- 28 Nov, 2016 36 commits
-
-
Myron Stowe authored
commit 06cf35f9 upstream. Some AMD CS553x devices have read-only BARs because of a firmware or hardware defect. There's a workaround in quirk_cs5536_vsa(), but it no longer works after 36e81648 ("PCI: Restore detection of read-only BARs"). Prior to 36e81648, we filled in res->start; afterwards we leave it zeroed out. The quirk only updated the size, so the driver tried to use a region starting at zero, which didn't work. Expand quirk_cs5536_vsa() to read the base addresses from the BARs and hard-code the sizes. On Nix's system BAR 2's read-only value is 0x6200. Prior to 36e81648, we interpret that as a 512-byte BAR based on the lowest-order bit set. Per datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to avoid clearing any address bits if a platform uses only 64-byte alignment. [js] pcibios_bus_to_resource takes pdev, not bus in 3.12 [bhelgaas: changelog, reduce BAR 2 size to 64] Fixes: 36e81648 ("PCI: Restore detection of read-only BARs") Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4 Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdfReported-and-tested-by:
Nix <nix@esperi.org.uk> Signed-off-by:
Myron Stowe <myron.stowe@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Peter Zijlstra authored
commit c3c87e77 upstream. The fix from 9fc81d87 ("perf: Fix events installation during moving group") was incomplete in that it failed to recognise that creating a group with events for different CPUs is semantically broken -- they cannot be co-scheduled. Furthermore, it leads to real breakage where, when we create an event for CPU Y and then migrate it to form a group on CPU X, the code gets confused where the counter is programmed -- triggered in practice as well by me via the perf fuzzer. Fix this by tightening the rules for creating groups. Only allow grouping of counters that can be co-scheduled in the same context. This means for the same task and/or the same cpu. Fixes: 9fc81d87 ("perf: Fix events installation during moving group") Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/20150123125834.090683288@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 1eec34e9 upstream. There is a poll loop for max 25us for HS devices. Now guess what, I tested it in gadget mode and forgot about the little detail. Nobody seem to have it noticed… This patch adds the missing logic for hostmode so it is recognized in host and device mode properly. Fixes: 50aea6fc ("usb: musb: cppi41: fire hrtimer according to programmed channel length") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Ben Hutchings authored
commit 3d0ad094 upstream. IPv6 does not allow fragmentation by routers, so there is no fragmentation ID in the fixed header. UFO for IPv6 requires the ID to be passed separately, but there is no provision for this in the virtio net protocol. Until recently our software implementation of UFO/IPv6 generated a new ID, but this was a bug. Now we will use ID=0 for any UFO/IPv6 packet passed through a tap, which is even worse. Unfortunately there is no distinction between UFO/IPv4 and v6 features, so disable UFO on taps and virtio_net completely until we have a proper solution. We cannot depend on VM managers respecting the tap feature flags, so keep accepting UFO packets but log a warning the first time we do this. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf4 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Ard Biesheuvel authored
commit 85c8555f upstream. Read-only memory ranges may be backed by the zero page, so avoid misidentifying it a a MMIO pfn. This fixes another issue I identified when testing QEMU+KVM_UEFI, where a read to an uninitialized emulated NOR flash brought in the zero page, but mapped as a read-write device region, because kvm_is_mmio_pfn() misidentifies it as a MMIO pfn due to its PG_reserved bit being set. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Fixes: b8865767 ("ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping") Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Ard Biesheuvel authored
