Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Phonet "universe" only has 64 addresses, so we keep a trivial flat
routing table.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: "Tony Luck" <tony.luck@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lock_kernel/unlock_kernel() in cycle_kernel_lock() which is called
in tun_chr_open() is not serializing against anything and safe to
remove.

tun_chr_fasync() is serialized by get/put_tun() and fasync_helper()
has no dependency on BKL. The modification of tun->flags is racy with
and without the BKL so removing it does not make it worse.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.

With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the driver to accept a MAC address specified in platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5675f221 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 337e067d overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 23d26497 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 59aa3cc4 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since register and onboard memory access has separate
window registers, they need not be kept under same lock.

Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used.  The new access method was
added by commit ea6828b8
("netxen: improve pci memory access").  Firmware init anyway
uses 8-byte strides.

This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bit V_MAC_RX_PL_THRSH(4) was already set a few lines higher.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The negation makes it a bool before the comparison and hence it
will never evaluate to true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking at commit ebc3f64b it appears that this was intended
and not the original, equivalent to `if (facilities.reverse & ~0x81)'.

In x25_parse_facilities() that patch changed how facilities->reverse
was set. No other bits were set than 0x80 and/or 0x01.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added support of private MAC address per port and provisioning
packet handler for iSCSI traffic only.

The above changes are isolated to the cxgb3 driver, independent of any scsi or iscsi driver changes.
Acked-by: Karen Xie <kxie@chelsio.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Runtime PM support to the sh_eth driver.

The clock to the ethernet hardware block will be
enabled as long as the network device is up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:

  struct net_device *alloc_candev(int sizeof_priv,
                                  unsigned int echo_skb_max);

The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of hardcoding NET_IP_ALIGN stuff in various network drivers,
we can add a helper around netdev_alloc_skb()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Storing the mask (size - 1) instead of the size allows fast path to be
a bit faster.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp_poll() can in some circumstances drop frames with incorrect checksums.

Problem is we now have to lock the socket while dropping frames, or risk
sk_forward corruption.

This bug is present since commit 95766fff
([UDP]: Add memory accounting.)

While we are at it, we can correct ioctl(SIOCINQ) to also drop bad frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

I was trying to use TCP_DEFER_ACCEPT and noticed that if the
client does not talk, the connection is never accepted and
remains in SYN_RECV state until the retransmits expire, where
it finally is deleted. This is bad when some firewall such as
netfilter sits between the client and the server because the
firewall sees the connection in ESTABLISHED state while the
server will finally silently drop it without sending an RST.

This behaviour contradicts the man page which says it should
wait only for some time :

       TCP_DEFER_ACCEPT (since Linux 2.4)
          Allows a listener to be awakened only when data arrives
          on the socket.  Takes an integer value  (seconds), this
          can  bound  the  maximum  number  of attempts TCP will
          make to complete the connection. This option should not
          be used in code intended to be portable.

Also, looking at ipv4/tcp.c, a retransmit counter is correctly
computed :

        case TCP_DEFER_ACCEPT:
                icsk->icsk_accept_queue.rskq_defer_accept = 0;
                if (val > 0) {
                        /* Translate value in seconds to number of
                         * retransmits */
                        while (icsk->icsk_accept_queue.rskq_defer_accept < 32 &&
                               val > ((TCP_TIMEOUT_INIT / HZ) <<
                                       icsk->icsk_accept_queue.rskq_defer_accept))
                                icsk->icsk_accept_queue.rskq_defer_accept++;
                        icsk->icsk_accept_queue.rskq_defer_accept++;
                }
                break;

==> rskq_defer_accept is used as a counter of retransmits.

But in tcp_minisocks.c, this counter is only checked. And in
fact, I have found no location which updates it. So I think
that what was intended was to decrease it in tcp_minisocks
whenever it is checked, which the trivial patch below does.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function bond_create_proc_entry is currently of type int.

Two versions of this function exist:

The one in the ifdef CONFIG_PROC_FS branch always return 0.
The one in the else branch (which is empty) return nothing.

When CONFIG_PROC_FS is undef, this cause the following warning:

drivers/net/bonding/bond_main.c: In function `bond_create_proc_entry':
drivers/net/bonding/bond_main.c:3393: warning: control reaches end of
non-void function

No caller of this function use the returned value.

So change the returned type from int to void and remove the
useless return 0; .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3c574_cs:
 spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>