- 03 Mar, 2015 4 commits
-
-
Alexander Aring authored
I had this variable because I thought it would be protected by disable/enable irq but this is not true. It's protected by stop/wake netdev queue which is called by ieee802154_xmit_complete. Signed-off-by:
Alexander Aring <alex.aring@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch introduce a transmit retry handling into at86rf230 transmit path. Current behaviour is to wait the normal receive time if we want to go into STATE_TX_ON when the transceiver is in STATE_BUSY_RX_AACK which indicates that a frame is currently receiving. A non force state change will not interrupt the the receiving state. The current behaviour is that after the normal receive time we will start a force change into STATE_TX_ON. With this patch we do seven retries to go into STATE_TX_ON without forcing. After we hit the AT86RF2XX_MAX_TX_RETRIES we will start the force state change. This is a polling like method to go into STATE_TX_ON in times of maximum receiving time. Signed-off-by:
-
Kim, Ben Young Tae authored
This patch supports ROME Bluetooth family from Qualcomm Atheros, e.g. QCA61x4 or QCA6574. New chipset have similar firmware downloading sequences to previous chipset from Atheros, however, it doesn't support vid/pid switching after downloading the patch so that firmware needs to be handled by btusb module directly. ROME chipset can be differentiated from previous version by reading ROM version. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 16 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e300 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 8 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e360 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by:
-
Kim, Ben Young Tae authored
Some of chipset does not allow to send a patch or config files through HCI VS channel at early stage as well as they don't support to send USB patch files to other channel except USB bulk path. New callback added is for initialization of BT controller through USB Signed-off-by:
-
- 02 Mar, 2015 18 commits
-
-
Daniel Borkmann authored
Both sk_attach_filter() and sk_attach_bpf() are setting up sk_filter, charging skmem and attaching it to the socket after we got the eBPF prog up and ready. Lets refactor that into a common helper. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2015-03-02 Here's the first bluetooth-next pull request targeting the 4.1 kernel: - ieee802154/6lowpan cleanups - SCO routing to host interface support for the btmrvl driver - AMP code cleanups - Fixes to AMP HCI init sequence - Refactoring of the HCI callback mechanism - Added shutdown routine for Intel controllers in the btusb driver - New config option to enable/disable Bluetooth debugfs information - Fix for early data reception on L2CAP fixed channels Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by:
-
David S. Miller authored
Ying Xue says: ==================== net: Remove iocb argument from sendmsg and recvmsg Currently there is only one user - TIPC whose sendmsg() instances using iocb argument. Meanwhile, there is no user using iocb argument in its recvmsg() instance. Therefore, if we eliminate the werid usage of iobc argument from TIPC, the iocb argument can be removed from all sendmsg() and recvmsg() instances of the whole networking stack. Reference: https://patchwork.ozlabs.org/patch/433960/ Changes: v2: * Fix compile errors of DCCP module pointed by David ==================== Signed-off-by:
-
Ying Xue authored
After TIPC doesn't depend on iocb argument in its internal implementations of sendmsg() and recvmsg() hooks defined in proto structure, no any user is using iocb argument in them at all now. Then we can drop the redundant iocb argument completely from kinds of implementations of both sendmsg() and recvmsg() in the entire networking stack. Cc: Christoph Hellwig <hch@lst.de> Suggested-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Ying Xue authored
Currently the iocb argument is used to idenfiy whether or not socket lock is hold before tipc_sendmsg()/tipc_send_stream() is called. But this usage prevents iocb argument from being dropped through sendmsg() at socket common layer. Therefore, in the commit we introduce two new functions called __tipc_sendmsg() and __tipc_send_stream(). When they are invoked, it assumes that their callers have taken socket lock, thereby avoiding the weird usage of iocb argument. Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Reviewed-by:
Erik Hugne <erik.hugne@ericsson.com> Reviewed-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
David S. Miller authored
