- 24 Oct, 2012 7 commits
-
-
Tony Lindgren authored
This allows us to eventually move omap2+ to generic debug code that's configured in Kconfig for the port. Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
This is the first set of omap cleanup patches for v3.8 merge window to remove most of the remaining plat includes to get us closer to ARM common zImage support. To avoid a huge amount of trivial merge conflicts with includes, this branch is based on several small topic branches coordinated with the driver subsystem maintainers. These branches are based on v3.7-rc1 and can also be merged into the related driver subsystem branches as needed: omap-for-v3.8/cleanup-headers-prepare few trivial driver changes omap-for-v3.8/cleanup-headers-dma move of the DMA header omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes omap-for-v3.8/cleanup-headers-mmc MMC related changes omap-for-v3.8/cleanup-headers-dss DSS related changes omap-for-v3.8/cleanup-headers-asoc ASoC related changes Note that for the dma-omap.h, it was decided that it should be is completed. For the related discussion, please see: https://patchwork.kernel.org/patch/1519591/# After these patches we still have a few plat headers remaining that will be handled in later pull requests.
-
Tony Lindgren authored
This allows us to get rid of the ifdefs in 8250.c. Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexey Brodkin authored
Modify divisor to select the nearest baud rate divider rather than the lowest. It minimizes baud rate errors especially on low UART clock frequencies. For example, if uartclk is 33000000 and baud is 115200 the ratio is about 17.9 The current code selects 17 (5% error) but should select 18 (0.5% error). This 5% error in baud rate leads to garbage on receiving end, while 0.5% doesn't. The issue showed up when using the stock 8250 driver for Synopsys DW UART. This was on a FPGA with ~12MHz UART clock. When we enabled early serial, we saw garbage which was narrowed down to the rounding error. So the bug had been latent and it only showed up with such low clock rates. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Abraham authored
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare calls as required by common clock framework. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ivo Sieben authored
When a driver has the low_latency flag set and uses the schedule_flip() function to initiate copying data to the line discipline, a workqueue is scheduled in but never actually flushed. This is incorrect use of the low_latency flag (driver should not support the low_latency flag, or use the tty_flip_buffer_push() function instead). Make sure a warning is reported to catch incorrect use of the low_latency flag. This patch goes with: cee4ad1eSigned-off-by: Ivo Sieben <meltedpianoman@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Vetter authored
Instead of BUG_ON(in_interrupt()), since that doesn't check for all the newfangled stuff like preempt. Note that this is valid since the console_sem is essentially used like a real mutex with only two twists: - we allow trylock from hardirq context - across suspend/resume we lock the logical console_lock, but drop the semaphore protecting the locking state. Now that doesn't guarantee that no one is playing tricks in single-thread atomic contexts at suspend/resume/boot time, but - I couldn't find anything suspicious with some grepping, - might_sleep shouldn't die, - and I think the upside of catching more potential issues is worth the risk of getting a might_sleep backtrace that would have been save (and then dealing with that fallout). Cc: Dave Airlie <airlied@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 22 Oct, 2012 23 commits
-
-
Jiri Slaby authored
So this is it. The big step why we did all the work over the past kernel releases. Now everything is prepared, so nothing protects us from doing that big step. | | \ \ nnnn/^l | | | | \ / / | | | '-,.__ => \/ ,-` => | '-,.__ | O __.´´) ( .` | O __.´´) ~~~ ~~ `` ~~~ ~~ The buffers are now in the tty_port structure and we can start teaching the buffer helpers (insert char/string, flip etc.) to use tty_port instead of tty_struct all around. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
For that purpose we have to temporarily introduce a second tty back pointer into tty_port. It is because serial layer, and maybe others, still do not use tty_port_tty_set/get. So that we cannot set the tty_port->tty to NULL at will now. Yes, the fix would be to convert whole serial layer and all its users to tty_port_tty_set/get. However we are in the process of removing the need of tty in most of the call sites, so this would lead to a duplicated work. Instead we have now tty_port->itty (internal tty) which will be used only in flush_to_ldisc. For that one it is ensured that itty is valid wherever the work is run. IOW, the work is synchronously cancelled before we set itty to NULL and also before hangup is processed. After we need only tty_port and not tty_struct in most code, this shall be changed to tty_port_tty_set/get and itty removed completely. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
