- 18 Oct, 2018 40 commits
-
-
Mike Snitzer authored
commit beb9caac upstream. It is best to avoid any extra overhead associated with bio completion. DM core will indirectly call a DM target's .end_io if it is defined. In the case of DM linear, there is no need to do so (for every bio that completes) if CONFIG_DM_ZONED is not enabled. Avoiding an extra indirect call for every bio completion is very important for ensuring DM linear doesn't incur more overhead that further widens the performance gap between dm-linear and raw block devices. Fixes: 0be12c1c ("dm linear: add support for zoned block devices") Cc: stable@vger.kernel.org Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Damien Le Moal authored
commit 9864cd5d upstream. If dm-linear or dm-flakey are layered on top of a partition of a zoned block device, remapping of the start sector and write pointer position of the zones reported by a report zones BIO must be modified to account for the target table entry mapping (start offset within the device and entry mapping with the dm device). If the target's backing device is a partition of a whole disk, the start sector on the physical device of the partition must also be accounted for when modifying the zone information. However, dm_remap_zone_report() was not considering this last case, resulting in incorrect zone information remapping with targets using disk partitions. Fix this by calculating the target backing device start sector using the position of the completed report zones BIO and the unchanged position and size of the original report zone BIO. With this value calculated, the start sector and write pointer position of the target zones can be correctly remapped. Fixes: 10999307 ("dm: introduce dm_remap_zone_report()") Cc: stable@vger.kernel.org Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
-
Shenghui Wang authored
commit c7cd5550 upstream. Commit 7e6358d2 ("dm: fix various targets to dm_register_target after module __init resources created") inadvertently introduced this bug when it moved dm_register_target() after the call to KMEM_CACHE(). Fixes: 7e6358d2 ("dm: fix various targets to dm_register_target after module __init resources created") Cc: stable@vger.kernel.org Signed-off-by:
Shenghui Wang <shhuiw@foxmail.com> Signed-off-by:
-
Eric Farman authored
commit 24abf290 upstream. We have two nested loops to check the entries within the pfn_array_table arrays. But we mistakenly use the outer array as an index in our check, and completely ignore the indexing performed by the inner loop. Cc: stable@vger.kernel.org Signed-off-by:
Eric Farman <farman@linux.ibm.com> Message-Id: <20181002010235.42483-1-farman@linux.ibm.com> Signed-off-by:
Cornelia Huck <cohuck@redhat.com> Signed-off-by:
-
Adrian Hunter authored
commit d005efe1 upstream. With the "branches" export option, not all sample columns are exported. However the unwanted columns are not at the end of the tuple, as assumed by the code. Fix by taking the first 15 and last 3 values, instead of the first 18. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20180911114504.28516-3-adrian.hunter@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Adrian Hunter authored
commit 25e11700 upstream. Occasional export failures were found to be caused by truncating 64-bit pointers to 32-bits. Fix by explicitly setting types for all ctype arguments and results. Signed-off-by:
-
Mike Rapoport authored
commit 6685b357 upstream. The commit ca460b3c ("percpu: introduce bitmap metadata blocks") introduced bitmap metadata blocks. These metadata blocks are allocated whenever a new chunk is created, but they are never freed. Fix it. Fixes: ca460b3c ("percpu: introduce bitmap metadata blocks") Signed-off-by:
Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Signed-off-by:
Dennis Zhou <dennis@kernel.org> Signed-off-by:
-
Mikulas Patocka authored
