These are internal static functions to genpd. Let's conform to the naming
rules, by dropping the "pm_" prefix from these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Measure latency does by itself contribute to an increased latency, thus we
should avoid it when it isn't needed.

Currently genpd measures latencies in the system PM phase for the
->power_on|off() callbacks, except in the syscore case when it's not
allowed to use ktime_get() as timekeeping may be suspended.

Since there should be plenty of occasions during runtime PM to perform
these measurements, let's rely on that and drop them from system PM. This
will also make it consistent for how measurements are done of the runtime
PM callbacks (as those may be invoked during system PM).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In cases when the PM domain haven't assigned a system PM callback, the PM
core fall-backs to check for the callback at the driver level instead.
This makes it redundant to assign a pm_generic_* helper function to a
corresponding system PM callback at a PM domain level.

Therefore, let's remove these assignments in pm_genpd_init().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

There's no need to validate the PM domain by using genpd_lookup_dev() when
removing the device via genpd's genpd_dev_pm_detach() function. That's
because this function can't be called, unless there is a valid PM domain
for the device.

To simplify the behaviour, let's move code from pm_genpd_remove_device()
into a new internal function, genpd_remove_device(), which is called from
pm_genpd_remove_device() and genpd_dev_pm_detach().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In platforms such as Rockchip's, the array of domains isn't always
filled without holes, as which domains are present depend on the
particular SoC revision.

By allowing holes to be in the array, such SoCs can still use a single
set of constants to index the array of power domains.

Fixes: 0159ec67 (PM / Domains: Verify the PM domain is present when adding a provider)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If a device supports PM domains that are subdomains of another PM
domain, then the PM domains should be removed in reverse order to
ensure that the subdomains are removed first. Furthermore, if there is
more than one provider, then there needs to be a way to remove the
domains in reverse order for a specific provider.

Add the function of_genpd_remove_last() to remove the last PM domain
added by a given PM domain provider and return the generic_pm_domain
structure for the PM domain that was removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The genpd framework allows users to add PM domains via the pm_genpd_init()
function, however, there is no corresponding function to remove a PM
domain. For most devices this may be fine as the PM domains are never
removed, however, for devices that wish to populate the PM domains from
within a driver, having the ability to remove a PM domain if the probing
of the device fails or the driver is unloaded is necessary.

Add the function pm_genpd_remove() to remove a PM domain by referencing
it's generic_pm_domain structure. Note that the bulk of the code that
removes the PM domain is placed in a separate local function
genpd_remove() (which is called by pm_genpd_remove()). The code is
structured in this way to prepare for adding another function to remove
a PM domain by provider that will also call genpd_remove(). Note that
users of genpd_remove() must call this function with the mutex,
gpd_list_lock, held.

PM domains can only be removed if the associated provider has been
removed, they are not a parent domain to another PM domain and have no
devices associated with them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

It is possible that a device has more than one provider of PM domains
and to support the removal of a PM domain by provider, it is necessary
to store a reference to the provider in the PM domain structure.
Therefore, store a reference to the firmware node handle in the PM
domain structure and populate it when providers (only device-tree based
providers are currently supported by PM domains) are registered.

Please note that when removing PM domains, it is necessary to verify
that the PM domain provider has been removed from the list of providers
before the PM domain can be removed. To do this add another member to
the PM domain structure that indicates if the provider is present and
set this member accordingly when providers are added and removed.

Initialise the 'provider' and 'has_provider' members of the
generic_pm_domain structure when a PM domains is added by calling
pm_genpd_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In order to remove PM domains safely from the list of PM domains,
it is necessary to adding locking for the PM domain list around any
places where devices or subdomains are added to a PM domain.

There are places where a reference to a PM domain is obtained via
calling of_genpd_get_from_provider() before adding the device or the
subdomain. In these cases a lock for the PM domain list needs to be
held around the call to of_genpd_get_from_provider() and the call to
add the device/subdomain. To avoid deadlocks by multiple attempts to
obtain the PM domain list lock, add functions genpd_add_device() and
genpd_add_subdomain() which require the user to hold the PM domain
list lock when calling.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When a PM domain provider is added, there is currently no way to tell if
any PM domains associated with the provider are present. Naturally, the
PM domain provider should not be registered if the PM domains have not
been added. Nonetheless, verify that the PM domain(s) associated with a
provider are present when registering the PM domain provider.