commit 0b70068e upstream. In order to make the static inline function is_zero_pfn() callable by modules, export its symbol dependencies 'zero_pfn' and (for s390 and mips) 'zero_page_mask'. We need this for KVM, as CONFIG_KVM is a tristate for all supported architectures except ARM and arm64, and testing a pfn whether it refers to the zero page is required to correctly distinguish the zero page from other special RAM ranges that may also have the PG_reserved bit set, but need to be treated as MMIO memory. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Johannes Weiner authored
commit 139b6a6f upstream. Dave Jones reports the following crash when find_get_pages_tag() runs into an exceptional entry: kernel BUG at mm/filemap.c:1347! RIP: find_get_pages_tag+0x1cb/0x220 Call Trace: find_get_pages_tag+0x36/0x220 pagevec_lookup_tag+0x21/0x30 filemap_fdatawait_range+0xbe/0x1e0 filemap_fdatawait+0x27/0x30 sync_inodes_sb+0x204/0x2a0 sync_inodes_one_sb+0x19/0x20 iterate_supers+0xb2/0x110 sys_sync+0x44/0xb0 ia32_do_call+0x13/0x13 1343 /* 1344 * This function is never used on a shmem/tmpfs 1345 * mapping, so a swap entry won't be found here. 1346 */ 1347 BUG(); After commit 0cd6144a ("mm + fs: prepare for non-page entries in page cache radix trees") this comment and BUG() are out of date because exceptional entries can now appear in all mappings - as shadows of recently evicted pages. However, as Hugh Dickins notes, "it is truly surprising for a PAGECACHE_TAG_WRITEBACK (and probably any other PAGECACHE_TAG_*) to appear on an exceptional entry. I expect it comes down to an occasional race in RCU lookup of the radix_tree: lacking absolute synchronization, we might sometimes catch an exceptional entry, with the tag which really belongs with the unexceptional entry which was there an instant before." And indeed, not only is the tree walk lockless, the tags are also read in chunks, one radix tree node at a time. There is plenty of time for page reclaim to swoop in and replace a page that was already looked up as tagged with a shadow entry. Remove the BUG() and update the comment. While reviewing all other lookup sites for whether they properly deal with shadow entries of evicted pages, update all the comments and fix memcg file charge moving to not miss shmem/tmpfs swapcache pages. Fixes: 0cd6144a ("mm + fs: prepare for non-page entries in page cache radix trees") Signed-off-by:
Johannes Weiner <hannes@cmpxchg.org> Reported-by:
Dave Jones <davej@redhat.com> Acked-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
David S. Miller authored
[ Upstream commit a74ad5e6 ] When the vmalloc area gets fragmented, and because the firmware mapping area sits between where modules live and the vmalloc area, we can sometimes receive requests for enormous kernel TLB range flushes. When this happens the cpu just spins flushing billions of pages and this triggers the NMI watchdog and other problems. We took care of this on the TSB side by doing a linear scan of the table once we pass a certain threshold. Do something similar for the TLB flush, however we are limited by the TLB flush facilities provided by the different chip variants. First of all we use an (mostly arbitrary) cut-off of 256K which is about 32 pages. This can be tuned in the future. The huge range code path for each chip works as follows: 1) On spitfire we flush all non-locked TLB entries using diagnostic acceses. 2) On cheetah we use the "flush all" TLB flush. 3) On sun4v/hypervisor we do a TLB context flush on context 0, which unlike previous chips does not remove "permanent" or locked entries. We could probably do something better on spitfire, such as limiting the flush to kernel TLB entries or even doing range comparisons. However that probably isn't worth it since those chips are old and the TLB only had 64 entries. Reported-by:
James Clarke <jrtc27@jrtc27.com> Tested-by:
-
David S. Miller authored
[ Upstream commit a236441b ] Just like the non-cross-call TLB flush handlers, the cross-call ones need to avoid doing PC-relative branches outside of their code blocks. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 830cda3f ] Noticed by James Clarke. Signed-off-by:
-
David S. Miller authored
[ Upstream commit b429ae4d ] When we copy code over to patch another piece of code, we can only use PC-relative branches that target code within that piece of code. Such PC-relative branches cannot be made to external symbols because the patch moves the location of the code and thus modifies the relative address of external symbols. Use an absolute jmpl to fix this problem. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 849c4987 ] If the number of pages we are flushing is more than twice the number of entries in the TSB, just scan the TSB table for matches rather than probing each and every page in the range. Based upon a patch and report by James Clarke. Signed-off-by:
