When failed to init rxq or txq in mv643xx_eth_open() for opening device,
napi isn't disabled. When open mv643xx_eth device next time, it will
trigger a BUG_ON() in napi_enable(). Compile tested only.

Fixes: 2257e05c ("mv643xx_eth: get rid of receive-side locking")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221109025432.80900-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When failed to start nic or add interrupt service routine in
s2io_card_up() for opening device, napi isn't disabled. When open
s2io device next time, it will trigger a BUG_ON()in napi_enable().
Compile tested only.

Fixes: 5f490c96 ("S2io: Fixed synchronization between scheduling of napi with card reset and close")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221109023741.131552-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Antoine Tenart says:

====================
macsec: clear encryption keys in h/w drivers

Commit aaab73f8 ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading but some h/w drivers did a copy of the key
which need to be zeroed as well.

The MSCC PHY driver can actually be converted not to copy the encryption
key at all, but such patch would be quite difficult to backport. I'll
send a following up patch doing this in net-next once this series lands.

Tested on the MSCC PHY but not on the atlantic NIC.
====================

Link: https://lore.kernel.org/r/20221108153459.811293-1-atenart@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit aaab73f8 ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the atlantic driver made a copy and did
not clear it. Fix this.

[4 Fixes tags below, all part of the same series, no need to split this]

Fixes: 9ff40a75 ("net: atlantic: MACSec ingress offload implementation")
Fixes: b8f8a0b7 ("net: atlantic: MACSec ingress offload HW bindings")
Fixes: 27736563 ("net: atlantic: MACSec egress offload implementation")
Fixes: 9d106c6d ("net: atlantic: MACSec egress offload HW bindings")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Commit aaab73f8 ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the MSCC PHY driver made a copy, kept
it in the flow data and did not clear it when freeing a flow. Fix this.

Fixes: 28c5107a ("net: phy: mscc: macsec support")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Yang Yingliang says:

====================
stmmac: dwmac-loongson: fixes three leaks

patch #2 fixes missing pci_disable_device() in the error path in probe()
patch #1 and pach #3 fix missing pci_disable_msi() and of_node_put() in
error and remove() path.
====================

Link: https://lore.kernel.org/r/20221108114647.4144952-1-yangyingliang@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The node returned by of_get_child_by_name() with refcount decremented,
of_node_put() needs be called when finish using it. So add it in the
error path in loongson_dwmac_probe() and in loongson_dwmac_remove().

Fixes: 2ae34111 ("stmmac: dwmac-loongson: fix invalid mdio_node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add missing pci_disable_device() in the error path in loongson_dwmac_probe().

Fixes: 30bba69d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

pci_enable_msi() has been called in loongson_dwmac_probe(),
so pci_disable_msi() needs be called in remove path and error
path of probe().

Fixes: 30bba69d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

When t4vf_update_port_info() failed in cxgb4vf_open(), resources applied
during adapter goes up are not cleared. Fix it. Only be compiled, not be
tested.

Fixes: 18d79f72 ("cxgb4vf: Update port information in cxgb4vf_open()")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221109012100.99132-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If mctp_neigh_init() return error, the routes resources should
be released in the error handling path. Otherwise some resources
leak.

Fixes: 4d8b9319 ("mctp: Add neighbour implementation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20221108095517.620115-1-weiyongjun@huaweicloud.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Current Intel platform has an output of ~976ms interval
when probed on 1 Pulse-per-Second(PPS) hardware pin.

The correct PTP clock frequency for PCH GbE should be 204.8MHz
instead of 200MHz. PSE GbE PTP clock rate remains at 200MHz.

Fixes: 58da0cfa ("net: stmmac: create dwmac-intel.c to contain all Intel platform")
Signed-off-by: Ling Pei Lee <pei.lee.ling@intel.com>
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Gan Yi Fang <yi.fang.gan@intel.com>
Link: https://lore.kernel.org/r/20221108020811.12919-1-yi.fang.gan@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When failed to bind qsets in cxgb_up() for opening device, napi isn't
disabled. When open cxgb3 device next time, it will trigger a BUG_ON()
in napi_enable(). Compile tested only.

