a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().

By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.

This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.

Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Removes below unnecessary log of almost 28 lines during boot.

musb_hdrc: hw_ep 0shared, max 64
musb_hdrc: hw_ep 1tx, max 512
musb_hdrc: hw_ep 1rx, max 512
...
...
musb_hdrc: hw_ep 13shared, max 4096
musb_hdrc: hw_ep 14shared, max 1024
musb_hdrc: hw_ep 15shared, max 1024
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

- fixed shared interrupt bug reported by Vadim Lobanov
 - fixed possible warning oops on driver unload when connected
 - prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
   when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write.  On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.

If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.

Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate().  And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...

While at it, also do the following changes :

- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
  driver does not allow stalling with non-empty Tx FIFO anyway);

- in rxstate(), stop pointlessly zeroing the 'csr' variable;

- in musb_gadget_set_halt(), move the 'done' label to a more proper
  place;

- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1304) fixes a regression in ehci-hcd.  Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.

The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake.  In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found.  In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.

Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests.  Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
  ide: fix ioctl to pass requested transfer mode to ide_find_dma_mode instead of UDMA6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sunsu: Use sunserial_console_termios() in sunsu_console_setup().
  sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
  serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
  serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
  sunsu: Fix detection of SU ports which are RSC console or control.
  sunsab: Do not set sunsab_reg.cons right before registering minors.
  sparc64: Fix definition of VMEMMAP_SIZE.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
  b44: Fix wedge when using netconsole.
  wan: cosa: drop chan->wsem on error path
  ep93xx-eth: check for zero MAC address on probe, not on device open
  NET: smc91x: Fix irq flags
  smsc9420: prevent BUG() if ethtool is called with interface down
  r8169: restore mac addr in rtl8169_remove_one and rtl_shutdown
  ipv4: additional update of dev_net(dev) to struct *net in ip_fragment.c, NULL ptr OOPS
  e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failure
  sctp: on T3_RTX retransmit all the in-flight chunks
  pktgen: Fix netdevice unregister
  macvlan: fix gso_max_size setting
  rfkill: fix miscdev ops
  ath9k: set ps_default as false
  hso: fix soft-lockup
  hso: fix debug routines
  pktgen: Fix device name compares
  stmmac: do not fail when the timer cannot be used.
  stmmac: fixed a compilation error when use the external timer
  netfilter: xt_limit: fix invalid return code in limit_mt_check()
  Au1x00: fix crash when trying register_netdev()
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: reject O_DIRECT flag also in fuse_create

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: keyboard - fix braille keyboard keysym generation

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: fix irq enable/disable in runtime PM code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: pass correct iso xmit timestamps to core
  firewire: ohci: Make cycleMatch ISO transmission work

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (13372): staging/go7007: fix mutex function usage for s2250
  staging/go7007: Fix compilation by re-adding the missing s2250-loader.h
  V4L/DVB (13530): Fix wrong parameter order in memset
  V4L/DVB (13481): sh_mobile_ceu_camera: fix compile warning
  V4L/DVB (13436): cxusb: Fix hang on DViCO FusionHDTV DVB-T Dual Digital 4 (rev 1)
  V4L/DVB (13412): SMS_SIANO_MDTV should depend on HAS_DMA
  V4L/DVB (13372a): MAINTAINERS: addition of gspca_gl860 driver
  V4L/DVB (13371): davinci: remove stray duplicate config pointer
  V4L/DVB (13366): em28xx: fix Reddo DVB-C USB TV Box GPIO
  V4L/DVB (13345): soc-camera: sh_mobile_ceu_camera: call pm_runtime_disable
  V4L/DVB (13344): soc-camera: properly initialise the device object when reusing
  V4L/DVB (13343): v4l: add more missing linux/sched.h includes
  V4L/DVB (13321): radio-gemtek-pci: fix double mutex_lock

