commit 597c56e3 upstream.

This change fixes a data corruption issue occurred on USB hard disk for
the case that bounce buffer is used during transferring data.

While updating data between sg list and bounce buffer, current
implementation passes mapped sg number (urb->num_mapped_sgs) to
sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data
not get copied if target buffer is located in the elements after
mapped sg elements. This change passes sg number for full list to
fix issue.

Besides, for copying data from bounce buffer, calling dma_unmap_single()
on the bounce buffer before copying data to sg list can avoid cache issue.

Fixes: f9c589e1 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ef4d6f6b upstream.

The ror32 implementation (word >> shift) | (word << (32 - shift) has
undefined behaviour if shift is outside the [1, 31] range.  Similarly
for the 64 bit variants.  Most callers pass a compile-time constant
(naturally in that range), but there's an UBSAN report that these may
actually be called with a shift count of 0.

Instead of special-casing that, we can make them DTRT for all values of
shift while also avoiding UB.  For some reason, this was already partly
done for rol32 (which was well-defined for [0, 31]).  gcc 8 recognizes
these patterns as rotates, so for example

  __u32 rol32(__u32 word, unsigned int shift)
  {
	return (word << (shift & 31)) | (word >> ((-shift) & 31));
  }

compiles to

0000000000000020 <rol32>:
  20:   89 f8                   mov    %edi,%eax
  22:   89 f1                   mov    %esi,%ecx
  24:   d3 c0                   rol    %cl,%eax
  26:   c3                      retq

Older compilers unfortunately do not do as well, but this only affects
the small minority of users that don't pass constants.

Due to integer promotions, ro[lr]8 were already well-defined for shifts
in [0, 8], and ro[lr]16 were mostly well-defined for shifts in [0, 16]
(only mostly - u16 gets promoted to _signed_ int, so if bit 15 is set,
word << 16 is undefined).  For consistency, update those as well.

Link: http://lkml.kernel.org/r/20190410211906.2190-1-linux@rasmusvillemoes.dkSigned-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Cc: Vadim Pasternak <vadimp@mellanox.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d3c976c1 upstream.

Previously, %g2 would end up with the value PAGE_SIZE, but after the
commit mentioned below it ends up with the value 1 due to being reused
for a different purpose. We need it to be PAGE_SIZE as we use it to step
through pages in our demap loop, otherwise we set different flags in the
low 12 bits of the address written to, thereby doing things other than a
nucleus page flush.

Fixes: a74ad5e6 ("sparc64: Handle extremely large kernel TLB range flushes more gracefully.")
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: James Clarke <jrtc27@jrtc27.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 526f5b85 upstream.

Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 7e27e8d6
("tipc: switch order of device registration to fix a crash")

Because sock_create_kern(net, AF_TIPC, ...) called by
tipc_topsrv_create_listener() in the initialization process
of tipc_init_net(), so tipc_socket_init() must be execute before that.
Meanwhile, tipc_net_id need to be initialized when sock_create()
called, and tipc_socket_init() is no need to be called for each namespace.

I add a variable tipc_topsrv_net_ops, and split the
register_pernet_subsys() of tipc into two parts, and split
tipc_socket_init() with initialization of pernet params.

By the way, I fixed resources rollback error when tipc_bcast_init()
failed in tipc_init_net().

Fixes: 7e27e8d6 ("tipc: switch order of device registration to fix a crash")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com
Reviewed-by: Kang Zhou <zhoukang7@huawei.com>
Reviewed-by: Suanming Mou <mousuanming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5593530e upstream.

This reverts commit 532b0f7e.

More revisions coming up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7681f31e upstream.

There is no need for this at all. Worst it means that if
the guest tries to write to BARs it could lead (on certain
platforms) to PCI SERR errors.

Please note that with af6fc858
"xen-pciback: limit guest control of command register"
a guest is still allowed to enable those control bits (safely), but
is not allowed to disable them and that therefore a well behaved
frontend which enables things before using them will still
function correctly.