Fixes: 48c4b6db ("cxgb3 - fix port up/down error path")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221109021451.121490-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When failed to create xdp rxqs or fill rx channels in cpsw_ndo_open() for
opening device, napi isn't disabled. When open cpsw device next time, it
will report a invalid opcode issue. Compiled tested only.

Fixes: d354eb85 ("drivers: net: cpsw: dual_emac: simplify napi usage")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221109011537.96975-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter fixes for net:

1) Fix deadlock in nfnetlink due to missing mutex release in error path,
   from Ziyang Xuan.

2) Clean up pending autoload module list from nf_tables_exit_net() path,
   from Shigeru Yoshida.

3) Fixes for the netfilter's reverse path selftest, from Phil Sutter.

All of these bugs have been around for several releases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

M Chetan Kumar says:

====================
net: wwan: iosm: fixes

This patch series contains iosm fixes.

PATCH1: Fix memory leak in ipc_pcie_read_bios_cfg.

PATCH2: Fix driver not working with INTEL_IOMMU disabled config.

PATCH3: Fix invalid mux header type.

PATCH4: Fix kernel build robot reported errors.

Please refer to individual commit message for details.

--
v2:
 * PATCH1: No Change
 * PATCH2: Kconfig change
           - Add dependency on PCI to resolve kernel build robot errors.
 * PATCH3: No Change
 * PATCH4: New (Fix kernel build robot errors)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Include linux/vmalloc.h in iosm_ipc_coredump.c &
iosm_ipc_devlink.c to resolve kernel test robot errors.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Data stall seen during peak DL throughput test & packets are
dropped by mux layer due to invalid header type in datagram.

During initlization Mux aggregration protocol is set to default
UL/DL size and TD count of Mux lite protocol. This configuration
mismatch between device and driver is resulting in data stall/packet
drops.

Override the UL/DL size and TD count for Mux aggregation protocol.

Fixes: 1f52d7b6 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With INTEL_IOMMU disable config or by forcing intel_iommu=off from
grub some of the features of IOSM driver like browsing, flashing &
coredump collection is not working.

When driver calls DMA API - dma_map_single() for tx transfers. It is
resulting in dma mapping error.

Set the device DMA addressing capabilities using dma_set_mask() and
remove the INTEL_IOMMU dependency in kconfig so that driver follows
the platform config either INTEL_IOMMU enable or disable.

Fixes: f7af616c ("net: iosm: infrastructure")
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipc_pcie_read_bios_cfg() is using the acpi_evaluate_dsm() to
obtain the wwan power state configuration from BIOS but is
not freeing the acpi_object. The acpi_evaluate_dsm() returned
acpi_object to be freed.

Free the acpi_object after use.

Fixes: 7e98d785 ("net: iosm: entry point")
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Address a few problems with the initial test script version:

* On systems with ip6tables but no ip6tables-legacy, testing for
  ip6tables was disabled by accident.
* Firewall setup phase did not respect possibly unavailable tools.
* Consistently call nft via '$nft'.

Fixes: 6e31ce83 ("selftests: netfilter: Test reverse path filtering")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Previously, the default number of transmit queues was 16. Due to
resource concerns, set to 8 queues instead. Still allow the user
to set more queues (max 16) if they like.

Since the driver is virtualized away from the physical NIC, the purpose
of multiple queues is purely to allow for parallel calls to the
hypervisor. Therefore, there is no noticeable effect on performance by
reducing queue count to 8.

Fixes: d926793c ("ibmveth: Implement multi queue on xmit")
Reported-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20221107203215.58206-1-nnac123@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When failed to enable interrupts in nixge_open() for opening device,
napi isn't disabled. When open nixge device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.

Fixes: 492caffa ("net: ethernet: nixge: Add support for National Instruments XGE netdev")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221107101443.120205-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

A recent patch exposed another issue in napi_get_frags()
caught by syzbot [1]

Before feeding packets to GRO, and calling napi_complete()
we must first grab NAPI_STATE_SCHED.

