- 09 Mar, 2016 28 commits
-
-
Arindam Nath authored
commit 0b39c531 upstream. In amdgpu_connector_hotplug(), we need to start DP link training only after we have received DPCD. The function amdgpu_atombios_dp_get_dpcd() returns non-zero value only when an error condition is met, otherwise returns zero. So in case the function encounters an error, we need to skip rest of the code and return from amdgpu_connector_hotplug() immediately. Only when we are successfull in reading DPCD pin, we should carry on with turning-on the monitor. Signed-off-by:
Arindam Nath <arindam.nath@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Chunming Zhou authored
commit 9cac5373 upstream. Select between me and pfp properly. Signed-off-by:
Chunming Zhou <David1.Zhou@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Christian König authored
commit feebe91a upstream. We never ported that back to CIK, so we could run into VM faults here. Signed-off-by:
-
Alex Deucher authored
commit eda1d1cf upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
Jordan Lazare <Jordan.Lazare@amd.com> Acked-by:
-
Alex Deucher authored
commit 5e031d9f upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
-
Timothy Pearson authored
commit 2d02b8bd upstream. During DRAM initialization on certain ASpeed devices, an incorrect bit (bit 10) was checked in the "SDRAM Bus Width Status" register to determine DRAM width. Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05. Signed-off-by:
Timothy Pearson <tpearson@raptorengineeringinc.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Mike Christie authored
commit 8a9ebe71 upstream. In a couple places we are not converting to/from the Linux block layer 512 bytes sectors. 1. The request queue values and what we do are a mismatch of things: max_discard_sectors - This is in linux block layer 512 byte sectors. We are just copying this to max_unmap_lba_count. discard_granularity - This is in bytes. We are converting it to Linux block layer 512 byte sectors. discard_alignment - This is in bytes. We are just copying this over. The problem is that the core LIO code exports these values in spc_emulate_evpd_b0 and we use them to test request arguments in sbc_execute_unmap, but we never convert to the block size we export to the initiator. If we are not using 512 byte sectors then we are exporting the wrong values or are checks are off. And, for the discard_alignment/bytes case we are just plain messed up. 2. blkdev_issue_discard's start and number of sector arguments are supposed to be in linux block layer 512 byte sectors. We are currently passing in the values we get from the initiator which might be based on some other sector size. There is a similar problem in iblock_execute_write_same where the bio functions want values in 512 byte sectors but we are passing in what we got from the initiator. Signed-off-by:
Mike Christie <mchristi@redhat.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [ kamal: backport to 4.4-stable: no unmap_zeroes_data ] Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Joerg Roedel authored
commit e6a8c9b3 upstream. In the PCI hotplug path of the Intel IOMMU driver, replace the usage of the BUS_NOTIFY_DEL_DEVICE notifier, which is executed before the driver is unbound from the device, with BUS_NOTIFY_REMOVED_DEVICE, which runs after that. This fixes a kernel BUG being triggered in the VT-d code when the device driver tries to unmap DMA buffers and the VT-d driver already destroyed all mappings. Reported-by:
Stefani Seibold <stefani@seibold.net> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Suravee Suthikulpanit authored
commit 38e45d02 upstream. The setup code for the performance counters in the AMD IOMMU driver tests whether the counters can be written. It tests to setup a counter for device 00:00.0, which fails on systems where this particular device is not covered by the IOMMU. Fix this by not relying on device 00:00.0 but only on the IOMMU being present. Signed-off-by:
Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Signed-off-by:
-
Jay Cornwall authored
commit 358875fd upstream. The AMD Family 15h Models 30h-3Fh (Kaveri) BIOS and Kernel Developer's Guide omitted part of the BIOS IOMMU L2 register setup specification. Without this setup the IOMMU L2 does not fully respect write permissions when handling an ATS translation request. The IOMMU L2 will set PTE dirty bit when handling an ATS translation with write permission request, even when PTE RW bit is clear. This may occur by direct translation (which would cause a PPR) or by prefetch request from the ATC. This is observed in practice when the IOMMU L2 modifies a PTE which maps a pagecache page. The ext4 filesystem driver BUGs when asked to writeback these (non-modified) pages. Enable ATS write permission check in the Kaveri IOMMU L2 if BIOS has not. Signed-off-by:
Jay Cornwall <jay@jcornwall.me> Signed-off-by:
-
Michael S. Tsirkin authored
commit 4cad67fc upstream. Calling return copy_to_user(...) in an ioctl will not do the right thing if there's a pagefault: copy_to_user returns the number of bytes not copied in this case. Fix up kvm to do return copy_to_user(...)) ? -EFAULT : 0; everywhere. Acked-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Paolo Bonzini authored
commit 70e4da7a upstream. Commit 172b2386 ("KVM: x86: fix missed hardware breakpoints", 2016-02-10) worked around a case where the debug registers are not loaded correctly on preemption and on the first entry to KVM_RUN. However, Xiao Guangrong pointed out that the root cause must be that KVM_DEBUGREG_BP_ENABLED is not being set correctly. This can indeed happen due to the lazy debug exit mechanism, which does not call kvm_update_dr7. Fix it by replacing the existing loop (more or less equivalent to kvm_update_dr0123) with calls to all the kvm_update_dr* functions. Fixes: 172b2386Reviewed-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit 8160c4e4 upstream. Calling return copy_to_user(...) in an ioctl will not do the right thing if there's a pagefault: copy_to_user returns the number of bytes not copied in this case. Fix up vfio to do return copy_to_user(...)) ? -EFAULT : 0; everywhere. Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Yadan Fan authored
commit 1ee9f4bd upstream. This issue is caused by commit 02323db1 ("cifs: fix cifs_uniqueid_to_ino_t not to ever return 0"), when BITS_PER_LONG is 64 on s390x, the corresponding cifs_uniqueid_to_ino_t() function will cast 64-bit fileid to 32-bit by using (ino_t)fileid, because ino_t (typdefed __kernel_ino_t) is int type. It's defined in arch/s390/include/uapi/asm/posix_types.h #ifndef __s390x__ typedef unsigned long __kernel_ino_t; ... #else /* __s390x__ */ typedef unsigned int __kernel_ino_t; So the #ifdef condition is wrong for s390x, we can just still use one cifs_uniqueid_to_ino_t() function with comparing sizeof(ino_t) and sizeof(u64) to choose the correct execution accordingly. Signed-off-by:
Yadan Fan <ydfan@suse.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Pavel Shilovsky authored
commit 6cc3b242 upstream. For interim responses we only need to parse a header and update a number credits. Now it is done for all SMB2+ command except SMB2_READ which is wrong. Fix this by adding such processing. Signed-off-by:
Pavel Shilovsky <pshilovsky@samba.org> Tested-by:
Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by:
-
Justin Maggard authored