During the move of tty buffers from tty_struct to tty_port, we will need to switch all users of buf to tty->port->buf. There are many functions where this is accessed directly in their code many times. Cache the tty->buf pointer in such functions now and change only single lines in each function in the next patch. Not that it is convenient for the next patch, but the code is now also more readable. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
They are only TTY buffers specific. And the buffers will go to tty_port in the next patches. So to remove the need to have both tty_port and tty_struct at some places, let us move the flags to tty_port. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
In some funtions we need only n_tty_data, so pass it down directly in case tty is not needed there. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
atomic_write_lock is not n_tty specific, so move it up in the tty_struct. And since these are the last ones to move, remove also the comment saying there are some ldisc' members. There are none now. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
All the ring-buffers... Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
Here we move bitmaps and use DECLARE_BITMAP to declare them in the new structure. And instead of memset, we use bitmap_zero as it is more appropriate. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
Here we start moving all the n_tty related bits from tty_struct to the newly defined n_tty_data struct in n_tty proper. In this patch primitive members and bits are moved. The rest will be done per-partes in the next patches. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
All n_tty related members from tty_struct will be moved here. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
This is a private member of n_tty. Stop accessing it. Instead, take is as an argument. This is needed to allow clean switch of the private members to a separate private structure of n_tty. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
* BUG_ON(!tty) in n_tty_set_termios -- it cannot be called with tty == NULL. It is called from two call sites. First, from n_tty_open where we have a valid tty. Second, as ld->ops->set_termios from tty_set_termios. But there we have a valid tty too. * if (!tty) in n_tty_open -- why would the TTY layer call ldisc's open with an invalid TTY? No it indeed does not. All call sites have a tty and dereference that. * BUG_ON(!tty->read_buf) in n_tty_read -- this used to be a valid check. The ldisc handling was broken some time ago when I added the check to ensure everything is OK. It still can catch the case, but no later than we move the buffer to ldisc data. Then there will be no read_buf in tty_struct, i.e. nothing to check for. * if (!tty->read_buf) in n_tty_receive_buf -- this should never happen. All callers of ldisc->ops->receive_ops should hold a reference to an ldisc and close (which frees read_buf) cannot be called until the reference is dropped. * if (WARN_ON(!tty->read_buf)) in n_tty_read -- the same as in the previous case. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
ldisc->open and close are called only once and cannot cross. So the tests in open and close are superfluous. Remove them. (But leave sets to NULL to ensure there is not a bug somewhere.) And when the tests are gone, handle properly failures in open. We leaked read_buf if allocation of echo_buf failed before. Now this is not the case anymore. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
hci_ldisc's open checks if tty_struct->disc_data is set. And if so it returns with an error. But nothing ensures disc_data to be NULL. And since ld->ops->open shall be called only once, we do not need the check at all. So remove it. Note that this is not an issue now, but n_tty will start using the disc_data pointer and this invalid 'if' would trigger then rendering TTYs over BT unusable. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: linux-bluetooth@vger.kernel.org Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