This change adds a dependency on the function pm_genpd_present() when
CONFIG_PM_GENERIC_DOMAINS_OF is enabled and so ensure this function is
available when CONFIG_PM_GENERIC_DOMAINS_OF selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Functions __of_genpd_xlate_simple(), __of_genpd_xlate_onecell() and
__of_genpd_add_provider() are not used outside of the core generic PM
domain code. Therefore, reduce the number of APIs exposed by making
these static. At the same time don't expose the typedef for
genpd_xlate_t either and make this a local definition as well.

The functions are renamed to follow the naming conventions for static
functions in the generic PM domain core.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

There should be no need to expose the generic_pm_domain structure to
clients and this eliminates the need to implement reference counting for
any external reference to a PM domain. Therefore, make the functions
pm_genpd_lookup_dev() and of_genpd_get_from_provider() private to the
PM domain core. The functions are renamed in accordance with the naming
conventions for genpd static functions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Update the staging/board PM domain code to use the
of_genpd_add_subdomain() and remove any calls to
of_genpd_get_from_provider().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Update the EXYNOS PM domain code to use the of_genpd_add_subdomain()
and remove any calls to of_genpd_get_from_provider().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Ideally, if we are returning a reference to a PM domain via a call to
of_genpd_get_from_provider(), then we should keep track of such
references via a reference count. The reference count could then be used
to determine if a PM domain can be safely removed. Alternatively, it is
possible to avoid such external references by providing APIs to access
the PM domain and hence, eliminate any calls to
of_genpd_get_from_provider().

Add new helper functions for adding a device and a subdomain to a PM
domain when using device-tree, so that external calls to
of_genpd_get_from_provider() can be removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Debugfs support for PM domains is only enabled if both CONFIG_PM_DEBUG
and CONFIG_PM_ADVANCED_DEBUG are enabled. CONFIG_PM_ADVANCED_DEBUG is
described as "extra PM attributes in sysfs for low-level
debugging/testing" which does not seem related.

Given that the debugfs for PM domains only allows users to view the
state of the PM domains, always enable debugfs support for PM domains
if PM domains and debugfs support is enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull more block fixes from Jens Axboe:
 "As mentioned in the pull the other day, a few more fixes for this
  round, all related to the bio op changes in this series.

  Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf.  I
  wanted to do that change right after or right before -rc1, so that
  risk of conflict was reduced.  I just rebased the series on top of
  current master, and no new ->bi_rw usage has snuck in"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: rename bio bi_rw to bi_opf
  target: iblock_execute_sync_cache() should use bio_set_op_attrs()
  mm: make __swap_writepage() use bio_set_op_attrs()
  block/mm: make bdev_ops->rw_page() take a bool for read/write

Pull drm zpos property support from Dave Airlie:
 "This tree was waiting on some media stuff I hadn't had time to get a
  stable branchpoint off, so I just waited until it was all in your tree
  first.

  It's been around a bit on the list and shouldn't affect anything
  outside adding the generic API and moving some ARM drivers to using
  it"

* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
  drm: rcar: use generic code for managing zpos plane property
  drm/exynos: use generic code for managing zpos plane property
  drm: sti: use generic zpos for plane
  drm: add generic zpos property

Since commit 63a4cc24, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.

No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>

The original commit missed this function, it needs to mark it a
write flush.

Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>

Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: Jens Axboe <axboe@fb.com>

Commit abf54548 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.

Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Pull documentation fixes from Jonathan Corbet:
 "Three fixes for the docs build, including removing an annoying warning
  on 'make help' if sphinx isn't present"

* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
  DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
  Documenation: update cgroup's document path
  Documentation/sphinx: do not warn about missing tools in 'make help'

Pull binfmt_misc update from James Bottomley:
 "This update is to allow architecture emulation containers to function
  such that the emulation binary can be housed outside the container
  itself.  The container and fs parts both have acks from relevant
  experts.

  To use the new feature you have to add an F option to your binfmt_misc
  configuration"

From the docs:
 "The usual behaviour of binfmt_misc is to spawn the binary lazily when
  the misc format file is invoked.  However, this doesn't work very well
  in the face of mount namespaces and changeroots, so the F mode opens
  the binary as soon as the emulation is installed and uses the opened
  image to spawn the emulator, meaning it is always available once
  installed, regardless of how the environment changes"

* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
  binfmt_misc: add F option description to documentation
  binfmt_misc: add persistent opened binary handler for containers
  fs: add filp_clone_open API

In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.

