- 14 May, 2012 12 commits
-
-
Bjørn Mork authored
Keep the usb-serial support for dynamic IDs in sync with the usb support. This enables readout of dynamic device IDs for usb-serial drivers. Common code is exported from the usb core system and reused by the usb-serial bus driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bjørn Mork authored
This enables the current list of dynamic IDs to be read out through either new_id or remove_id. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andrzej Pietrasiewicz authored
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
This reverts commit f397d7c4. This series isn't quite ready for 3.5 just yet, so revert it and give the author more time to get it correct. Cc: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
This reverts commit bebc56d5. The call here is fragile and not well thought out, so revert it, it's not fully baked yet and I don't want this to go into 3.5. Cc: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shinya Kuribayashi authored
Basically, ->vbus_session() calls should be served when VBUS session starts and ends (it's not whenever transciever drivers detect VBUS _changes_). Otherwise, if UDC gadget drivers don't want for some reason ->vbus_session() calls with the same "is_active" value, either OTG or UDC drivers need to have some protection handlings. Also, on platforms using this 'gpio_vbus' driver, the driver is only allowed to check whether VBUS is applied. There is no kernel-standard way prepared for UDC gadget drivers to do that. With this in mind, gpio_vbus should try to prevent unnecessary consecutive vbus_session calls being served with the same "in_active" value. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shinya Kuribayashi authored
Note that regulator_put() doesn't care about whether ->vbus_draw is valid or not. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shinya Kuribayashi authored
In commit c2344f13 (USB: gpio_vbus: add delayed vbus_session calls, 2009-01-24), usb_gadget_vbus_connect() and ...disconnect() were extracted from the interrupt handler, so to allow vbus_session handlers to deal with msleep() calls. This patch takes the approach one step further. USB2.0 specification (7.1.7.3 Connect and Disconnect Signaling) says that the USB system software (shall) provide a debounce interval with a minimum duration of 100 ms, which ensures that the electrical and mechanical connection is stable before software attempts to reset the attached device. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shinya Kuribayashi authored
'dev_id' has to be the same with the one passed to request_irq(). Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Herrmann authored
If no default value is specified, then 'n' is used so the default value used here is not needed. Furthermore, we should never change default values depending on EXPERT mode. EXPERT mode should only make options visible, not change them. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jarkko Nikula authored
Currently usb_put_transceiver calls put_device so this is a no-op but it is better to keep API usage consistent as ohci->transceiver is allocated with usb_get_transceiver. While at there remove one extra ohci->transceiver test as the code block has already tested it. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jarkko Nikula authored
Currently usb_put_transceiver calls put_device so this is a no-op but it is better to keep API usage consistent as ehci->transceiver is allocated with usb_get_transceiver. While at there remove one extra ehci->transceiver test as the code block has already tested it. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 12 May, 2012 8 commits
-
-
Lan Tianyu authored
Move child's pointer to the struct usb_hub_port since the child device is directly associated with the port. Provide usb_get_hub_child_device() to get child's pointer. Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lan Tianyu authored
Add struct usb_hub_port pointer port_data in the struct usb_hub and allocate struct usb_hub_port perspectively for each ports to store private data. Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Matthew Garrett authored
ACPI offers two methods that allow us to infer whether or not a USB port is removable. The _PLD method gives us information on whether the port is "user visible" or not. If that's not present then we can fall back to the _UPC method which tells us whether or not a port is connectable. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Matthew Garrett authored
Built-in USB devices will typically have a representation in the system ACPI tables. Add support for binding the two together so the USB code can make use of the associated methods. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Matthew Garrett authored
Add a simple helper function to allow drivers to obtain the physical device location data. Acked-by: Len Brown <len.brown@intel.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Matthew Garrett authored
It's unreasonable to have CONFIG_ACPI for these in drivers, so add some stub functions. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Now that the ChipIdea driver and related platform code has its own location in the kernel and more contributions from the interested parties are anticipated, add a new maintainer for it. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
We have the chipidea driver now that supports both langwell and penwell, so there is no need for this one any more. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 11 May, 2012 20 commits
-