Eyal Birger says: ==================== net: move skb->dropcount to skb->cb[] Commit 97775007 ("af_packet: add interframe drop cmsg (v6)") unionized skb->mark and skb->dropcount in order to allow recording of the socket drop count while maintaining struct sk_buff size. skb->dropcount was introduced since there was no available room in skb->cb[] in packet sockets. However, its introduction led to the inability to export skb->mark to userspace. It was considered to alias skb->priority instead of skb->mark. However, that would lead to the inabilty to export skb->priority to userspace if desired. Such change may also lead to hard-to-find issues as skb->priority is assumed to be alias free, and, as noted by Shmulik Ladkani, is not 'naturally orthogonal' with other skb fields. This patch series follows the suggestions made by Eric Dumazet moving the dropcount metric to skb->cb[], eliminating this problem at the expense of 4 bytes less in skb->cb[] for protocol families using it. The patch series include compactization of bluetooth and packet use of skb->cb[] as well as the infrastructure for placing dropcount in skb->cb[]. ==================== Signed-off-by:
-
Eyal Birger authored
Commit 97775007 ("af_packet: add interframe drop cmsg (v6)") unionized skb->mark and skb->dropcount in order to allow recording of the socket drop count while maintaining struct sk_buff size. skb->dropcount was introduced since there was no available room in skb->cb[] in packet sockets. However, its introduction led to the inability to export skb->mark, or any other aliased field to userspace if so desired. Moving the dropcount metric to skb->cb[] eliminates this problem at the expense of 4 bytes less in skb->cb[] for protocol families using it. Signed-off-by:
Eyal Birger <eyal.birger@gmail.com> Signed-off-by:
-
Eyal Birger authored
As part of an effort to move skb->dropcount to skb->cb[], use a common function in order to set dropcount in struct sk_buff. Signed-off-by:
-
Eyal Birger authored
As part of an effort to move skb->dropcount to skb->cb[] use a common macro in protocol families using skb->cb[] for ancillary data to validate available room in skb->cb[]. Signed-off-by:
-
Eyal Birger authored
As part of an effort to move skb->dropcount to skb->cb[], 4 bytes of additional room are needed in skb->cb[] in packet sockets. Store the skb original length in the first two fields of sockaddr_ll (sll_family and sll_protocol) as they can be derived from the skb when needed. Signed-off-by:
-
Eyal Birger authored
Commit 3b885787 ("net: Generalize socket rx gap / receive queue overflow cmsg") allowed receiving packet dropcount information as a socket level option. RXRPC sockets recvmsg function was changed to support this by calling sock_recv_ts_and_drops() instead of sock_recv_timestamp(). However, protocol families wishing to receive dropcount should call sock_queue_rcv_skb() or set the dropcount specifically (as done in packet_rcv()). This was not done for rxrpc and thus this feature never worked on these sockets. Formalizing this by not calling sock_recv_ts_and_drops() in rxrpc as part of an effort to move skb->dropcount into skb->cb[] Signed-off-by:
-
Eyal Birger authored
Convert boolean fields incoming and req_start to bit fields and move force_active in order save space in bt_skb_cb in an effort to use a portion of skb->cb[] for storing skb->dropcount. Signed-off-by:
-
Eyal Birger authored
struct hci_req_ctrl is never used outside of struct bt_skb_cb; Inlining it frees 8 bytes on a 64 bit system in skb->cb[] allowing the addition of more ancillary data. Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by:
-
Simon Farnsworth authored
When a PADT frame is received, the socket may not be in a good state to close down the PPP interface. The current implementation handles this by simply blocking all further PPP traffic, and hoping that the lack of traffic will trigger the user to investigate. Use schedule_work to get to a process context from which we clear down the PPP interface, in a fashion analogous to hangup on a TTY-based PPP interface. This causes pppd to disconnect immediately, and allows tools to take immediate corrective action. Note that pppd's rp_pppoe.so plugin has code in it to disable the session when it disconnects; however, as a consequence of this patch, the session is already disabled before rp_pppoe.so is asked to disable the session. The result is a harmless error message: Failed to disconnect PPPoE socket: 114 Operation already in progress This message is safe to ignore, as long as the error is 114 Operation already in progress; in that specific case, it means that the PPPoE session has already been disabled before pppd tried to disable it. Signed-off-by:
Simon Farnsworth <simon@farnz.org.uk> Tested-by:
Dan Williams <dcbw@redhat.com> Tested-by:
Christoph Schulz <develop@kristov.de> Signed-off-by:
-
Ivan Vecera authored
The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag stripping when the card cannot disable it. The driver should remove NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed for the ethtool. Cc: Sony Chacko <sony.chacko@qlogic.com> Cc: Dept-HSGLinuxNICDev@qlogic.com Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Arun Chandran authored
Add *_SIZE macros for the bits ENDIA_DESC and ENDIA_PKT Signed-off-by:
Arun Chandran <achandran@mvista.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Arun Chandran authored
Program management descriptor's access mode according to the dynamically detected CPU endianness. Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
-
Shrikrishna Khare authored
Allows for packet parsing to be done by the fast path. This performance optimization already exists for IPv4. Add similar logic for IPv6. Signed-off-by:
Amitabha Banerjee <banerjeea@vmware.com> Signed-off-by:
Shrikrishna Khare <skhare@vmware.com> Signed-off-by:
-
- 01 Mar, 2015 13 commits
-
-
David S. Miller authored
Daniel Borkmann says: ==================== eBPF support for cls_bpf This is the non-RFC version of my patchset posted before netdev01 [1] conference. It contains a couple of eBPF cleanups and preparation patches to get eBPF support into cls_bpf. The last patch adds the actual support. I'll post the iproute2 parts after the kernel bits are merged, an initial preview link to the code is mentioned in the last patch. Patch 4 and 5 were originally one patch, but I've split them into two parts upon request as patch 4 only is also needed for Alexei's tracing patches that go via tip tree. Tested with tc and all in-kernel available BPF test suites. I have configured and built LLVM with --enable-experimental-targets=BPF but as Alexei put it, the plan is to get rid of the experimental status in future [2]. Thanks a lot! v1 -> v2: - Removed arch patches from this series - x86 is already queued in tip tree, under x86/mm - arm64 just reposted directly to arm folks - Rest is unchanged [1] http://thread.gmane.org/gmane.linux.network/350191 [2] http://article.gmane.org/gmane.linux.kernel/1874969 ==================== Signed-off-by:
-
Daniel Borkmann authored
This work extends the "classic" BPF programmable tc classifier by extending its scope also to native eBPF code! This allows for user space to implement own custom, 'safe' C like classifiers (or whatever other frontend language LLVM et al may provide in future), that can then be compiled with the LLVM eBPF backend to an eBPF elf file. The result of this can be loaded into the kernel via iproute2's tc. In the kernel, they can be JITed on major archs and thus run in native performance. Simple, minimal toy example to demonstrate the workflow: #include <linux/ip.h> #include <linux/if_ether.h> #include <linux/bpf.h> #include "tc_bpf_api.h" __section("classify") int cls_main(struct sk_buff *skb) { return (0x800 << 16) | load_byte(skb, ETH_HLEN + __builtin_offsetof(struct iphdr, tos)); } char __license[] __section("license") = "GPL"; The classifier can then be compiled into eBPF opcodes and loaded via tc, for example: clang -O2 -emit-llvm -c cls.c -o - | llc -march=bpf -filetype=obj -o cls.o tc filter add dev em1 parent 1: bpf cls.o [...] As it has been demonstrated, the scope can even reach up to a fully fledged flow dissector (similarly as in samples/bpf/sockex2_kern.c). For tc, maps are allowed to be used, but from kernel context only, in other words, eBPF code can keep state across filter invocations. In future, we perhaps may reattach from a different application to those maps e.g., to read out collected statistics/state. Similarly as in socket filters, we may extend functionality for eBPF classifiers over time depending on the use cases. For that purpose, cls_bpf programs are using BPF_PROG_TYPE_SCHED_CLS program type, so we can allow additional functions/accessors (e.g. an ABI compatible offset translation to skb fields/metadata). For an initial cls_bpf support, we allow the same set of helper functions as eBPF socket filters, but we could diverge at some point in time w/o problem. I was wondering whether cls_bpf and act_bpf could share C programs, I can imagine that at some point, we introduce i) further common handlers for both (or even beyond their scope), and/or if truly needed ii) some restricted function space