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Select CONFIG_SHMEM
  drm/i915: Fix CRT hotplug detect by checking really no channels attached
  agp/intel: new host bridge support
  drm/i915: Add more registers save/restore for Ironlake suspend
  drm/i915: Fix IRQ stall issue on Ironlake
  drm/i915: HDMI hardware workaround for Ironlake
  drm/i915: Fix and cleanup DPLL calculation for Ironlake
  drm/i915: Avoid potential sleep whilst holding spinlock

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cciss: make device attrs static
  Thaw refrigerated bdi flusher threads before invoking kthread_stop on them

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  acerhdf: return temperature in milidegree instead of degree
  thinkpad-acpi: fix detection of old ThinkPads
  thinkpad-acpi: fix sign of ERESTARTSYS return
  ACPI: Add Thinkpad T400, T500 to OSI(Linux) white-list
  ACPICA: Silence the warning about _BIF returning the buffer
  ACPI: DMI init_set_sci_en_on_resume for HP-Compaq C700

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Enable ACPI PDC handshake for VIA/Centaur CPUs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: AACI: fix recording bug
  ALSA: AACI: fix AC97 multiple-open bug
  ASoC: AIC23: Fixing infinite loop in resume path
  ASoC: Fix suspend with active audio streams

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/fb: fix FBIOGET/PUT_VSCREENINFO pixel clock handling
  drm: make sure page protections are updated after changing vm_flags
  drm/radeon/kms: Report vga connector is connected according to ddc_probe
  drm: mm always protect change to unused_nodes with unused_lock spinlock
  drm/radeon/kms: Disable TV load detect on RS400,RC410,RS480
  drm/radeon/kms: read back register before writing in IIO.
  drm/radeon/kms: fix handling of d1/d2 vga
  drm: work around EDIDs with bad htotal/vtotal values
  drm/radeon/kms: resume AGP by calling init.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  shdma: fix initialization error handling
  ioat3: fix pq completion versus channel deallocation race
  async_tx: build-time toggling of async_{syndrome,xor}_val dma support
  dmaengine: include xor/pq validate in device_has_all_tx_types()
  ioat2,3: report all uncorrectable errors
  ioat3: specify valid address for disabled-Q or disabled-P
  ioat2,3: disable asynchronous error notifications
  ioat3: dca and raid operations are incompatible
  ioat: silence "dca disabled" messages

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  Staging: octeon-ethernet: Assign proper MAC addresses.
  Staging: Octeon: Use symbolic values for irq numbers.
  MIPS: Octeon: Fix compile error in drivers/staging/octeon/ethernet-mdio.c

In 2.6.23 kernel, commit a32ea1e1
("Fix read/truncate race") fixed a race in the generic code, and as a
side effect, now do_generic_file_read() can ask us to readpage() past
the i_size. This seems to be correctly handled by the block routines
(e.g. block_read_full_page() fills the page with zeroes in case if
somebody is trying to read past the last inode's block).

JFFS2 doesn't handle this; it assumes that it won't be asked to read
pages which don't exist -- and thus that there will be at least _one_
valid 'frag' on the page it's being asked to read. It will fill any
holes with the following memset:

  memset(buf, 0, min(end, frag->ofs + frag->size) - offset);

When the 'closest smaller match' returned by jffs2_lookup_node_frag() is
actually on a previous page and ends before 'offset', that results in:

  memset(buf, 0, <huge unsigned negative>);