commit 76ebebd2 upstream. On Sun Ultra 5, it happens that the dot clock is not set up properly for some videomodes. For example, if we set the videomode "r1024x768x60" in the firmware, Linux would incorrectly set a videomode with refresh rate 180Hz when booting (suprisingly, my LCD monitor can display it, although display quality is very low). The reason is this: Older mach64 cards set the divider in the register VCLK_POST_DIV. The register has four 2-bit fields (the field that is actually used is specified in the lowest two bits of the register CLOCK_CNTL). The 2 bits select divider "1, 2, 4, 8". On newer mach64 cards, there's another bit added - the top four bits of PLL_EXT_CNTL extend the divider selection, so we have possible dividers "1, 2, 4, 8, 3, 5, 6, 12". The Linux driver clears the top four bits of PLL_EXT_CNTL and never sets them, so it can work regardless if the card supports them. However, the sparc64 firmware may set these extended dividers during boot - and the mach64 driver detects incorrect dot clock in this case. This patch makes the driver read the additional divider bit from PLL_EXT_CNTL and calculate the initial refresh rate properly. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Acked-by:
David S. Miller <davem@davemloft.net> Reviewed-by:
Ville Syrjälä <syrjala@sci.fi> Signed-off-by:
-
Paul Burton authored
commit ea7e0480 upstream. When using the legacy mmap layout, for example triggered using ulimit -s unlimited, get_unmapped_area() fills memory from bottom to top starting from a fairly low address near TASK_UNMAPPED_BASE. This placement is suboptimal if the user application wishes to allocate large amounts of heap memory using the brk syscall. With the VDSO being located low in the user's virtual address space, the amount of space available for access using brk is limited much more than it was prior to the introduction of the VDSO. For example: # ulimit -s unlimited; cat /proc/self/maps 00400000-004ec000 r-xp 00000000 08:00 71436 /usr/bin/coreutils 004fc000-004fd000 rwxp 000ec000 08:00 71436 /usr/bin/coreutils 004fd000-0050f000 rwxp 00000000 00:00 0 00cc3000-00ce4000 rwxp 00000000 00:00 0 [heap] 2ab96000-2ab98000 r--p 00000000 00:00 0 [vvar] 2ab98000-2ab99000 r-xp 00000000 00:00 0 [vdso] 2ab99000-2ab9d000 rwxp 00000000 00:00 0 ... Resolve this by adjusting STACK_TOP to reserve space for the VDSO & providing an address hint to get_unmapped_area() causing it to use this space even when using the legacy mmap layout. We reserve enough space for the VDSO, plus 1MB or 256MB for 32 bit & 64 bit systems respectively within which we randomize the VDSO base address. Previously this randomization was taken care of by the mmap base address randomization performed by arch_mmap_rnd(). The 1MB & 256MB sizes are somewhat arbitrary but chosen such that we have some randomization without taking up too much of the user's virtual address space, which is often in short supply for 32 bit systems. With this the VDSO is always mapped at a high address, leaving lots of space for statically linked programs to make use of brk: # ulimit -s unlimited; cat /proc/self/maps 00400000-004ec000 r-xp 00000000 08:00 71436 /usr/bin/coreutils 004fc000-004fd000 rwxp 000ec000 08:00 71436 /usr/bin/coreutils 004fd000-0050f000 rwxp 00000000 00:00 0 00c28000-00c49000 rwxp 00000000 00:00 0 [heap] ... 7f67c000-7f69d000 rwxp 00000000 00:00 0 [stack] 7f7fc000-7f7fd000 rwxp 00000000 00:00 0 7fcf1000-7fcf3000 r--p 00000000 00:00 0 [vvar] 7fcf3000-7fcf4000 r-xp 00000000 00:00 0 [vdso] Signed-off-by:
Paul Burton <paul.burton@mips.com> Reported-by:
Huacai Chen <chenhc@lemote.com> Fixes: ebb5e78c ("MIPS: Initial implementation of a VDSO") Cc: Huacai Chen <chenhc@lemote.com> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org # v4.4+ Signed-off-by:
-
Jann Horn authored
commit 28e2c4bb upstream. 7a9cdebd ("mm: get rid of vmacache_flush_all() entirely") removed the VMACACHE_FULL_FLUSHES statistics, but didn't remove the corresponding entry in vmstat_text. This causes an out-of-bounds access in vmstat_show(). Luckily this only affects kernels with CONFIG_DEBUG_VM_VMACACHE=y, which is probably very rare. Link: http://lkml.kernel.org/r/20181001143138.95119-1-jannh@google.com Fixes: 7a9cdebd ("mm: get rid of vmacache_flush_all() entirely") Signed-off-by:
Jann Horn <jannh@google.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Acked-by:
Michal Hocko <mhocko@suse.com> Acked-by:
Roman Gushchin <guro@fb.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Kemi Wang <kemi.wang@intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Amber Lin authored
[ Upstream commit caaa4c8a ] A wrong register bit was examinated for checking SDMA status so it reports false failures. This typo only appears on gfx_v7. gfx_v8 checks the correct bit. Acked-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Amber Lin <Amber.Lin@amd.com> Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
-
Vitaly Kuznetsov authored
[ Upstream commit d1766202 ] When VMX is used with flexpriority disabled (because of no support or if disabled with module parameter) MMIO interface to lAPIC is still available in x2APIC mode while it shouldn't be (kvm-unit-tests): PASS: apic_disable: Local apic enabled in x2APIC mode PASS: apic_disable: CPUID.1H:EDX.APIC[bit 9] is set FAIL: apic_disable: *0xfee00030: 50014 The issue appears because we basically do nothing while switching to x2APIC mode when APIC access page is not used. apic_mmio_{read,write} only check if lAPIC is disabled before proceeding to actual write. When APIC access is virtualized we correctly manipulate with VMX controls in vmx_set_virtual_apic_mode() and we don't get vmexits from memory writes in x2APIC mode so there's no issue. Disabling MMIO interface seems to be easy. The question is: what do we do with these reads and writes? If we add apic_x2apic_mode() check to apic_mmio_in_range() and return -EOPNOTSUPP these reads and writes will go to userspace. When lAPIC is in kernel, Qemu uses this interface to inject MSIs only (see kvm_apic_mem_write() in hw/i386/kvm/apic.c). This somehow works with disabled lAPIC but when we're in xAPIC mode we will get a real injected MSI from every write to lAPIC. Not good. The simplest solution seems to be to just ignore writes to the region and return ~0 for all reads when we're in x2APIC mode. This is what this patch does. However, this approach is inconsistent with what currently happens when flexpriority is enabled: we allocate APIC access page and create KVM memory region so in x2APIC modes all reads and writes go to this pre-allocated page which is, btw, the same for all vCPUs. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 648e9218 ] Commit d31fd43c ("clk: x86: Do not gate clocks enabled by the firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes all unclaimed PMC clocks on Cherry Trail devices to be on all the time, resulting on the device not being able to reach S0i3 when suspended. The reason for this commit is that on some Bay Trail / Cherry Trail devices the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver has been modified to get and enable this clock (if present) the marking of the clocks as CLK_IS_CRITICAL is no longer necessary. This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail devices not being able to reach S0i3 greatly decreasing their battery drain when suspended. Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by:
Johannes Stezenbach <js@sig21.net> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit b1e3454d ] Commit d31fd43c ("clk: x86: Do not gate clocks enabled by the firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on all the time, resulting on the device not being able to reach S0i2 or S0i3 when suspended. The reason for this commit is that on some Bay Trail / Cherry Trail devices the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk" alias, so that the relevant ethernet drivers can try to (optionally) use this, without needing X86 specific code / hacks, thus fixing ethernet on these devices without breaking S0i3 support. This commit uses clkdev_hw_create() to create the alias, mirroring the code for the already existing "mclk" alias for pmc_plt_clk_3. Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by:
-
Stephen Hemminger authored
[ Upstream commit a15f2c08 ] The Hyper-V host API for PCI provides a unique "serial number" which can be used as basis for sysfs PCI slot table. This can be useful for cases where userspace wants to find the PCI device based on serial number. When an SR-IOV NIC is added, the host sends an attach message with serial number. The kernel doesn't use the serial number, but it is useful when doing the same thing in a userspace driver such as the DPDK. By having /sys/bus/pci/slots/N it provides a direct way to find the matching PCI device. There maybe some cases where serial number is not unique such as when using GPU's. But the PCI slot infrastructure will handle that. This has a side effect which may also be useful. The common udev network device naming policy uses the slot information (rather than PCI address). Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
Nicolas Ferre authored
[ Upstream commit 321cc359 ] We need this new compatibility string as we experienced different behavior for this 10/100Mbits/s macb interface on this particular SoC. Backward compatibility is preserved as we keep the alternative strings. Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Nicolas Ferre authored
[ Upstream commit eb4ed8e2 ] Create a new configuration for the sama5d3-macb new compatibility string. This configuration disables scatter-gather because we experienced lock down of the macb interface of this particular SoC under very high load. Signed-off-by:
-
Jongsung Kim authored
[ Upstream commit edf2ef72 ] Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or 128 unicast filter entries. (Table 7-8 MAC Address Registers from databook) Fix dwmac1000_validate_ucast_entries() to accept values between 1 and 32 in addition. Signed-off-by:
Jongsung Kim <neidhard.kim@lge.com> Signed-off-by:
-
Stephen Hemminger authored
[ Upstream commit 018349d7 ] When netvsc device is removed it can call reschedule in RCU context. This happens because canceling the subchannel setup work could (in theory) cause a reschedule when manipulating the timer. To reproduce, run with lockdep enabled kernel and unbind a network device from hv_netvsc (via sysfs). [ 160.682011] WARNING: suspicious RCU usage [ 160.707466] 4.19.0-rc3-uio+ #2 Not tainted [ 160.709937] ----------------------------- [ 160.712352] ./include/linux/rcupdate.h:302 Illegal context switch in RCU read-side critical section! [ 160.723691] [ 160.723691] other info that might help us debug this: [ 160.723691] [ 160.730955] [ 160.730955] rcu_scheduler_active = 2, debug_locks = 1 [ 160.762813] 5 locks held by rebind-eth.sh/1812: [ 160.766851] #0: 000000008befa37a (sb_writers#6){.+.+}, at: vfs_write+0x184/0x1b0 [ 160.773416] #1: 00000000b097f236 (&of->mutex){+.+.}, at: kernfs_fop_write+0xe2/0x1a0 [ 160.783766] #2: 0000000041ee6889 (kn->count#3){++++}, at: kernfs_fop_write+0xeb/0x1a0 [ 160.787465] #3: 0000000056d92a74 (&dev->mutex){....}, at: device_release_driver_internal+0x39/0x250 [ 160.816987] #4: 0000000030f6031e (rcu_read_lock){....}, at: netvsc_remove+0x1e/0x250 [hv_netvsc] [ 160.828629] [ 160.828629] stack backtrace: [ 160.831966] CPU: 1 PID: 1812 Comm: rebind-eth.sh Not tainted 4.19.0-rc3-uio+ #2 [ 160.832952] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012 [ 160.832952] Call Trace: [ 160.832952] dump_stack+0x85/0xcb [ 160.832952] ___might_sleep+0x1a3/0x240 [ 160.832952] __flush_work+0x57/0x2e0 [ 160.832952] ? __mutex_lock+0x83/0x990 [ 160.832952] ? __kernfs_remove+0x24f/0x2e0 [ 160.832952] ? __kernfs_remove+0x1b2/0x2e0 [ 160.832952] ? mark_held_locks+0x50/0x80 [ 160.832952] ? get_work_pool+0x90/0x90 [ 160.832952] __cancel_work_timer+0x13c/0x1e0 [ 160.832952] ? netvsc_remove+0x1e/0x250 [hv_netvsc] [ 160.832952] ? __lock_is_held+0x55/0x90 [ 160.832952] netvsc_remove+0x9a/0x250 [hv_netvsc] [ 160.832952] vmbus_remove+0x26/0x30 [ 160.832952] device_release_driver_internal+0x18a/0x250 [ 