-
James Clarke authored
[ Upstream commit 9d9fa230 ] Additionally, if the offset will overflow the immediate for a ba,pt instruction, fall back on a standard ba to get an extra 3 bits. Signed-off-by:
-
Mike Kravetz authored
[ Upstream commit af1b1a9b ] do_sparc64_fault() calculates both the base and huge page RSS sizes and uses this information in calls to tsb_grow(). The calculation for base page TSB size is not correct if the task uses hugetlb pages. hugetlb pages are not accounted for in RSS, therefore the call to get_mm_rss(mm) does not include hugetlb pages. However, the number of pages based on huge_pte_count (which does include hugetlb pages) is subtracted from this value. This will result in an artificially small and often negative RSS calculation. The base TSB size is then often set to max_tsb_size as the passed RSS is unsigned, so a negative value looks really big. THP pages are also accounted for in huge_pte_count, and THP pages are accounted for in RSS so the calculation in do_sparc64_fault() is correct if a task only uses THP pages. A single huge_pte_count is not sufficient for TSB sizing if both hugetlb and THP pages can be used. Instead of a single counter, use two: one for hugetlb and one for THP. Signed-off-by:
Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 4f6deb8c ] On pre-Niagara systems, we fetch the fault address on data TLB exceptions from the TLB_TAG_ACCESS register. But this register also contains the context ID assosciated with the fault in the low 13 bits of the register value. This propagates into current_thread_info()->fault_address and can cause trouble later on. So clear the low 13-bits out of the TLB_TAG_ACCESS value in the cases where it matters. Reported-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ac6e7800 ] With syzkaller help, Marco Grassi found a bug in TCP stack, crashing in tcp_collapse() Root cause is that sk_filter() can truncate the incoming skb, but TCP stack was not really expecting this to happen. It probably was expecting a simple DROP or ACCEPT behavior. We first need to make sure no part of TCP header could be removed. Then we need to adjust TCP_SKB_CB(skb)->end_seq Many thanks to syzkaller team and Marco for giving us a reproducer. Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Marco Grassi <marco.gra@gmail.com> Reported-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
-
Stephen Suryaputra Lin authored
[ Upstream commit 969447f2 ] In v2.6, ip_rt_redirect() calls arp_bind_neighbour() which returns 0 and then the state of the neigh for the new_gw is checked. If the state isn't valid then the redirected route is deleted. This behavior is maintained up to v3.5.7 by check_peer_redirect() because rt->rt_gateway is assigned to peer->redirect_learned.a4 before calling ipv4_neigh_lookup(). After commit 5943634f ("ipv4: Maintain redirect and PMTU info in struct rtable again."), ipv4_neigh_lookup() is performed without the rt_gateway assigned to the new_gw. In the case when rt_gateway (old_gw) isn't zero, the function uses it as the key. The neigh is most likely valid since the old_gw is the one that sends the ICMP redirect message. Then the new_gw is assigned to fib_nh_exception. The problem is: the new_gw ARP may never gets resolved and the traffic is blackholed. So, use the new_gw for neigh lookup. Changes from v1: - use __ipv4_neigh_lookup instead (per Eric Dumazet). Fixes: 5943634f ("ipv4: Maintain redirect and PMTU info in struct rtable again.") Signed-off-by:
Stephen Suryaputra Lin <ssurya@ieee.org> Signed-off-by:
-
WANG Cong authored
