When hid sensor hub is unplugged, there is a crash in
iio_device_unregister_trigger_consumer.
In a typical IIO driver when remove is called, it will unregister and free
trigger and then it will call iio_device_free.
The function iio_trigger_free() will free the allocated memory for trigger.
If this trigger was assigned to iio_dev->trig, then it should be set to NULL.
Othewise when iio_device_free() is called later, it finally calls
iio_device_unregsister_trigger(), which checks for
       if (indio_dev->trig)
                iio_trigger_put(indio_dev->trig);
If indio_dev->trig is not set to NULL, it calls iio_trigger_put on a bad
pointer causing crash.
This scenerio can happen in any driver, which is storing trigger pointer in
iio_dev structure and following current procedure during remove.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

"report_id" is unsigned so it's never less than zero.  These checks can
be removed without any problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

We're holding a spinlock here so we can't call kmalloc() with
GFP_KERNEL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.

Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Properly check the return value of copy_from/to_user() and handle any
errors that might happen.

This removes a bunch of compiler warnings.

Cc: Alois Schlögl <alois.schloegl@ist.ac.at>
Cc: Greg P. Smith <greg@ced.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A basic Lindent run on the .c files, clean up the .h file by hand.

Cc: Alois Schlögl <alois.schloegl@ist.ac.at>
Cc: Greg P. Smith <greg@ced.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the ced1401 driver to the build system.

Yes, there are a lot of warning messages, but it does compile, so it
should be good to get going.

Cc: Alois Schlögl <alois.schloegl@ist.ac.at>
Cc: Greg P. Smith <greg@ced.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a first cut of a TODO file to get this driver out of the
staging directory.

Cc: Alois Schlögl <alois.schloegl@ist.ac.at>
Cc: Greg P. Smith <greg@ced.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes up the usb1401.c file to remove the usage of err() (which is
gone), and the two-argument kmap_atomic() call, and the compat_ioctl
pointer warning.

The code now builds properly, there are lots of warnings still, but it's
a start.

Cc: Alois Schlögl <alois.schloegl@ist.ac.at>
Cc: Greg P. Smith <greg@ced.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This was imported from the
http://pub.ist.ac.at/~schloegl/src/ced1401/.git git repo at the request
of Alois.  The driver originally came from Cambridge Electronic Design
Ltd and was authored by Greg P Smith and others, but Alois did the
maintance work to get it into a semi-building state and pushed to get it
into the main kernel tree here.

Cc: Alois Schlögl <alois.schloegl@ist.ac.at>
Cc: Greg P. Smith <greg@ced.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Quiet some sparse warnings about:

warning: Using plain integer as NULL pointer
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pointer variables should be cleared with NULL on 0. This quiets
some sparse warnings about:

warning: Using plain integer as NULL pointer
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These messages are just added noise.

They also cause some sparse warnings due to MAX_ASICS evaluating
as 1. This causes the local variable 'irq' to be 'unsigned int irq[1]',
which makes the 'irq[1]' access invalid.

Just remove the messages.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function mite_fifo_size() is only referenced in this file. Make
it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The symbol ni_mio_cs_driver is only referenced in this file. Make
it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The symbol labpc_cs_driver and the functions labpc_init_module()
and labpc_exit_module() are only referenced in this file. Make
them static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The symbol dio24_cs_driver is only referenced in this file. Make
it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function ni_pcidio_event() is only referenced in this file.
Make it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function ni_660x_release_mite_channel() is only referenced in
this file. Make it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function read_idm_word() is only referenced in this file.
Make it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Leave the enum's but remove their names. The names are not used
anywhere in the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The functions ni_release_gpct_mite_channel() and ni_prime_channelgain_list()
are only referenced in this file. Make it static.

The function ni_release_gpct_mite_channel() is also only called
when PCIDMA is enabled. Move the #ifdef to quite a sparse warning
about the function not being used.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function do_become_nonbusy() is only referenced in this file.
Make it static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch erases smtc_VRAMBaseAddress variable.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch renames pFramebufferPhysical name to mmio_base.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch improves naming style and comments on smtcfb_info fields.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch annotates iomem pointers.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch improves code legibility after last changes.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting up smtcfb_fix's id happens through smtc_alloc_fb_info. It adds
complexity and unnecesary code.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Part of fb_fix_screeninfo and fb_var_screeninfo initialization happens
in smtc_alloc_fb_info. It duplicates code while hiding the real
functionality of smtc_alloc_fb_info. This patch groups initialization
together.
Signed-off-by: Javier M. Mellid <jmunhoz@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The order of wait values has been changed by commit 9d944ef3.
Fix the wait parameter and start to use a define instead of
"magic number".
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix printk format warning on i386/X86_32 by using 't' for ptrdiff_t.
Also builds cleanly on x86_64.

drivers/staging/csr/csr_wifi_hip_udi.c: In function 'unifi_print_status':
drivers/staging/csr/csr_wifi_hip_udi.c:151:27: warning: format '%ld' expects type 'long int', but argument 5 has type 'int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-v3.7d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

IIO new drivers, features and rework for the 3.7 cycle, 4th set.

Here we have

1) a set cleaning up and moving the ad7476 driver out of staging.
Support for a number of additional parts is also added to that driver.

2) cleanups from various people for the in kernel interface code as that
is getting more an more real use and hence people are picking up on
minor issues that made it through review.  Also a related useful set
of utility functions to avoid duplicate code for converting IIO
representations to other forms.

3) a new fractional type for our read_raw / write_raw functions.
  This allows avoiding loss of accuracy via the in kernel interfaces in some
  cases as well as being rather convenient for a lot of range -> scale
  conversions.

4) New AD5755 DAC driver.

5) Some Blackfin timer trigger improvements including hardware pulse control
for device triggering.

6) Support for the ad7091r in the ad7476 driver.

Add support for the ad7091r 12 bit ADC to the ad7476 driver. Although the
ad7091r is not really related to any of the other devices supported by this
driver, luckily for us there are not so many ways (which are not totally insane)
how sampling a single channel ADC via SPI can be implemented and support for the
ad7091r can be added to the driver with just a few adjustments.

The ad7091r requires an external "conversion start" pulse to start a sample
conversion. After the conversion has finished the result can be read via SPI. We
depend on a IIO trigger to generate this signal, as a result only sampling in
buffered mode and not in manual mode is available.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Some converters require an external signal to start the conversion. This patch
adds support to the bfintmr trigger driver to generate such a signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch hooks up the set_trigger_state callback for the blackfin timer
trigger driver and only enables the timer when a trigger consumer requests it to
be enabled. There really is no reason to keep the timer running and generate
interrupts if nobody is listening to them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

If the timer frequency has not been configured yet get_gptimer_period() will
return 0. Handle this case instead of blindly dividing by the returned value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Use the iio_read_channel_processed function to read the sample value in the
proper unit instead of using iio_read_channel_raw and iio_read_channel_scale and
doing the unit conversion manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>