160.832952] unbind_store+0xb4/0x180 [ 160.832952] kernfs_fop_write+0x113/0x1a0 [ 160.832952] __vfs_write+0x36/0x1a0 [ 160.832952] ? rcu_read_lock_sched_held+0x6b/0x80 [ 160.832952] ? rcu_sync_lockdep_assert+0x2e/0x60 [ 160.832952] ? __sb_start_write+0x141/0x1a0 [ 160.832952] ? vfs_write+0x184/0x1b0 [ 160.832952] vfs_write+0xbe/0x1b0 [ 160.832952] ksys_write+0x55/0xc0 [ 160.832952] do_syscall_64+0x60/0x1b0 [ 160.832952] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 160.832952] RIP: 0033:0x7fe48f4c8154 Resolve this by getting RTNL earlier. This is safe because the subchannel work queue does trylock on RTNL and will detect the race. Fixes: 7b2ee50c ("hv_netvsc: common detach logic") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Yu Zhao authored
[ Upstream commit 75383f8d ] Internally, skl_init_chip() calls snd_hdac_bus_init_chip() which 1) sets bus->chip_init to prevent multiple entrances before device is stopped; 2) enables interrupt. We shouldn't use it for the purpose of resetting device only because 1) when we really want to initialize device, we won't be able to do so; 2) we are ready to handle interrupt yet, and kernel crashes when interrupt comes in. Rename azx_reset() to snd_hdac_bus_reset_link(), and use it to reset device properly. Fixes: 60767abc ("ASoC: Intel: Skylake: Reset the controller in probe") Reviewed-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Yu Zhao <yuzhao@google.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Yu Zhao authored
[ Upstream commit b61749a8 ] In snd_hdac_bus_init_chip(), we enable interrupt before snd_hdac_bus_init_cmd_io() initializing dma buffers. If irq has been acquired and irq handler uses the dma buffer, kernel may crash when interrupt comes in. Fix the problem by postponing enabling irq after dma buffer initialization. And warn once on null dma buffer pointer during the initialization. Reviewed-by:
-
Dan Carpenter authored
[ Upstream commit cbe3fd39 ] We should first do the le16_to_cpu endian conversion and then apply the FCP_CMD_LENGTH_MASK mask. Fixes: 5f35509d ("qla2xxx: Terminate exchange if corrupted") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Quinn Tran <Quinn.Tran@cavium.com> Acked-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Laura Abbott authored
[ Upstream commit 679fcae4 ] Fedora got a bug report of a crash with iSCSI: kernel BUG at include/linux/scatterlist.h:143! ... RIP: 0010:iscsit_do_crypto_hash_buf+0x154/0x180 [iscsi_target_mod] ... Call Trace: ? iscsi_target_tx_thread+0x200/0x200 [iscsi_target_mod] iscsit_get_rx_pdu+0x4cd/0xa90 [iscsi_target_mod] ? native_sched_clock+0x3e/0xa0 ? iscsi_target_tx_thread+0x200/0x200 [iscsi_target_mod] iscsi_target_rx_thread+0x81/0xf0 [iscsi_target_mod] kthread+0x120/0x140 ? kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x3a/0x50 This is a BUG_ON for using a stack buffer with a scatterlist. There are two cases that trigger this bug. Switch to using a dynamically allocated buffer for one case and do not assign a NULL buffer in another case. Signed-off-by:
Laura Abbott <labbott@redhat.com> Reviewed-by:
Mike Christie <mchristi@redhat.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 10492ee8 ] It currently only works if the parent bus uses "simple-bus". We currently try to probe children with non-existing compatible values. And we're missing .probe. I noticed this while testing devices configured to probe using ti-sysc interconnect target module driver. For that we also may want to rebind the driver, so let's remove __init and __exit. Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Hermes Zhang authored