commit 2c1a4311 upstream. Fixes: commit f187bc6e ("ipv4: No need to set generic neighbour pointer") Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 7233bc84 ] sctp_wait_for_connect() currently already holds the asoc to keep it alive during the sleep, in case another thread release it. But Andrey Konovalov and Dmitry Vyukov reported an use-after-free in such situation. Problem is that __sctp_connect() doesn't get a ref on the asoc and will do a read on the asoc after calling sctp_wait_for_connect(), but by then another thread may have closed it and the _put on sctp_wait_for_connect will actually release it, causing the use-after-free. Fix is, instead of doing the read after waiting for the connect, do it before so, and avoid this issue as the socket is still locked by then. There should be no issue on returning the asoc id in case of failure as the application shouldn't trust on that number in such situations anyway. This issue doesn't exist in sctp_sendmsg() path. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Reported-by:
Andrey Konovalov <andreyknvl@google.com> Tested-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 990ff4d8 ] While fuzzing kernel with syzkaller, Andrey reported a nasty crash in inet6_bind() caused by DCCP lacking a required method. Fixes: ab1e0a13 ("[SOCK] proto: Add hashinfo member to struct proto") Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 1aa9d1a0 ] dccp_v6_err() does not use pskb_may_pull() and might access garbage. We only need 4 bytes at the beginning of the DCCP header, like TCP, so the 8 bytes pulled in icmpv6_notify() are more than enough. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 6706a97f ] dccp_v4_err() does not use pskb_may_pull() and might access garbage. We only need 4 bytes at the beginning of the DCCP header, like TCP, so the 8 bytes pulled in icmp_socket_deliver() are more than enough. This patch might allow to process more ICMP messages, as some routers are still limiting the size of reflected bytes to 28 (RFC 792), instead of extended lengths (RFC 1812 4.3.2.3) Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 346da62c ] Andrey reported following warning while fuzzing with syzkaller WARNING: CPU: 1 PID: 21072 at net/dccp/proto.c:83 dccp_set_state+0x229/0x290 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 21072 Comm: syz-executor Not tainted 4.9.0-rc1+ #293 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff88003d4c7738 ffffffff81b474f4 0000000000000003 dffffc0000000000 ffffffff844f8b00 ffff88003d4c7804 ffff88003d4c7800 ffffffff8140c06a 0000000041b58ab3 ffffffff8479ab7d ffffffff8140beae ffffffff8140cd00 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81b474f4>] dump_stack+0xb3/0x10f lib/dump_stack.c:51 [<ffffffff8140c06a>] panic+0x1bc/0x39d kernel/panic.c:179 [<ffffffff8111125c>] __warn+0x1cc/0x1f0 kernel/panic.c:542 [<ffffffff8111144c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585 [<ffffffff8389e5d9>] dccp_set_state+0x229/0x290 net/dccp/proto.c:83 [<ffffffff838a0aa2>] dccp_close+0x612/0xc10 net/dccp/proto.c:1016 [<ffffffff8316bf1f>] inet_release+0xef/0x1c0 net/ipv4/af_inet.c:415 [<ffffffff82b6e89e>] sock_release+0x8e/0x1d0 net/socket.c:570 [<ffffffff82b6e9f6>] sock_close+0x16/0x20 net/socket.c:1017 [<ffffffff815256ad>] __fput+0x29d/0x720 fs/file_table.c:208 [<ffffffff81525bb5>] ____fput+0x15/0x20 fs/file_table.c:244 [<ffffffff811727d8>] task_work_run+0xf8/0x170 kernel/task_work.c:116 [< inline >] exit_task_work include/linux/task_work.h:21 [<ffffffff8111bc53>] do_exit+0x883/0x2ac0 kernel/exit.c:828 [<ffffffff811221fe>] do_group_exit+0x10e/0x340 kernel/exit.c:931 [<ffffffff81143c94>] get_signal+0x634/0x15a0 kernel/signal.c:2307 [<ffffffff81054aad>] do_signal+0x8d/0x1a30 arch/x86/kernel/signal.c:807 [<ffffffff81003a05>] exit_to_usermode_loop+0xe5/0x130 arch/x86/entry/common.c:156 [< inline >] prepare_exit_to_usermode arch/x86/entry/common.c:190 [<ffffffff81006298>] syscall_return_slowpath+0x1a8/0x1e0 arch/x86/entry/common.c:259 [<ffffffff83fc1a62>] entry_SYSCALL_64_fastpath+0xc0/0xc2 Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: disabled Fix this the same way we did for TCP in commit 565b7b2d ("tcp: do not send reset to already closed sockets") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ac9e70b1 ] Imagine initial value of max_skb_frags is 17, and last skb in write queue has 15 frags. Then max_skb_frags is lowered to 14 or smaller value. tcp_sendmsg() will then be allowed to add additional page frags and eventually go past MAX_SKB_FRAGS, overflowing struct skb_shared_info. Fixes: 5f74f82e ("net:Add sysctl_max_skb_frags") Signed-off-by:
-
Eli Cooper authored
