- 29 Dec, 2018 33 commits
-
-
Richard Weinberger authored
commit e58725d5 upstream. UBIFS's recovery code strictly assumes that a deleted inode will never come back, therefore it removes all data which belongs to that inode as soon it faces an inode with link count 0 in the replay list. Before O_TMPFILE this assumption was perfectly fine. With O_TMPFILE it can lead to data loss upon a power-cut. Consider a journal with entries like: 0: inode X (nlink = 0) /* O_TMPFILE was created */ 1: data for inode X /* Someone writes to the temp file */ 2: inode X (nlink = 0) /* inode was changed, xattr, chmod, … */ 3: inode X (nlink = 1) /* inode was re-linked via linkat() */ Upon replay of entry #2 UBIFS will drop all data that belongs to inode X, this will lead to an empty file after mounting. As solution for this problem, scan the replay list for a re-link entry before dropping data. Fixes: 474b9370 ("ubifs: Implement O_TMPFILE") Cc: stable@vger.kernel.org # 4.9-4.18 Cc: Russell Senior <russell@personaltelco.net> Cc: Rafał Miłecki <zajec5@gmail.com> Reported-by:
Russell Senior <russell@personaltelco.net> Reported-by:
Rafał Miłecki <zajec5@gmail.com> Tested-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
Richard Weinberger <richard@nod.at> [rmilecki: update ubifs_assert() calls to compile with 4.18 and older] Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Uwe Kleine-König authored
The relevant difference between prepare_message and config is that the former is run before the CS signal is asserted. So the polarity of the CLK line must be configured in prepare_message as an edge generated by config might already result in a latch of the MOSI line. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Mark Brown <broonie@kernel.org> [ukleinek: backport to v4.14.x] Signed-off-by:
-
Uwe Kleine-König authored
This is just preparatory work which allows to move some initialisation that currently is done in the per transfer hook .config to an earlier point in time in the next few patches. There is no change in behaviour introduced by this patch. Signed-off-by:
-
Ihab Zhaika authored
commit f108703c upstream. add few PCI ID'S for 9560, 9462, 9461 and killer series. Cc: stable@vger.kernel.org Signed-off-by:
Ihab Zhaika <ihab.zhaika@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Emmanuel Grumbach authored
commit eca1e56c upstream. Old firmware versions don't support this command. Sending it to any firmware before -41.ucode will crash the firmware. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201975 Fixes: 66e83903 ("iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE") CC: <stable@vger.kernel.org> #4.19+ Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Sergey Senozhatsky authored
commit c7c3f05e upstream. From printk()/serial console point of view panic() is special, because it may force CPU to re-enter printk() or/and serial console driver. Therefore, some of serial consoles drivers are re-entrant. E.g. 8250: serial8250_console_write() { if (port->sysrq) locked = 0; else if (oops_in_progress) locked = spin_trylock_irqsave(&port->lock, flags); else spin_lock_irqsave(&port->lock, flags); ... } panic() does set oops_in_progress via bust_spinlocks(1), so in theory we should be able to re-enter serial console driver from panic(): CPU0 <NMI> uart_console_write() serial8250_console_write() // if (oops_in_progress) // spin_trylock_irqsave() call_console_drivers() console_unlock() console_flush_on_panic() bust_spinlocks(1) // oops_in_progress++ panic() <NMI/> spin_lock_irqsave(&port->lock, flags) // spin_lock_irqsave() serial8250_console_write() call_console_drivers() console_unlock() printk() ... However, this does not happen and we deadlock in serial console on port->lock spinlock. And the problem is that console_flush_on_panic() called after bust_spinlocks(0): void panic(const char *fmt, ...) { bust_spinlocks(1); ... bust_spinlocks(0); console_flush_on_panic(); ... } bust_spinlocks(0) decrements oops_in_progress, so oops_in_progress can go back to zero. Thus even re-entrant console drivers will simply spin on port->lock spinlock. Given that port->lock may already be locked either by a stopped CPU, or by the very same CPU we execute panic() on (for instance, NMI panic() on printing CPU) the system deadlocks and does not reboot. Fix this by removing bust_spinlocks(0), so oops_in_progress is always set in panic() now and, thus, re-entrant console drivers will trylock the port->lock instead of spinning on it forever, when we call them from console_flush_on_panic(). Link: http://lkml.kernel.org/r/20181025101036.6823-1-sergey.senozhatsky@gmail.com Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Daniel Wang <wonderfly@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Feiner <pfeiner@google.com> Cc: linux-serial@vger.kernel.org Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by:
Petr Mladek <pmladek@suse.com> Signed-off-by:
-
Colin Ian King authored
commit 32043fa0 upstream. Currently the copy_to_user of data in the gentry struct is copying uninitiaized data in field _pad from the stack to userspace. Fix this by explicitly memset'ing gentry to zero, this also will zero any compiler added padding fields that may be in struct (currently there are none). Detected by CoverityScan, CID#200783 ("Uninitialized scalar variable") Fixes: b263b31e ("x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Tyler Hicks <tyhicks@canonical.com> Cc: security@kernel.org Link: https://lkml.kernel.org/r/20181218172956.1440-1-colin.king@canonical.comSigned-off-by:
-
Dexuan Cui authored
commit fc96df16 upstream. Before 98f4c651, we returned zeros for unopened channels. With 98f4c651, we started to return random on-stack values. We'd better return -EINVAL instead. Fixes: 98f4c651 ("hv: move ringbuffer bus attributes to dev_groups") Cc: stable@vger.kernel.org Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
Dexuan Cui <decui@microsoft.com> Signed-off-by:
-
Cfir Cohen authored
commit c2dd5146 upstream. nested_get_vmcs12_pages() processes the posted_intr address in vmcs12. It caches the kmap()ed page object and pointer, however, it doesn't handle errors correctly: it's possible to cache a valid pointer, then release the page and later dereference the dangling pointer. I was able to reproduce with the following steps: 1. Call vmlaunch with valid posted_intr_desc_addr but an invalid MSR_EFER. This causes nested_get_vmcs12_pages() to cache the kmap()ed pi_desc_page and pi_desc. Later the invalid EFER value fails check_vmentry_postreqs() which fails the first vmlaunch. 2. Call vmlanuch with a valid EFER but an invalid posted_intr_desc_addr (I set it to 2G - 0x80). The second time we call nested_get_vmcs12_pages pi_desc_page is unmapped and released and pi_desc_page is set to NULL (the "shouldn't happen" clause). Due to the invalid posted_intr_desc_addr, kvm_vcpu_gpa_to_page() fails and nested_get_vmcs12_pages() returns. It doesn't return an error value so vmlaunch proceeds. Note that at this time we have a dangling pointer in vmx->nested.pi_desc and POSTED_INTR_DESC_ADDR in L0's vmcs. 3. Issue an IPI in L2 guest code. This triggers a call to vmx_complete_nested_posted_interrupt() and pi_test_and_clear_on() which dereferences the dangling pointer. Vulnerable code requires nested and enable_apicv variables to be set to true. The host CPU must also support posted interrupts. Fixes: 5e2f30b7 "KVM: nVMX: get rid of nested_get_page()" Cc: stable@vger.kernel.org Reviewed-by:
Andy Honig <ahonig@google.com> Signed-off-by:
Cfir Cohen <cfir@google.com> Reviewed-by:
Liran Alon <liran.alon@oracle.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Eduardo Habkost authored
commit 0e1b869f upstream. Some guests OSes (including Windows 10) write to MSR 0xc001102c on some cases (possibly while trying to apply a CPU errata). Make KVM ignore reads and writes to that MSR, so the guest won't crash. The MSR is documented as "Execution Unit Configuration (EX_CFG)", at AMD's "BIOS and Kernel Developer's Guide (BKDG) for AMD Family 15h Models 00h-0Fh Processors". Cc: stable@vger.kernel.org Signed-off-by:
Eduardo Habkost <ehabkost@redhat.com> Signed-off-by:
-
Thomas Gleixner authored
commit 0e334db6 upstream. The signal delivery path of posix-timers can try to rearm the timer even if the interval is zero. That's handled for the common case (hrtimer) but not for alarm timers. In that case the forwarding function raises a division by zero exception. The handling for hrtimer based posix timers is wrong because it marks the timer as active despite the fact that it is stopped. Move the check from common_hrtimer_rearm() to posixtimer_rearm() to cure both issues. Reported-by: syzbot+9d38bedac9cc77b8ad5e@syzkaller.appspotmail.com Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit e59f5e08 upstream. Commit 78d3a92e ("gpiolib-acpi: Register GpioInt ACPI event handlers from a late_initcall") deferred the entire acpi_gpiochip_request_interrupt call for each event resource. This means it also delays the gpiochip_request_own_desc(..., "ACPI:Event") call. This is a problem if some AML code reads the GPIO pin before we run the deferred acpi_gpiochip_request_interrupt, because in that case acpi_gpio_adr_space_handler() will already have called gpiochip_request_own_desc(..., "ACPI:OpRegion") causing the call from acpi_gpiochip_request_interrupt to fail with -EBUSY and we will fail to register an event handler. acpi_gpio_adr_space_handler is prepared for acpi_gpiochip_request_interrupt already having claimed the pin, but the other way around does not work. One example of a problem this causes, is the event handler for the OTG ID pin on a Prowise PT301 tablet not registering, keeping the port stuck in whatever mode it was in during boot and e.g. only allowing charging after a reboot. This commit fixes this by only deferring the request_irq call and the initial run of edge-triggered IRQs instead of deferring all of acpi_gpiochip_request_interrupt. Cc: stable@vger.kernel.org Fixes: 78d3a92e ("gpiolib-acpi: Register GpioInt ACPI event ...") Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Christophe Leroy authored