This is done via an write to the configuration register 0x4 which
triggers on the backend side:
command_write
  \- pci_enable_device
     \- pci_enable_device_flags
        \- do_pci_enable_device
           \- pcibios_enable_device
              \-pci_enable_resourcess
                [which enables the PCI_COMMAND_MEMORY|PCI_COMMAND_IO]

However guests (and drivers) which don't do this could cause
problems, including the security issues which XSA-120 sought
to address.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e9666d10 upstream.

Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".

The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:

  #if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
  # define HAVE_JUMP_LABEL
  #endif

We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.

Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
[nc: Fix trivial conflicts in 4.19
     arch/xtensa/kernel/jump_label.c doesn't exist yet
     Ensured CC_HAVE_ASM_GOTO and HAVE_JUMP_LABEL were sufficiently
     eliminated]
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 81b45683 upstream.

__compiletime_assert_fallback() is supposed to stop building earlier
by using the negative-array-size method in case the compiler does not
support "error" attribute, but has never worked like that.

You can simply try:

    BUILD_BUG_ON(1);

GCC immediately terminates the build, but Clang does not report
anything because Clang does not support the "error" attribute now.
It will later fail at link time, but __compiletime_assert_fallback()
is not working at least.

The root cause is commit 1d6a0d19 ("bug.h: prevent double evaluation
of `condition' in BUILD_BUG_ON").  Prior to that commit, BUILD_BUG_ON()
was checked by the negative-array-size method *and* the link-time trick.
Since that commit, the negative-array-size is not effective because
'__cond' is no longer constant.  As the comment in <linux/build_bug.h>
says, GCC (and Clang as well) only emits the error for obvious cases.

When '__cond' is a variable,

    ((void)sizeof(char[1 - 2 * __cond]))

... is not obvious for the compiler to know the array size is negative.

Reverting that commit would break BUILD_BUG() because negative-size-array
is evaluated before the code is optimized out.

Let's give up __compiletime_assert_fallback().  This commit does not
change the current behavior since it just rips off the useless code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8bd66d14 upstream.

asm_volatile_goto should also be defined for other compilers that support
asm goto.

Fixes commit 815f0ddb ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive").
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 357d065a upstream.

VMX ghash was using a fallback that did not support interleaving simd
and nosimd operations, leading to failures in the extended test suite.

If I understood correctly, Eric's suggestion was to use the same
data format that the generic code uses, allowing us to call into it
with the same contexts. I wasn't able to get that to work - I think
there's a very different key structure and data layout being used.

So instead steal the arm64 approach and perform the fallback
operations directly if required.

Fixes: cc333cd6 ("crypto: vmx - Adding GHASH routines for VMX module")
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c3f4a6c3 ]

On device surprise removal path (the notifier) we can't
bail just because the features are disabled.  They may
have been enabled during the lifetime of the device.
This bug leads to leaking netdev references and
use-after-frees if there are active connections while
device features are cleared.

Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3686637e ]

TLS offload drivers shouldn't (and currently don't) block
the TLS offload feature changes based on whether there are
active offloaded connections or not.

This seems to be a good idea, because we want the admin to
be able to disable the TLS offload at any time, and there
is no clean way of disabling it for active connections
(TX side is quite problematic).  So if features are cleared
existing connections will stay offloaded until they close,
and new connections will not attempt offload to a given
device.

However, the offload state removal handling is currently
broken if feature flags get cleared while there are
active TLS offloads.

RX side will completely bail from cleanup, even on normal
remove path, leaving device state dangling, potentially
causing issues when the 5-tuple is reused.  It will also
fail to release the netdev reference.

Remove the RX-side warning message, in next release cycle
it should be printed when features are disabled, rather
than when connection dies, but for that we need a more
efficient method of finding connection of a given netdev
(a'la BPF offload code).

