- 03 Mar, 2016 40 commits
-
-
David Sterba authored
commit ca8a51b3 upstream. There is one ENOSPC case that's very confusing. There's Available greater than zero but no file operation succeds (besides removing files). This happens when the metadata are exhausted and there's no possibility to allocate another chunk. In this scenario it's normal that there's still some space in the data chunk and the calculation in df reflects that in the Avail value. To at least give some clue about the ENOSPC situation, let statfs report zero value in Avail, even if there's still data space available. Current: /dev/sdb1 4.0G 3.3G 719M 83% /mnt/test New: /dev/sdb1 4.0G 3.3G 0 100% /mnt/test We calculate the remaining metadata space minus global reserve. If this is (supposedly) smaller than zero, there's no space. But this does not hold in practice, the exhausted state happens where's still some positive delta. So we apply some guesswork and compare the delta to a 4M threshold. (Practically observed delta was 2M.) We probably cannot calculate the exact threshold value because this depends on the internal reservations requested by various operations, so some operations that consume a few metadata will succeed even if the Avail is zero. But this is better than the other way around. Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Josef Bacik authored
commit be7bd730 upstream. We hit this panic on a few of our boxes this week where we have an ordered_extent with an NULL inode. We do an igrab() of the inode in writepages, but weren't doing it in writepage which can be called directly from the VM on dirty pages. If the inode has been unlinked then we could have I_FREEING set which means igrab() would return NULL and we get this panic. Fix this by trying to igrab in btrfs_writepage, and if it returns NULL then just redirty the page and return AOP_WRITEPAGE_ACTIVATE; so the VM knows it wasn't successful. Thanks, Signed-off-by:
Josef Bacik <jbacik@fb.com> Reviewed-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
-
Anand Jain authored
commit b2acdddf upstream. Looks like oversight, call brelse() when checksum fails. Further down the code, in the non error path, we do call brelse() and so we don't see brelse() in the goto error paths. Signed-off-by:
Anand Jain <anand.jain@oracle.com> Reviewed-by:
-
David Hildenbrand authored
commit 9abc2a08 upstream. The kernel now always uses vector registers when available, however KVM has special logic if support is really enabled for a guest. If support is disabled, guest_fpregs.fregs will only contain memory for the fpu. The kernel, however, will store vector registers into that area, resulting in crazy memory overwrites. Simply extending that area is not enough, because the format of the registers also changes. We would have to do additional conversions, making the code even more complex. Therefore let's directly use one place for the vector/fpu registers + fpc (in kvm_run). We just have to convert the data properly when accessing it. This makes current code much easier. Please note that vector/fpu registers are now always stored to vcpu->run->s.regs.vrs. Although this data is visible to QEMU and used for migration, we only guarantee valid values to user space when KVM_SYNC_VRS is set. As that is only the case when we have vector register support, we are on the safe side. Fixes: b5510d9b ("s390/fpu: always enable the vector facility if it is available") Cc: stable@vger.kernel.org # v4.4 d9a3a09a s390/kvm: remove dependency on struct save_area definition Signed-off-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> [adopt to d9a3a09a] Signed-off-by:
-
Martin Schwidefsky authored
commit d9a3a09a upstream. Replace the offsets based on the struct area_area with the offset constants from asm-offsets.c based on the struct _lowcore. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Roman Volkov authored