[ Upstream commit e6a57d22 ] The percpu_rw_semaphore is not currently freed, and this leads to a crash when the stale rcu callback is invoked. DEBUG_OBJECTS detects this. ODEBUG: free active (active state 1) object type: rcu_head hint: (null) ------------[ cut here ]------------ WARNING: CPU: 1 PID: 2024 at debug_print_object+0xac/0xc8 PC is at debug_print_object+0xac/0xc8 LR is at debug_print_object+0xac/0xc8 Call trace: [<ffffff80082e2c2c>] debug_print_object+0xac/0xc8 [<ffffff80082e40b0>] debug_check_no_obj_freed+0x1e8/0x228 [<ffffff8008191254>] kfree+0x1cc/0x250 [<ffffff80083cc03c>] hci_uart_tty_close+0x54/0x108 [<ffffff800832e118>] tty_ldisc_close.isra.1+0x40/0x58 [<ffffff800832e14c>] tty_ldisc_kill+0x1c/0x40 [<ffffff800832e3dc>] tty_ldisc_release+0x94/0x170 [<ffffff8008325554>] tty_release_struct+0x1c/0x58 [<ffffff8008326400>] tty_release+0x3b0/0x490 [<ffffff80081a3fe8>] __fput+0x88/0x1d0 [<ffffff80081a418c>] ____fput+0xc/0x18 [<ffffff80080c0624>] task_work_run+0x9c/0xc0 [<ffffff80080a9e24>] do_exit+0x24c/0x8a0 [<ffffff80080aa4e0>] do_group_exit+0x38/0xa0 [<ffffff80080aa558>] __wake_up_parent+0x0/0x28 [<ffffff8008082c00>] el0_svc_naked+0x34/0x38 ---[ end trace bfe08cbd89098cdf ]--- Signed-off-by:
Hermes Zhang <chenhuiz@axis.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Kuninori Morimoto authored
[ Upstream commit 6c92d5a2 ] Current rsnd driver will fallback to PIO mode if it can't get DMA handler. But, DMA might return -EPROBE_DEFER when probe timing. This driver always fallback to PIO mode especially from commit ac6bbf0c ("iommu: Remove IOMMU_OF_DECLARE") because of this reason. The DMA driver will be probed later, but sound driver might be probed as PIO mode in such case. This patch fixup this issue. Then, -EPROBE_DEFER is not error. Thus, let's don't indicate error message in such case. And it needs to call rsnd_adg_remove() individually if probe failed, because it registers clk which should be unregister. Maybe PIO fallback feature itself is not needed, but let's keep it so far. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
[ Upstream commit 69235ccf ] ADG has buffer over flow bug if DT has more than 3 clock-frequency. This patch fixup this issue, and uses first 2 values. clock-frequency = <x y>; /* this is OK */ clock-frequency = <x y z>; /* this is NG */ Signed-off-by:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by:
-
Lei Yang authored
[ Upstream commit 4d85af10 ] add CONFIG_MEMORY_HOTREMOVE=y in config without this config, /sys/devices/system/memory/memory*/removable always return 0, I endup getting an early skip during test Signed-off-by:
Lei Yang <Lei.Yang@windriver.com> Signed-off-by:
Shuah Khan (Samsung OSG) <shuah@kernel.org> Signed-off-by:
-
Lei Yang authored
[ Upstream commit 53cf59d6 ] add config file Signed-off-by:
-
Danny Smith authored
[ Upstream commit 5ea752c6 ] Fixed range in safeload conditional to allow safeload to up to 20 bytes, without a lower limit. Signed-off-by:
Danny Smith <dannys@axis.com> Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Pierre-Louis Bossart authored
[ Upstream commit 960cdd50 ] HID made of either Wolfson/CirrusLogic PCI ID + 8804 identifier. This helps enumerate the HifiBerry Digi+ HAT boards on the Up2 platform. The scripts at https://github.com/thesofproject/acpi-scripts can be used to add the ACPI initrd overlays. Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
-
Oder Chiou authored
[ Upstream commit 6f0a2562 ] After our evaluation, we need to modify the default values to make sure the volume applied immediately. Signed-off-by:
Oder Chiou <oder_chiou@realtek.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 2ab2ddd3 ] Timer handlers do not imply rcu_read_lock(), so my recent fix triggered a LOCKDEP warning when SYNACK is retransmit. Lets add rcu_read_lock()/rcu_read_unlock() pairs around ireq->ireq_opt usages instead of guessing what is done by callers, since it is not worth the pain. Get rid of ireq_opt_deref() helper since it hides the logic without real benefit, since it is now a standard rcu_dereference(). Fixes: 1ad98e9d ("tcp/dccp: fix lockdep issue when SYN is backlogged") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 1ad98e9d ] In normal SYN processing, packets are handled without listener lock and in RCU protected ingress path. But syzkaller is known to be able to trick us and SYN packets might be processed in process context, after being queued