Fixes: 4799ac81 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 296d5b54 ]

For every RX packet, the driver replenishes all buffers used for that
packet and puts them back into the RX ring and RX aggregation ring.
In one code path where the RX packet has one RX buffer and one or more
aggregation buffers, we missed recycling the aggregation buffer(s) if
we are unable to allocate a new SKB buffer.  This leads to the
aggregation ring slowly running out of buffers over time.  Fix it
by properly recycling the aggregation buffers.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Rakesh Hemnani <rhemnani@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

stmmac_init_chan() needs to be called before stmmac_init_rx_chan() and
stmmac_init_tx_chan(). This is because if PBLx8 is to be used,
"DMA_CH(#i)_Control.PBLx8" needs to be set before programming
"DMA_CH(#i)_TX_Control.TxPBL" and "DMA_CH(#i)_RX_Control.RxPBL".

Fixes: 47f2a9ce ("net: stmmac: dma channel init prepared for multiple queues")
Reviewed-by: Zhang, Baoli <baoli.zhang@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c0194e2d ]

When CQE compression is enabled (Multi-host systems), compressed CQEs
might arrive to the driver rx, compressed CQEs don't have a valid hash
offload and the driver already reports a hash value of 0 and invalid hash
type on the skb for compressed CQEs, but this is not good enough.

On a congested PCIe, where CQE compression will kick in aggressively,
gro will deliver lots of out of order packets due to the invalid hash
and this might cause a serious performance drop.

The only valid solution, is to disable rxhash offload at all when CQE
compression is favorable (Multi-host systems).

Fixes: 7219ab34 ("net/mlx5e: CQE compression")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 25fa506b ]

root ns is yet another fs core node which is freed using kfree() by
tree_put_node().
Rest of the other fs core objects are also allocated using kmalloc
variants.

However, root ns memory is allocated using kvzalloc().
Hence allocate root ns memory using kzalloc().

Fixes: 25302363 ("net/mlx5_core: Flow steering tree initialization")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

TLV_SET is called with a data pointer and a len parameter that tells us
how many bytes are pointed to by data. When invoking memcpy() we need
to careful to only copy len bytes.

Previously we would copy TLV_LENGTH(len) bytes which would copy an extra
4 bytes past the end of the data pointer which newer GCC versions
complain about.

 In file included from test.c:17:
 In function 'TLV_SET',
     inlined from 'test' at test.c:186:5:
 /usr/include/linux/tipc_config.h:317:3:
 warning: 'memcpy' forming offset [33, 36] is out of the bounds [0, 32]
 of object 'bearer_name' with type 'char[32]' [-Warray-bounds]
     memcpy(TLV_DATA(tlv_ptr), data, tlv_len);
     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 test.c: In function 'test':
 test.c::161:10: note:
 'bearer_name' declared here
     char bearer_name[TIPC_MAX_BEARER_NAME];
          ^~~~~~~~~~~

We still want to ensure any padding bytes at the end are initialised, do
this with a explicit memset() rather than copy bytes past the end of
data. Apply the same logic to TCM_SET.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9414277a ]

In below code flow, for ingress acl table root ns memory leads
to double free.

mlx5_init_fs
  init_ingress_acls_root_ns()
    init_ingress_acl_root_ns
       kfree(steering->esw_ingress_root_ns);
       /* steering->esw_ingress_root_ns is not marked NULL */
  mlx5_cleanup_fs
    cleanup_ingress_acls_root_ns
       steering->esw_ingress_root_ns non NULL check passes.
       kfree(steering->esw_ingress_root_ns);
       /* double free */

Similar issue exist for other tables.

Hence zero out the pointers to not process the table again.