commit f9eccf24 upstream. The vt8500 clocksource driver declares itself as capable to handle the minimum delay of 4 cycles by passing the value into clockevents_config_and_register(). The vt8500_timer_set_next_event() requires the passed cycles value to be at least 16. The impact is that userspace hangs in nanosleep() calls with small delay intervals. This problem is reproducible in Linux 4.2 starting from: c6eb3f70 ('hrtimer: Get rid of hrtimer softirq') From Russell King, more detailed explanation: "It's a speciality of the StrongARM/PXA hardware. It takes a certain number of OSCR cycles for the value written to hit the compare registers. So, if a very small delta is written (eg, the compare register is written with a value of OSCR + 1), the OSCR will have incremented past this value before it hits the underlying hardware. The result is, that you end up waiting a very long time for the OSCR to wrap before the event fires. So, we introduce a check in set_next_event() to detect this and return -ETIME if the calculated delta is too small, which causes the generic clockevents code to retry after adding the min_delta specified in clockevents_config_and_register() to the current time value. min_delta must be sufficient that we don't re-trip the -ETIME check - if we do, we will return -ETIME, forward the next event time, try to set it, return -ETIME again, and basically lock the system up. So, min_delta must be larger than the check inside set_next_event(). A factor of two was chosen to ensure that this situation would never occur. The PXA code worked on PXA systems for years, and I'd suggest no one changes this mechanism without access to a wide range of PXA systems, otherwise they're risking breakage." Cc: Russell King <linux@arm.linux.org.uk> Acked-by:
Alexey Charkov <alchark@gmail.com> Signed-off-by:
Roman Volkov <rvolkov@v1ros.org> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Thomas Gleixner authored
commit 570540d5 upstream. commit 71f64340 changed the handling of irq_desc->action from CPU 0 CPU 1 free_irq() lock(desc) lock(desc) handle_edge_irq() if (desc->action) { handle_irq_event() action = desc->action unlock(desc) desc->action = NULL handle_irq_event_percpu(desc, action) action->xxx to CPU 0 CPU 1 free_irq() lock(desc) lock(desc) handle_edge_irq() if (desc->action) { handle_irq_event() unlock(desc) desc->action = NULL handle_irq_event_percpu(desc, action) action = desc->action action->xxx So if free_irq manages to set the action to NULL between the unlock and before the readout, we happily dereference a null pointer. We could simply revert 71f64340, but we want to preserve the better code generation. A simple solution is to change the action loop from a do {} while to a while {} loop. This is safe because we either see a valid desc->action or NULL. If the action is about to be removed it is still valid as free_irq() is blocked on synchronize_irq(). CPU 0 CPU 1 free_irq() lock(desc) lock(desc) handle_edge_irq() handle_irq_event(desc) set(INPROGRESS) unlock(desc) handle_irq_event_percpu(desc) action = desc->action desc->action = NULL while (action) { action->xxx ... action = action->next; sychronize_irq() while(INPROGRESS); lock(desc) clr(INPROGRESS) free(action) That's basically the same mechanism as we have for shared interrupts. action->next can become NULL while handle_irq_event_percpu() runs. Either it sees the action or NULL. It does not matter, because action itself cannot go away before the interrupt in progress flag has been cleared. Fixes: commit 71f64340 "genirq: Remove the second parameter from handle_irq_event_percpu()" Reported-by: zyjzyj2000@gmail.com Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Huang Shijie <shijie.huang@arm.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1601131224190.3575@nanosSigned-off-by:
-
Mel Gorman authored
commit 8479eba7 upstream. Commit 4167e9b2 ("mm: remove GFP_THISNODE") removed the GFP_THISNODE flag combination due to confusing semantics. It noted that alloc_misplaced_dst_page() was one such user after changes made by commit e97ca8e5 ("mm: fix GFP_THISNODE callers and clarify"). Unfortunately when GFP_THISNODE was removed, users of alloc_misplaced_dst_page() started waking kswapd and entering direct reclaim because the wrong GFP flags are cleared. The consequence is that workloads that used to fit into memory now get reclaimed which is addressed by this patch. The problem can be demonstrated with "mutilate" that exercises memcached which is software dedicated to memory object caching. The configuration uses 80% of memory and is run 3 times for varying numbers of clients. The results on a 4-socket NUMA box are mutilate 4.4.0 4.4.0 vanilla numaswap-v1 Hmean 1 8394.71 ( 0.00%) 8395.32 ( 0.01%) Hmean 4 30024.62 ( 0.00%) 34513.54 ( 14.95%) Hmean 7 32821.08 ( 0.00%) 70542.96 (114.93%) Hmean 12 55229.67 ( 0.00%) 93866.34 ( 69.96%) Hmean 21 39438.96 ( 0.00%) 85749.21 (117.42%) Hmean 30 37796.10 ( 0.00%) 50231.49 ( 32.90%) Hmean 47 18070.91 ( 0.00%) 38530.13 (113.22%) The metric is queries/second with the more the better. The results are way outside of the noise and the reason for the improvement is obvious from some of the vmstats 4.4.0 4.4.0 vanillanumaswap-v1r1 Minor Faults 1929399272 2146148218 Major Faults 19746529 3567 Swap Ins 57307366 9913 Swap Outs 50623229 17094 Allocation stalls 35909 443 DMA allocs 0 0 DMA32 allocs 72976349 170567396 Normal allocs 5306640898 5310651252 Movable allocs 0 0 Direct pages scanned 404130893 799577 Kswapd pages scanned 160230174 0 Kswapd pages reclaimed 55928786 0 Direct pages reclaimed 1843936 41921 Page writes file 2391 0 Page writes anon 50623229 17094 The vanilla kernel is swapping like crazy with large amounts of direct reclaim and kswapd activity. The figures are aggregate but it's known that the bad activity is throughout the entire test. Note that simple streaming anon/file memory consumers also see this problem but it's not as obvious. In those cases, kswapd is awake when it should not be. As there are at least two reclaim-related bugs out there, it's worth spelling out the user-visible impact. This patch only addresses bugs related to excessive reclaim on NUMA hardware when the working set is larger than a NUMA node. There is a bug related to high kswapd CPU usage but the reports are against laptops and other UMA hardware and is not addressed by this patch. Signed-off-by:
Mel Gorman <mgorman@techsingularity.net> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Andrea Arcangeli authored
commit ad33bb04 upstream. pmd_trans_unstable()/pmd_none_or_trans_huge_or_clear_bad() were introduced to locklessy (but atomically) detect when a pmd is a regular (stable) pmd or when the pmd is unstable and can infinitely transition from pmd_none() and pmd_trans_huge() from under us, while only holding the mmap_sem for reading (for writing not). While holding the mmap_sem only for reading, MADV_DONTNEED can run from under us and so before we can assume the pmd to be a regular stable pmd we need to compare it against pmd_none() and pmd_trans_huge() in an atomic way, with pmd_trans_unstable(). The old pmd_trans_huge() left a tiny window for a race. Useful applications are unlikely to notice the difference as doing MADV_DONTNEED concurrently with a page fault would lead to undefined behavior. [akpm@linux-foundation.org: tidy up comment grammar/layout] Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Reported-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
-
Guozhonghua authored
commit a4a8481f upstream. When doing append direct io cleanup, if deleting inode fails, it goes out without unlocking inode, which will cause the inode deadlock. This issue was introduced by commit cf1776a9 ("ocfs2: fix a tiny race when truncate dio orohaned entry"). Signed-off-by:
Guozhonghua <guozhonghua@h3c.com> Signed-off-by:
Joseph Qi <joseph.qi@huawei.com> Reviewed-by:
Gang He <ghe@suse.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
-
Daniel Vetter authored
commit 97e5ed11 upstream. We get tons of cases where the master interrupt handler apparently set a bit, with the SDEIIR disagreeing. No idea what's going on there, but it's consistent on gen8+, no one seems to care about it and it's making CI results flaky. Shut it up. No idea what's going on here, but we've had fun with PCH interrupts before: commit 44498aea Author: Paulo Zanoni <paulo.r.zanoni@intel.com> Date: Fri Feb 22 17:05:28 2013 -0300 drm/i915: also disable south interrupts when handling them Note that there's a regression report in Bugzilla, and other regression reports on the mailing lists keep croping up. But no ill effects have ever been reported. But for paranoia still keep the message at a debug level as a breadcrumb, just in case. This message was introduced in commit 38cc46d7 Author: Oscar Mateo <oscar.mateo@intel.com> Date: Mon Jun 16 16:10:59 2014 +0100 drm/i915/bdw: Ack interrupts before handling them (GEN8) v2: Improve commit message a bit. Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1445590572-23631-2-git-send-email-daniel.vetter@ffwll.ch Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92084 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80896Acked-by:
Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Hariprasad S authored