[1]
WARNING: CPU: 0 PID: 3612 at net/core/dev.c:6076 napi_complete_done+0x45b/0x880 net/core/dev.c:6076
Modules linked in:
CPU: 0 PID: 3612 Comm: syz-executor408 Not tainted 6.1.0-rc3-syzkaller-00175-g1118b204 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
RIP: 0010:napi_complete_done+0x45b/0x880 net/core/dev.c:6076
Code: c1 ea 03 0f b6 14 02 4c 89 f0 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 24 04 00 00 41 89 5d 1c e9 73 fc ff ff e8 b5 53 22 fa <0f> 0b e9 82 fe ff ff e8 a9 53 22 fa 48 8b 5c 24 08 31 ff 48 89 de
RSP: 0018:ffffc90003c4f920 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 0000000000000030 RCX: 0000000000000000
RDX: ffff8880251c0000 RSI: ffffffff875a58db RDI: 0000000000000007
RBP: 0000000000000001 R08: 0000000000000007 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: ffff888072d02628
R13: ffff888072d02618 R14: ffff888072d02634 R15: 0000000000000000
FS: 0000555555f13300(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055c44d3892b8 CR3: 00000000172d2000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
napi_complete include/linux/netdevice.h:510 [inline]
tun_get_user+0x206d/0x3a60 drivers/net/tun.c:1980
tun_chr_write_iter+0xdb/0x200 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:2191 [inline]
do_iter_readv_writev+0x20b/0x3b0 fs/read_write.c:735
do_iter_write+0x182/0x700 fs/read_write.c:861
vfs_writev+0x1aa/0x630 fs/read_write.c:934
do_writev+0x133/0x2f0 fs/read_write.c:977
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f37021a3c19

Fixes: 1118b204 ("net: tun: Fix memory leaks of napi_get_frags")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/20221107180011.188437-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When prestera_sdma_switch_init() failed, the memory pointed to by
sw->rxtx isn't released. Fix it. Only be compiled, not be tested.

Fixes: 501ef306 ("net: marvell: prestera: Add driver for Prestera family ASIC devices")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20221108025607.338450-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-fixes-for-6.1-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
can 2022-11-07

The first patch is by Chen Zhongjin and adds a missing
dev_remove_pack() to the AF_CAN protocol.

Zhengchao Shao's patch fixes a potential NULL pointer deref in
AF_CAN's can_rx_register().

The next patch is by Oliver Hartkopp and targets the CAN ISO-TP
protocol, and fixes the state handling for echo TX processing.

Oliver Hartkopp's patch for the j1939 protocol adds a missing
initialization of the CAN headers inside outgoing skbs.

Another patch by Oliver Hartkopp fixes an out of bounds read in the
check for invalid CAN frames in the xmit callback of virtual CAN
devices. This touches all non virtual device drivers as we decided to
rename the function requiring that netdev_priv points to a struct
can_priv.
(Note: This patch will create a merge conflict with net-next where the
 pch_can driver has removed.)

The last patch is by Geert Uytterhoeven and adds the missing ECC error
checks for the channels 2-7 in the rcar_canfd driver.

* tag 'linux-can-fixes-for-6.1-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
  can: rcar_canfd: Add missing ECC error checks for channels 2-7
  can: dev: fix skb drop check
  can: j1939: j1939_send_one(): fix missing CAN header initialization
  can: isotp: fix tx state handling for echo tx processing
  can: af_can: fix NULL pointer dereference in can_rx_register()
  can: af_can: can_exit(): add missing dev_remove_pack() of canxl_packet
====================

Link: https://lore.kernel.org/r/20221107133217.59861-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reported a warning like below [1]:

WARNING: CPU: 3 PID: 9 at net/netfilter/nf_tables_api.c:10096 nf_tables_exit_net+0x71c/0x840
Modules linked in:
CPU: 2 PID: 9 Comm: kworker/u8:0 Tainted: G        W          6.1.0-rc3-00072-g8e5423e9 #47
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
Workqueue: netns cleanup_net
RIP: 0010:nf_tables_exit_net+0x71c/0x840
...
Call Trace:
 <TASK>
 ? __nft_release_table+0xfc0/0xfc0
 ops_exit_list+0xb5/0x180
 cleanup_net+0x506/0xb10
 ? unregister_pernet_device+0x80/0x80
 process_one_work+0xa38/0x1730
 ? pwq_dec_nr_in_flight+0x2b0/0x2b0
 ? rwlock_bug.part.0+0x90/0x90
 ? _raw_spin_lock_irq+0x46/0x50
 worker_thread+0x67e/0x10e0
 ? process_one_work+0x1730/0x1730
 kthread+0x2e5/0x3a0
 ? kthread_complete_and_exit+0x40/0x40
 ret_from_fork+0x1f/0x30
 </TASK>

In nf_tables_exit_net(), there is a case where nft_net->commit_list is
empty but nft_net->module_list is not empty.  Such a case occurs with
the following scenario:

1. nfnetlink_rcv_batch() is called
2. nf_tables_newset() returns -EAGAIN and NFNL_BATCH_FAILURE bit is
   set to status
3. nf_tables_abort() is called with NFNL_ABORT_AUTOLOAD
   (nft_net->commit_list is released, but nft_net->module_list is not
   because of NFNL_ABORT_AUTOLOAD flag)
4. Jump to replay label
5. netlink_skb_clone() fails and returns from the function (this is
   caused by fault injection in the reproducer of syzbot)

This patch fixes this issue by calling __nf_tables_abort() when
nft_net->module_list is not empty in nf_tables_exit_net().

Fixes: eb014de4 ("netfilter: nf_tables: autoload modules from the abort path")
Link: https://syzkaller.appspot.com/bug?id=802aba2422de4218ad0c01b46c9525cc9d4e4aa3 [1]
Reported-by: syzbot+178efee9e2d7f87f5103@syzkaller.appspotmail.com
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>

When type is NFNL_CB_MUTEX and -EAGAIN error occur in nfnetlink_rcv_msg(),
it does not execute nfnl_unlock(). That would trigger potential dead lock.

Fixes: 50f2db9e ("netfilter: nfnetlink: consolidate callback types")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Florian Westphal <fw@strlen.de>

When failed to register irq in xgene_enet_open() for opening device,
napi isn't disabled. When open xgene device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.

Fixes: aeb20b6b ("drivers: net: xgene: fix: ifconfig up/down crash")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221107043032.357673-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Current way of checking available SQE count which is based on
HW updated SQB count could result in driver submitting an SQE
even before CQE for the previously transmitted SQE at the same
index is processed in NAPI resulting losing SKB pointers,
hence a leak. Fix this by checking a consumer index which
is updated once CQE is processed.

Fixes: 3ca6c4c8 ("octeontx2-pf: Add packet transmission support")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20221107033505.2491464-1-rkannoth@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When failed to connect to and start PHY in mtk_star_enable() for opening
device, napi isn't disabled. When open mtk star device next time, it will
reports a invalid opcode issue. Fix it. Only be compiled, not be tested.

Fixes: 8c7bd5a4 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221107012159.211387-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

If lapb_register() failed when lapb device goes to up for the first time,
the NAPI is not disabled. As a result, the invalid opcode issue is
reported when the lapb device goes to up for the second time.