Fixes: 9b93ab98 ("net/mlx5: Separate ingress/egress namespaces for each vport")
Fixes: 40c3eebb49e51 ("net/mlx5: Add support in RDMA RX steering")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ad70411a ]

When disconnecting cdc_ncm the kernel sporadically crashes shortly
after the disconnect:

  [   57.868812] Unable to handle kernel NULL pointer dereference at virtual address 00000000
  ...
  [   58.006653] PC is at 0x0
  [   58.009202] LR is at call_timer_fn+0xec/0x1b4
  [   58.013567] pc : [<0000000000000000>] lr : [<ffffff80080f5130>] pstate: 00000145
  [   58.020976] sp : ffffff8008003da0
  [   58.024295] x29: ffffff8008003da0 x28: 0000000000000001
  [   58.029618] x27: 000000000000000a x26: 0000000000000100
  [   58.034941] x25: 0000000000000000 x24: ffffff8008003e68
  [   58.040263] x23: 0000000000000000 x22: 0000000000000000
  [   58.045587] x21: 0000000000000000 x20: ffffffc68fac1808
  [   58.050910] x19: 0000000000000100 x18: 0000000000000000
  [   58.056232] x17: 0000007f885aff8c x16: 0000007f883a9f10
  [   58.061556] x15: 0000000000000001 x14: 000000000000006e
  [   58.066878] x13: 0000000000000000 x12: 00000000000000ba
  [   58.072201] x11: ffffffc69ff1db30 x10: 0000000000000020
  [   58.077524] x9 : 8000100008001000 x8 : 0000000000000001
  [   58.082847] x7 : 0000000000000800 x6 : ffffff8008003e70
  [   58.088169] x5 : ffffffc69ff17a28 x4 : 00000000ffff138b
  [   58.093492] x3 : 0000000000000000 x2 : 0000000000000000
  [   58.098814] x1 : 0000000000000000 x0 : 0000000000000000
  ...
  [   58.205800] [<          (null)>]           (null)
  [   58.210521] [<ffffff80080f5298>] expire_timers+0xa0/0x14c
  [   58.215937] [<ffffff80080f542c>] run_timer_softirq+0xe8/0x128
  [   58.221702] [<ffffff8008081120>] __do_softirq+0x298/0x348
  [   58.227118] [<ffffff80080a6304>] irq_exit+0x74/0xbc
  [   58.232009] [<ffffff80080e17dc>] __handle_domain_irq+0x78/0xac
  [   58.237857] [<ffffff8008080cf4>] gic_handle_irq+0x80/0xac
  ...

The crash happens roughly 125..130ms after the disconnect. This
correlates with the 'delay' timer that is started on certain USB tx/rx
errors in the URB completion handler.

The problem is a race of usbnet_stop() with usbnet_start_xmit(). In
usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in
flight. This only makes sense if no new URBs are submitted
concurrently, though. But the usbnet_start_xmit() can run at the same
time on another CPU which almost unconditionally submits an URB. The
error callback of the new URB will then schedule the timer after it was
already stopped.

The fix adds a check if the tx queue is stopped after the tx list lock
has been taken. This should reliably prevent the submission of new URBs
while usbnet_terminate_urbs() does its job. The same thing is done on
the rx side even though it might be safe due to other flags that are
checked there.
Signed-off-by: Jan Klötzke <Jan.Kloetzke@preh.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 49ce881c ]

Commit 984203ce ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.

This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.

Fixes: 984203ce ("net: stmmac: mdio: remove reset gpio free")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4097e9d2 ]

Function tcf_action_dump() relies on tc_action->order field when starting
nested nla to send action data to userspace. This approach breaks in
several cases:

- When multiple filters point to same shared action, tc_action->order field
  is overwritten each time it is attached to filter. This causes filter
  dump to output action with incorrect attribute for all filters that have
  the action in different position (different order) from the last set
  tc_action->order value.

- When action data is displayed using tc action API (RTM_GETACTION), action
  order is overwritten by tca_action_gd() according to its position in
  resulting array of nl attributes, which will break filter dump for all
  filters attached to that shared action that expect it to have different
  order value.

Don't rely on tc_action->order when dumping actions. Set nla according to
action position in resulting array of actions instead.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3d3ced2e ]

Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected.  Warn the user when the
PHY fails to boot the firmware and refuse to initialise.