commit 67f1aee6 upstream. The cxgb3_*_send() functions return NET_XMIT_ values, which are positive integers values. So don't treat positive return values as an error. Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> [a pox on developers and maintainers who do not cc: stable for bug fixes like this - gregkh] Signed-off-by:
-
Michael Welling authored
commit 2f538c01 upstream. Occasionally the setup function will be called multiple times. Only request the gpio the first time otherwise -EBUSY will occur on subsequent calls to setup. Reported-by:
Joseph Bell <joe@iachieved.it> Signed-off-by:
Michael Welling <mwelling@ieee.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Lisa Du authored
commit 7a64cd88 upstream. There's one point was missed in the patch commit da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes."). When configure BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of void * is 64bit on 64bit system. Correct it here. Signed-off-by:
Lisa Du <cldu@marvell.com> Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Fixes: da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes.") Acked-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Bjørn Mork authored
commit d061c1ca upstream. Thomas reports: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05c6 ProdID=6001 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Andrey Skvortsov authored
commit 3158a8d4 upstream. $ lsusb: Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option $ usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 2 P: Vendor=1e0e ProdID=9001 Rev= 2.32 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) The last interface (6) is used for Android Composite ADB interface. Serial port layout: 0: QCDM/DIAG 1: NMEA 2: AT 3: AT/PPP 4: audio Signed-off-by:
Andrey Skvortsov <andrej.skvortzov@gmail.com> Signed-off-by:
-
Ken Lin authored
commit 6627ae19 upstream. Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards. Signed-off-by:
Ken Lin <ken.lin@advantech.com.tw> Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by:
-
John Youn authored
commit c4509601 upstream. The assignement of EP transfer resources was not handled properly in the dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") previously fixed one aspect of this where resources may be exhausted with multiple calls to SET_INTERFACE. However, it introduced an issue where composite devices with multiple interfaces can be assigned the same transfer resources for different endpoints. This patch solves both issues. The assignment of transfer resources cannot perfectly follow the data book due to the fact that the controller driver does not have all knowledge of the configuration in advance. It is given this information piecemeal by the composite gadget framework after every SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook programming model in this scenario can cause errors. For two reasons: 1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple interfaces. 2) The databook does not mention doing more DEPXFERCFG for new endpoint on alt setting (8.1.6). The following simplified method is used instead: All hardware endpoints can be assigned a transfer resource and this setting will stay persistent until either a core reset or hibernation. So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for every hardware endpoint as well. We are guaranteed that there are as many transfer resources as endpoints. This patch triggers off of the calling dwc3_gadget_start_config() for EP0-out, which always happens first, and which should only happen in one of the above conditions. Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Reported-by:
Ravi Babu <ravibabu@ti.com> Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
-
Gerhard Uttenthaler authored
commit 90cfde46 upstream. This patch fixes the problem that more CAN messages could be sent to the interface as could be send on the CAN bus. This was more likely for slow baud rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under heavy TX load this produced another bulk transfer without checking the free_slots variable and hence caused the overflow in the interface. Signed-off-by:
Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Nikolay Borisov authored