We reintroduced tty_ldisc_wait_idle in 100eeae2 (TTY: restore tty_ldisc_wait_idle) and used in set_ldisc. Then we added it also to the hangup path in 92f6fa09 (TTY: ldisc, do not close until there are readers). And we noted that there is one more path: ~ Before 65b77046 tty_ldisc_wait_idle was called also from ~ tty_ldisc_release. It is called from tty_release, so I don't think ~ we need to restore that one. Well, I was wrong. There might still be holders of an ldisc reference. Not from userspace, but drivers. If they take a reference and a user closes the device immediately after that, we have a problem. ldisc is halted and closed by TTY, but the driver still may call some ldisc's operation and cause a crash. So restore the tty_ldisc_wait_idle call also to the third location where it was before 65b77046 (tty-ldisc: turn ldisc user count into a proper refcount). Now we should be safe with respect to the ldisc reference counting as all* tty_ldisc_close paths are safely called with reference count of one. * Not the one in tty_ldisc_setup's fail path. But that is called before the first open finishes. So userspace does not see it yet. Even thought the driver is given the TTY already via ->install, it should not take a reference to the ldisc yet. If some driver is to do this, we should put one tty_ldisc_wait_idle also in the setup. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
There used to be a single tty_ldisc_ref_wait. But then, when a big-tty-mutex (BTM) was introduced, it has to be tty_ldisc_ref + tty_unlock + tty_ldisc_ref_wait + tty_lock. Later, BTM was removed from that path and tty_ldisc_ref + tty_ldisc_ref_wait remained there. But it makes no sense now. So leave there only tty_ldisc_ref_wait. And when we have a reference to an ldisc, actually use it in the loop. Otherwise it may be racy. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
Now that we have control over tty->driver_data in pty, we can just kill the /dev/pts/ in pty code too. Namely, in ->shutdown hook of tty. For pty, this is called only once, for whichever end is closed last. But we don't care, both driver_data are the inode as it used to be till now. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
Add kernel-doc texts for some devpts functions, i.e. document them. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
The goal is to stop setting and using tty->driver_data in devpts code. It should be used solely by the driver's code, pty in this case. Now driver_data are managed only in the pty driver. devpts_pty_new is switched to accept what we used to dig out of tty_struct, i.e. device node number and index. This also removes a note about driver_data being set outside of the driver. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
The goal is to stop setting and using tty->driver_data in devpts code. It should be used solely by the driver's code, pty in this case. For the cleanup of layering, we will need the inode created in devpts_pty_new to be stored into slave's driver_data. So we convert devpts_pty_new to return the inode or an ERR_PTR-encoded error in case of failure. The move of 'inode = new_inode(sb);' from declarators to the code is only cosmetical, but it makes the code easier to read. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
The goal is to stop setting and using tty->driver_data in devpts code. It should be used solely by the driver's code, pty in this case. First, here we remove TTY from devpts_get_tty and rename it to devpts_get_priv. Note we do not remove type safety, we just shift the [implicit] (void *) cast one layer up. index was unused in devpts_get_tty, so remove that from the prototype too. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ivo Sieben authored
When low_latency flag is set the TTY receive flip buffer is copied to the line discipline directly instead of using a work queue in the background. Therefor only in case a workqueue is actually used for copying data to the line discipline we'll have to flush the workqueue. This prevents unnecessary spin lock/unlock on the workqueue spin lock that can cause additional scheduling overhead on a PREEMPT_RT system. On a 200 MHz AT91SAM9261 processor setup this fixes about 100us of scheduling overhead on the TTY read call. Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Vetter authored
Dave Airlie recently discovered a locking bug in the fbcon layer, where a timer_del_sync (for the blinking cursor) deadlocks with the timer itself, since both (want to) hold the console_lock: https://lkml.org/lkml/2012/8/21/36 Unfortunately the console_lock isn't a plain mutex and hence has no lockdep support. Which resulted in a few days wasted of tracking down this bug (complicated by the fact that printk doesn't show anything when the console is locked) instead of noticing the bug much earlier with the lockdep splat. Hence I've figured I need to fix that for the next deadlock involving console_lock - and with kms/drm growing ever more complex locking that'll eventually happen. Now the console_lock has rather funky semantics, so after a quick irc discussion with Thomas Gleixner and Dave Airlie I've quickly ditched the original idead of switching to a real mutex (since it won't work) and instead opted to annotate the console_lock with lockdep information manually. There are a few special cases: - The console_lock state is protected by the console_sem, and usually grabbed/dropped at _lock/_unlock time. But the suspend/resume code drops the semaphore without dropping the console_lock (see suspend_console/resume_console). But