Fixes: 20b2af32 ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 21808437 ]

MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but
the current code is passing the global tx queue offset, so it ends
up writing to unknown registers (between 0x8280 and 0x82fc, which
seemed to be unused by the hardware). This fixes the issue by using
the logical queue id instead.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d484e06e ]

Fix below issues in err code path of probe:
1. we don't need to unregister_netdev() because the netdev isn't
registered.
2. when register_netdev() fails, we also need to destroy bm pool for
HWBM case.

Fixes: dc35a10f ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a4270d67 ]

If a network driver provides to napi_gro_frags() an
skb with a page fragment of exactly 14 bytes, the call
to gro_pull_from_frag0() will 'consume' the fragment
by calling skb_frag_unref(skb, 0), and the page might
be freed and reused.

Reading eth->h_proto at the end of napi_frags_skb() might
read mangled data, or crash under specific debugging features.

BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline]
BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841
Read of size 2 at addr ffff88809366840c by task syz-executor599/8957

CPU: 1 PID: 8957 Comm: syz-executor599 Not tainted 5.2.0-rc1+ #32
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188
 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 kasan_report+0x12/0x20 mm/kasan/common.c:614
 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:142
 napi_frags_skb net/core/dev.c:5833 [inline]
 napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841
 tun_get_user+0x2f3c/0x3ff0 drivers/net/tun.c:1991
 tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2037
 call_write_iter include/linux/fs.h:1872 [inline]
 do_iter_readv_writev+0x5f8/0x8f0 fs/read_write.c:693
 do_iter_write fs/read_write.c:970 [inline]
 do_iter_write+0x184/0x610 fs/read_write.c:951
 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1015
 do_writev+0x15b/0x330 fs/read_write.c:1058

Fixes: a50e233c ("net-gro: restore frag0 optimization")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ce8d24f9 ]

Fix the clk mismatch in the error path "failed_reset" because
below error path will disable clk_ahb and clk_ipg directly, it
should use pm_runtime_put_noidle() instead of pm_runtime_put()
to avoid to call runtime resume callback.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 84b3fd1f ]

Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends
up in bits 47:32 of the return value, instead of bits 31:16 as they
should.

Fixes: 6e46e2d8 ("net: dsa: mv88e6xxx: Fix u64 statistics")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8fb44d60 ]

If llc_mac_hdr_init() returns an error, we must drop the skb
since no llc_build_and_send_ui_pkt() caller will take care of this.

BUG: memory leak
unreferenced object 0xffff8881202b6800 (size 2048):
  comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.590s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    1a 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00  ...@............
  backtrace:
    [<00000000e25b5abe>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
    [<00000000e25b5abe>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<00000000e25b5abe>] slab_alloc mm/slab.c:3326 [inline]
    [<00000000e25b5abe>] __do_kmalloc mm/slab.c:3658 [inline]
    [<00000000e25b5abe>] __kmalloc+0x161/0x2c0 mm/slab.c:3669
    [<00000000a1ae188a>] kmalloc include/linux/slab.h:552 [inline]
    [<00000000a1ae188a>] sk_prot_alloc+0xd6/0x170 net/core/sock.c:1608
    [<00000000ded25bbe>] sk_alloc+0x35/0x2f0 net/core/sock.c:1662
    [<000000002ecae075>] llc_sk_alloc+0x35/0x170 net/llc/llc_conn.c:950
    [<00000000551f7c47>] llc_ui_create+0x7b/0x140 net/llc/af_llc.c:173
    [<0000000029027f0e>] __sock_create+0x164/0x250 net/socket.c:1430
    [<000000008bdec225>] sock_create net/socket.c:1481 [inline]
    [<000000008bdec225>] __sys_socket+0x69/0x110 net/socket.c:1523
    [<00000000b6439228>] __do_sys_socket net/socket.c:1532 [inline]
    [<00000000b6439228>] __se_sys_socket net/socket.c:1530 [inline]
    [<00000000b6439228>] __x64_sys_socket+0x1e/0x30 net/socket.c:1530
    [<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
    [<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

