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().

  systemd--1995    2.... 552950018us : stmmac_suspend: 4994
  ksoftirq-9       0..s2 553123133us : stmmac_tx_timer_arm: 2276
  systemd--1995    0.... 553127896us : stmmac_resume: 5101
  systemd--320     7...2 553132752us : stmmac_tx_timer_arm: 2276
  (sd-exec-1999    5...2 553135204us : stmmac_tx_timer_arm: 2276
  ---------------------------------
  pc : run_timer_softirq+0x468/0x5e0
  lr : run_timer_softirq+0x570/0x5e0
  Call trace:
   run_timer_softirq+0x468/0x5e0
   __do_softirq+0x124/0x398
   irq_exit+0xd8/0xe0
   __handle_domain_irq+0x6c/0xc0
   gic_handle_irq+0x60/0xb0
   el1_irq+0xb8/0x180
   arch_cpu_idle+0x38/0x230
   default_idle_call+0x24/0x3c
   do_idle+0x1e0/0x2b8
   cpu_startup_entry+0x28/0x48
   secondary_start_kernel+0x1b4/0x208

Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The srmmu_nocache_init() uses __nocache_fix() macro to add an offset to
page table entry to access srmmu_nocache_pool.

But since sparc32 has only three actual page table levels, pgd, p4d and
pud are essentially the same thing and pgd_offset() and p4d_offset() are
no-ops, the __nocache_fix() should be done only at PUD level.

Remove __nocache_fix() for p4d_offset() and pud_offset() and keep it
only for PUD and lower levels.

Fixes: c2bc26f7 ("sparc32: use PUD rather than PGD to get PMD in srmmu_nocache_init()")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Anatoly Pugachev <matorola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge misc fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  MAINTAINERS: add files related to kdump
  z3fold: fix use-after-free when freeing handles
  sparc32: use PUD rather than PGD to get PMD in srmmu_nocache_init()
  MAINTAINERS: update email address for Naoya Horiguchi
  sh: include linux/time_types.h for sockios
  kasan: disable branch tracing for core runtime
  selftests/vm/write_to_hugetlbfs.c: fix unused variable warning
  selftests/vm/.gitignore: add mremap_dontunmap
  rapidio: fix an error in get_user_pages_fast() error handling
  x86: bitops: fix build regression
  device-dax: don't leak kernel memory to user space after unloading kmem

Pull driver core fixes from Greg KH:
 "So, turns out the kobject fix didn't quite work, so here are four
  patches that in the end, result in just two driver core fixes for
  reported issues that no one has had problems with.

  The kobject patch that was originally in here has now been reverted,
  as Guenter reported boot problems with it on some of his systems"

* tag 'driver-core-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Revert "kobject: Make sure the parent does not get released before its children"
  kobject: Make sure the parent does not get released before its children
  driver core: Fix handling of SYNC_STATE_ONLY + STATELESS device links
  driver core: Fix SYNC_STATE_ONLY device link implementation

Pull char/misc fixes from Greg KH:
 "Here are some small char/misc driver fixes for 5.7-rc7 that resolve
  some reported issues. Included in here are tiny fixes for the mei,
  coresight, rtsx, ipack, and mhi drivers.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  misc: rtsx: Add short delay after exit from ASPM
  bus: mhi: core: Fix some error return code
  ipack: tpci200: fix error return code in tpci200_register()
  coresight: cti: remove incorrect NULL return check
  mei: release me_cl object reference

Pull staging/iio fixes from Greg KH:
 "Here are some small staging and IIO driver fixes for 5.7-rc7

  Nothing major, just a collection of IIO driver fixes for reported
  issues, and a few small staging driver fixes that people have found.
  Full details are in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: wfx: unlock on error path
  staging: greybus: Fix uninitialized scalar variable
  staging: kpc2000: fix error return code in kp2000_pcie_probe()
  iio: sca3000: Remove an erroneous 'get_device()'
  iio: adc: stm32-dfsdm: fix device used to request dma
  iio: adc: stm32-adc: fix device used to request dma
  iio: adc: ti-ads8344: Fix channel selection
  staging: iio: ad2s1210: Fix SPI reading
  iio: dac: vf610: Fix an error handling path in 'vf610_dac_probe()'
  iio: imu: st_lsm6dsx: unlock on error in st_lsm6dsx_shub_write_raw()
  iio: chemical: atlas-sensor: correct DO-SM channels

Pull tty/serial fix from Greg KH:
 "Here is a single serial driver fix for 5.7-rc7. It resolves an issue
  with the SiFive serial console init sequence that was reported a
  number of times.