since the same thread that did the suspend will do the resume, we don't need to fix up anything. - In the printk code there's a special trylock, only used to kick off the logbuffer printk'ing in console_unlock. But all that happens while lockdep is disable (since printk does a few other evil tricks). So no issue there, either. - The console_lock can also be acquired form irq context (but only with a trylock). lockdep already handles that. This all leaves us with annotating the normal console_lock, _unlock and _trylock functions. And yes, it works - simply unloading a drm kms driver resulted in lockdep complaining about the deadlock in fbcon_deinit: ====================================================== [ INFO: possible circular locking dependency detected ] 3.6.0-rc2+ #552 Not tainted ------------------------------------------------------- kms-reload/3577 is trying to acquire lock: ((&info->queue)){+.+...}, at: [<ffffffff81058c70>] wait_on_work+0x0/0xa7 but task is already holding lock: (console_lock){+.+.+.}, at: [<ffffffff81264686>] bind_con_driver+0x38/0x263 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (console_lock){+.+.+.}: [<ffffffff81087440>] lock_acquire+0x95/0x105 [<ffffffff81040190>] console_lock+0x59/0x5b [<ffffffff81209cb6>] fb_flashcursor+0x2e/0x12c [<ffffffff81057c3e>] process_one_work+0x1d9/0x3b4 [<ffffffff810584a2>] worker_thread+0x1a7/0x24b [<ffffffff8105ca29>] kthread+0x7f/0x87 [<ffffffff813b1204>] kernel_thread_helper+0x4/0x10 -> #0 ((&info->queue)){+.+...}: [<ffffffff81086cb3>] __lock_acquire+0x999/0xcf6 [<ffffffff81087440>] lock_acquire+0x95/0x105 [<ffffffff81058cab>] wait_on_work+0x3b/0xa7 [<ffffffff81058dd6>] __cancel_work_timer+0xbf/0x102 [<ffffffff81058e33>] cancel_work_sync+0xb/0xd [<ffffffff8120a3b3>] fbcon_deinit+0x11c/0x1dc [<ffffffff81264793>] bind_con_driver+0x145/0x263 [<ffffffff81264a45>] unbind_con_driver+0x14f/0x195 [<ffffffff8126540c>] store_bind+0x1ad/0x1c1 [<ffffffff8127cbb7>] dev_attr_store+0x13/0x1f [<ffffffff8116d884>] sysfs_write_file+0xe9/0x121 [<ffffffff811145b2>] vfs_write+0x9b/0xfd [<ffffffff811147b7>] sys_write+0x3e/0x6b [<ffffffff813b0039>] system_call_fastpath+0x16/0x1b other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(console_lock); lock((&info->queue)); lock(console_lock); lock((&info->queue)); *** DEADLOCK *** v2: Mark the lockdep_map static, noticed by Jani Nikula. Cc: Dave Airlie <airlied@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 20 Oct, 2012 9 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64Linus Torvalds authored
Pull arm64 fixes from Catalin Marinas: "Main changes: - AArch64 Linux compilation fixes following 3.7-rc1 changes (MODULES_USE_ELF_RELA, update_vsyscall() prototype) - Unnecessary register setting in start_thread() (thanks to Al Viro) - ptrace fixes" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: arm64: fix alignment padding in assembly code arm64: ptrace: use HW_BREAKPOINT_EMPTY type for disabled breakpoints arm64: ptrace: make structure padding explicit for debug registers arm64: No need to set the x0-x2 registers in start_thread() arm64: Ignore memory blocks below PHYS_OFFSET arm64: Fix the update_vsyscall() prototype arm64: Select MODULES_USE_ELF_RELA arm64: Remove duplicate inclusion of mmu_context.h in smp.c
-
Marc Zyngier authored
An interesting effect of using the generic version of linkage.h is that the padding is defined in terms of x86 NOPs, which can have even more interesting effects when the assembly code looks like this: ENTRY(func1) mov x0, xzr ENDPROC(func1) // fall through ENTRY(func2) mov x0, #1 ret ENDPROC(func2) Admittedly, the code is not very nice. But having code from another architecture doesn't look completely sane either. The fix is to add arm64's version of linkage.h, which causes the insertion of proper AArch64 NOPs. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
-
Kees Cook authored
The min/max call needed to have explicit types on some architectures (e.g. mn10300). Use clamp_t instead to avoid the warning: kernel/sys.c: In function 'override_release': kernel/sys.c:1287:10: warning: comparison of distinct pointer types lacks a cast [enabled by default] Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "Assorted small fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf python: Properly link with libtraceevent perf hists browser: Add back callchain folding symbol perf tools: Fix build on sparc. perf python: Link with libtraceevent perf python: Initialize 'page_size' variable tools lib traceevent: Fix missed freeing of subargs in free_arg() in filter lib tools traceevent: Add back pevent assignment in __pevent_parse_format() perf hists browser: Fix off-by-two bug on the first column perf tools: Remove warnings on JIT samples for srcline sort key perf tools: Fix segfault when using srcline sort key perf: Require exclude_guest to use PEBS - kernel side enforcement perf tool: Precise mode requires exclude_guest