BUG: memory leak
unreferenced object 0xffff88811d750d00 (size 224):
  comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.600s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 f0 0c 24 81 88 ff ff 00 68 2b 20 81 88 ff ff  ...$.....h+ ....
  backtrace:
    [<0000000053026172>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
    [<0000000053026172>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<0000000053026172>] slab_alloc_node mm/slab.c:3269 [inline]
    [<0000000053026172>] kmem_cache_alloc_node+0x153/0x2a0 mm/slab.c:3579
    [<00000000fa8f3c30>] __alloc_skb+0x6e/0x210 net/core/skbuff.c:198
    [<00000000d96fdafb>] alloc_skb include/linux/skbuff.h:1058 [inline]
    [<00000000d96fdafb>] alloc_skb_with_frags+0x5f/0x250 net/core/skbuff.c:5327
    [<000000000a34a2e7>] sock_alloc_send_pskb+0x269/0x2a0 net/core/sock.c:2225
    [<00000000ee39999b>] sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2242
    [<00000000e034d810>] llc_ui_sendmsg+0x10a/0x540 net/llc/af_llc.c:933
    [<00000000c0bc8445>] sock_sendmsg_nosec net/socket.c:652 [inline]
    [<00000000c0bc8445>] sock_sendmsg+0x54/0x70 net/socket.c:671
    [<000000003b687167>] __sys_sendto+0x148/0x1f0 net/socket.c:1964
    [<00000000922d78d9>] __do_sys_sendto net/socket.c:1976 [inline]
    [<00000000922d78d9>] __se_sys_sendto net/socket.c:1972 [inline]
    [<00000000922d78d9>] __x64_sys_sendto+0x2a/0x30 net/socket.c:1972
    [<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
    [<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 31680ac2 ]

IPv6 redirect is broken for VRF. __ip6_route_redirect walks the FIB
entries looking for an exact match on ifindex. With VRF the flowi6_oif
is updated by l3mdev_update_flow to the l3mdev index and the
FLOWI_FLAG_SKIP_NH_OIF set in the flags to tell the lookup to skip the
device match. For redirects the device match is requires so use that
flag to know when the oif needs to be reset to the skb device index.

Fixes: ca254490 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 72f7cfab ]

IPv6 does not consider if the socket is bound to a device when binding
to an address. The result is that a socket can be bound to eth0 and
then bound to the address of eth1. If the device is a VRF, the result
is that a socket can only be bound to an address in the default VRF.

Resolve by considering the device if sk_bound_dev_if is set.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 903869bd ]

ip_sf_list_clear_all() needs to be defined even if !CONFIG_IP_MULTICAST

Fixes: 3580d04a ("ipv4/igmp: fix another memory leak in igmpv3_del_delrec()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3580d04a ]

syzbot reported memory leaks [1] that I have back tracked to
a missing cleanup from igmpv3_del_delrec() when
(im->sfmode != MCAST_INCLUDE)

Add ip_sf_list_clear_all() and kfree_pmc() helpers to explicitely
handle the cleanups before freeing.

[1]

BUG: memory leak
unreferenced object 0xffff888123e32b00 (size 64):
  comm "softirq", pid 0, jiffies 4294942968 (age 8.010s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 e0 00 00 01 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<000000006105011b>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
    [<000000006105011b>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<000000006105011b>] slab_alloc mm/slab.c:3326 [inline]
    [<000000006105011b>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553
    [<000000004bba8073>] kmalloc include/linux/slab.h:547 [inline]
    [<000000004bba8073>] kzalloc include/linux/slab.h:742 [inline]
    [<000000004bba8073>] ip_mc_add1_src net/ipv4/igmp.c:1961 [inline]
    [<000000004bba8073>] ip_mc_add_src+0x36b/0x400 net/ipv4/igmp.c:2085
    [<00000000a46a65a0>] ip_mc_msfilter+0x22d/0x310 net/ipv4/igmp.c:2475
    [<000000005956ca89>] do_ip_setsockopt.isra.0+0x1795/0x1930 net/ipv4/ip_sockglue.c:957
    [<00000000848e2d2f>] ip_setsockopt+0x3b/0xb0 net/ipv4/ip_sockglue.c:1246
    [<00000000b9db185c>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616
    [<000000003028e438>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130
    [<0000000015b65589>] __sys_setsockopt+0x98/0x120 net/socket.c:2078
    [<00000000ac198ef0>] __do_sys_setsockopt net/socket.c:2089 [inline]
    [<00000000ac198ef0>] __se_sys_setsockopt net/socket.c:2086 [inline]
    [<00000000ac198ef0>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086
    [<000000000a770437>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
    [<00000000d3adb93b>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 9c8bb163 ("igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit df453700 ]