  It has been in linux-next for a while now with no reported issues"

* tag 'tty-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: add missing spin_lock_init for SiFive serial console

Pull s390 fixes from Vasily Gorbik:

 - Add missing R_390_JMP_SLOT relocation type in KASLR code.

 - Fix set_huge_pte_at for empty ptes issue which has been uncovered
   with arch page table helper tests.

 - Correct initrd location for kdump kernel.

 - Fix s390_mmio_read/write with MIO in PCI code.

* tag 's390-5.7-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/kaslr: add support for R_390_JMP_SLOT relocation type
  s390/mm: fix set_huge_pte_at() for empty ptes
  s390/kexec_file: fix initrd location for kdump kernel
  s390/pci: Fix s390_mmio_read/write with MIO

Kdump is implemented based on kexec, however some files are only related
to crash dumping and missing, add them to KDUMP entry.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Dave Young <dyoung@redhat.com>
Link: http://lkml.kernel.org/r/20200520103633.GW5029@MiWiFi-R3L-srvSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

free_handle() for a foreign handle may race with inter-page compaction,
what can lead to memory corruption.

To avoid that, take write lock not read lock in free_handle to be
synchronized with __release_z3fold_page().

For example KASAN can detect it:

  ==================================================================
  BUG: KASAN: use-after-free in LZ4_decompress_safe+0x2c4/0x3b8
  Read of size 1 at addr ffffffc976695ca3 by task GoogleApiHandle/4121

  CPU: 0 PID: 4121 Comm: GoogleApiHandle Tainted: P S         OE     4.19.81-perf+ #162
  Hardware name: Sony Mobile Communications. PDX-203(KONA) (DT)
  Call trace:
     LZ4_decompress_safe+0x2c4/0x3b8
     lz4_decompress_crypto+0x3c/0x70
     crypto_decompress+0x58/0x70
     zcomp_decompress+0xd4/0x120
     ...

Apart from that, initialize zhdr->mapped_count in init_z3fold_page() and
remove "newpage" variable because it is not used anywhere.
Signed-off-by: Uladzislau Rezki <uladzislau.rezki@sony.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Raymond Jennings <shentino@gmail.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200520082100.28876-1-vitaly.wool@konsulko.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kbuild test robot reported the following warning:

  arch/sparc/mm/srmmu.c: In function 'srmmu_nocache_init': arch/sparc/mm/srmmu.c:300:9: error: variable 'pud' set but not used [-Werror=unused-but-set-variable]
  300 |  pud_t *pud;

This warning is caused by misprint in the page table traversal in
srmmu_nocache_init() function which accessed a PMD entry using PGD
rather than PUD.

Since sparc32 has only 3 page table levels, the PGD and PUD are
essentially the same and usage of __nocache_fix() removed the type
checking.

Use PUD for the consistency and to silence the compiler warning.

Fixes: 7235db26 ("sparc32: use pgtable-nopud instead of 4level-fixup")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Anatoly Pugachev <matorola@gmail.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200520132005.GM1059226@linux.ibm.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

My email address has changed due to system upgrade, so please update it
in MAINTAINERS list.  My old address (n-horiguchi@ah.jp.nec.com) will be
still active for a few months.

Note that my email system has some encoding issue and can't send patches
in raw format via git-send-email.  So patches from me will be delivered
via my free address (nao.horiguchi@gmail.com) or GitHub.
Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1589874488-9247-1-git-send-email-naoya.horiguchi@nec.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Using the socket ioctls on arch/sh (and only there) causes build time
problems when __kernel_old_timeval/__kernel_old_timespec are not already
visible to the compiler.

Add an explict include line for the header that defines these
structures.

Fixes: 8c709f9a ("y2038: sh: remove timeval/timespec usage from headers")
Fixes: 0768e170 ("net: socket: implement 64-bit timestamps")
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200519131327.1836482-1-arnd@arndb.deSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

During early boot, while KASAN is not yet initialized, it is possible to
enter reporting code-path and end up in kasan_report().

While uninitialized, the branch there prevents generating any reports,
however, under certain circumstances when branches are being traced
(TRACE_BRANCH_PROFILING), we may recurse deep enough to cause kernel
reboots without warning.

To prevent similar issues in future, we should disable branch tracing
for the core runtime.

[elver@google.com: remove duplicate DISABLE_BRANCH_PROFILING, per Qian Cai]
  Link: https://lore.kernel.org/lkml/20200517011732.GE24705@shao2-debian/
  Link: http://lkml.kernel.org/r/20200522075207.157349-1-elver@google.comReported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Qian Cai <cai@lca.pw>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r//20200517011732.GE24705@shao2-debian/
Link: http://lkml.kernel.org/r/20200519182459.87166-1-elver@google.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>