So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs updates from Al Viro:
 "Assorted cleanups and fixes.

  In the "trivial API change" department - ->d_compare() losing 'parent'
  argument"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  cachefiles: Fix race between inactivating and culling a cache object
  9p: use clone_fid()
  9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
  vfs: make dentry_needs_remove_privs() internal
  vfs: remove file_needs_remove_privs()
  vfs: fix deadlock in file_remove_privs() on overlayfs
  get rid of 'parent' argument of ->d_compare()
  cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
  affs ->d_compare(): don't bother with ->d_inode
  fold _d_rehash() and __d_rehash() together
  fold dentry_rcuwalk_invalidate() into its only remaining caller

Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs

Pull more xfs updates from Dave Chinner:
 "This is the second part of the XFS updates for this merge cycle, and
  contains the new reverse block mapping feature for XFS.

  Reverse mapping allows us to track the owner of a specific block on
  disk precisely.  It is implemented as a set of btrees (one per
  allocation group) that track the owners of allocated extents.
  Effectively it is a "used space tree" that is updated when we allocate
  or free extents.  i.e. it is coherent with the free space btrees we
  already maintain and never overlaps with them.

  This reverse mapping infrastructure is the building block of several
  upcoming features - reflink, copy-on-write data, dedupe, online
  metadata and data scrubbing, highly accurate bad sector/data loss
  reporting to users, and significantly improved reconstruction of
  damaged and corrupted filesystems.  There's a lot of new stuff coming
  along in the next couple of cycles,a nd it all builds in the rmap
  infrastructure.

  As such, it's a huge chunk of new code with new on-disk format
  features and internal infrastructure.  It warns at mount time as an
  experimental feature and that it may eat data (as we do with all new
  on-disk features until they stabilise).  We have not released
  userspace suport for it yet - userspace support currently requires
  download from Darrick's xfsprogs repo and build from source, so the
  access to this feature is really developer/tester only at this point.
  Initial userspace support will be released at the same time kernel
  with this code in it is released.

  The new rmap enabled code regresses 3 xfstests - all are ENOSPC
  related corner cases, one of which Darrick posted a fix for a few
  hours ago.  The other two are fixed by infrastructure that is part of
  the upcoming reflink patchset.  This new ENOSPC infrastructure
  requires a on-disk format tweak required to keep mount times in
  check - we need to keep an on-disk count of allocated rmapbt blocks so
  we don't have to scan the entire btrees at mount time to count them.

  This is currently being tested and will be part of the fixes sent in
  the next week or two so users will not be exposed to this change"

* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
  xfs: move (and rename) the deferred bmap-free tracepoints
  xfs: collapse single use static functions
  xfs: remove unnecessary parentheses from log redo item recovery functions
  xfs: remove the extents array from the rmap update done log item
  xfs: in btree_lshift, only allocate temporary cursor when needed
  xfs: remove unnecesary lshift/rshift key initialization
  xfs: remove the get*keys and update_keys btree ops pointers
  xfs: enable the rmap btree functionality
  xfs: don't update rmapbt when fixing agfl
  xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
  xfs: add rmap btree block detection to log recovery
  xfs: add rmap btree geometry feature flag
  xfs: propagate bmap updates to rmapbt
  xfs: enable the xfs_defer mechanism to process rmaps to update
  xfs: log rmap intent items
  xfs: create rmap update intent log items
  xfs: add rmap btree insert and delete helpers
  xfs: convert unwritten status of reverse mappings
  xfs: remove an extent from the rmap btree
  xfs: add an extent to the rmap btree
  ...

Pull qstr constification updates from Al Viro:
 "Fairly self-contained bunch - surprising lot of places passes struct
  qstr * as an argument when const struct qstr * would suffice; it
  complicates analysis for no good reason.