commit deb7deff upstream. When opening a file, SMB2_open() attempts to parse the lease state from the SMB2 CREATE Response. However, the parsing code was not careful to ensure that the create contexts are not empty or invalid, which can lead to out- of-bounds memory access. This can be seen easily by trying to read a file from a OSX 10.11 SMB3 server. Here is sample crash output: BUG: unable to handle kernel paging request at ffff8800a1a77cc6 IP: [<ffffffff8828a734>] SMB2_open+0x804/0x960 PGD 8f77067 PUD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 3 PID: 2876 Comm: cp Not tainted 4.5.0-rc3.x86_64.1+ #14 Hardware name: NETGEAR ReadyNAS 314 /ReadyNAS 314 , BIOS 4.6.5 10/11/2012 task: ffff880073cdc080 ti: ffff88005b31c000 task.ti: ffff88005b31c000 RIP: 0010:[<ffffffff8828a734>] [<ffffffff8828a734>] SMB2_open+0x804/0x960 RSP: 0018:ffff88005b31fa08 EFLAGS: 00010282 RAX: 0000000000000015 RBX: 0000000000000000 RCX: 0000000000000006 RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff88007eb8c8b0 RBP: ffff88005b31fad8 R08: 666666203d206363 R09: 6131613030383866 R10: 3030383866666666 R11: 00000000000002b0 R12: ffff8800660fd800 R13: ffff8800a1a77cc2 R14: 00000000424d53fe R15: ffff88005f5a28c0 FS: 00007f7c8a2897c0(0000) GS:ffff88007eb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: ffff8800a1a77cc6 CR3: 000000005b281000 CR4: 00000000000006e0 Stack: ffff88005b31fa70 ffffffff88278789 00000000000001d3 ffff88005f5a2a80 ffffffff00000003 ffff88005d029d00 ffff88006fde05a0 0000000000000000 ffff88005b31fc78 ffff88006fde0780 ffff88005b31fb2f 0000000100000fe0 Call Trace: [<ffffffff88278789>] ? cifsConvertToUTF16+0x159/0x2d0 [<ffffffff8828cf68>] smb2_open_file+0x98/0x210 [<ffffffff8811e80c>] ? __kmalloc+0x1c/0xe0 [<ffffffff882685f4>] cifs_open+0x2a4/0x720 [<ffffffff88122cef>] do_dentry_open+0x1ff/0x310 [<ffffffff88268350>] ? cifsFileInfo_get+0x30/0x30 [<ffffffff88123d92>] vfs_open+0x52/0x60 [<ffffffff88131dd0>] path_openat+0x170/0xf70 [<ffffffff88097d48>] ? remove_wait_queue+0x48/0x50 [<ffffffff88133a29>] do_filp_open+0x79/0xd0 [<ffffffff8813f2ca>] ? __alloc_fd+0x3a/0x170 [<ffffffff881240c4>] do_sys_open+0x114/0x1e0 [<ffffffff881241a9>] SyS_open+0x19/0x20 [<ffffffff8896e257>] entry_SYSCALL_64_fastpath+0x12/0x6a Code: 4d 8d 6c 07 04 31 c0 4c 89 ee e8 47 6f e5 ff 31 c9 41 89 ce 44 89 f1 48 c7 c7 28 b1 bd 88 31 c0 49 01 cd 4c 89 ee e8 2b 6f e5 ff <45> 0f b7 75 04 48 c7 c7 31 b1 bd 88 31 c0 4d 01 ee 4c 89 f6 e8 RIP [<ffffffff8828a734>] SMB2_open+0x804/0x960 RSP <ffff88005b31fa08> CR2: ffff8800a1a77cc6 ---[ end trace d9f69ba64feee469 ]--- Signed-off-by:
Justin Maggard <jmaggard@netgear.com> Signed-off-by:
-
Jean-Philippe Brucker authored
commit a1e533ec upstream. Since commit 27a4c827 fbcon: use the cursor blink interval provided by vt two attempts have been made at fixing a possible hang caused by cursor_timer_handler. That function registers a timer to be triggered at "jiffies + fbcon_ops.cur_blink_jiffies". A new case had been encountered during initialisation of clcd-pl11x: fbcon_fb_registered do_fbcon_takeover -> do_register_con_driver fbcon_startup (A) add_cursor_timer (with cur_blink_jiffies = 0) -> do_bind_con_driver visual_init fbcon_init (B) cur_blink_jiffies = msecs_to_jiffies(vc->vc_cur_blink_ms); If we take an softirq anywhere between A and B (and we do), cursor_timer_handler executes indefinitely. Instead of patching all possible paths that lead to this case one at a time, fix the issue at the source and initialise cur_blink_jiffies to 200ms when allocating fbcon_ops. This was its default value before aforesaid commit. fbcon_cursor or fbcon_init will refine this value downstream. Signed-off-by:
Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Tested-by:
Scot Doyle <lkml14@scotdoyle.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Owen Hofmann authored
commit 2680d6da upstream. vmx.c writes the TSC_MULTIPLIER field in vmx_vcpu_load, but only when a vcpu has migrated physical cpus. Record the last value written and update in vmx_vcpu_load on any change, otherwise a cpu migration must occur for TSC frequency scaling to take effect. Fixes: ff2c3a18Signed-off-by:
Owen Hofmann <osh@google.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit 0178fd7d upstream. Returning directly whatever copy_to_user(...) or copy_from_user(...) returns may not do the right thing if there's a pagefault: copy_to_user/copy_from_user return the number of bytes not copied in this case, but ioctls need to return -EFAULT instead. Fix up kvm on mips to do return copy_to_user(...)) ? -EFAULT : 0; and return copy_from_user(...)) ? -EFAULT : 0; everywhere. Signed-off-by:
-
Helge Deller authored
commit 98e8b6c9 upstream. Mike Frysinger reported that his ptrace testcase showed strange behaviour on parisc: It was not possible to avoid a syscall and the return value of a syscall couldn't be changed. To modify a syscall number, we were missing to save the new syscall number to gr20 which is then picked up later in assembly again. The effect that the return value couldn't be changed is a side-effect of another bug in the assembly code. When a process is ptraced, userspace expects each syscall to report entrance and exit of a syscall. If a syscall number was given which doesn't exist, we jumped to the normal syscall exit code instead of informing userspace that the (non-existant) syscall exits. This unexpected behaviour confuses userspace and thus the bug was misinterpreted as if we can't change the return value. This patch fixes both problems and was tested on 64bit kernel with 32bit userspace. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: Mike Frysinger <vapier@gentoo.org> Tested-by:
Mike Frysinger <vapier@gentoo.org> Signed-off-by:
-
Murali Karicheri authored
commit 79e3f4a8 upstream. Commit cbce7900 ("PCI: designware: Make driver arch-agnostic") changed the host bridge sysdata pointer from the ARM pci_sys_data to the DesignWare pcie_port structure, and changed pcie-designware.c to reflect that. But it did not change the corresponding code in pci-keystone-dw.c, so it caused crashes on Keystone: Unable to handle kernel NULL pointer dereference at virtual address 00000030 pgd = c0003000 [00000030] *pgd=80000800004003, *pmd=00000000 Internal error: Oops: 206 [#1] PREEMPT SMP ARM CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.2-00139-gb74f926 #2 Hardware name: Keystone PC is at ks_dw_pcie_msi_irq_unmask+0x24/0x58 Change pci-keystone-dw.c to expect sysdata to be the struct pcie_port pointer. [bhelgaas: changelog] Fixes: cbce7900 ("PCI: designware: Make driver arch-agnostic") Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by:
-
Keith Busch authored
commit 5f009d3f upstream. The new queue limit is not used by the majority of block drivers, and should be initialized to 0 for the driver's requested settings to be used. Signed-off-by:
Keith Busch <keith.busch@intel.com> Acked-by:
Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by:
Sagi Grimberg <sagig@mellanox.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Oded Gabbay authored
commit a187f17f upstream. Reviewed-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by:
-
Qu Wenruo authored
commit 0a95b851 upstream. Parameter of trace_btrfs_work_queued() can be freed in its workqueue. So no one use use that pointer after queue_work(). Fix the user-after-free bug by move the trace line before queue_work(). Reported-by:
Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
Qu Wenruo <quwenruo@cn.fujitsu.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Zhao Lei authored
commit e1746e83 upstream. I see no_space in v4.4-rc1 again in xfstests generic/102. It happened randomly in some node only. (one of 4 phy-node, and a kvm with non-virtio block driver) By bisect, we can found the first-bad is: commit bdced438 ("block: setup bi_phys_segments after splitting")' But above patch only triggered the bug by making bio operation faster(or slower). Main reason is in our space_allocating code, we need to commit page writeback before wait it complish, this patch fixed above bug. BTW, there is another reason for generic/102 fail, caused by disable default mixed-blockgroup, I'll fix it in xfstests. Signed-off-by:
Zhao Lei <zhaolei@cn.fujitsu.com> Signed-off-by:
-
Filipe Manana authored