commit abf221d2 upstream. spi_read() and spi_write() require DMA-safe memory. When CONFIG_VMAP_STACK is selected, those functions cannot be used with buffers on stack. This patch replaces calls to spi_read() and spi_write() by spi_write_then_read() which doesn't require DMA-safe buffers. Fixes: 0c36ec31 ("gpio: gpio driver for max7301 SPI GPIO expander") Cc: <stable@vger.kernel.org> Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Russell King authored
commit 0b479790 upstream. While booting with rootfs on MMC, the following warning is encountered on OMAP4430: omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536] This is because the DMA engine has a default maximum segment size of 64K but HSMMC sets: mmc->max_blk_size = 512; /* Block Length at max can be 1024 */ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; mmc->max_seg_size = mmc->max_req_size; which ends up telling the block layer that we support a maximum segment size of 65535*512, which exceeds the advertised DMA engine capabilities. Fix this by clamping the maximum segment size to the lower of the maximum request size and of the DMA engine device used for either DMA channel. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Ulf Hansson authored
commit e3ae3401 upstream. Some eMMCs from Micron have been reported to need ~800 ms timeout, while enabling the CACHE ctrl after running sudden power failure tests. The needed timeout is greater than what the card specifies as its generic CMD6 timeout, through the EXT_CSD register, hence the problem. Normally we would introduce a card quirk to extend the timeout for these specific Micron cards. However, due to the rather complicated debug process needed to find out the error, let's simply use a minimum timeout of 1600ms, the double of what has been reported, for all cards when enabling CACHE ctrl. Reported-by:
Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reported-by:
Andreas Dannenberg <dannenberg@ti.com> Reported-by:
Faiz Abbas <faiz_abbas@ti.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ulf Hansson authored
commit ba9f39a7 upstream. In commit 5320226a ("mmc: core: Disable HPI for certain Hynix eMMC cards"), then intent was to prevent HPI from being used for some eMMC cards, which didn't properly support it. However, that went too far, as even BKOPS and CACHE ctrl became prevented. Let's restore those parts and allow BKOPS and CACHE ctrl even if HPI isn't supported. Fixes: 5320226a ("mmc: core: Disable HPI for certain Hynix eMMC cards") Cc: Pratibhasagar V <pratibha@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ulf Hansson authored
commit a0741ba4 upstream. During a re-initialization of the eMMC card, we may fail to re-enable HPI. In these cases, that isn't properly reflected in the card->ext_csd.hpi_en bit, as it keeps being set. This may cause following attempts to use HPI, even if's not enabled. Let's fix this! Fixes: eb0d8f13 ("mmc: core: support HPI send command") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jens Axboe authored
commit 61cce6f6 upstream. When boxes are run near (or to) OOM, we have a problem with the discard page allocation in sd. If we fail allocating the special page, we return busy, and it'll get retried. But since ordering is honored for dispatch requests, we can keep retrying this same IO and failing. Behind that IO could be requests that want to free memory, but they never get the chance. This means you get repeated spews of traces like this: [1201401.625972] Call Trace: [1201401.631748] dump_stack+0x4d/0x65 [1201401.639445] warn_alloc+0xec/0x190 [1201401.647335] __alloc_pages_slowpath+0xe84/0xf30 [1201401.657722] ? get_page_from_freelist+0x11b/0xb10 [1201401.668475] ? __alloc_pages_slowpath+0x2e/0xf30 [1201401.679054] __alloc_pages_nodemask+0x1f9/0x210 [1201401.689424] alloc_pages_current+0x8c/0x110 [1201401.699025] sd_setup_write_same16_cmnd+0x51/0x150 [1201401.709987] sd_init_command+0x49c/0xb70 [1201401.719029] scsi_setup_cmnd+0x9c/0x160 [1201401.727877] scsi_queue_rq+0x4d9/0x610 [1201401.736535] blk_mq_dispatch_rq_list+0x19a/0x360 [1201401.747113] blk_mq_sched_dispatch_requests+0xff/0x190 [1201401.758844] __blk_mq_run_hw_queue+0x95/0xa0 [1201401.768653] blk_mq_run_work_fn+0x2c/0x30 [1201401.777886] process_one_work+0x14b/0x400 [1201401.787119] worker_thread+0x4b/0x470 [1201401.795586] kthread+0x110/0x150 [1201401.803089] ? rescuer_thread+0x320/0x320 [1201401.812322] ? kthread_park+0x90/0x90 [1201401.820787] ? do_syscall_64+0x53/0x150 [1201401.829635] ret_from_fork+0x29/0x40 Ensure that the discard page allocation has a mempool backing, so we know we can make progress. Cc: stable@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@kernel.dk> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Jörgen Storvist authored
