Some PWMs are disabled by default or the default pin setting
does not match the LED_OFF state (e.g., active-low leds).
Hence, the driver may end up reporting 0 brightness, but
the leds are actually on using full brightness, because
it never enforces its default configuration.
So enforce it by calling led_pwm_set() after successfully
registering the device.

Tested on a Phytec phyFLEX i.MX6Q board based on kernel
v3.19.5.
Signed-off-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Tested-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

The header of this file fixes the license to GPL 2 only without the
option to use later version. So use the string "GPL v2" that is to be
used in this case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

The transient trigger duration is documented to be in msec units, but is
actually in jiffies units. Other time based triggers are in msec units
as well. Fix the timer setup to convert from msec.

This could break an existing userspace that worked around this problem,
but exposing jiffies to userspace is just wrong and would break anyway
if HZ is changed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Raphael Assenat <raph@8d.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Raphael Assenat <raph@8d.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Reviewed-by: Mark Brown <broonie@kernel.org>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Work queues are not used in this driver, so remove the include.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: Ricardo Ribalda <ricardo.ribalda@gmail.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Milo Kim <milo.kim@ti.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Johan Hovold <johan@kernel.org>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Jan-Simon Moeller <dl9pf@gmx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

LED subsystem shifted responsibility for choosing between SYNC or ASYNC
way of setting brightness from drivers to the caller. Adapt the wrapper
to those changes.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: linux-media@vger.kernel.org
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>

Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>

This patch adds description of the LED subsystem API for
setting an LED brightness.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>

This patch removes SET_BRIGHTNESS_ASYNC and SET_BRIGHTNESS_SYNC flags.
led_set_brightness() now calls led_set_brightness_nosleep() instead of
choosing between sync and async op basing on the flags defined by the
driver.

From now on, if a user wants to make sure that brightness will be set
synchronously, they have to use led_set_brightness_sync() API. It is now
being made publicly available since it has become apparent that it is
a caller who should decide whether brightness is to be set in
a synchronous or an asynchronous way.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>

This patch makes LED core capable of setting brightness for drivers
that implement brightness_set_blocking op. It removes from LED class
drivers responsibility for using work queues on their own.

In order to achieve this set_brightness_delayed callback is being
modified to directly call one of available ops for brightness setting.

led_set_brightness_async() function didn't set brightness in an
asynchronous way in all cases. It was mistakenly assuming that all
LED subsystem drivers used work queue in their brightness_set op,
whereas only half of them did that. Since it has no users now,
it is being removed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>

This patch adds led_set_brightness_nosleep() and led_set_brightness_nopm()
functions, that guarantee setting LED brightness in a non-blocking way.
The latter is used from pm_ops context and doesn't modify the brightness
cached in the struct led_classdev. Its execution always ends up with
a call to brightness setting op - either directly or through
a set_brightness_work, regardless of LED_SUSPENDED flag state.

The patch also replaces led_set_brightness_async() with
led_set_brightness_nosleep() in all places where the most vital was setting
brightness in a non sleeping way but not necessarily asynchronously, which
is not needed for non-blocking drivers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The initial purpose of brightness_set_sync op, introduced along with
the LED flash class extension, was to add a means for setting torch LED
brightness as soon as possible, which couldn't have been guaranteed by
brightness_set op. This patch renames the op to brightness_set_blocking,
which describes its purpose in a more generic way. It is beneficial
in view of the prospective changes in the LED core, aiming at removing
the need for using work queues in LED class drivers that can sleep
or use delays while setting brightness.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>

This patch adds LED_BLINK_BRIGHTNESS_CHANGE flag to indicate that blink
brightness has changed, and LED_BLINK_DISABLE flag to indicate that
blinking deactivation has been requested. In order to use the flags
led_timer_function and set_brightness_delayed callbacks as well as
led_set_brightness() function are being modified. The main goal of these
modifications is to prepare set_brightness_work for extension of the
scope of its responsibilities.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>

LED core has a mixture of EXPORT_SYMBOL and EXPORT_SYMBOL_GPL macros.
This patch fixes this discrepancy and switches to using EXPORT_SYMBOL_GPL
for each exported function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>