The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application.  This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction.  The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.

Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00.  I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into work-linus

usb: fixes for v3.6-rc4

Here's a rather big set of fixes for v3.6-rc4.

There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.

We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.

All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.

If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.

In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

renesas_usbhs dma can transport 8byte alignment data, not 4byte.
This patch fixup it.
Reported-by: Sugnan Prabhu S <sugnan.prabhu@renesasmobile.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Earlier we used to check for ep->ep.desc to figure out if this ep has
already been enabled and if so, abort.
Ido Shayevitz removed the usb_endpoint_descriptor from private udc
structure 5a6506f0 ("usb: gadget: Update at91_udc to use
usb_endpoint_descriptor	inside the struct usb_ep") but did not fix up
the ep_enable condition because _now_ the member is always true and we
can't check if this ep is enabled twice.

Cc: Ido Shayevitz <idos@codeaurora.org>
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The driver was converted to the new start/stop interface in f3d8bf34
("usb: gadget: at91_udc: convert to new style start/stop interface").
I overlooked that the driver is overwritting the private data which is
used by the composite framework. The udc driver doesn't read it, it is
only written here.
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.

Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

dma_controller_create() in this MUSB DMA driver only regards 0 as a wrong IRQ
number, despite platform_get_irq_byname() that it calls returns -ENXIO in that
case. It leads to calling request_irq() with a negative IRQ number, and when it
naturally fails, the following is printed to the console:

request_irq -6 failed!

and the DMA controller is not created.

Fix this function to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

when using musb_urb_enqueue to submit three urbs to the same endpoint, when
hep->hcpriv is NULL, qh will be allocated when the first urb is completed.

When the IRQ completes the next two urbs, qh->hep->hcpriv will be set to NULL.
Now the second urb get musb->lock and executes musb_schedule(), but
next_urb(qh) is NULL, so musb_start_urb will Oops.

[ balbi@ti.com : practically rewrote commit log so it makes sense ]
Signed-off-by: mayuzheng <myz147@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Without a reply for USB_DT_BOS the USB3 mode does not work since
448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.).

Cc: stable@vger.kernel.org #v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.

This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.

Cc: stable@vger.kernel.org # v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.

So, cache sync function must not be executed in case of ep0 bounced.

Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If f_fs.c and u_serial.c are combined together using #include, which has
been a common practice so far, the pr_vdebug macro is defined multiple
times. Define it only once.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge tag 'for-usb-linus-2012-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

xHCI 3.6 bug fixes.

Hi Greg,

Here's seven bugfixes for 3.6.  All of them are marked for stable, and
most are vendor-specific fixes.

Details:
--------

 - Commits 052c7f9f and 29636578 fix a couple stupid mistakes I made in a
   Intel xHCI bug fix patch I pushed just before I left for vacation.

 - Commits 29d21457 and a96874a2 fix issues with the Intel Panther Point
   EHCI to xHCI port switchover.

 - Commit 71c731a2 adds the work-around for the TI redriver "dead port"
   issue.

 - Commit 319acdfc adds a fix for non-PCI xHCI platform drivers.

 - Commit e955a1cd works around the UEFI issue with the xHCI host
   sometimes returning 0xff's in the MMIO on boot.

Sarah Sharp

This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device.  The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the number of ports present on the SoC/board is not the maximum
and that the platform data is not filled with all data, there is
an easy way to mess the PIO setup for this interface.
This quick fix addresses mis-configuration in USB host platform data
that is common in at91 boards since commit 0ee6d1ee (USB: ohci-at91:
change maximum number of ports) that did not modified the associatd
board files.
Reported-by: Klaus Falkner <klaus.falkner@solectrix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [3.4+]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>.  It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit b69cc672 added support for the E-861.  After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.

Compiled, but only actually tested on the E-861 and C-867.
Signed-off-by: Éric Piel <piel@delmic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.

Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.

[ balbi@ti.com: slight improvement to commit log ]

This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f4 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.

Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.

This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a "usb: host: xhci:
add platform driver support".
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.

If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.

As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.

For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.

If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.

Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).

This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.

This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset.  The kernels will need to
contain both commit 10d674a8 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd3 "usb: Add support for root hub
port status CAS".  The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.

I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.

This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f4 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.

The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.

There are two more registers that contains the information of the switchable
and non-switchable ports.

This patch adds the checking code for the two register so that only the
switchable ports are altered.

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.

BugLink: http://bugs.launchpad.net/bugs/1000424

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Pull btrfs fixes from Chris Mason:
 "I've split out the big send/receive update from my last pull request
  and now have just the fixes in my for-linus branch.  The send/recv
  branch will wander over to linux-next shortly though.

  The largest patches in this pull are Josef's patches to fix DIO
  locking problems and his patch to fix a crash during balance.  They
  are both well tested.

  The rest are smaller fixes that we've had queued.  The last rc came
  out while I was hacking new and exciting ways to recover from a
  misplaced rm -rf on my dev box, so these missed rc3."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: fix that repair code is spuriously executed for transid failures
  Btrfs: fix ordered extent leak when failing to start a transaction
  Btrfs: fix a dio write regression
  Btrfs: fix deadlock with freeze and sync V2
  Btrfs: revert checksum error statistic which can cause a BUG()
  Btrfs: remove superblock writing after fatal error
  Btrfs: allow delayed refs to be merged
  Btrfs: fix enospc problems when deleting a subvol
  Btrfs: fix wrong mtime and ctime when creating snapshots
  Btrfs: fix race in run_clustered_refs
  Btrfs: don't run __tree_mod_log_free_eb on leaves
  Btrfs: increase the size of the free space cache
  Btrfs: barrier before waitqueue_active
  Btrfs: fix deadlock in wait_for_more_refs
  btrfs: fix second lock in btrfs_delete_delayed_items()
  Btrfs: don't allocate a seperate csums array for direct reads
  Btrfs: do not strdup non existent strings
  Btrfs: do not use missing devices when showing devname
  Btrfs: fix that error value is changed by mistake
  Btrfs: lock extents as we map them in DIO
  ...

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a warning for watchdog-test.c and it will remove a
  duplicate include of delay.h"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: da9052: Remove duplicate inclusion of delay.h
  watchdog: fix watchdog-test.c build warning