According to Amit Klein and Benny Pinkas, IP ID generation is too weak
and might be used by attackers.

Even with recent net_hash_mix() fix (netns: provide pure entropy for net_hash_mix())
having 64bit key and Jenkins hash is risky.

It is time to switch to siphash and its 128bit keys.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b5730061 ]

VLAN flows never get offloaded unless ivlan_vld is set in filter spec.
It's not compulsory for vlan_ethtype to be set.

So, always enable ivlan_vld bit for offloading VLAN flows regardless of
vlan_ethtype is set or not.

Fixes: ad9af3e0 (cxgb4: add tc flower match support for vlan)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 33403121 ]

Once in a while, with just the right timing, 802.3ad slaves will fail to
properly initialize, winding up in a weird state, with a partner system
mac address of 00:00:00:00:00:00. This started happening after a fix to
properly track link_failure_count tracking, where an 802.3ad slave that
reported itself as link up in the miimon code, but wasn't able to get a
valid speed/duplex, started getting set to BOND_LINK_FAIL instead of
BOND_LINK_DOWN. That was the proper thing to do for the general "my link
went down" case, but has created a link initialization race that can put
the interface in this odd state.

The simple fix is to instead set the slave link to BOND_LINK_DOWN again,
if the link has never been up (last_link_up == 0), so the link state
doesn't bounce from BOND_LINK_DOWN to BOND_LINK_FAIL -- it hasn't failed
in this case, it simply hasn't been up yet, and this prevents the
unnecessary state change from DOWN to FAIL and getting stuck in an init
failure w/o a partner mac.

Fixes: ea53abfa ("bonding/802.3ad: fix link_failure_count tracking")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Tested-by: Heesoon Kim <Heesoon.Kim@stratus.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c260121a ]

Now that nfs_match_client drops the nfs_client_lock, we should be
careful
to always return it in the same condition: locked.

Fixes: 950a578c ("NFS: make nfs_match_client killable")
Reported-by: syzbot+228a82b263b5da91883d@syzkaller.appspotmail.com
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit efa31801 ]

The Allwinner BSP makes sure that we don't end up with a null start delay
or with a delay larger than vtotal.

The former condition is likely to happen now with the reworked start delay,
so make sure we enforce the same boundaries.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c9889cf5f7a3d101ef380905900b45a182596f56.1549896081.git-series.maxime.ripard@bootlin.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d1ffa760 ]

The quiesce function calls cio_cancel_halt_clear() and if we
get an -EBUSY we go into a loop where we:
	- wait for any interrupts
	- flush all I/O in the workqueue
	- retry cio_cancel_halt_clear

During the period where we are waiting for interrupts or
flushing all I/O, the channel subsystem could have completed
a halt/clear action and turned off the corresponding activity
control bits in the subchannel status word. This means the next
time we call cio_cancel_halt_clear(), we will again start by
calling cancel subchannel and so we can be stuck between calling
cancel and halt forever.

Rather than calling cio_cancel_halt_clear() immediately after
waiting, let's try to disable the subchannel. If we succeed in
disabling the subchannel then we know nothing else can happen
with the device.
Suggested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <4d5a4b98ab1b41ac6131b5c36de18b76c5d66898.1555449329.git.alifm@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>