[ Upstream commit 23f4ffed ] skb->cb may contain data from previous layers. In the observed scenario, the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so that small packets sent through the tunnel are mistakenly fragmented. This patch unconditionally clears the control buffer in ip6tunnel_xmit(), which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier. Cc: stable@vger.kernel.org Signed-off-by:
Eli Cooper <elicooper@gmx.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 4f2e4ad5 ] Sending zero checksum is ok for TCP, but not for UDP. UDPv6 receiver should by default drop a frame with a 0 checksum, and UDPv4 would not verify the checksum and might accept a corrupted packet. Simply replace such checksum by 0xffff, regardless of transport. This error was caught on SIT tunnels, but seems generic. Signed-off-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit e551c32d ] At accept() time, it is possible the parent has a non zero sk_err_soft, leftover from a prior error. Make sure we do not leave this value in the child, as it makes future getsockopt(SO_ERROR) calls quite unreliable. Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Joe Perches authored
commit 8c7fbe57 upstream. Commit 38764884 ("include/stddef.h: Move offsetofend() from vfio.h to a generic kernel header") added offsetofend outside the normal include #ifndef/#endif guard. Move it inside. Miscellanea: o remove unnecessary blank line o standardize offsetof macros whitespace style Signed-off-by:
Joe Perches <joe@perches.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Signed-off-by:
-
Denys Vlasenko authored
commit 38764884 upstream. Suggested by Andy. Suggested-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Denys Vlasenko <dvlasenk@redhat.com> Acked-by:
-
Gavin Shan authored
commit b13460b9 upstream. The macro offsetofend() introduces unnecessary temporary variable "tmp". The patch avoids that and saves a bit memory in stack. Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit bf911e98 ] Andrey Konovalov reported that KASAN detected that SCTP was using a slab beyond the boundaries. It was caused because when handling out of the blue packets in function sctp_sf_ootb() it was checking the chunk len only after already processing the first chunk, validating only for the 2nd and subsequent ones. The fix is to just move the check upwards so it's also validated for the 1st chunk. Reported-by:
-
Jiri Slaby authored
[ Upstream commit a4b8e71b ] Most of getsockopt handlers in net/sctp/socket.c check len against sizeof some structure like: if (len < sizeof(int)) return -EINVAL; On the first look, the check seems to be correct. But since len is int and sizeof returns size_t, int gets promoted to unsigned size_t too. So the test returns false for negative lengths. Yes, (-1 < sizeof(long)) is false. Fix this in sctp by explicitly checking len < 0 before any getsockopt handler is called. Note that sctp_getsockopt_events already handled the negative case. Since we added the < 0 check elsewhere, this one can be removed. If not checked, this is the result: UBSAN: Undefined behaviour in ../mm/page_alloc.c:2722:19 shift exponent 52 is too large for 32-bit type 'int' CPU: 1 PID: 24535 Comm: syz-executor Not tainted 4.8.1-0-syzkaller #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014 0000000000000000 ffff88006d99f2a8 ffffffffb2f7bdea 0000000041b58ab3 ffffffffb4363c14 ffffffffb2f7bcde ffff88006d99f2d0 ffff88006d99f270 0000000000000000 0000000000000000 0000000000000034 ffffffffb5096422 Call Trace: [<ffffffffb3051498>] ? __ubsan_handle_shift_out_of_bounds+0x29c/0x300 ... [<ffffffffb273f0e4>] ? kmalloc_order+0x24/0x90 [<ffffffffb27416a4>] ? kmalloc_order_trace+0x24/0x220 [<ffffffffb2819a30>] ? __kmalloc+0x330/0x540 [<ffffffffc18c25f4>] ? sctp_getsockopt_local_addrs+0x174/0xca0 [sctp] [<ffffffffc18d2bcd>] ? sctp_getsockopt+0x10d/0x1b0 [sctp] [<ffffffffb37c1219>] ? sock_common_getsockopt+0xb9/0x150 [<ffffffffb37be2f5>] ? SyS_getsockopt+0x1a5/0x270 Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 7cb3f921 ] Satish reported a problem with the perm multicast router ports not getting reenabled after some series of events, in particular if it happens that the multicast snooping has been disabled and the port goes to disabled state then it will be deleted from the router port list, but if it moves into non-disabled state it will not be re-added because the mcast snooping is still disabled, and enabling snooping later does nothing. Here are the steps to reproduce, setup