into socket backlog. In commit 06f877d6 ("tcp/dccp: fix other lockdep splats accessing ireq_opt") I made a very stupid fix, that happened to work mostly because of the regular path being RCU protected. Really the thing protecting ireq->ireq_opt is RCU read lock, and the pseudo request refcnt is not relevant. This patch extends what I did in commit 449809a6 ("tcp/dccp: block BH for SYN processing") by adding an extra rcu_read_{lock|unlock} pair in the paths that might be taken when processing SYN from socket backlog (thus possibly in process context) Fixes: 06f877d6 ("tcp/dccp: fix other lockdep splats accessing ireq_opt") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Maciej Żenczykowski authored
[ Upstream commit 474ff260 ] So it should not fail with EPERM even though it is no longer implemented... This is a fix for: (userns)$ egrep ^Cap /proc/self/status CapInh: 0000003fffffffff CapPrm: 0000003fffffffff CapEff: 0000003fffffffff CapBnd: 0000003fffffffff CapAmb: 0000003fffffffff (userns)$ tcpdump -i usb_rndis0 tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted Warning: Kernel filter failed: Bad file descriptor tcpdump: can't remove kernel filter: Bad file descriptor With this change it returns EOPNOTSUPP instead of EPERM. See also https://github.com/the-tcpdump-group/libpcap/issues/689 Fixes: 08a00fea "net: Remove references to NETIF_F_UFO from ethtool." Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
-
Davide Caratti authored
[ Upstream commit 8c6ec361 ] bnxt offload code currently supports only 'push' and 'pop' operation: let .ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured. Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Sathya Perla <sathya.perla@broadcom.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit ff58e2df ] When FW floods the driver with control messages try to exit the cmsg processing loop every now and then to avoid soft lockups. Cmsg processing is generally very lightweight so 512 seems like a reasonable budget, which should not be exceeded under normal conditions. Fixes: 77ece8d5 ("nfp: add control vNIC datapath") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Tested-by:
Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by:
-
Mahesh Bandewar authored
[ Upstream commit 0f3b914c ] RX queue config for bonding master could be different from its slave device(s). With the commit 6a9e461f ("bonding: pass link-local packets to bonding master also."), the packet is reinjected into stack with skb->dev as bonding master. This potentially triggers the message: "bondX received packet on queue Y, but number of RX queues is Z" whenever the queue that packet is received on is higher than the numrxqueues on bonding master (Y > Z). Fixes: 6a9e461f ("bonding: pass link-local packets to bonding master also.") Reported-by:
John Sperbeck <jsperbeck@google.com> Signed-off-by:
Mahesh Bandewar <maheshb@google.com> Signed-off-by:
-
Mahesh Bandewar authored
[ Upstream commit 6a9e461f ] Commit b89f04c6 ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on") changed the behavior of how link-local-multicast packets are processed. The change in the behavior broke some legacy use cases where these packets are expected to arrive on bonding master device also. This patch passes the packet to the stack with the link it arrived on as well as passes to the bonding-master device to preserve the legacy use case. Fixes: b89f04c6 ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on") Reported-by:
Michal Soltys <soltys@ziu.info> Signed-off-by:
-
Eran Ben Elisha authored
[ Upstream commit 11aa5800 ] The code that deals with eswitch vport bw guarantee was going beyond the eswitch vport array limit, fix that. This was pointed out by the kernel address sanitizer (KASAN). The error from KASAN log: [2018-09-15 15:04:45] BUG: KASAN: slab-out-of-bounds in mlx5_eswitch_set_vport_rate+0x8c1/0xae0 [mlx5_core] Fixes: c9497c98 ("net/mlx5: Add support for setting VF min rate") Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