  I'd prefer to feed that separately from the assorted fixes (those are
  in #for-linus and with somewhat trickier topology)"

* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qstr: constify instances in adfs
  qstr: constify instances in lustre
  qstr: constify instances in f2fs
  qstr: constify instances in ext2
  qstr: constify instances in vfat
  qstr: constify instances in procfs
  qstr: constify instances in fuse
  qstr constify instances in fs/dcache.c
  qstr: constify instances in nfs
  qstr: constify instances in ocfs2
  qstr: constify instances in autofs4
  qstr: constify instances in hfs
  qstr: constify instances in hfsplus
  qstr: constify instances in logfs
  qstr: constify dentry_init_security

Pull mailcap fixlets from Mauro Carvalho Chehab:
 "A small fixup for my and Shuah's entries in .mailcap.

  Basically, those entries were with a syntax that makes
  get_maintainer.pl to do the wrong thing"

* tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  .mailmap: Correct entries for Mauro Carvalho Chehab and Shuah Khan

Pull virtio/vhost updates from Michael Tsirkin:

 - new vsock device support in host and guest

 - platform IOMMU support in host and guest, including compatibility
   quirks for legacy systems.

 - misc fixes and cleanups.

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  VSOCK: Use kvfree()
  vhost: split out vringh Kconfig
  vhost: detect 32 bit integer wrap around
  vhost: new device IOTLB API
  vhost: drop vringh dependency
  vhost: convert pre sorted vhost memory array to interval tree
  vhost: introduce vhost memory accessors
  VSOCK: Add Makefile and Kconfig
  VSOCK: Introduce vhost_vsock.ko
  VSOCK: Introduce virtio_transport.ko
  VSOCK: Introduce virtio_vsock_common.ko
  VSOCK: defer sock removal to transports
  VSOCK: transport-specific vsock_transport functions
  vhost: drop vringh dependency
  vop: pull in vhost Kconfig
  virtio: new feature to detect IOMMU device quirk
  balloon: check the number of available pages in leak balloon
  vhost: lockless enqueuing
  vhost: simplify work flushing

Pull more KVM updates from Paolo Bonzini:
 - ARM bugfix and MSI injection support
 - x86 nested virt tweak and OOPS fix
 - Simplify pvclock code (vdso bits acked by Andy Lutomirski).

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  nvmx: mark ept single context invalidation as supported
  nvmx: remove comment about missing nested vpid support
  KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
  KVM: documentation: fix KVM_CAP_X2APIC_API information
  x86: vdso: use __pvclock_read_cycles
  pvclock: introduce seqcount-like API
  arm64: KVM: Set cpsr before spsr on fault injection
  KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
  KVM: arm/arm64: Enable MSI routing
  KVM: arm/arm64: Enable irqchip routing
  KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
  KVM: irqchip: Convey devid to kvm_set_msi
  KVM: Add devid in kvm_kernel_irq_routing_entry
  KVM: api: Pass the devid in the msi routing entry

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.8.  Also includes is a
  minor SSB cleanup as SSB code traditionally is merged through the MIPS
  tree:

  ATH25:
    - MIPS: Add default configuration for ath25

  Boot:
    - For zboot, copy appended dtb to the end of the kernel
    - store the appended dtb address in a variable

  BPF:
    - Fix off by one error in offset allocation

  Cobalt code:
    - Fix typos

  Core code:
    - debugfs_create_file returns NULL on error, so don't use IS_ERR for
      testing for errors.
    - Fix double locking issue in RM7000 S-cache code.  This would only
      affect RM7000 ARC systems on reboot.
    - Fix page table corruption on THP permission changes.
    - Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
      David says, there are no compatibility issues raised by this fix.
    - Move some signal code around.
    - Rewrite r4k count/compare clockevent device registration such that
      min_delta_ticks/max_delta_ticks files are guaranteed to be
      initialized.
    - Only register r4k count/compare as clockevent device if we can
      assume the clock to be constant.
    - Fix MSA asm warnings in control reg accessors
    - uasm and tlbex fixes and tweaking.
    - Print segment physical address when EU=1.
    - Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
    - CP: Allow booting by VP other than VP 0
    - Cache handling fixes and optimizations for r4k class caches
    - Add hotplug support for R6 processors
    - Cleanup hotplug bits in kconfig
    - traps: return correct si code for accessing nonmapped addresses
    - Remove cpu_has_safe_index_cacheops

  Lantiq:
    - Register IRQ handler for virtual IRQ number
    - Fix EIU interrupt loading code
    - Use the real EXIN count
    - Fix build error.

