* fixes: (27 commits)
  firmware: arm_scpi: Revert updates made during v4.15 merge window
  arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
  arm64: dts: sort vendor subdirectories in Makefile alphabetically
  MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
  arm64: dts: uniphier: remove unnecessary interrupt-parent
  arm64: dts: uniphier: correct on-board device IRQ number for PXs3
  optee: fix invalid of_node_put() in optee_driver_init()
  Revert "ARM: dts: imx53: add srtc node"
  ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
  ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
  ARM: dts: am4372: Correct the interrupts_properties of McASP
  ARM: dts: logicpd-somlv: Fix wl127x pinmux
  ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
  ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
  ARM: OMAP2+: Missing error code in omap_device_build()
  ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
  ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
  ARM: dts: NSP: Fix PPI interrupt types
  ARM: dts: NSP: Disable AHCI controller for HR NSP boards
  ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
  ...

Revert "Merge tag 'scpi-updates-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers"

Paraphrased from email from Kevin Hilman:

Revert ARM SCPI changes since v4.14.

Untested changes caused regressions in SCPI and CPUfreq/DVFS failures
on most Amlogic SoCs.  Changes reverted for v4.15 so they can be better
reviewed and tested.

These ARM SCPI changes caused SCPI regressions resulting in CPUfreq
failures on most Amlogic SoCs (found by kernelci.org.)

Unfortunately, this was not caught in linux-next due to other bugs/panics
on these platforms masking this problem so we've only found it since
we've fixed the other issues.

Since we're already in the -rc cycle, I'd prefer to revert to a known
working state (that of v4.14) rather than finding/reverting a subset,
which would just lead to another untested state.

These changes can then have some time to be better reviewed and tested
and resubmitted for v4.16.

Kevin Hilman has tested this revert on the affected Amlogic SoCs and
verified that we're back to the previous (working) condition.

This reverts commit 6710acf2, reversing
changes made to 4b367f2e.
Reported-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.15-rc cycle with two fixes for hangs with the
rest being compiler warning fixes and fixes for power states and devices
on various boards:

- Fix smatch issue introduced by recent omap device changes for legacy
  resources

- Fix SRAM virt to phys related boot hang affecting n900 and other omap3 hs
  devices found by pending CMA changes. While it seems that we have not hit
  this in other use cases, let's fix it to avoid a nasty and hard to find
  suprise as right now there is just luck keeping the SRAM virtual address
  to physical address translation working with the 0xffff high_mask.

- Fix am335x reading of domain state registers that only exist for the
  PM_CEFUSE domain and produce wrong results for other domains

- Fix missing setting for error code for omap device if allocation fails

- Fix missing modules_offs for omap3 MMC3 affecting n9/n950

- Fix cm_split_idlest() reading reserved registers showing wrong
  idlestatus

- Fixes to correct #phy-cells property for compiler warnings that
  recently started happening

- Add a missing OHCI remote-wakeup-connected property that I was supposed
  to merge after the ohci-omap3 to ohci-platform changes but somehow managed
  to drop. I only noticed this was missing while debugging the OHCI/EHCI GPS
  and modem hang

- Fix a system hang with GPS or modem connected to the OHCI/EHCI bus that
  typically happened within 20 - 40 minutes on an idle system. This turned
  out to be an issue caused by using the parent interrupt controller directly
  with the WUGEN + GIC stacked interrupt controller domains

- Fixes for logicpd-somlv GPMC for Ethernet and NAND that clearly
  have been broken since we changed GPMC to use the interrupt controller
  binding for some pins. And fix the wrong pin muxing for WLAN while at it

- Fixes for am437x interrupt and dma properties to fix compiler warnings
  that recently started happening

* tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
  ARM: dts: am4372: Correct the interrupts_properties of McASP
  ARM: dts: logicpd-somlv: Fix wl127x pinmux
  ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
  ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
  ARM: OMAP2+: Missing error code in omap_device_build()
  ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
  ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
  ARM: dts: Add remote-wakeup-connected for omap OHCI
  ARM: dts: am33xx: Add missing #phy-cells to ti,am335x-usb-phy
  ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
  ARM: OMAP2+: Fix smatch found issue for omap_device
  ARM: OMAP2/3: CM: fix cm_split_idlest functionality
  ARM: OMAP3: hwmod_data: add missing module_offs for MMC3
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

i.MX fixes for 4.15:
 - A fix for vf610-zii-dev-rev-c board which correct the unit-address
   of I2C EEPROM node to match the 'reg' property.
 - We thought the RTC block on i.MX53 is compatible with the one found
   on i.MX25, and added the device for i.MX53 device tree.  But it turns
   out that's not the case, and we have to revert the change.

* tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  Revert "ARM: dts: imx53: add srtc node"
  ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-fixes-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into fixes

UniPhier ARM SoC fixes for v4.15

- Fix IRQ number of PXs3 SoC
- Remove redundant interrupt-parent properties
- Fix arm64 DT path in MAINTAINERS

* tag 'uniphier-fixes-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
  arm64: dts: uniphier: remove unnecessary interrupt-parent
  arm64: dts: uniphier: correct on-board device IRQ number for PXs3
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tee-drv-fix-for-4.15' of https://git.linaro.org/people/jens.wiklander/linux-tee into fixes

One small fix for optee_driver_init()

* Fixes problem with an invalid call to of_node_put() in
  optee_driver_init()

* tag 'tee-drv-fix-for-4.15' of https://git.linaro.org/people/jens.wiklander/linux-tee:
  optee: fix invalid of_node_put() in optee_driver_init()
Signed-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.15,
please pull the following:

- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
  missing "#phy-cells" properties

- Florian provides two fixes for Nortsthar Plus, one that uses the correct
  interrupt specifiers for the timer/watchdog and one that disables SATA
  on BCM9582**HR boards since that leads to unidentified hangs right now

* tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux:
  ARM: dts: NSP: Fix PPI interrupt types
  ARM: dts: NSP: Disable AHCI controller for HR NSP boards
  ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Renesas ARM Based SoC DT Fixes for v4.15

Add missing '#reset-cells' property to cpg nodes.
This flagged by recent dtc.

* tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
Signed-off-by: Olof Johansson <olof@lixom.net>

"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.

Fixes the following warning in Marvell dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The list is almost sorted.  Move "lg" up to complete it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

There are several product lines in Socionext.  I maintain only
DT files prefixed with "uniphier".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>

These were added to make the ARM64 branch self-contained because
updates for ARM and ARM64 are supposed to be sent as separate
pull requests.

Now, they were merged together in Linus' tree and interrupt-parent
from the arch/arm/boot/dts/uniphier-support-card.dtsi is visible from
ARM64 DT files by the cross-arch reference.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit ba5b5034 ("arm64: dts: uniphier: route on-board device IRQ
to GPIO controller for PXs3") has incorrect update.

Fixes: ba5b5034 ("arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3")
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The first node supplied to of_find_matching_node() has its reference
counter decreased as part of call to that function. In optee_driver_init()
after calling of_find_matching_node() it's invalid to call of_node_put() on
the supplied node again.

So remove the invalid call to of_node_put().
Reported-by: Alex Shi <alex.shi@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>

This reverts commit 5b725054.

The rtc block on i.MX53 is a completely different hardware than the
one found on i.MX25.

Cc: <stable@vger.kernel.org> #4.14
Reported-by: Noel Vellemans <Noel.Vellemans@visionbms.com>
Suggested-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.

Fixes: d4cd1581 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixes the following warnings:

arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000

arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The pin assignment for the wl127x interrupt was incorrect.  I am
not sure how this every worked.  This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.

Fixes: ab8dd3ae ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working.  This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.

Fixes: 44e47164 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.

This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.

Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.

Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.

Fixes: 7136d457 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We need to set the error code if omap_device_alloc() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Referring TRM Am335X series:
http://www.ti.com/lit/ug/spruh73p/spruh73p.pdf

The LastPowerStateEntered bitfield is present only for PM_CEFUSE
domain. This is not present in any of the other power domains. Hence
remove the generic am33xx_pwrdm_read_prev_pwrst hook which wrongly
reads the reserved bit fields for all the other power domains.

Reading the reserved bits leads to wrongly interpreting the low
power transitions for various power domains that do not have the
LastPowerStateEntered field. The pm debug counters values are wrong
currently as we are incrementing them based on the reserved bits.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the CMA changes from Joonsoo Kim <iamjoonsoo.kim@lge.com>, it
was noticed that n900 stopped booting. After investigating it turned
out that n900 save_secure_ram_context does some whacky virtual to
physical address translation for the SRAM data address.

As we now only have minimal parts of omap3 idle code copied to SRAM,
running save_secure_ram_context() in SRAM is not needed. It only gets
called on PM init. And it seems there's no need to ever call this from
SRAM idle code.

So let's just keep save_secure_ram_context() in DDR, and pass it the
physical address of the parameters. We can do everything else in
omap-secure.c like we already do for other secure code.

And since we don't have any documentation, I still have no clue what
the values for 0, 1 and 1 for the parameters might be. If somebody has
figured it out, please do send a patch to add some comments.
Debugged-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This pull request brings in a fix for a warning that started occuring
when dtc from -next got merged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Booting a kernel results in the kernel warning us about the following
PPI interrupts configuration:
[    0.105127] smp: Bringing up secondary CPUs ...
[    0.110545] GIC: PPI11 is secure or misconfigured
[    0.110551] GIC: PPI13 is secure or misconfigured

Fix this by using the appropriate edge configuration for PPI11 and
PPI13, this is similar to what was fixed for Northstar (BCM5301X) in
commit 0e34079c ("ARM: dts: BCM5301X: Correct GIC_PPI interrupt
flags").

Fixes: 7b2e987d ("ARM: NSP: add minimal Northstar Plus device tree")
Fixes: 1a9d53ca ("ARM: dts: NSP: Add TWD Support to DT")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.

Fixes: 70725d6e ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c376 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported

Pull static key fix from Ingo Molnar:
 "Fix a boot warning related to bad init ordering of the static keys
  self-test"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Invoke jump_label_test() via early_initcall()

Pull objtool fixes from Ingo Molnar:
 "A handful of objtool fixes, most of them related to making the UAPI
  header-syncing warnings easier to read and easier to act upon"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Sync objtool UAPI header
  objtool: Fix cross-build
  objtool: Move kernel headers/code sync check to a script
  objtool: Move synced files to their original relative locations
  objtool: Make unreachable annotation inline asms explicitly volatile
  objtool: Add a comment for the unreachable annotation macros

Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode.  This
could occur due to corrupted stack state, which has been observed with
"ftracetest".

This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>