Hopefully, in most cases the corruption is fatal, and quickly causing
random oopses, like this:

  root@10.0.0.4:~/ltp-fs-20090531# ./testcases/kernel/fs/ftest/ftest01
  Unable to handle kernel paging request for data at address 0x00000008
  Faulting instruction address: 0xc01cd980
  Oops: Kernel access of bad area, sig: 11 [#1]
  [...]
  NIP [c01cd980] rb_insert_color+0x38/0x184
  LR [c0043978] enqueue_hrtimer+0x88/0xc4
  Call Trace:
  [c6c63b60] [c004f9a8] tick_sched_timer+0xa0/0xe4 (unreliable)
  [c6c63b80] [c0043978] enqueue_hrtimer+0x88/0xc4
  [c6c63b90] [c0043a48] __run_hrtimer+0x94/0xbc
  [c6c63bb0] [c0044628] hrtimer_interrupt+0x140/0x2b8
  [c6c63c10] [c000f8e8] timer_interrupt+0x13c/0x254
  [c6c63c30] [c001352c] ret_from_except+0x0/0x14
  --- Exception: 901 at memset+0x38/0x5c
      LR = jffs2_read_inode_range+0x144/0x17c
  [c6c63cf0] [00000000] (null) (unreliable)

This patch fixes the issue, plus fixes all LTP tests on NAND/UBI with
JFFS2 filesystem that were failing since 2.6.23 (seems like the bug
above also broke the truncation).
Reported-By: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-By: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The fbdev mailing lists at SourceForge have been migrated to a single
mailing list at kernel.org: linux-fbdev@vger.kernel.org.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-kconfig:
  kconfig: Fix make O=<dir> local{mod,yes}config

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_fsl: Split hard and soft reset

* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-fscache: (31 commits)
  FS-Cache: Provide nop fscache_stat_d() if CONFIG_FSCACHE_STATS=n
  SLOW_WORK: Fix GFS2 to #include <linux/module.h> before using THIS_MODULE
  SLOW_WORK: Fix CIFS to pass THIS_MODULE to slow_work_register_user()
  CacheFiles: Don't log lookup/create failing with ENOBUFS
  CacheFiles: Catch an overly long wait for an old active object
  CacheFiles: Better showing of debugging information in active object problems
  CacheFiles: Mark parent directory locks as I_MUTEX_PARENT to keep lockdep happy
  CacheFiles: Handle truncate unlocking the page we're reading
  CacheFiles: Don't write a full page if there's only a partial page to cache
  FS-Cache: Actually requeue an object when requested
  FS-Cache: Start processing an object's operations on that object's death
  FS-Cache: Make sure FSCACHE_COOKIE_LOOKING_UP cleared on lookup failure
  FS-Cache: Add a retirement stat counter
  FS-Cache: Handle pages pending storage that get evicted under OOM conditions
  FS-Cache: Handle read request vs lookup, creation or other cache failure
  FS-Cache: Don't delete pending pages from the page-store tracking tree
  FS-Cache: Fix lock misorder in fscache_write_op()
  FS-Cache: The object-available state can't rely on the cookie to be available
  FS-Cache: Permit cache retrieval ops to be interrupted in the initial wait phase
  FS-Cache: Use radix tree preload correctly in tracking of pages to be stored
  ...

Fix mutex function usage, which was overlooked in a previous patch.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

As pointed by Stefan Lippers-Hollmann <s.L-H@gmx.de>,

Commit:	fd9a40da broke s2250
compilation.

This patch re-adds the missing s2250-loader.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

We can have bzip2 compressed images nowadays.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel unwinding is broken with gcc >= 4.x.  Part of the problem is that
binutils seems very sensitive to where the unwind information is stored.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pcm->r[1].slots is the double rate slot information, not the
capture information.  For capture, 'pcm' will already be the
capture ac97 pcm structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixes kernel bugzilla #14691

Due to the way netpoll works, it is perfectly legal to see
NAPI already scheduled when new device events are pending
in b44_interrupt().

So logging a message about it is wrong and in fact harmful.

Based upon a patch by Andreas Mohr.
Signed-off-by: David S. Miller <davem@davemloft.net>

The other paths all drop chan->wsem.  This was found by a static
checker (smatch).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we happen to have registered the driver without passing
a MAC address, we will print a zero MAC address and register
the interface with this invalid address, this is confusin. This
patch moves the checking of a valid ethernet address and the
generation of a random one down from the open function to
the probe function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>