for each of them. Both can be abstracted easily through struct bpf_verifier_ops in future. The context of cls_bpf versus act_bpf is slightly different though: a cls_bpf program will return a specific classid whereas act_bpf a drop/non-drop return code, latter may also in future mangle skbs. That said, we can surely have a "classify" and "action" section in a single object file, or considered mentioned constraint add a possibility of a shared section. The workflow for getting native eBPF running from tc [1] is as follows: for f_bpf, I've added a slightly modified ELF parser code from Alexei's kernel sample, which reads out the LLVM compiled object, sets up maps (and dynamically fixes up map fds) if any, and loads the eBPF instructions all centrally through the bpf syscall. The resulting fd from the loaded program itself is being passed down to cls_bpf, which looks up struct bpf_prog from the fd store, and holds reference, so that it stays available also after tc program lifetime. On tc filter destruction, it will then drop its reference. Moreover, I've also added the optional possibility to annotate an eBPF filter with a name (e.g. path to object file, or something else if preferred) so that when tc dumps currently installed filters, some more context can be given to an admin for a given instance (as opposed to just the file descriptor number). Last but not least, bpf_prog_get() and bpf_prog_put() needed to be exported, so that eBPF can be used from cls_bpf built as a module. Thanks to 60a3b225 ("net: bpf: make eBPF interpreter images read-only") I think this is of no concern since anything wanting to alter eBPF opcode after verification stage would crash the kernel. [1] http://git.breakpoint.cc/cgit/dborkman/iproute2.git/log/?h=ebpfSigned-off-by:Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
-
Daniel Borkmann authored
is_gpl_compatible and prog_type should be moved directly into bpf_prog as they stay immutable during bpf_prog's lifetime, are core attributes and they can be locked as read-only later on via bpf_prog_select_runtime(). With a bit of rearranging, this also allows us to shrink bpf_prog_aux to exactly 1 cacheline. Signed-off-by:
-
Daniel Borkmann authored
As discussed recently and at netconf/netdev01, we want to prevent making bpf_verifier_ops registration available for modules, but have them at a controlled place inside the kernel instead. The reason for this is, that out-of-tree modules can go crazy and define and register any verfifier ops they want, doing all sorts of crap, even bypassing available GPLed eBPF helper functions. We don't want to offer such a shiny playground, of course, but keep strict control to ourselves inside the core kernel. This also encourages us to design eBPF user helpers carefully and generically, so they can be shared among various subsystems using eBPF. For the eBPF traffic classifier (cls_bpf), it's a good start to share the same helper facilities as we currently do in eBPF for socket filters. That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus one day if there's a good reason to diverge the set of helper functions from the set available to socket filters, we keep ABI compatibility. In future, we could place all bpf_prog_type_list at a central place, perhaps. Signed-off-by:
-
Daniel Borkmann authored
This gets rid of CONFIG_BPF_SYSCALL ifdefs in the socket filter code, now that the BPF internal header can deal with it. While going over it, I also changed eBPF related functions to a sk_filter prefix to be more consistent with the rest of the file. Signed-off-by:
-
Daniel Borkmann authored
Socket filter code and other subsystems with upcoming eBPF support should not need to deal with the fact that we have CONFIG_BPF_SYSCALL defined or not. Having the bpf syscall as a config option is a nice thing and I'd expect it to stay that way for expert users (I presume one day the default setting of it might change, though), but code making use of it should not care if it's actually enabled or not. Instead, hide this via header files and let the rest deal with it. Signed-off-by:
-
Daniel Borkmann authored
We need to export BPF_PSEUDO_MAP_FD to user space, as it's used in the ELF BPF loader where instructions are being loaded that need map fixups. An initial stage loads all maps into the kernel, and later on replaces related instructions in the eBPF blob with BPF_PSEUDO_MAP_FD as source register and the actual fd as immediate value. The kernel verifier recognizes this keyword and replaces the map fd with a real pointer internally. Signed-off-by:
-
Daniel Borkmann authored