-
Arnaldo Carvalho de Melo authored
Namhyung Kim reported that the build fails with: GEN python/perf.so gcc: error: python_ext_build/tmp//../../libtraceevent.a: No such file or directory error: command 'gcc' failed with exit status 1 cp: cannot stat `python_ext_build/lib/perf.so': No such file or directory make: *** [python/perf.so] Error 1 We need to propagate the TE_PATH variable to the setup.py file. Reported-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Link: http://lkml.kernel.org/n/tip-8umiPbm4sxpknKivbjgykhut@git.kernel.org [ Fixed superfluous variable build error. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
-
Ingo Molnar authored
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent Pull perf/urgent fixes from Arnaldo Carvalho de Melo: * The python binding needs to link with libtraceevent and to initialize the 'page_size' variable so that mmaping works again. * The callchain folding character that appears on the TUI just before the overhead had disappeared due to recent changes, add it back. * Intel PEBS in VT-x context uses the DS address as a guest linear address, even though its programmed by the host as a host linear address. This either results in guest memory corruption and or the hardware faulting and 'crashing' the virtual machine. Therefore we have to disable PEBS on VT-x enter and re-enable on VT-x exit, enforcing a strict exclude_guest. Kernel side enforcement fix by Peter Zijlstra, tooling side fix by David Ahern. * Fix build on sparc due to UAPI, fix from David Miller. * Fixes for the srclike sort key for unresolved symbols and when processing samples in JITted code, where we don't have an ELF file, just an special symbol table, fixes from Namhyung Kim. * Fix some leaks in libtraceevent, from Steven Rostedt. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM soc fixes from Olof Johansson: "A set of fixes and some minor cleanups for -rc2: - A series from Arnd that fixes warnings in drivers and other code included by ARM defconfigs. Most have been acked by corresponding maintainers (and seem quite hard to argue not picking up anyway in the few exception cases). - A few misc patches from the list for integrator/vt8500/i.MX - A batch of fixes to OMAP platforms, fixing: - boot problems on beaglebone, - regression fixes for local timers - clockdomain locking fixes - a few boot/sparse warnings - For Tegra: - Clock rate calculation overflow fix - Revert a change that removed timer clocks and a fix for symbol name clashes - For Renesas: - IO accessor / annotation cleanups to remove warnings - For Kirkwood/Dove/mvebu: - Fixes for device trees for Dove (some minor cleanups, some fixes) - Fixes for the mvebu gpio driver - Fix build problem for Feroceon due to missing ifdefs - Fix lsxl DTS files" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits) ARM: kirkwood: fix buttons on lsxl boards ARM: kirkwood: fix LEDs names for lsxl boards ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2 gpio: mvebu: Add missing breaks in mvebu_gpio_irq_set_type ARM: dove: Add crypto engine to DT ARM: dove: Remove watchdog from DT ARM: dove: Restructure SoC device tree descriptor ARM: dove: Fix clock names of sata and gbe ARM: dove: Fix tauros2 device tree init ARM: dove: Add pcie clock support ARM: OMAP2+: Allow kernel to boot even if GPMC fails to reserve memory ARM: OMAP: clockdomain: Fix locking on _clkdm_clk_hwmod_enable / disable ARM: s3c: mark s3c2440_clk_add as __init_refok spi/s3c64xx: use correct dma_transfer_direction type ARM: OMAP4: devices: fixup OMAP4 DMIC platform device error message ARM: OMAP2+: clock data: Add dev-id for the omap-gpmc dummy fck ARM: OMAP: resolve sparse warning concerning debug_card_init() ARM: OMAP4: Fix twd_local_timer_register regression ARM: tegra: add tegra_timer clock ARM: tegra: rename tegra system timer ...
-
David Howells authored
Emit the magic string that indicates a module has a signature after the signature data instead of before it. This allows module_sig_check() to be made simpler and faster by the elimination of the search for the magic string. Instead we just need to do a single memcmp(). This works because at the end of the signature data there is the fixed-length signature information block. This block then falls immediately prior to the magic number. From the contents of the information block, it is trivial to calculate the size of the signature data and thus the size of the actual module data. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 19 Oct, 2012 1 commit
-
-
git://git.infradead.org/users/jcooper/linuxOlof Johansson authored
From Jason Cooper: - improve #ifdef logic to prevent linker errors with CACHE_FEROCEON_L2 - lsxl board dts fixes * tag 'kirkwood_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux: ARM: kirkwood: fix buttons on lsxl boards ARM: kirkwood: fix LEDs names for lsxl boards ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2
-