Finally we can kill the 'sync_supers' kernel thread along with the
'->write_super()' superblock operation because all the users are gone.
Now every file-system is supposed to self-manage own superblock and
its dirty state.

The nice thing about killing this thread is that it improves power management.
Indeed, 'sync_supers' is a source of monotonic system wake-ups - it woke up
every 5 seconds no matter what - even if there were no dirty superblocks and
even if there were no file-systems using this service (e.g., btrfs and
journalled ext4 do not need it). So it was wasting power most of the time. And
because the thread was in the core of the kernel, all systems had to have it.
So I am quite happy to make it go away.

Interestingly, this thread is a left-over from the pdflush kernel thread which
was a self-forking kernel thread responsible for all the write-back in old
Linux kernels. It was turned into per-block device BDI threads, and
'sync_supers' was a left-over. Thus, R.I.P, pdflush as well.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull exofs update from Boaz Harrosh:
 "They are all mostly fixes, except the most important patch by Artem
  Bityutskiy which removes the use of s_dirt.  After this patch s_dirt
  can be completely removed from the tree."

* 'for-linus' of git://git.open-osd.org/linux-open-osd:
  ore: Fix out-of-bounds access in _ios_obj()
  exofs: Use proper max_IO calculations from ore
  exofs: Fix __r4w_get_page when offset is beyond i_size
  exofs: stop using s_dirt
  exofs: readpage_strip: Add a BUG_ON to check for PageLocked(page)

Pull KVM bug fixes from Marcelo Tosatti:
 - Fix DS/ES segment register corruption on x86_32.
 - Fix kvmclock wallclock migration offset.
 - Fix PIT interrupt ACK vs system reset logic bug.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: VMX: Fix ds/es corruption on i386 with preemption
  KVM: x86: apply kvmclock offset to guest wall clock time
  KVM: PIC: call ack notifiers for irqs that are dropped form irr

Pull sound fixes from Takashi Iwai:
 "A bunch of small fixes for ASoC, mainly against regressions due to the
  defaulting regmap i/o, in addition to a HD-audio fixup."

* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: core: Fix check before defaulting to regmap
  ALSA: hda - Support dock on Lenovo Thinkpad T530 with ALC269VC
  ASoC: wm8962: Allow VMID time to fully ramp
  ASoC: AC97 doesn't use regmap by default
  ASoC: sgtl5000: enable VAG_POWER for LINE_IN
  ASoC: ab8500: Inform SoC Core that we have our own I/O arrangements
  ASoC: omap: Add missing modules aliases to get sound working on omap devices
  sound: tegra_alc5632: Adjust to of_get_named_gpio() change
  sound: tegra_wm8903: Adjust to of_get_named_gpio() change
  ASoC: mc13783: Provide codec->control_data
  ASoC: ux500: Include the correct header files
  ASoC: wm8994: Hold runtime PM reference while handling mic and jack IRQs
  ASoC: sgtl5000: remove unneeded snd_soc_dapm_new_widgets in probe
  ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work
  ASoC: mxs-saif: fix clock prepare and enable unbalance issue
  ASoC: wm8994: Ensure there are enough BCLKs for four channels

Pull futex fixes from Ingo Molnar:
 "A couple of futex fixes from Darren Hart: two bugs reported by Dave
  Jones (found with his trinity test) and Dan Carpenter through static
  analysis.  The third found while debugging the first two."

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Forbid uaddr == uaddr2 in futex_wait_requeue_pi()
  futex: Fix bug in WARN_ON for NULL q.pi_state
  futex: Test for pi_mutex on fault in futex_wait_requeue_pi()

Pull x86 fixes from Ingo Molnar:
 "Various fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-64, kcmp: The kcmp system call can be common
  arch/x86/kernel/kdebugfs.c: Ensure a consistent return value in error case
  x86/mce: Add quirk for instruction recovery on Sandy Bridge processors
  x86/mce: Move MCACOD defines from mce-severity.c to <asm/mce.h>
  x86/ioapic: Fix NULL pointer dereference on CPU hotplug after disabling irqs
  x86, nops: Missing break resulting in incorrect selection on Intel
  x86: CONFIG_CC_STACKPROTECTOR=y is no longer experimental

Pull timer fixes from Ingo Molnar:
 "One regression fix, and a couple of cleanups that clean up the code
  flow in areas that had high-profile bugs recently."

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Remove all direct references to timekeeper
  time: Clean up offs_real/wall_to_mono and offs_boot/total_sleep_time updates
  time: Clean up stray newlines
  time/jiffies: Rename ACTHZ to SHIFTED_HZ
  time/jiffies: Allow CLOCK_TICK_RATE to be undefined
  time: Fix casting issue in tk_set_xtime and tk_xtime_add

Pull scheduler fixes from Ingo Molnar:
 "Fixes and two late cleanups"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cleanups: Add load balance cpumask pointer to 'struct lb_env'
  sched: Fix comment about PREEMPT_ACTIVE bit location
  sched: Fix minor code style issues
  sched: Use task_rq_unlock() in __sched_setscheduler()
  sched/numa: Add SD_PERFER_SIBLING to CPU domain

Pull perf fixes from Ingo Molnar:
 "Fix merge window fallout and fix sleep profiling (this was always
  broken, so it's not a fix for the merge window - we can skip this one
  from the head of the tree)."

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/trace: Add ability to set a target task for events
  perf/x86: Fix USER/KERNEL tagging of samples properly
  perf/x86/intel/uncore: Make UNCORE_PMU_HRTIMER_INTERVAL 64-bit

Pull irq fix from Ingo Molnar.

