Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.

The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.

Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.

Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.

So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.

This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n

and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds auto TDLS support to mwifiex.

Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.

So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.

Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.

Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Kalle Valo <kvalo@qca.qualcomm.com> says:

"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:

o fix resume (Bartosz)

o firmware restart is now faster and more reliable (Michal)

o it's now possible to test hardware restart functionality without
  crashing the firmware using hw-restart parameter with
  simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.

To record tx ieee80211 headers

     trace-cmd record -e ath10k_tx_hdr

To record complete packets

     trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While preparing an ad-hoc start command, the capability info bitmap is
needlessly set from the command, and then the ESS bit cleared.

Change to set the bitmap directly without reference to the command.
Signed-off-by: James Cameron <quozl@laptop.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The wlcore_cmd_send_failsafe() function is only called in the cmd.c
file, where it is definde.  Make it static.

Additionally, move the EXPORT_SYMBOL macro for wl1271_cmd_send() to
the right place.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check for the minimum required buffer length in wlcore_cmd_send() and
wlcore_cmd_configure_failsafe.  This ensures that we will never try to
use a buffer that is smaller than the required header.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It's been observed that wrong firmware version (ex. 66.14.96.p9
instead of 14.66.9.p96) is displayed on big endian platforms.

The problem is fixed here.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

use code provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

use values provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For some reason it didn't coused obvious problems.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

not sure why.
Initially provided by Ashish Patro <patro@cs.wisc.edu>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

and rename exports from ath9k_spectral_* to ath9k_cmn_spectral_*
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now we should be ready to make this code common.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

last preparation before moving ath9k_spectral_scan_ to spectral.c
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>