commit c2d6cb16 upstream. While running a stress test I ran into a deadlock when running the delayed iputs at transaction time, which produced the following report and trace: [ 886.399989] ============================================= [ 886.400871] [ INFO: possible recursive locking detected ] [ 886.401663] 4.4.0-rc6-btrfs-next-18+ #1 Not tainted [ 886.402384] --------------------------------------------- [ 886.403182] fio/8277 is trying to acquire lock: [ 886.403568] (&fs_info->delayed_iput_sem){++++..}, at: [<ffffffffa0538823>] btrfs_run_delayed_iputs+0x36/0xbf [btrfs] [ 886.403568] [ 886.403568] but task is already holding lock: [ 886.403568] (&fs_info->delayed_iput_sem){++++..}, at: [<ffffffffa0538823>] btrfs_run_delayed_iputs+0x36/0xbf [btrfs] [ 886.403568] [ 886.403568] other info that might help us debug this: [ 886.403568] Possible unsafe locking scenario: [ 886.403568] [ 886.403568] CPU0 [ 886.403568] ---- [ 886.403568] lock(&fs_info->delayed_iput_sem); [ 886.403568] lock(&fs_info->delayed_iput_sem); [ 886.403568] [ 886.403568] *** DEADLOCK *** [ 886.403568] [ 886.403568] May be due to missing lock nesting notation [ 886.403568] [ 886.403568] 3 locks held by fio/8277: [ 886.403568] #0: (sb_writers#11){.+.+.+}, at: [<ffffffff81174c4c>] __sb_start_write+0x5f/0xb0 [ 886.403568] #1: (&sb->s_type->i_mutex_key#15){+.+.+.}, at: [<ffffffffa054620d>] btrfs_file_write_iter+0x73/0x408 [btrfs] [ 886.403568] #2: (&fs_info->delayed_iput_sem){++++..}, at: [<ffffffffa0538823>] btrfs_run_delayed_iputs+0x36/0xbf [btrfs] [ 886.403568] [ 886.403568] stack backtrace: [ 886.403568] CPU: 6 PID: 8277 Comm: fio Not tainted 4.4.0-rc6-btrfs-next-18+ #1 [ 886.403568] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014 [ 886.403568] 0000000000000000 ffff88009f80f770 ffffffff8125d4fd ffffffff82af1fc0 [ 886.403568] ffff88009f80f830 ffffffff8108e5f9 0000000200000000 ffff88009fd92290 [ 886.403568] 0000000000000000 ffffffff82af1fc0 ffffffff829cfb01 00042b216d008804 [ 886.403568] Call Trace: [ 886.403568] [<ffffffff8125d4fd>] dump_stack+0x4e/0x79 [ 886.403568] [<ffffffff8108e5f9>] __lock_acquire+0xd42/0xf0b [ 886.403568] [<ffffffff810c22db>] ? __module_address+0xdf/0x108 [ 886.403568] [<ffffffff8108eb77>] lock_acquire+0x10d/0x194 [ 886.403568] [<ffffffff8108eb77>] ? lock_acquire+0x10d/0x194 [ 886.403568] [<ffffffffa0538823>] ? btrfs_run_delayed_iputs+0x36/0xbf [btrfs] [ 886.489542] [<ffffffff8148556b>] down_read+0x3e/0x4d [ 886.489542] [<ffffffffa0538823>] ? btrfs_run_delayed_iputs+0x36/0xbf [btrfs] [ 886.489542] [<ffffffffa0538823>] btrfs_run_delayed_iputs+0x36/0xbf [btrfs] [ 886.489542] [<ffffffffa0533953>] btrfs_commit_transaction+0x8f5/0x96e [btrfs] [ 886.489542] [<ffffffffa0521d7a>] flush_space+0x435/0x44a [btrfs] [ 886.489542] [<ffffffffa052218b>] ? reserve_metadata_bytes+0x26a/0x384 [btrfs] [ 886.489542] [<ffffffffa05221ae>] reserve_metadata_bytes+0x28d/0x384 [btrfs] [ 886.489542] [<ffffffffa052256c>] ? btrfs_block_rsv_refill+0x58/0x96 [btrfs] [ 886.489542] [<ffffffffa0522584>] btrfs_block_rsv_refill+0x70/0x96 [btrfs] [ 886.489542] [<ffffffffa053d747>] btrfs_evict_inode+0x394/0x55a [btrfs] [ 886.489542] [<ffffffff81188e31>] evict+0xa7/0x15c [ 886.489542] [<ffffffff81189878>] iput+0x1d3/0x266 [ 886.489542] [<ffffffffa053887c>] btrfs_run_delayed_iputs+0x8f/0xbf [btrfs] [ 886.489542] [<ffffffffa0533953>] btrfs_commit_transaction+0x8f5/0x96e [btrfs] [ 886.489542] [<ffffffff81085096>] ? signal_pending_state+0x31/0x31 [ 886.489542] [<ffffffffa0521191>] btrfs_alloc_data_chunk_ondemand+0x1d7/0x288 [btrfs] [ 886.489542] [<ffffffffa0521282>] btrfs_check_data_free_space+0x40/0x59 [btrfs] [ 886.489542] [<ffffffffa05228f5>] btrfs_delalloc_reserve_space+0x1e/0x4e [btrfs] [ 886.489542] [<ffffffffa053620a>] btrfs_direct_IO+0x10c/0x27e [btrfs] [ 886.489542] [<ffffffff8111d9a1>] generic_file_direct_write+0xb3/0x128 [ 886.489542] [<ffffffffa05463c3>] btrfs_file_write_iter+0x229/0x408 [btrfs] [ 886.489542] [<ffffffff8108ae38>] ? __lock_is_held+0x38/0x50 [ 886.489542] [<ffffffff8117279e>] __vfs_write+0x7c/0xa5 [ 886.489542] [<ffffffff81172cda>] vfs_write+0xa0/0xe4 [ 886.489542] [<ffffffff811734cc>] SyS_write+0x50/0x7e [ 886.489542] [<ffffffff814872d7>] entry_SYSCALL_64_fastpath+0x12/0x6f [ 1081.852335] INFO: task fio:8244 blocked for more than 120 seconds. [ 1081.854348] Not tainted 4.4.0-rc6-btrfs-next-18+ #1 [ 1081.857560] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1081.863227] fio D ffff880213f9bb28 0 8244 8240 0x00000000 [ 1081.868719] ffff880213f9bb28 00ffffff810fc6b0 ffffffff0000000a ffff88023ed55240 [ 1081.872499] ffff880206b5d400 ffff880213f9c000 ffff88020a4d5318 ffff880206b5d400 [ 1081.876834] ffffffff00000001 ffff880206b5d400 ffff880213f9bb40 ffffffff81482ba4 [ 1081.880782] Call Trace: [ 1081.881793] [<ffffffff81482ba4>] schedule+0x7f/0x97 [ 1081.883340] [<ffffffff81485eb5>] rwsem_down_write_failed+0x2d5/0x325 [ 1081.895525] [<ffffffff8108d48d>] ? trace_hardirqs_on_caller+0x16/0x1ab [ 1081.897419] [<ffffffff81269723>] call_rwsem_down_write_failed+0x13/0x20 [ 1081.899251] [<ffffffff81269723>] ? call_rwsem_down_write_failed+0x13/0x20 [ 1081.901063] [<ffffffff81089fae>] ? __down_write_nested.isra.0+0x1f/0x21 [ 1081.902365] [<ffffffff814855bd>] down_write+0x43/0x57 [ 1081.903846] [<ffffffffa05211b0>] ? btrfs_alloc_data_chunk_ondemand+0x1f6/0x288 [btrfs] [ 1081.906078] [<ffffffffa05211b0>] btrfs_alloc_data_chunk_ondemand+0x1f6/0x288 [btrfs] [ 1081.908846] [<ffffffff8108d461>] ? mark_held_locks+0x56/0x6c [ 1081.910409] [<ffffffffa0521282>] btrfs_check_data_free_space+0x40/0x59 [btrfs] [ 1081.912482] [<ffffffffa05228f5>] btrfs_delalloc_reserve_space+0x1e/0x4e [btrfs] [ 1081.914597] [<ffffffffa053620a>] btrfs_direct_IO+0x10c/0x27e [btrfs] [ 1081.919037] [<ffffffff8111d9a1>] generic_file_direct_write+0xb3/0x128 [ 1081.920754] [<ffffffffa05463c3>] btrfs_file_write_iter+0x229/0x408 [btrfs] [ 1081.922496] [<ffffffff8108ae38>] ? __lock_is_held+0x38/0x50 [ 1081.923922] [<ffffffff8117279e>] __vfs_write+0x7c/0xa5 [ 1081.925275] [<ffffffff81172cda>] vfs_write+0xa0/0xe4 [ 1081.926584] [<ffffffff811734cc>] SyS_write+0x50/0x7e [ 1081.927968] [<ffffffff814872d7>] entry_SYSCALL_64_fastpath+0x12/0x6f [ 1081.985293] INFO: lockdep is turned off. [ 1081.986132] INFO: task fio:8249 blocked for more than 120 seconds. [ 1081.987434] Not tainted 4.4.0-rc6-btrfs-next-18+ #1 [ 1081.988534] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1081.990147] fio D ffff880218febbb8 0 8249 8240 0x00000000 [ 1081.991626] ffff880218febbb8 00ffffff81486b8e ffff88020000000b ffff88023ed75240 [ 1081.993258] ffff8802120a9a00 ffff880218fec000 ffff88020a4d5318 ffff8802120a9a00 [ 1081.994850] ffffffff00000001 ffff8802120a9a00 ffff880218febbd0 ffffffff81482ba4 [ 1081.996485] Call Trace: [ 1081.997037] [<ffffffff81482ba4>] schedule+0x7f/0x97 [ 1081.998017] [<ffffffff81485eb5>] rwsem_down_write_failed+0x2d5/0x325 [ 1081.999241] [<ffffffff810852a5>] ? finish_wait+0x6d/0x76 [ 1082.000306] [<ffffffff81269723>] call_rwsem_down_write_failed+0x13/0x20 [ 1082.001533] [<ffffffff81269723>] ? call_rwsem_down_write_failed+0x13/0x20 [ 1082.002776] [<ffffffff81089fae>] ? __down_write_nested.isra.0+0x1f/0x21 [ 1082.003995] [<ffffffff814855bd>] down_write+0x43/0x57 [ 1082.005000] [<ffffffffa05211b0>] ? btrfs_alloc_data_chunk_ondemand+0x1f6/0x288 [btrfs] [ 1082.007403] [<ffffffffa05211b0>] btrfs_alloc_data_chunk_ondemand+0x1f6/0x288 [btrfs] [ 1082.008988] [<ffffffffa0545064>] btrfs_fallocate+0x7c1/0xc2f [btrfs] [ 1082.010193] [<ffffffff8108a1ba>] ? percpu_down_read+0x4e/0x77 [ 1082.011280] [<ffffffff81174c4c>] ? __sb_start_write+0x5f/0xb0 [ 1082.012265] [<ffffffff81174c4c>] ? __sb_start_write+0x5f/0xb0 [ 1082.013021] [<ffffffff811712e4>] vfs_fallocate+0x170/0x1ff [ 1082.013738] [<ffffffff81181ebb>] ioctl_preallocate+0x89/0x9b [ 1082.014778] [<ffffffff811822d7>] do_vfs_ioctl+0x40a/0x4ea [ 1082.015778] [<ffffffff81176ea7>] ? SYSC_newfstat+0x25/0x2e [ 1082.016806] [<ffffffff8118b4de>] ? __fget_light+0x4d/0x71 [ 1082.017789] [<ffffffff8118240e>] SyS_ioctl+0x57/0x79 [ 1082.018706] [<ffffffff814872d7>] entry_SYSCALL_64_fastpath+0x12/0x6f This happens because we can recursively acquire the semaphore fs_info->delayed_iput_sem when attempting to