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Allow irq chips to mark themself oneshot safe

Pull KGDB/KDB/usb-dbgp fixes and cleanups from Jason Wessel:
 "There are no new features, those will be delayed to the 3.7 window.
  There are only fixes/cleanup against the usual kernel churn and we are
  removing more lines than we add:

   - usb-dbgp - increase the controller wait time to come out of halt.
   - kdb - Remove unused KDB_FLAG_ONLY_DO_DUMP code and cpu in more prompt
   - debug core - pass NMI type on archs that provide NMI types"

* tag 'for_linux-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
  USB: echi-dbgp: increase the controller wait time to come out of halt.
  kernel/debug: Make use of KGDB_REASON_NMI
  kdb: Remove cpu from the more prompt
  kdb: Remove unused KDB_FLAG_ONLY_DO_DUMP

Pull m68k updates from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Make sys_atomic_cmpxchg_32 work on classic m68k
  m68k/apollo: Rename "timer" to "apollo_timer"
  zorro: Remove unused zorro_bus.devices
  m68k: Remove never used asm/shm.h
  m68k/sun3: Remove unselectable code in prom_init()
  m68k: Use asm-generic version of <asm/sections.h>
  m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
  mtd/uclinux: Use generic __bss_stop instead of _ebss
  m68knommu: Allow ColdFire CPUs to use unaligned accesses
  m68k: Remove five unused headers
  m68k: CPU32 does not support unaligned accesses
  m68k: Introduce config option CPU_HAS_NO_UNALIGNED
  m68k: delay, muldi3 - Use CONFIG_CPU_HAS_NO_MULDIV64
  m68k: Move CPU_HAS_* config options
  m68k: Remove duplicate FPU config option
  m68knommu: Clean up printing of sections
  m68k: Use asm-generic version of <asm/types.h>
  m68k: Use Kbuild logic to import asm-generic headers

User space access must always go through uaccess accessors, since on
classic m68k user space and kernel space are completely separate.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1

Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
	SIRFSOC_TIMER_LATCH);

Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized.  Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>

ASoC: Additional updates for 3.6

A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.

The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work.  Replace it with a fresh
method.  In particular:

 * always attempt to do an atomic open+lookup, both for the create case
   and for lookups of existing files.
 * fix symlink handling by returning 1 to the VFS so that we can follow
   the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>

_ios_obj() is accessed by group_index not device_table index.

The oc->comps array is only a group_full of devices at a time
it is not like ore_comp_dev() which is indexed by a global
device_table index.

This did not BUG until now because exofs only uses a single
COMP for all devices. But with other FSs like PanFS this is
not true.

This bug was only in the write_path, all other users were
using it correctly

[This is a bug since 3.2 Kernel]
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

exofs_max_io_pages should just use the ORE's
calculated layout->max_io_length,

And avoid unnecessary BUGs, calculations made here were
also a layering violation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

It is very common for the end of the file to be unaligned on
stripe size. But since we know it's beyond file's end then
the XOR should be preformed with all zeros.

Old code used to just read zeros out of the OSD devices, which is a great
waist. But what scares me more about this situation is that, we now have
pages attached to the file's mapping that are beyond i_size. I don't
like the kind of bugs this calls for.

Fix both birds, by returning a global ZERO_PAGE, if offset is beyond
i_size.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

Exofs has the '->write_super()' handler and makes some use of the '->s_dirt'
superblock flag, but it really needs neither of them because it never sets
's_dirt' to one which means the VFS never calls its '->write_super()' handler.
Thus, remove both.

Note, I am trying to remove both 's_dirt' and 'write_super()' from VFS
altogether once all users are gone.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

readpage_strip can be called from several code paths all of which
require that the page be locked before any operations are carried
out.

Since we export the exofs_readpage callback to the VFS, add a
BUG_ON to check for PageLocked(page) to make sure that this
understanding is never compromised.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

Check if the chip has provided a write operation (which is mandatory for
I/O) rather than looking for control data as some of the MFDs use a global
for this. Also skip the attempt if there's no regmap available by device
in case things get confused by the attempt to default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

Lenovo Thinkpad T530 with ALC269VC codec has a dock port but BIOS
doesn't set up the pins properly.  Enable the pins as well as on
Thinkpad X230 Tablet.
Reported-and-tested-by: Mario <anyc@hadiko.de>
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Pull MIPS updates from Ralf Baechle:
 "The lion share of this pull request are fixes for clk-related breakage
  caused by other changes during this merge window.  For some platforms
  the fix was as simple as selecting HAVE_CLK, for others like the
  Loongson 2 significant restructuring was required.

  The remainder are changes required to get the Lantiq code to work
  again."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Loongson 2: Sort out clock managment.
  MIPS: Loongson 1: more clk support and add select HAVE_CLK
  MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: Lantiq: Platform specific CLK fixup
  MIPS: Lantiq: Add device_tree_init function
  MIPS: Lantiq: Fix interface clock and PCI control register offset

Pull UML fixes from Richard Weinberger:
 "This patch set contains mostly fixes and cleanups.  The UML tty driver
  uses now tty_port and is no longer broken like hell  :-)"

* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Add arch/x86/um to MAINTAINERS
  um: pass siginfo to guest process
  um: fix ubd_file_size for read-only files
  um: pull interrupt_end() into userspace()
  um: split syscall_trace(), pass pt_regs to it
  um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
  um: set BLK_CGROUP=y in defconfig
  um: remove count_lock
  um: fully use tty_port
  um: Remove dead code
  um: remove line_ioctl()
  TTY: um/line, use tty from tty_port
  TTY: um/line, add tty_port