The WM831x and WM832x series of PMICs contain a flexible clocking
subsystem intended to provide always on and system core clocks.  It
features:

- A 32.768kHz crystal oscillator which can optionally be used to pass
  through an externally generated clock.
- A FLL which can be clocked from either the 32.768kHz oscillator or
  the CLKIN pin.
- A CLKOUT pin which can bring out either the oscillator or the FLL
  output.
- The 32.768kHz clock can also optionally be brought out on the GPIO
  pins of the device.

This driver fully supports the 32.768kHz oscillator and CLKOUT.  The FLL
is supported only in AUTO mode, the full flexibility of the FLL cannot
currently be used.

Due to a lack of access to systems where the core SoC has been converted
to use the generic clock API this driver has been compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Allow drivers to declare their clk_init_data const, the framework really
shouldn't be modifying the data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Most platforms end up using a mix of basic clock types and
some which use clk_hw_foo struct for filling in custom platform
information when the clocks don't fit into basic types supported.

In platform code, its useful to know if a clock is using a basic
type or clk_hw_foo, which helps platforms know if they can
safely use to_clk_hw_foo to derive the clk_hw_foo pointer from
clk_hw.

Mark all basic clocks with a CLK_IS_BASIC flag.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Some divider clks do not have any obvious relationship
between the divider and the value programmed in the
register. For instance, say a value of 1 could signify divide
by 6 and a value of 2 could signify divide by 4 etc.
Also there are dividers where not all values possible
based on the bitfield width are valid. For instance
a 3 bit wide bitfield can be used to program a value
from 0 to 7. However its possible that only 0 to 4
are valid values.

All these cases need the platform code to pass a simple
table of divider/value tuple, so the framework knows
the exact value to be written based on the divider
calculation and can also do better error checking.

This patch adds support for such rate table based
dividers and as part of the support adds a new
registration function 'clk_register_divider_table()'
and a new macro for static definition
'DEFINE_CLK_DIVIDER_TABLE'.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Quite often dividers and the value programmed in the
register have a relation of 'power of two', something like
value	div
0	1
1	2
2	4
3	8...

Add support for such dividers as part of clk-divider.

The clk-divider flag 'CLK_DIVIDER_POWER_OF_TWO' should be used
to define such clocks.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Pull security docs update from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: Minor improvements to no_new_privs documentation

We already use them for openat() and friends, but fchdir() also wants to
be able to use O_PATH file descriptors.  This should make it comparable
to the O_SEARCH of Solaris.  In particular, O_PATH allows you to access
(not-quite-open) a directory you don't have read persmission to, only
execute permission.

Noticed during development of multithread support for ksh93.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org    # O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Last merge window, we had some updates from Al cleaning up the signal
  restart handling.  These have caused some problems on ARM, and while
  Al has some fixes, we have some concerns with Al's patches but we've
  been unsuccesful with discussing this.

  We have got to the point where we need to do something, and we've
  decided that the best solution is to revert the appropriate commits
  until Al is able to reply to us.

  Also included here are four patches to fix warnings that I've noticed
  in my build system, and one fix for kprobes test code."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: fix warning caused by wrongly typed arm_dma_limit
  ARM: fix warnings about atomic64_read
  ARM: 7440/1: kprobes: only test 'sub pc, pc, #1b-2b+8-2' on ARMv6
  ARM: 7441/1: perf: return -EOPNOTSUPP if requested mode exclusion is unavailable
  ARM: 7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK"
  ARM: 7442/1: Revert "remove unused restart trampoline"
  ARM: fix set_domain() macro
  ARM: fix mach-versatile/pci.c warning

The documentation didn't actually mention how to enable no_new_privs.
This also adds a note about possible interactions between
no_new_privs and LSMs (i.e. why teaching systemd to set no_new_privs
is not necessarily a good idea), and it references the new docs
from include/linux/prctl.h.
Suggested-by: Rob Landley <rob@landley.net>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Merge tag 'ecryptfs-3.5-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Fixes an incorrect access mode check when preparing to open a file in
  the lower filesystem.  This isn't an urgent fix, but it is simple and
  the check was obviously incorrect.