allocate space to satisfy a file write request as shown in the first trace above - when committing a transaction we acquire (down_read) the semaphore before running the delayed iputs, and when running a delayed iput() we can end up calling an inode's eviction handler, which in turn commits another transaction and attempts to acquire (down_read) again the semaphore to run more delayed iput operations. This results in a deadlock because if a task acquires multiple times a semaphore it should invoke down_read_nested() with a different lockdep class for each level of recursion. Fix this by simplifying the implementation and use a mutex instead that is acquired by the cleaner kthread before it runs the delayed iputs instead of always acquiring a semaphore before delayed references are run from anywhere. Fixes: d7c15171 (btrfs: Fix NO_SPACE bug caused by delayed-iput) Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit 0378ba48 upstream. CONFIG_ARCH_SHMOBILE is not only enabled for Renesas ARM platforms (which are DT based and multi-platform), but also on a select set of Renesas SuperH platforms (SH7722/SH7723/SH7724/SH7343/SH7366). Hence since commit 0ba58de2 ("drivers: sh: Get rid of CONFIG_ARCH_SHMOBILE_MULTI"), the legacy clock domain is no longer installed on these SuperH platforms, and module clocks may not be enabled when needed, leading to driver failures. To fix this, add an additional check for CONFIG_OF. Fixes: 0ba58de2 ("drivers: sh: Get rid of CONFIG_ARCH_SHMOBILE_MULTI"). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Al Viro authored
commit a528aca7 upstream. Games with ordering and barriers are way too brittle. Just bump ->d_seq before and after updating ->d_inode and ->d_flags type bits, so that verifying ->d_seq would guarantee they are coherent. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
- 03 Mar, 2016 12 commits
-
-
Greg Kroah-Hartman authored
-
Luca Coelho authored
commit 5e56276e upstream. The firmware can perform a scheduled scan with not matchsets passed, but it can't send notification that results were found. Since the userspace then cannot know when we got new results and the firmware wouldn't trigger a wake in case we are sleeping, it's better not to allow scans without matchsets. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=110831Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Oren Givon authored
commit 006bda75 upstream. Update and fix some 7265 PCI IDs entries. Signed-off-by:
Oren Givon <oren.givon@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 62d7476d upstream. 8000 device family has a new debug engine that needs to be configured differently than 7000's. The debug engine's DMA works in chunks of memory and the size of the buffer really means the start of the last chunk. Since one chunk is 256-byte long, we should configure the device to write to buffer_size - 256. This fixes a situation were the device would write to memory it is not allowed to access. Signed-off-by:
-
Emmanuel Grumbach authored
commit a1cdb1c5 upstream. My commit below introduced a mutex in the transport to prevent concurrent operations. To do so, it added a flag (is_down) to make sure the transport is in the right state. This uncoverred an bug that didn't cause any harm until now: iwldvm calls stop_device and then starts the firmware without calling start_hw in between. While this flow is fine from the device configuration point of view (register, etc...), it is now forbidden by the new is_down flag. This led to this error to appear: iwlwifi 0000:05:00.0: Can't start_fw since the HW hasn't been started and the suspend would fail. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=109591Reported-by:
Bogdan Bogush <bogdan.s.bogush@gmail.com> Fixes=fa9f3281 ("iwlwifi: pcie: lock start_hw / start_fw / stop_device") Signed-off-by:
-
Jann Horn authored
