Currently, watchdog subsystem require the misc subsystem to
register a watchdog. This may not be the case in case of an
early registration of a watchdog, which can be required when
the watchdog cannot be disabled.

This patch introduces a deferral mechanism to remove this requirement.
Signed-off-by: Jean-Baptiste Theou <jtheou@adeneo-embedded.us>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This patch removes the static watchdog device for a new max63xx_wdt data
structure, and constifies the max63xx_timeout data.

The new structure contains pointers to pin access routines, which
abstracts mmap-specific code. This will ease future accesses like GPIO.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

If watchdog_register_device() fails we should disable the previously
acquired wdev->clk clock on error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

WDIOC_SETOPTIONS makes it possible to disable and re-enable the
watchdog timer while the hpwdt driver is loaded.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The omap_wdt kernel driver also understands the nowayout module
parameter. This updates the watchdog-parameters.txt to reflect this fact.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The omap watchdog hardware is able to read the watchdog timer counter
register. This implements this functionality in the omap_wdt driver, so
one is can read the time until the watchdog will trigger the reset in
seconds using WDIOC_GETTIMELEFT.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add watchdog driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

If on watchdog device registration a parent device is not set, then
the registered watchdog is considered to be a virtual device:

  /sys/devices/virtual/watchdog/watchdog0
  /sys/devices/virtual/watchdog/watchdog1

Setting a correct reference to a platform device allows to
distinguish multiple instances of iMX2+ hardware watchdogs:

  /sys/devices/soc0/soc/2000000.aips-bus/20bc000.wdog/watchdog/watchdog0
  /sys/devices/soc0/soc/2000000.aips-bus/20c0000.wdog/watchdog/watchdog1
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

In a21_wdt_remove() we do a watchdog_unregister_device() on struct
a21_wdt_drv->wdt but never assign it.

Also move the dev_set_drvdata() call in front of the watchdog_register_device()
call, so it doesn't look like an error.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

If you've got code that does this in a tight loop
  1. Open watchdog
  2. Send 'expect close'
  3. Close watchdog
...you'll eventually trigger a watchdog reset.  You can reproduce this
by using daisydog (1) and running:
  while true; do daisydog -c > /dev/null; done

The problem is that each time you write to the watchdog for 'expect
close' it moves the timer .5 seconds out.  The timer thus never fires
and never pats the watchdog for you.

1: http://git.chromium.org/gitweb/?p=chromiumos/third_party/daisydog.gitSigned-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Right now the dw_wdt uses a spinlock to protect dw_wdt_open().  The
problem is that while holding the spinlock we call:
-> dw_wdt_set_top()
   -> dw_wdt_top_in_seconds()
      -> clk_get_rate()
         -> clk_prepare_lock()
            -> mutex_lock()

Locking a mutex while holding a spinlock is not allowed and leads to
warnings like "BUG: spinlock wrong CPU on CPU#1", among other
problems.

There's no reason to use a spinlock.  Only dw_wdt_open() was protected
and the test_and_set_bit() at the start of that function protects us
anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Commit faad5de0 ("watchdog: imx2_wdt: convert to watchdog core api")
removes the custom ioctl function. The generic ioctl handler is not
setting the wdog->timeout to the new_timeout but handing this preset
value back to the userspace. This patch sets the new value in the
drivers set_timeout function to fix that problem.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org

Not all architectures have io memory.

Fixes:
drivers/built-in.o: In function `cdns_wdt_probe':
cadence_wdt.c:(.text+0x33b7c9): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Remove the ARM Kconfig dependency since the Maxim MAX63xx devices are
architecture independent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This watchdog hardware can be configured in terms of power-of-two
clock cycles. Therefore, the watchdog timeout configured by the user
will be rounded-up to the next possible hardware timeout.

This commit adds a comment explaining this.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Maximum timeout is currently set in clock cycles, but the watchdog
core expects it to be in seconds. Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Register a restart handler that will restart the system by writing
to the watchdog's SOFT_RESET register.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Set up the watchdog for the specified timeout before attempting to start it.
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Since the heartbeat is statically initialized to its default value,
watchdog_init_timeout() will never look in the device-tree for a
timeout-sec value.  Instead of statically initializing heartbeat,
fall back to the default timeout value if watchdog_init_timeout()
fails.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The omap watchdog has the annoying behaviour that writes to most
registers don't have any effect when the watchdog is already running.
Quoting the AM335x reference manual:

	To modify the timer counter value (the WDT_WCRR register),
	prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay
	configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or
	the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the
	watchdog timer must be disabled by using the start/stop sequence
	(the WDT_WSPR register).