  Also fixes a couple important bugs in the eCryptfs miscdev interface.
  These changes are low risk due to the small number of users that use
  the miscdev interface.  I was able to keep the changes minimal and I
  have some cleaner, more complete changes queued up for the next merge
  window that will build on these patches."

* tag 'ecryptfs-3.5-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Gracefully refuse miscdev file ops on inherited/passed files
  eCryptfs: Fix lockdep warning in miscdev operations
  eCryptfs: Properly check for O_RDONLY flag before doing privileged open

Pull target fixes from Nicholas Bellinger:
 "Two minor target fixes.  There is really nothing exciting and/or
  controversial this time around.

  There's one fix from MDR for a RCU debug warning message within tcm_fc
  code (CC'ed to stable), and a small AC fix for qla_target.c based upon
  a recent Coverity static report.

  Also, there is one other outstanding virtio-scsi LUN scanning bugfix
  that has been uncovered with the in-flight tcm_vhost driver over the
  last days, and that needs to make it into 3.5 final too.  This patch
  has been posted to linux-scsi again here:

    http://marc.info/?l=linux-scsi&m=134160609212542&w=2

  and I've asked James to include it in his next PULL request."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  qla2xxx: print the right array elements in qlt_async_event
  tcm_fc: Resolve suspicious RCU usage warnings

File operations on /dev/ecryptfs would BUG() when the operations were
performed by processes other than the process that originally opened the
file. This could happen with open files inherited after fork() or file
descriptors passed through IPC mechanisms. Rather than calling BUG(), an
error code can be safely returned in most situations.

In ecryptfs_miscdev_release(), eCryptfs still needs to handle the
release even if the last file reference is being held by a process that
didn't originally open the file. ecryptfs_find_daemon_by_euid() will not
be successful, so a pointer to the daemon is stored in the file's
private_data. The private_data pointer is initialized when the miscdev
file is opened and only used when the file is released.

https://launchpad.net/bugs/994247Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>

Based upon Alan's patch from Coverity scan id 793583, these debug
messages in qlt_async_event() should be starting from byte 0, which is
always the Asynchronous Event Status Code from the parent switch statement.

Also, rename reason_code -> login_code following the language used in
2500 FW spec for Port Database Changed (0x8014) -> Port Database Changed
Event Mailbox Register for mailbox[2].
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Use rcu_dereference_protected to tell rcu that the ft_lport_lock
is held during ft_lport_create. This resolved "suspicious RCU usage"
warnings when debugging options are turned on.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Pull two MTD fixes from David Woodhouse:
 - Fix a logic error in OLPC CAFÉ NAND ready() function.
 - Fix regression due to bitflip handling changes.

* tag 'for-linus-20120706' of git://git.infradead.org/linux-mtd:
  mtd: cafe_nand: fix an & vs | mistake
  mtd: nand: initialize bitflip_threshold prior to BBT scanning

Otherwise the code races with munmap (causing a use-after-free
of the vma) or with close (causing a use-after-free of the struct
file).

The bug was introduced by commit 90ed52eb ("[PATCH] holepunch: fix
mmap_sem i_mutex deadlock")

Cc: Hugh Dickins <hugh@veritas.com>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ocfs2 fixes from Joel Becker.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  aio: make kiocb->private NUll in init_sync_kiocb()
  ocfs2: Fix bogus error message from ocfs2_global_read_info
  ocfs2: for SEEK_DATA/SEEK_HOLE, return internal error unchanged if ocfs2_get_clusters_nocache() or ocfs2_inode_lock() call failed.
  ocfs2: use spinlock irqsave for downconvert lock.patch
  ocfs2: Misplaced parens in unlikley
  ocfs2: clear unaligned io flag when dio fails

Pull cifs fixes from Steve French.

* git://git.samba.org/sfrench/cifs-2.6:
  cifs: when server doesn't set CAP_LARGE_READ_X, cap default rsize at MaxBufferSize
  cifs: fix parsing of password mount option

Pull input layer fixes from Dmitry Torokhov:
 "Two fixes for regressions in Wacom driver and fixes for drivers using
  threaded IRQ framework without specifying IRQF_ONESHOT."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: request threaded-only IRQs with IRQF_ONESHOT
  Input: wacom - don't retrieve touch_max when it is predefined
  Input: wacom - fix retrieving touch_max bug
  Input: fix input.h kernel-doc warning

The intent here was clearly to set result to true if the 0x40000000 flag
was set.  But instead there was a | vs & typo and we always set result
to true.