-
Alexander Shishkin authored
It was used as a shorthand for gadget's device in request mapping/unmapping code, but now it's not used any more. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
We're one of the remaining drivers to map/unmap requests by hand. Switch to using generic gadget routines for that instead. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Some implementations need this limitation to work correctly. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
This adds EHCI host support to the chipidea driver. We want it to be part of the hdrc driver and not a standalone (sub-)driver module, as the structure of ehci-hcd.c suggests, so for chipidea controller we hack it to not provide platform-related code, but only the ehci hcd. The ehci-platform driver won't work for us here too, because the controller uses the same registers for both device and host mode and also otg-related bits, so it's not really possible to put ehci registers into a separate resource. This is not a pretty solution, but the alternative is exporting symbols from the chipidea driver to a ehci-chipidea driver and doing all the module refcounting. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Some of the bits of USBMODE register are defined in <usb/ehci_def.h>, use them instead of having our own definitions. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
These definitions are unused, and the same registers are also defined in <linux/usb/msm_hsusb_hw.h>. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Currently, gadget can't be NULL in _gadget_stop_activity(). Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Grzeschik authored
Move spin_lock under the done label, so the lock will also be pulled in the error paths. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> [rebased on top of the patchset] Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Get rid of trailing comments in the structure definitions in favor of kernel-doc. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
The old implementation used global hw_bank, the new implementation uses udc-local hw_bank. This field seems to be a leftover from previous coding experiments. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Add some generic code for roles and implement simple role switching based on ID pin state and/or a sysfs file. At this, we also rename the device to ci_hdrc, which is what it is. The "manual" switch is made into a sysfs file and not debugfs, because it might be useful even in non-debug context. For some boards, like sheevaplug, it seems to be the only way to switch roles without modifying the hardware, since the ID pin is always grounded. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Split the driver into the following parts: * core -- resources, register access, capabilities, etc; * udc -- device controller functionality; * debug -- logging events. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Since chipidea is a dual role controller, it makes sense to move it to its own directory, where we can also have host, otg and platform code related to this controller. It also makes sense to break out the driver into several compilation units like udc, host, debugging code, etc. Firstly, let's move the udc and platform code to drivers/usb/chipidea. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Report basic information about capabilities and register addresses on probe. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Newer versions of the chipidea controller support the "advance" setting of usb address, which means instead of setting it immediately, deferring it till the status completion. Unfortunately, older versions of the controller don't have this feature, so in order to support those too, we simply don't use it. It's about 4 lines of extra code, and isn't in any way critical to performance. While at it, change the return value of the hw_usb_set_address() to void, since it can't fail in any measurable way. With this patch, ci13xxx_udc driver works with the chipidea controller in kirkwood (feroceon SoC), as found in, for example, sheevaplug. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
The regmap field is an array of register pointers, not the other way around. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
There is no point in having tracing output in the kernel these days. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Shishkin authored
Don't try to initialize devices that don't have driver_data assigned to their pci ids. Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bjørn Mork authored
Prevents dereferencing an invalid struct usb_interface pointer. Always delete entry from device list whether or not the rest of the device state cleanup is postponed. The device list uses desc->intf as key, and wdm_open will dereference this key while searching for a matching device. A device should not appear in the list unless probe() has succeeded and disconnect() has not finished. Cc: Oliver Neukum <oliver@neukum.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bjørn Mork authored
We cannot dereference a removed USB interface for dev_printk. Use pr_debug instead where necessary. Flush errors are expected if device is unplugged and are therefore best ingored at this point. Move the kill_urbs() call in wdm_release with dev_dbg() for the non disconnect, as we know it has already been called if WDM_DISCONNECTING is set. This does not actually fix anything, but keeps the code more consistent. Cc: Oliver Neukum <oliver@neukum.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-