  Loongson 3:
    - Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES

  Octeon:
    - Delete built-in DTB pruning code for D-Link DSR-1000N.
    - Clean up GPIO definitions in dlink_dsr-1000n.dts.
    - Add more LEDs to the DSR-100n DTS
    - Fix off by one in octeon_irq_gpio_map()
    - Typo fixes
    - Enable SATA by default in cavium_octeon_defconfig
    - Support readq/writeq()
    - Remove forced mappings of USB interrupts.
    - Ensure DMA descriptors are always in the low 4GB
    - Improve USB reset code for OCTEON II.

  Pistachio:
    - Add maintainers entry for pistachio SoC Support
    - Remove plat_setup_iocoherency

  Ralink:
    - Fix pwm UART in spis group pinmux.

  SSB:
    - Change bare unsigned to unsigned int to suit coding style

  Tools:
    - Fix reloc tool compiler warnings.

  Other:
    - Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
  MIPS: mm: Fix definition of R6 cache instruction
  MIPS: tools: Fix relocs tool compiler warnings
  MIPS: Cobalt: Fix typo
  MIPS: Octeon: Fix typo
  MIPS: Lantiq: Fix build failure
  MIPS: Use CPHYSADDR to implement mips32 __pa
  MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
  MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
  MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
  MIPS: store the appended dtb address in a variable
  MIPS: ZBOOT: copy appended dtb to the end of the kernel
  MIPS: ralink: fix spis group pinmux
  MIPS: Factor o32 specific code into signal_o32.c
  MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
  MIPS: Use per-mm page to execute branch delay slot instructions
  MIPS: Modify error handling
  MIPS: c-r4k: Use SMP calls for CM indexed cache ops
  MIPS: c-r4k: Avoid small flush_icache_range SMP calls
  MIPS: c-r4k: Local flush_icache_range cache op override
  MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
  ...

Pull perf updates from Ingo Molnar:
 "Mostly tooling fixes and some late tooling updates, plus two perf
  related printk message fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tests bpf: Use SyS_epoll_wait alias
  perf tests: objdump output can contain multi byte chunks
  perf record: Add --sample-cpu option
  perf hists: Introduce output_resort_cb method
  perf tools: Move config/Makefile into Makefile.config
  perf tests: Add test for bitmap_scnprintf function
  tools lib: Add bitmap_and function
  tools lib: Add bitmap_scnprintf function
  tools lib: Add bitmap_alloc function
  tools lib traceevent: Ignore generated library files
  perf tools: Fix build failure on perl script context
  perf/core: Change log level for duration warning to KERN_INFO
  perf annotate: Plug filename string leak
  perf annotate: Introduce strerror for handling symbol__disassemble() errors
  perf annotate: Rename symbol__annotate() to symbol__disassemble()
  perf/x86: Modify error message in virtualized environment
  perf target: str_error_r() always returns the buffer it receives
  perf annotate: Use pipe + fork instead of popen
  perf evsel: Introduce constructor for cycles event

Pull x86 fixes from Ingo Molnar:
 "Two fixes and a cleanup-fix, to the syscall entry code and to ptrace"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/syscalls/64: Add compat_sys_keyctl for 32-bit userspace
  x86/ptrace: Stop setting TS_COMPAT in ptrace code
  x86/vdso: Error out if the vDSO isn't a valid DSO

Pull arch/sh updates from Rich Felker:
 "These changes improve device tree support (including builtin DTB), add
  support for the J-Core J2 processor, an open source synthesizable
  reimplementation of the SH-2 ISA, resolve a longstanding sigcontext
  ABI mismatch issue, and fix various bugs including nommu-specific
  issues and minor regressions introduced in 4.6.

  The J-Core arch support is included here but to be usable it needs
  drivers that are waiting on approval/inclusion from their subsystem
  maintainers"

* tag 'sh-for-4.8' of git://git.libc.org/linux-sh: (23 commits)
  sh: add device tree source for J2 FPGA on Mimas v2 board
  sh: add defconfig for J-Core J2
  sh: use common clock framework with device tree boards
  sh: system call wire up
  sh: Delete unnecessary checks before the function call "mempool_destroy"
  sh: do not perform IPI-based cache flush except on boards that need it
  sh: add SMP support for J2
  sh: SMP support for SH2 entry.S
  sh: add working futex atomic ops on userspace addresses for smp
  sh: add J2 atomics using the cas.l instruction
  sh: add AT_HWCAP flag for J-Core cas.l instruction
  sh: add support for J-Core J2 processor
  sh: fix build regression with CONFIG_OF && !CONFIG_OF_FLATTREE
  sh: allow clocksource drivers to register sched_clock backends
  sh: make heartbeat driver explicitly non-modular
  sh: make board-secureedge5410 explicitly non-modular
  sh: make mm/asids-debugfs explicitly non-modular
  sh: make time.c explicitly non-modular
  sh: fix futex/robust_list on nommu models
  sh: disable aliased page logic on NOMMU models
  ...