commit 3dfb7d8c upstream. It looks like smack and yama weren't aware that the ptrace mode can have flags ORed into it - PTRACE_MODE_NOAUDIT until now, but only for /proc/$pid/stat, and with the PTRACE_MODE_*CREDS patch, all modes have flags ORed into them. Signed-off-by:
Jann Horn <jann@thejh.net> Acked-by:
Kees Cook <keescook@chromium.org> Acked-by:
Casey Schaufler <casey@schaufler-ca.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Morris <james.l.morris@oracle.com> Cc: "Serge E. Hallyn" <serge.hallyn@ubuntu.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Matan Barak authored
commit 64936773 upstream. cma_validate_port wrongly assumed that Ethernet devices are RoCE devices and thus their ndev should be matched in the GID table. This broke the iWarp support. Fixing that matching the ndev only if we work on a RoCE port. Cc: <stable@vger.kernel.org> # 4.4.x- Fixes: abae1b71 ('IB/cma: cma_validate_port should verify the port and netdevice') Reported-by:
Hariprasad Shenai <hariprasad@chelsio.com> Tested-by:
Matan Barak <matanb@mellanox.com> Reviewed-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Thomas Gleixner authored
commit 98229aa3 upstream. We still can end up with a stale vector due to the following: CPU0 CPU1 CPU2 lock_vector() data->move_in_progress=0 sendIPI() unlock_vector() set_affinity() assign_irq_vector() lock_vector() handle_IPI move_in_progress = 1 lock_vector() unlock_vector() move_in_progress == 1 So we need to serialize the vector assignment against a pending cleanup. The solution is rather simple now. We not only check for the move_in_progress flag in assign_irq_vector(), we also check whether there is still a cleanup pending in the old_domain cpumask. If so, we return -EBUSY to the caller and let him deal with it. Though we have to be careful in the cpu unplug case. If the cleanout has not yet completed then the following setaffinity() call would return -EBUSY. Add code which prevents this. Full context is here: http://lkml.kernel.org/r/5653B688.4050809@stratus.comReported-and-tested-by:
Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Tested-by:
Borislav Petkov <bp@alien8.de> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Jeremiah Mahler <jmmahler@gmail.com> Cc: andy.shevchenko@gmail.com Cc: Guenter Roeck <linux@roeck-us.net> Link: http://lkml.kernel.org/r/20151231160107.207265407@linutronix.deSigned-off-by:
-
Thomas Gleixner authored
commit 90a2282e upstream. First of all there is no point in looking up the irq descriptor again, but we also need the descriptor for the final cleanup race fix in the next patch. Make that change seperate. No functional difference. Signed-off-by:
-
Thomas Gleixner authored
commit 56d7d2f4 upstream. We want to synchronize new vector assignments with a pending cleanup. Remove a dying cpu from a pending cleanup mask. Signed-off-by:
-
Thomas Gleixner authored
commit 5da0c121 upstream. There is no need to allocate a new cpumask for sending the cleanup vector. The old_domain mask is now protected by the vector_lock, so we can safely remove the offline cpus from it and send the IPI with the resulting mask. Signed-off-by:
-
Thomas Gleixner authored
commit c1684f50 upstream. send_cleanup_vector() fiddles with the old_domain mask unprotected because it relies on the protection by the move_in_progress flag. But this is fatal, as the flag is reset after the IPI has been sent. So a cpu which receives the IPI can still see the flag set and therefor ignores the cleanup request. If no other cleanup request happens then the vector stays stale on that cpu and in case of an irq removal the vector still persists. That can lead to use after free when the next cleanup IPI happens. Protect the code with vector_lock and clear move_in_progress before sending the IPI. This does not plug the race which Joe reported because: CPU0 CPU1 CPU2 lock_vector() data->move_in_progress=0 sendIPI() unlock_vector() set_affinity() assign_irq_vector() lock_vector() handle_IPI move_in_progress = 1 lock_vector() unlock_vector() move_in_progress == 1 The full fix comes with a later patch. Reported-and-tested-by:
-