commit 28a86092 upstream. Added USB serial option driver support for Telit LN940 series cellular modules. Covering both QMI and MBIM modes. usb-devices output (0x1900): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1900 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option usb-devices output (0x1901): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1901 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by:
Jörgen Storvist <jorgen.storvist@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Jörgen Storvist authored
commit 30360224 upstream. Added USB serial option driver support for Fibocom NL668 series cellular modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces. usb-devices output (QMI mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) usb-devices output (ECM mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by:
-
Jörgen Storvist authored
commit cc6730df upstream. Added USB serial option driver support for Simcom SIM7500/SIM7600 series cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9003 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by:
-
Tore Anderson authored
commit d57ec3c8 upstream. The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem. The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf files included with the Windows driver. Attaching the option driver to it doesn't result in a /dev/ttyUSB* device being created, so I've excluded it. Note that it is also excluded for corresponding Huawei-branded devices, cf. commit d544db29 ("USB: support new huawei devices in option.c"). T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none) I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option Signed-off-by:
Tore Anderson <tore@fud.no> Cc: stable@vger.kernel.org [ johan: drop id defines ] Signed-off-by:
-
Jörgen Storvist authored
commit 70a7444c upstream. Added USB serial option driver support for GosunCn ZTE WeLink ME3630 series cellular modules for USB modes ECM/NCM and MBIM. usb-devices output MBIM mode: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0602 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim usb-devices output ECM/NCM mode: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1476 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether Signed-off-by:
-
Nicolas Saenz Julienne authored
commit 2419f30a upstream. As commented in the struct's definition there shouldn't be anything underneath its 'priv[0]' member as it would break some macros. The patch converts the broken_suspend into a bit-field and relocates it next to to the rest of bit-fields. Fixes: a7d57abc ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC") Reported-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Mathias Nyman authored
commit 45f750c1 upstream. The code to prevent a bus suspend if a USB3 port was still in link training also reacted to USB2 port polling state. This caused bus suspend to busyloop in some cases. USB2 polling state is different from USB3, and should not prevent bus suspend. Limit the USB3 link training state check to USB3 root hub ports only. The origial commit went to stable so this need to be applied there as well Fixes: 2f31a67f ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by:
-
Hui Peng authored
commit 5146f95d upstream. The function hso_probe reads if_num from the USB device (as an u8) and uses it without a length check to index an array, resulting in an OOB memory read in hso_probe or hso_get_config_data. Add a length check for both locations and updated hso_probe to bail on error. This issue has been assigned CVE-2018-19985. Reported-by:
Hui Peng <benquike@gmail.com> Reported-by:
Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dan Carpenter authored
commit 2d204ee9 upstream The "le32_to_cpu(rsp->OutputOffset) + *plen" addition can overflow and wrap around to a smaller value which looks like it would lead to an information leak. Fixes: 4a72dafa ("SMB2 FSCTL and IOCTL worker function") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit a2015516 ] We need to synthesize events first, because some features works on top of them (on report side). Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Tested-by:
Stephane Eranian <eranian@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180314092205.23291-1-jolsa@kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit 14d15c2b upstream BUG: KASAN: use-after-free in srpt_set_enabled+0x1a9/0x1e0 [ib_srpt] Read of size 4 at addr ffff8801269d23f8 by task check/29726 CPU: 4 PID: 29726 Comm: check Not tainted 4.18.0-rc2-dbg+ #4 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014 Call Trace: dump_stack+0xa4/0xf5 print_address_description+0x6f/0x270 kasan_report+0x241/0x360 __asan_load4+0x78/0x80 srpt_set_enabled+0x1a9/0x1e0 [ib_srpt] srpt_tpg_enable_store+0xb8/0x120 [ib_srpt] configfs_write_file+0x14e/0x1d0 [configfs] __vfs_write+0xd2/0x3b0 vfs_write+0x101/0x270 ksys_write+0xab/0x120 __x64_sys_write+0x43/0x50 do_syscall_64+0x77/0x230 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f235cfe6154 Fixes: aaf45bd8 ("IB/srpt: Detect session shutdown reliably") Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Richard Weinberger authored