Artem: check the spec at
wiki.laptop.org/images/5/5c/88ALP01_Datasheet_July_2007.pdf
and this fix looks correct.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Pull ARM SoC fixes from Arnd Bergmann:
 "Small fixes on multiple ARM platforms
   - A build regression from a previous fix on dove and mv78xx0
   - Two fixes for recently (3.5-rc1) changed mmp/pxa code
   - multiple omap2+ bug fixes
   - two trivial fixes for i.MX
   - one v3.5 regression for mxs"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: apx4devkit: fix FEC enabling PHY clock
  ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4
  ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks
  ARM: Orion: Fix WDT compile for Dove and MV78xx0
  ARM: mmp: remove mach/gpio-pxa.h
  ARM: imx: assert SCC gate stays enabled
  ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled
  ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure
  ARM: imx27_visstrim_m10: Do not include <asm/system.h>
  ARM: pxa: hx4700: Fix basic suspend/resume

Pull KVM fix from Marcelo Tosatti:
 "Memory leak and oops on the x86 mmu code, and sanitization of the
  KVM_IRQFD ioctl."

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: MMU: fix shrinking page from the empty mmu
  KVM: fix fault page leak
  KVM: Sanitize KVM_IRQFD flags
  KVM: Add missing KVM_IRQFD API documentation
  KVM: Pass kvm_irqfd to functions

Pull leds fix from Bryan Wu:
 "Fix for heartbeat led trigger driver"

* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: heartbeat: fix bug on panic

Pull btrfs updates from Chris Mason:
 "I held off on my rc5 pull because I hit an oops during log recovery
  after a crash.  I wanted to make sure it wasn't a regression because
  we have some logging fixes in here.

  It turns out that a commit during the merge window just made it much
  more likely to trigger directory logging instead of full commits,
  which exposed an old bug.

  The new backref walking code got some additional fixes.  This should
  be the final set of them.

  Josef fixed up a corner where our O_DIRECT writes and buffered reads
  could expose old file contents (not stale, just not the most recent).
  He and Liu Bo fixed crashes during tree log recover as well.

  Ilya fixed errors while we resume disk balancing operations on
  readonly mounts."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: run delayed directory updates during log replay
  Btrfs: hold a ref on the inode during writepages
  Btrfs: fix tree log remove space corner case
  Btrfs: fix wrong check during log recovery
  Btrfs: use _IOR for BTRFS_IOC_SUBVOL_GETFLAGS
  Btrfs: resume balance on rw (re)mounts properly
  Btrfs: restore restriper state on all mounts
  Btrfs: fix dio write vs buffered read race
  Btrfs: don't count I/O statistic read errors for missing devices
  Btrfs: resolve tree mod log locking issue in btrfs_next_leaf
  Btrfs: fix tree mod log rewind of ADD operations
  Btrfs: leave critical region in btrfs_find_all_roots as soon as possible
  Btrfs: always put insert_ptr modifications into the tree mod log
  Btrfs: fix tree mod log for root replacements at leaf level
  Btrfs: support root level changes in __resolve_indirect_ref
  Btrfs: avoid waiting for delayed refs when we must not

Pull DT fixes from Rob Herring:
 "Mainly some documentation updates and 2 fixes:

   - An export symbol fix for of_platform_populate from Stephen W.
   - A fix for the order compatible entries are matched to ensure the
     first compatible string is matched when there are multiple matches."

Normally these would go through Grant Likely (thus the "fixes-for-grant"
branch name), but Grant is in the middle of moving to Scotland, and is
practically offline until sometime in August. So pull directly from Rob.