We can move bpf_map_ops and bpf_verifier_ops and other structs into ro section, bpf_map_type_list and bpf_prog_type_list into read mostly. Signed-off-by:
-
Daniel Borkmann authored
Now that we have BPF_PROG_TYPE_SOCKET_FILTER up and running, we can remove the test stubs which were added to get the verifier suite up. We can just let the test cases probe under socket filter type instead. In the fill/spill test case, we cannot (yet) access fields from the context (skb), but we may adapt that test case in future. Signed-off-by:
-
David S. Miller authored
Ursula Braun says: ==================== s390: network patches for net-next here are some s390 related patches for net-next ==================== Signed-off-by: -
Ursula Braun authored
remove Frank Blaschka as S390 NETWORK DRIVERS maintainer Acked-by:
Frank Blaschka <blaschka@linux.vnet.ibm.com> Signed-off-by:
Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by:
-
Stefan Raspl authored
This patch adjusts two instances where we were using the (too big) struct qeth_ipacmd_setadpparms size instead of the commands' actual size. This didn't do any harm, but wasted a few bytes. Signed-off-by:
Stefan Raspl <raspl@linux.vnet.ibm.com> Signed-off-by:
-
Ursula Braun authored
claw devices are outdated and no longer supported. This patch removes the claw driver. Signed-off-by:
-
- 28 Feb, 2015 5 commits
-
-
Eric Dumazet authored
tcp_fastopen_create_child() is static and should not be exported. tcp4_gso_segment() and tcp6_gso_segment() should be static. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Andrew Schwartzmeyer authored
This adds support for reporting the actual and maximum combined channels count of the hv_netvsc driver via 'ethtool --show-channels'. This required adding 'max_chn' to 'struct netvsc_device', and assigning it 'rsscap.num_recv_que' in 'rndis_filter_device_add'. Now we can access the combined maximum channel count via 'struct netvsc_device' in the ethtool callback. Signed-off-by:
Andrew Schwartzmeyer <andrew@schwartzmeyer.com> Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== tcp: tso improvements This patch serie reworks tcp_tso_should_defer() a bit to get less bursts, and better ECN behavior. We also removed tso_deferred field in tcp socket. ==================== Signed-off-by: -
Eric Dumazet authored
Another TCP issue is triggered by ECN. Under pressure, receiver gets ECN marks, and send back ACK packets with ECE TCP flag. Senders enter CA_CWR state. In this state, tcp_tso_should_defer() is short cut : if (icsk->icsk_ca_state != TCP_CA_Open) goto send_now; This means that about all ACK packets we receive are triggering a partial send, and because cwnd is kept small, we can only send a small amount of data for each incoming ACK, which in return generate more ACK packets. Allowing CA_Open and CA_CWR states to enable TSO defer in tcp_tso_should_defer() brings performance back : TSO autodefer has more chance to defer under pressure. This patch increases TSO and LRO/GRO efficiency back to normal levels, and does not impact overall ECN behavior. Signed-off-by:Yuchung Cheng <ycheng@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Eric Dumazet authored
With sysctl_tcp_min_tso_segs being 4, it is very possible that tcp_tso_should_defer() decides not sending last 2 MSS of initial window of 10 packets. This also applies if autosizing decides to send X MSS per GSO packet, and cwnd is not a multiple of X. This patch implements an heuristic based on age of first skb in write queue : If it was sent very recently (less than half srtt), we can predict that no ACK packet will come in less than half rtt, so deferring might cause an under utilization of our window. This is visible on initial send (IW10) on web servers, but more generally on some RPC, as the last part of the message might need an extra RTT to get delivered. Tested: Ran following packetdrill test // A simple server-side test that sends exactly an initial window (IW10) // worth of packets. `sysctl -e -q net.ipv4.tcp_min_tso_segs=4` 0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0 +0 bind(3, ..., ...) = 0 +0 listen(3, 1) = 0 +.1 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7> +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6> +.1 < . 1:1(0) ack 1 win 257 +0 accept(3, ..., ...) = 4 +0 write(4, ..., 14600) = 14600 +0 > . 1:5841(5840) ack 1 win 457 +0 > . 5841:11681(5840) ack 1 win 457 // Following packet should be sent right now. +0 > P. 11681:14601(2920) ack 1 win 457 +.1 < . 1:1(0) ack 14601 win 257 +0 close(4) = 0 +0 > F. 14601:14601(0) ack 1 +.1 < F. 1:1(0) ack 14602 win 257 +0 > . 14602:14602(0) ack 2 Signed-off-by:
-