commit 18d03e8c upstream. When a thin pool is being destroyed delayed work items are cancelled using cancel_delayed_work(), which doesn't guarantee that on return the delayed item isn't running. This can cause the work item to requeue itself on an already destroyed workqueue. Fix this by using cancel_delayed_work_sync() which guarantees that on return the work item is not running anymore. Fixes: 905e51b3 ("dm thin: commit outstanding data every second") Fixes: 85ad643b ("dm thin: add timeout to stop out-of-data-space mode holding IO forever") Signed-off-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Kent Overstreet authored
commit 627ccd20 upstream. Previously, it would only scan the entire disk if it was starting from the very start of the disk - i.e. if the previous scan got to the end. This was broken by refill_full_stripes(), which updates last_scanned so that refill_dirty was never triggering the searched_from_start path. But if we change refill_dirty() to always scan the entire disk if necessary, regardless of what last_scanned was, the code gets cleaner and we fix that bug too. Signed-off-by:
Kent Overstreet <kent.overstreet@gmail.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Stefan Bader authored
commit 8d16ce54 upstream. Added a safeguard in the shutdown case. At least while not being attached it is also possible to trigger a kernel bug by writing into writeback_running. This change adds the same check before trying to wake up the thread for that case. Signed-off-by:
Stefan Bader <stefan.bader@canonical.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Signed-off-by:
-
Gabriel de Perthuis authored
commit d7076f21 upstream. Allows to use register, not register_quiet in udev to avoid "device_busy" error. The initial patch proposed at https://lkml.org/lkml/2013/8/26/549 by Gabriel de Perthuis <g2p.code@gmail.com> does not unlock the mutex and hangs the kernel. See http://thread.gmane.org/gmane.linux.kernel.bcache.devel/2594 for the discussion. Cc: Denis Bychkov <manover@gmail.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Gabriel de Perthuis <g2p.code@gmail.com> Signed-off-by:
-
Zheng Liu authored
commit 2ecf0cdb upstream. In bcache_init() function it forgot to unregister reboot notifier if bcache fails to unregister a block device. This commit fixes this. Signed-off-by:
Zheng Liu <wenqing.lz@taobao.com> Tested-by:
Joshua Schmid <jschmid@suse.com> Tested-by:
Eric Wheeler <bcache@linux.ewheeler.net> Cc: Kent Overstreet <kmo@daterainc.com> Signed-off-by:
-
Al Viro authored
commit 4d4d8573 upstream. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Tested-by:
-
Zheng Liu authored
commit fecaee6f upstream. This bug can be reproduced by the following script: #!/bin/bash bcache_sysfs="/sys/fs/bcache" function clear_cache() { if [ ! -e $bcache_sysfs ]; then echo "no bcache sysfs" exit fi cset_uuid=$(ls -l $bcache_sysfs|head -n 2|tail -n 1|awk '{print $9}') sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/detach" sleep 5 sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/attach" } for ((i=0;i<10;i++)); do clear_cache done The warning messages look like below: [ 275.948611] ------------[ cut here ]------------ [ 275.963840] WARNING: at fs/sysfs/dir.c:512 sysfs_add_one+0xb8/0xd0() (Tainted: P W --------------- ) [ 275.979253] Hardware name: Tecal RH2285 [ 275.994106] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:09.0/0000:08:00.0/host4/target4:2:1/4:2:1:0/block/sdb/sdb1/bcache/cache' [ 276.024105] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan] [ 276.072643] Pid: 2765, comm: sh Tainted: P W --------------- 2.6.32 #1 [ 276.089315] Call Trace: [ 276.105801] [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0 [ 276.122650] [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50 [ 276.139361] [<ffffffff81205c08>] ? sysfs_add_one+0xb8/0xd0 [ 276.156012] [<ffffffff8120609b>] ? sysfs_do_create_link+0x12b/0x170 [ 276.172682] [<ffffffff81206113>] ? sysfs_create_link+0x13/0x20 [ 276.189282] [<ffffffffa03bda21>] ? bcache_device_link+0xc1/0x110 [bcache] [ 276.205993] [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache] [ 276.222794] [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache] [ 276.239680] [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110 [ 276.256594] [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170 [ 276.273364] [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0 [ 276.290133] [<ffffffff811890b1>] ? sys_write+0x51/0x90 [ 276.306368] [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b [ 276.322301] ---[ end trace 9f5d4fcdd0c3edfb ]--- [ 276.338241] ------------[ cut here ]------------ [ 276.354109] WARNING: at /home/wenqing.lz/bcache/bcache/super.c:720 