* 'fixes-for-grant' of git://sources.calxeda.com/kernel/linux:
  of: match by compatible property first
  dt: mc13xxx.txt: Fix gpio number assignment
  dt: fsl-fec.txt: Fix gpio number assignment
  dt: fsl-mma8450.txt: Add missing 'reg' description
  dt: fsl-imx-esdhc.txt: Fix gpio number assignment
  dt: fsl-imx-cspi.txt: Fix comment about GPIOs used for chip selects
  of: Add Avionic Design vendor prefix
  of: export of_platform_populate()

arch/arm/mm/init.c: In function 'arm_memblock_init':
arch/arm/mm/init.c:380: warning: comparison of distinct pointer types lacks a cast

by fixing the typecast in its definition when DMA_ZONE is disabled.
This was missed in 4986e5c7 (ARM: mm: fix type of the arm_dma_limit
global variable).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix:
net/netfilter/xt_connbytes.c: In function 'connbytes_mt':
net/netfilter/xt_connbytes.c:43: warning: passing argument 1 of 'atomic64_read' discards qualifiers from pointer target type
...

by adding the missing const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

'sub pc, pc, #1b-2b+8-2' results in address<1:0> == '10'.

sub pc, pc, #const (== ADR pc, #const) performs an interworking branch
(BXWritePC()) on ARMv7+ and a simple branch (BranchWritePC()) on earlier
versions.

In ARM state, BXWritePC() is UNPREDICTABLE when address<1:0> == '10'.

In ARM state on ARMv6+, BranchWritePC() ignores address<1:0>.  Before
ARMv6, BranchWritePC() is UNPREDICTABLE if address<1:0> != '00'

So the instruction is UNPREDICTABLE both before and after v6.
Acked-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge tag 'omap-fixes-for-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

PM related fixes for omaps mostly to get suspend/resume
working again.

* tag 'omap-fixes-for-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4
  ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks
  ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled
  ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* 'mxs/fixes-for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: apx4devkit: fix FEC enabling PHY clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

We currently return -EPERM if the user requests mode exclusion that is
not supported by the CPU. This looks pretty confusing from userspace
and is inconsistent with other architectures (ppc, x86).

This patch returns -EOPNOTSUPP instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 6b5c8045.

Conflicts:

	arch/arm/kernel/ptrace.c

The new syscall restarting code can lead to problems if we take an
interrupt in userspace just before restarting the svc instruction. If
a signal is delivered when returning from the interrupt, the
TIF_SYSCALL_RESTARTSYS will remain set and cause any syscalls executed
from the signal handler to be treated as a restart of the previously
interrupted system call. This includes the final sigreturn call, meaning
that we may fail to exit from the signal context. Furthermore, if a
system call made from the signal handler requires a restart via the
restart_block, it is possible to clear the thread flag and fail to
restart the originally interrupted system call.

The right solution to this problem is to perform the restarting in the
kernel, avoiding the possibility of handling a further signal before the
restart is complete. Since we're almost at -rc6, let's revert the new
method for now and aim for in-kernel restarting at a later date.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This reverts commit fa18484d.

We need the restart trampoline back so that we can revert a related
problematic patch 6b5c8045 ("arm: new
way of handling ERESTART_RESTARTBLOCK").
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Avoid polluting drivers with a set_domain() macro, which interferes with
structure member names:

drivers/net/wireless/ath/ath9k/dfs_pattern_detector.c:294:33: error: macro "set_domain" passed 2 arguments, but takes just 1
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Ocfs2 uses kiocb.*private as a flag of unsigned long size. In
commit a11f7e63 ocfs2: serialize unaligned aio, the unaligned
io flag is involved in it to serialize the unaligned aio. As
*private is not initialized in init_sync_kiocb() of do_sync_write(),
this unaligned io flag may be unexpectly set in an aligned dio.
And this will cause OCFS2_I(inode)->ip_unaligned_aio decreased
to -1 in ocfs2_dio_end_io(), thus the following unaligned dio
will hang forever at ocfs2_aiodio_wait() in ocfs2_file_aio_write().
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: stable@vger.kernel.org
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Joel Becker <jlbec@evilplan.org>

Merge tag 'omap-fixes-b-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

A few more OMAP fixes for 3.5-rc.  These fix some bugs with power
management and McBSP.

Ethernet stopped to work after mxs clk framework change.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail. This patch adds the
IRQF_ONESHOT to input drivers where it is missing. Not modified by
this patch are those drivers where the requested IRQ will always be a
nested IRQ (e.g. because it's part of an MFD), since for this special
case IRQF_ONESHOT is not required to be specified when requesting the
IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

arch/arm/mach-versatile/pci.c: In function 'versatile_map_irq':
arch/arm/mach-versatile/pci.c:342: warning: unused variable 'devslot'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>