The stack info is as follows:
[ 1958.311422][T11356] kernel BUG at net/core/dev.c:6442!
[ 1958.312206][T11356] invalid opcode: 0000 [#1] PREEMPT SMP KASAN
[ 1958.315979][T11356] RIP: 0010:napi_enable+0x16a/0x1f0
[ 1958.332310][T11356] Call Trace:
[ 1958.332817][T11356]  <TASK>
[ 1958.336135][T11356]  lapbeth_open+0x18/0x90
[ 1958.337446][T11356]  __dev_open+0x258/0x490
[ 1958.341672][T11356]  __dev_change_flags+0x4d4/0x6a0
[ 1958.345325][T11356]  dev_change_flags+0x93/0x160
[ 1958.346027][T11356]  devinet_ioctl+0x1276/0x1bf0
[ 1958.346738][T11356]  inet_ioctl+0x1c8/0x2d0
[ 1958.349638][T11356]  sock_ioctl+0x5d1/0x750
[ 1958.356059][T11356]  __x64_sys_ioctl+0x3ec/0x1790
[ 1958.365594][T11356]  do_syscall_64+0x35/0x80
[ 1958.366239][T11356]  entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 1958.377381][T11356]  </TASK>

Fixes: 514e1150 ("net: x25: Queue received packets in the drivers instead of per-CPU queues")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221107011445.207372-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Xin Long says:

====================
sctp: fix a NULL pointer dereference in sctp_sched_dequeue_common

This issue was triggered with SCTP_PR_SCTP_PRIO in sctp,
and caused by not checking and fixing stream->out_curr
after removing a chunk from this stream.

Patch 1 removes an unnecessary check and makes the real
fix easier to add in Patch 2.
====================

Link: https://lore.kernel.org/r/cover.1667598261.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

A crash was reported by Zhen Chen:

  list_del corruption, ffffa035ddf01c18->next is NULL
  WARNING: CPU: 1 PID: 250682 at lib/list_debug.c:49 __list_del_entry_valid+0x59/0xe0
  RIP: 0010:__list_del_entry_valid+0x59/0xe0
  Call Trace:
   sctp_sched_dequeue_common+0x17/0x70 [sctp]
   sctp_sched_fcfs_dequeue+0x37/0x50 [sctp]
   sctp_outq_flush_data+0x85/0x360 [sctp]
   sctp_outq_uncork+0x77/0xa0 [sctp]
   sctp_cmd_interpreter.constprop.0+0x164/0x1450 [sctp]
   sctp_side_effects+0x37/0xe0 [sctp]
   sctp_do_sm+0xd0/0x230 [sctp]
   sctp_primitive_SEND+0x2f/0x40 [sctp]
   sctp_sendmsg_to_asoc+0x3fa/0x5c0 [sctp]
   sctp_sendmsg+0x3d5/0x440 [sctp]
   sock_sendmsg+0x5b/0x70

and in sctp_sched_fcfs_dequeue() it dequeued a chunk from stream
out_curr outq while this outq was empty.

Normally stream->out_curr must be set to NULL once all frag chunks of
current msg are dequeued, as we can see in sctp_sched_dequeue_done().
However, in sctp_prsctp_prune_unsent() as it is not a proper dequeue,
sctp_sched_dequeue_done() is not called to do this.

This patch is to fix it by simply setting out_curr to NULL when the
last frag chunk of current msg is dequeued from out_curr stream in
sctp_prsctp_prune_unsent().

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: Zhen Chen <chenzhen126@huawei.com>
Tested-by: Caowangbao <caowangbao@huawei.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Since commit 5bbbbe32 ("sctp: introduce stream scheduler foundations"),
sctp_stream_outq_migrate() has been called in sctp_stream_init/update to
removes those chunks to streams higher than the new max. There is no longer
need to do such check in sctp_prsctp_prune_unsent().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is a follow-up for commit 974cb0e3 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.

syzbot reported a call trace because of it:

  BUG: KMSAN: uninit-value in ...
   tipc_nl_compat_name_table_dump+0x841/0xea0 net/tipc/netlink_compat.c:934
   __tipc_nl_compat_dumpit+0xab2/0x1320 net/tipc/netlink_compat.c:238
   tipc_nl_compat_dumpit+0x991/0xb50 net/tipc/netlink_compat.c:321
   tipc_nl_compat_recv+0xb6e/0x1640 net/tipc/netlink_compat.c:1324
   genl_family_rcv_msg_doit net/netlink/genetlink.c:731 [inline]
   genl_family_rcv_msg net/netlink/genetlink.c:775 [inline]
   genl_rcv_msg+0x103f/0x1260 net/netlink/genetlink.c:792
   netlink_rcv_skb+0x3a5/0x6c0 net/netlink/af_netlink.c:2501
   genl_rcv+0x3c/0x50 net/netlink/genetlink.c:803
   netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
   netlink_unicast+0xf3b/0x1270 net/netlink/af_netlink.c:1345
   netlink_sendmsg+0x1288/0x1440 net/netlink/af_netlink.c:1921
   sock_sendmsg_nosec net/socket.c:714 [inline]
   sock_sendmsg net/socket.c:734 [inline]

Reported-by: syzbot+e5dbaaa238680ce206ea@syzkaller.appspotmail.com
Fixes: 974cb0e3 ("tipc: fix uninit-value in tipc_nl_compat_name_table_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/ccd6a7ea801b15aec092c3b532a883b4c5708695.1667594933.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

While BCMGENET select BROADCOM_PHY as y, but PTP_1588_CLOCK_OPTIONAL is m,
kconfig warning and build errors:

WARNING: unmet direct dependencies detected for BROADCOM_PHY
  Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
  Selected by [y]:
  - BCMGENET [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_BROADCOM [=y] && HAS_IOMEM [=y] && ARCH_BCM2835 [=y]

drivers/net/phy/broadcom.o: In function `bcm54xx_suspend':
broadcom.c:(.text+0x6ac): undefined reference to `bcm_ptp_stop'
drivers/net/phy/broadcom.o: In function `bcm54xx_phy_probe':
broadcom.c:(.text+0x784): undefined reference to `bcm_ptp_probe'
drivers/net/phy/broadcom.o: In function `bcm54xx_config_init':
broadcom.c:(.text+0xd4c): undefined reference to `bcm_ptp_config_init'

Fixes: 99addbe3 ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20221105090245.8508-1-yuehaibing@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If CONFIG_MACSEC=m and CONFIG_OCTEONTX2_PF=y, it leads a build error:

  ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_pfaf_mbox_up_handler':
  otx2_pf.c:(.text+0x181c): undefined reference to `cn10k_handle_mcs_event'
  ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_probe':
  otx2_pf.c:(.text+0x437e): undefined reference to `cn10k_mcs_init'
  ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_remove':
  otx2_pf.c:(.text+0x5031): undefined reference to `cn10k_mcs_free'
  ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_mbox_up_handler_mcs_intr_notify':
  otx2_pf.c:(.text+0x5f11): undefined reference to `cn10k_handle_mcs_event'

Make CONFIG_OCTEONTX2_PF depends on CONFIG_MACSEC to fix it. Because
it has empty stub functions of cn10k, CONFIG_OCTEONTX2_PF can be enabled
if CONFIG_MACSEC is disabled

Fixes: c54ffc73 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221105063442.2013981-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

While working on the nvmem description I figured out this file had the
"nvmem-cell-names" property name misspelled. Fix the typo, as
"nvmem-cells-names" has never existed.

Fixes: 603094b2 ("dt-bindings: net: Add tsnep Ethernet controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221104162147.1288230-1-miquel.raynal@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There are two problems with meson8b_devm_clk_prepare_enable(),
introduced in commit a54dc4a4 ("net: stmmac: dwmac-meson8b:
Make the clock enabling code re-usable"):

- It doesn't pass the clk argument, but instead always the
  rgmii_tx_clk of the device.

- It silently ignores the return value of devm_add_action_or_reset().

The former didn't become an actual bug until another user showed up in
the next commit 9308c476 ("net: stmmac: dwmac-meson8b: add support
for the RX delay configuration"). The latter means the callers could
end up with the clock not actually prepared/enabled.

Fixes: a54dc4a4 ("net: stmmac: dwmac-meson8b: Make the clock enabling code re-usable")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221104083004.2212520-1-linux@rasmusvillemoes.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>