bcache_device_link+0xdf/0x110 [bcache]() (Tainted: P W --------------- ) [ 276.386017] Hardware name: Tecal RH2285 [ 276.401430] Couldn't create device <-> cache set symlinks [ 276.401759] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan] [ 276.465477] Pid: 2765, comm: sh Tainted: P W --------------- 2.6.32 #1 [ 276.482169] Call Trace: [ 276.498610] [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0 [ 276.515405] [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50 [ 276.532059] [<ffffffffa03bda3f>] ? bcache_device_link+0xdf/0x110 [bcache] [ 276.548808] [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache] [ 276.565569] [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache] [ 276.582418] [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110 [ 276.599341] [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170 [ 276.616142] [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0 [ 276.632607] [<ffffffff811890b1>] ? sys_write+0x51/0x90 [ 276.648671] [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b [ 276.664756] ---[ end trace 9f5d4fcdd0c3edfc ]--- We forget to clear BCACHE_DEV_UNLINK_DONE flag in bcache_device_attach() function when we attach a backing device first time. After detaching this backing device, this flag will be true and sysfs_remove_link() isn't called in bcache_device_unlink(). Then when we attach this backing device again, sysfs_create_link() will return EEXIST error in bcache_device_link(). So the fix is trival and we clear this flag in bcache_device_link(). Signed-off-by:
-
Kent Overstreet authored
commit c5f1e5ad upstream. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Tested-by:
-
Zheng Liu authored
commit 2ef9ccbf upstream. Subject : [PATCH v2] bcache: fix a livelock in btree lock Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM) This commit tries to fix a livelock in bcache. This livelock might happen when we causes a huge number of cache misses simultaneously. When we get a cache miss, bcache will execute the following path. ->cached_dev_make_request() ->cached_dev_read() ->cached_lookup() ->bch->btree_map_keys() ->btree_root() <------------------------ ->bch_btree_map_keys_recurse() | ->cache_lookup_fn() | ->cached_dev_cache_miss() | ->bch_btree_insert_check_key() -| [If btree->seq is not equal to seq + 1, we should return EINTR and traverse btree again.] In bch_btree_insert_check_key() function we first need to check upgrade flag (op->lock == -1), and when this flag is true we need to release read btree->lock and try to take write btree->lock. During taking and releasing this write lock, btree->seq will be monotone increased in order to prevent other threads modify this in cache miss (see btree.h:74). But if there are some cache misses caused by some requested, we could meet a livelock because btree->seq is always changed by others. Thus no one can make progress. This commit will try to take write btree->lock if it encounters a race when we traverse btree. Although it sacrifice the scalability but we can ensure that only one can modify the btree. Signed-off-by:
-
Jason Andryuk authored
commit a6807590 upstream. The comparisons should be >= since 0x800 and 0x80 require an additional bit to store. For the 3 byte case, the existing shift would drop off 2 more bits than intended. For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in byte 2. Signed-off-by:
Jason Andryuk <jandryuk@gmail.com> Reviewed-by:
Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Matt Fleming authored
commit e246eb56 upstream. Laszlo explains why this is a good idea, 'This is because the pstore filesystem can be backed by UEFI variables, and (for example) a crash might dump the last kilobytes of the dmesg into a number of pstore entries, each entry backed by a separate UEFI variable in the above GUID namespace, and with a variable name according to the above pattern. Please see "drivers/firmware/efi/efi-pstore.c". While this patch series will not prevent the user from deleting those UEFI variables via the pstore filesystem (i.e., deleting a pstore fs entry will continue to delete the backing UEFI variable), I think it would be nice to preserve the possibility for the sysadmin to delete Linux-created UEFI variables that carry portions of the crash log, *without* having to mount the pstore filesystem.' There's also no chance of causing machines to become bricked by deleting these variables, which is the whole purpose of excluding things from the whitelist. Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so that we don't have to update the string in the future if new variable name formats are created for crash dump variables. Reported-by:
Peter Jones <pjones@redhat.com> Tested-by:
-
Peter Jones authored
commit ed8b0de5 upstream. "rm -rf" is bricking some peoples' laptops because of variables being used to store non-reinitializable firmware driver data that's required to POST the hardware. These are 100% bugs, and they need to be fixed, but in the mean time it shouldn't be easy to *accidentally* brick machines. We have to have delete working, and picking which variables do and don't work for deletion is quite intractable, so instead make everything immutable by default (except for a whitelist), and make tools that aren't quite so broad-spectrum unset the immutable flag. Signed-off-by:
Lee, Chun-Yi <jlee@suse.com> Acked-by:
Matthew Garrett <mjg59@coreos.com> Signed-off-by:
-
Peter Jones authored
commit 8282f5d9 upstream. All the variables in this list so far are defined to be in the global namespace in the UEFI spec, so this just further ensures we're validating the variables we think we are. Including the guid for entries will become more important in future patches when we decide whether or not to allow deletion of variables based on presence in this list. Signed-off-by:
-
Peter Jones authored
commit 3dcb1f55 upstream. Actually translate from ucs2 to utf8 before doing the test, and then test against our other utf8 data, instead of fudging it. Signed-off-by:
-
Peter Jones authored
commit e0d64e6a upstream. Translate EFI's UCS-2 variable names to UTF-8 instead of just assuming all variable names fit in ASCII. Signed-off-by:
-
Peter Jones authored
commit 73500267 upstream. This adds ucs2_utf8size(), which tells us how big our ucs2 string is in bytes, and ucs2_as_utf8, which translates from ucs2 to utf8.. Signed-off-by:
-
Arnd Bergmann authored
commit be95485a upstream. The PSCI SMP implementation is built only when both CONFIG_SMP and CONFIG_ARM_PSCI are set, so a configuration that has the latter but not the former can get a link error when it tries to call psci_smp_available(). arch/arm/mach-tegra/built-in.o: In function `tegra114_cpuidle_init': cpuidle-tegra114.c:(.init.text+0x52a): undefined reference to `psci_smp_available' This corrects the #ifdef in the psci.h header file to match the Makefile conditional we have for building that function. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Daniel Vetter authored
commit d3e376f5 upstream. This is called without dev->struct_mutex held, we need to use the _unlocked variant. Never caught in the wild since you'd need an evil userspace which races a gem_close ioctl call with the in-progress open. Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Acked-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by:
-
Toshi Kani authored
commit 93f834df upstream. devm_memremap() returns an ERR_PTR() value in case of error. However, it returns NULL when memremap() failed. This causes the caller, such as the pmem driver, to proceed and oops later. Change devm_memremap() to return ERR_PTR(-ENXIO) when memremap() failed. Signed-off-by:
Toshi Kani <toshi.kani@hpe.com> Cc: Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
David Hildenbrand authored
commit 9c7ebb61 upstream. fprs is never freed, therefore resulting in a memory leak if kvm_vcpu_init() fails or the vcpu is destroyed. Fixes: 9977e886 ("s390/kernel: lazy restore fpu registers") Reported-by:
Eric Farman <farman@linux.vnet.ibm.com> Signed-off-by:
-
dann frazier authored
commit 67dfa175 upstream. GCC6 (and Linaro's 2015.12 snapshot of GCC5) has a new default that uses adrp/ldr or adrp/add to address literal pools. When CONFIG_ARM64_ERRATUM_843419 is enabled, modules built with this toolchain fail to load: module libahci: unsupported RELA relocation: 275 This patch fixes the problem by passing '-mpc-relative-literal-loads' to the compiler. Cc: stable@vger.kernel.org Fixes: df057cc7 ("arm64: errata: add module build workaround for erratum #843419") BugLink: http://bugs.launchpad.net/bugs/1533009Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Suggested-by:
Christophe Lyon <christophe.lyon@linaro.org> Signed-off-by:
Dann Frazier <dann.frazier@canonical.com> [will: backport to 4.4-stable] Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