Currently the timer is stopped in the .probe callback but still there
are possibilities that yield to a situation where omap_wdt_start is
entered with the timer running (e.g. when /dev/watchdog is closed
without stopping and then reopened). In such a case programming the
timeout silently fails!

To circumvent this stop the timer before reprogramming.

Assuming one of the first things the watchdog user does is setting the
timeout explicitly nothing too bad should happen because this explicit
setting works fine.

Fixes: 7768a13c ("[PATCH] OMAP: Add Watchdog driver support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Instead of using an over-long expression involving the ?: operator use
an if and instead of an else branch rely on the fact that the data
structure was allocated using devm_kzalloc. This also allows to put the
used helper variable into a more local scope.

There is no functional change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This way only a single allocation is needed (per device). Also this
simplifies the data structure used by the driver because there is no
need anymore to link from one struct to the other (by means of
watchdog_{set,get}_drvdata).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Instead of (partly) open coding watchdog_init_timeout to determine the
inital timeout use the core function that exists for exactly this
purpose.

As a side effect the "timeout-sec" device-tree property is recognized now
(though currently unused in the omap device trees).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

ti,hwmods doesn't belong into the compatible section but is a property
on it's own. Also reformat the section of required properties to match the
usual style of dt binding documents.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This commit add a driver for the watchdog functionality of the Conexant CX92755
SoC, from the Digicolor series of SoCs. Of 8 system timers provided by the
CX92755, the first one, timer A, can reset the chip when its counter reaches
zero. This driver uses this capability to provide userspace with a standard
watchdog, using the watchdog timer driver core framework. This driver also
implements a reboot handler for the reboot(2) system call.

The watchdog driver shares the timer registers with the CX92755 timer driver
(drivers/clocksource/timer-digicolor.c). The timer driver, however, uses only
timers other than A, so both drivers should coexist.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add a device tree binding documentation to the watchdog hardware block on the
Conexant CX92755 SoC. The CX92755 is from the Digicolor SoCs series. Other SoCs
in that series may share the same hardware block.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Use endian agnostic IO functions for the watchdog driver for when it
is enabled on ATSAMA5D36 devices running in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Initial submission adding support for this IP only included Watchdog and
the Real-Time Clock.  Now the third (and final) device is enabled this
trivial patch is required to update the comment in the Watchdog driver
to encompass Clocksource.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

On current ST platforms the LPC controls a number of functions including
Watchdog and Real Time Clock.  This patch provides the bindings used to
configure LPC in Watchdog mode.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

ST's Low Power Controller can currently operate in two supported modes;
Watchdog and Real Time Clock.  These defines will aid engineers to easily
identify the selected mode.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull scsi target fixes from Nicholas Bellinger:
 "Apologies for the late pull request.

  Here are the outstanding target-pending fixes for v4.1 code.

  The series contains three patches from Sagi + Co that address a few
  iser-target issues that have been uncovered during recent testing at
  Mellanox.

  Patch #1 has a v3.16+ stable tag, and #2-3 have v3.10+ stable tags"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iser-target: Fix possible use-after-free
  iser-target: release stale iser connections
  iser-target: Fix variable-length response error completion

Pull drm fixes from Dave Airlie:
 "A smattering of fixes,

  mgag200:
      don't accept modes that aren't aligned properly as hw can't do it

  i915:
      two regression fixes

  radeon:
      one query to allow userspace fixes
      one oops fixer for older hw with new options enabled"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: don't probe MST on hw we don't support it on
  drm/radeon: Add RADEON_INFO_VA_UNMAP_WORKING query
  drm/mgag200: Reject non-character-cell-aligned mode widths
  Revert "drm/i915: Don't skip request retirement if the active list is empty"
  drm/i915: Always reset vma->ggtt_view.pages cache on unbinding

Pull clk fixes from Michael Turquette:
 "Very late clk regression fixes for the ARM-based AT91 platform.

  These went unnoticed by me until recently, hence the late pull
  request"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: at91: fix h32mx prototype inclusion in pmc header
  clk: at91: trivial: typo in peripheral clock description
  clk: at91: fix PERIPHERAL_MAX_SHIFT definition
  clk: at91: pll: fix input range validity check

Pull sound fixes from Takashi Iwai:
 "Nothing looks scary, just a few usual HD-audio regression fixes and
  fixup, in addition to a minor Kconfig dependency fix for the old MIPS
  drivers"

* tag 'sound-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix unused label skip_i915
  ALSA: hda - Fix noisy outputs on Dell XPS13 (2015 model)
  ALSA: mips: let SND_SGI_O2 select SND_PCM
  ALSA: hda - Fix audio crackles on Dell Latitude E7x40
  ALSA: hda - adding a DAC/pin preference map for a HP Envy TS machine