Pull arm64 fixes from Will Deacon:

 - fix HugeTLB leak due to CoW and PTE_RDONLY mismatch

 - avoid accessing unmapped FDT fields when checking validity

 - correctly account for vDSO AUX entry in ARCH_DLINFO

 - fix kallsyms with absolute expressions in linker script

 - kill unnecessary symbol-based relocs in vmlinux

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Fix copy-on-write referencing in HugeTLB
  arm64: mm: avoid fdt_check_header() before the FDT is fully mapped
  arm64: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO
  arm64: relocatable: suppress R_AARCH64_ABS64 relocations in vmlinux
  arm64: vmlinux.lds: make __rela_offset and __dynsym_offset ABSOLUTE

Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "This set of changes improve some aspects of the atomic API as well as
  make use of this new API in the regulator framework to allow properly
  dealing with critical regulators controlled by a PWM.

  Aside from that there's a bunch of updates and cleanups for existing
  drivers, as well as the addition of new drivers for the Broadcom
  iProc, STMPE and ChromeOS EC controllers"

* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
  regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
  regulator: pwm: Support extra continuous mode cases
  pwm: Add ChromeOS EC PWM driver
  dt-bindings: pwm: Add binding for ChromeOS EC PWM
  mfd: cros_ec: Add EC_PWM function definitions
  mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
  pwm: atmel: Use of_device_get_match_data()
  pwm: atmel: Fix checkpatch warnings
  pwm: atmel: Fix disabling of PWM channels
  dt-bindings: pwm: Add R-Car H3 device tree bindings
  pwm: rcar: Use ARCH_RENESAS
  pwm: tegra: Add support for Tegra186
  dt-bindings: pwm: tegra: Add compatible string for Tegra186
  pwm: tegra: Avoid overflow when calculating duty cycle
  pwm: tegra: Allow 100 % duty cycle
  pwm: tegra: Add support for reset control
  pwm: tegra: Rename mmio_base to regs
  pwm: tegra: Remove useless padding
  pwm: tegra: Drop NUM_PWM macro
  pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
  ...

Pull NTB updates from Jon Mason:
 "NTB bug fixes for the ntb_tool and ntb_perf, and improvements to the
  ntb_perf and ntb_pingpong for increased debugability.

  Also, modification to the ntb_transport layer to increase/decrease
  the number of transport entries depending on the ring size"

* tag 'ntb-4.8' of git://github.com/jonmason/ntb:
  NTB: ntb_hw_intel: use local variable pdev
  NTB: ntb_hw_intel: show BAR size in debugfs info
  ntb_test: Add a selftest script for the NTB subsystem
  ntb_perf: clear link_is_up flag when the link goes down.
  ntb_pingpong: Add a debugfs file to get the ping count
  ntb_tool: Add link status and files to debugfs
  ntb_tool: Postpone memory window initialization for the user
  ntb_perf: Wait for link before running test
  ntb_perf: Return results by reading the run file
  ntb_perf: Improve thread handling to increase robustness
  ntb_perf: Schedule based on time not on performance
  ntb_transport: Check the number of spads the hardware supports
  ntb_tool: Add memory window debug support
  ntb_perf: Allow limiting the size of the memory windows
  NTB: allocate number transport entries depending on size of ring size
  ntb_tool: BUG: Ensure the buffer size is large enough to return all spads
  ntb_tool: Fix infinite loop bug when writing spad/peer_spad file

Pull pstore fixes from Kees Cook:
 "Fixes for pstore ramoops driver to catch bad kfree() and to use better
  DT bindings"

* tag 'pstore-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  ramoops: use persistent_ram_free() instead of kfree() for freeing prz
  ramoops: use DT reserved-memory bindings