commit 00ee8b60 upstream We have to account the name of the symlink and not the target length. Fixes: ca7f85be ("ubifs: Add support for encrypted symlinks") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Daniel Mack authored
commit 747df197 upstream The ESD watchdog code in sta32x_watchdog() dereferences the pointer which is never assigned. This is a regression from a1be4cea ("ASoC: sta32x: Convert to direct regmap API usage.") which went unnoticed since nobody seems to use that ESD workaround. Fixes: a1be4cea ("ASoC: sta32x: Convert to direct regmap API usage.") Signed-off-by:
Daniel Mack <daniel@zonque.org> Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit b88aef36 ] If __blkdev_issue_discard is in progress and a device mapper device is reloaded with a table that doesn't support discard, q->limits.max_discard_sectors is set to zero. This results in infinite loop in __blkdev_issue_discard. This patch checks if max_discard_sectors is zero and aborts with -EOPNOTSUPP. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Tested-by:
-
Jens Axboe authored
[ Upstream commit af097f5d ] Don't build discards bigger than what the user asked for, if the user decided to limit the size by writing to 'discard_max_bytes'. Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
-
- 21 Dec, 2018 7 commits
-
-
Greg Kroah-Hartman authored
-
Nicolas Schichan authored
emit_ldx_r() and emit_a32_mov_i() were both using TMP_REG_1 and clashing with each other. Using TMP_REG_2 in emit_ldx_r() fixes the issue. Fixes: ec19e02b ("ARM: net: bpf: fix LDX instructions") Cc: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Nicolas Schichan <nschichan@freebox.fr> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Trent Piepho authored
[ Upstream commit cd7f3a24 ] In order to read correctly from asynchronously updated RTC registers, it's necessary to read repeatedly until their values do not change from read to read. It's also necessary to wait for three RTC clock ticks for certain operations. There are no timeouts in this code and these operations could possibly loop forever. To avoid kernel hangs, put in timeouts. The iMX7d can be configured to stop the SRTC on a tamper event, which will lockup the kernel inside this driver as described above. These hangs can happen when running under qemu, which doesn't emulate the SNVS RTC, though currently the driver will refuse to load on qemu due to a timeout in the driver probe method. It could also happen if the SRTC block where somehow placed into reset or the slow speed clock that drives the SRTC counter (but not the CPU) were to stop. The symptoms on a two core iMX7d are a work queue hang on rtc_timer_do_work(), which eventually blocks a systemd fsnotify operation that triggers a work queue flush, causing systemd to hang and thus causing all services that should be started by systemd, like a console getty, to fail to start or stop. Also optimize the wait code to wait less. It only needs to wait for the clock to advance three ticks, not to see it change three times. Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by:
Trent Piepho <tpiepho@impinj.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Israel Rukshin authored
[ Upstream commit d7dcdf9d ] nvmet_rdma_release_rsp() may free the response before using it at error flow. Fixes: 8407879c ("nvmet-rdma: fix possible bogus dereference under heavy load") Signed-off-by:
Israel Rukshin <israelr@mellanox.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
Max Gurtovoy <maxg@mellanox.com> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit ece27a33 ] Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode, tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us. tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode: Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit 8469636a ] Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode, tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us. tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode: Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 0544ee4b ] Some AMD based HP laptops have a SMB0001 ACPI device node which does not define any methods. This leads to the following error in dmesg: [ 5.222731] cmi: probe of SMB0001:00 failed with error -5 This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case silencing the error. In case of a failure of the i2c_add_adapter() call this commit now propagates the error from that call instead of -EIO. Signed-off-by:
-