br0 with snooping enabled and eth1 added as a perm router (multicast_router = 2): 1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping 2. $ ip l set eth1 down ^ This step deletes the interface from the router list 3. $ ip l set eth1 up ^ This step does not add it again because mcast snooping is disabled 4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping 5. $ bridge -d -s mdb show <empty> At this point we have mcast enabled and eth1 as a perm router (value = 2) but it is not in the router list which is incorrect. After this change: 1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping 2. $ ip l set eth1 down ^ This step deletes the interface from the router list 3. $ ip l set eth1 up ^ This step does not add it again because mcast snooping is disabled 4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping 5. $ bridge -d -s mdb show router ports on br0: eth1 Note: we can directly do br_multicast_enable_port for all because the querier timer already has checks for the port state and will simply expire if it's in blocking/disabled. See the comment added by commit 9aa66382 ("bridge: multicast: add a comment to br_port_state_selection about blocking state") Fixes: 561f1103 ("bridge: Add multicast_snooping sysfs toggle") Reported-by:
Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit a220445f ] The goal of the patch is to fix this scenario: ip link add dummy1 type dummy ip link set dummy1 up ip link set lo down ; ip link set lo up After that sequence, the local route to the link layer address of dummy1 is not there anymore. When the loopback is set down, all local routes are deleted by addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still exists, because the corresponding idev has a reference on it. After the rcu grace period, dst_rcu_free() is called, and thus ___dst_free(), which will set obsolete to DST_OBSOLETE_DEAD. In this case, init_loopback() is called before dst_rcu_free(), thus obsolete is still sets to something <= 0. So, the function doesn't add the route again. To avoid that race, let's check the rt6 refcnt instead. Fixes: 25fb6ca4 ("net IPv6 : Fix broken IPv6 routing table after loopback down-up") Fixes: a881ae1f ("ipv6: don't call addrconf_dst_alloc again when enable lo") Fixes: 33d99113 ("ipv6: reallocate addrconf router for ipv6 address when lo device up") Reported-by:
Francesco Santoro <francesco.santoro@6wind.com> Reported-by:
Samuel Gauthier <samuel.gauthier@6wind.com> CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Weilong Chen <chenweilong@huawei.com> CC: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Anoob Soman authored
[ Upstream commit 66644982 ] If a socket has FANOUT sockopt set, a new proto_hook is registered as part of fanout_add(). When processing a NETDEV_UNREGISTER event in af_packet, __fanout_unlink is called for all sockets, but prot_hook which was registered as part of fanout_add is not removed. Call fanout_release, on a NETDEV_UNREGISTER, which removes prot_hook and removes fanout from the fanout_list. This fixes BUG_ON(!list_empty(&dev->ptype_specific)) in netdev_run_todo() Signed-off-by:
Anoob Soman <anoob.soman@citrix.com> Signed-off-by:
-
Andrew Collins authored
[ Upstream commit 93409033 ] This is a respin of a patch to fix a relatively easily reproducible kernel panic related to the all_adj_list handling for netdevs in recent kernels. The following sequence of commands will reproduce the issue: ip link add link eth0 name eth0.100 type vlan id 100 ip link add link eth0 name eth0.200 type vlan id 200 ip link add name testbr type bridge ip link set eth0.100 master testbr ip link set eth0.200 master testbr ip link add link testbr mac0 type macvlan ip link delete dev testbr This creates an upper/lower tree of (excuse the poor ASCII art): /---eth0.100-eth0 mac0-testbr- \---eth0.200-eth0 When testbr is deleted, the all_adj_lists are walked, and eth0 is deleted twice from the mac0 list. Unfortunately, during setup in __netdev_upper_dev_link, only one reference to eth0 is added, so this results in a panic. This change adds reference count propagation so things are handled properly. Matthias Schiffer reported a similar crash in batman-adv: https://github.com/freifunk-gluon/gluon/issues/680 https://www.open-mesh.org/issues/247 which this patch also seems to resolve. [js] 3.12 does not have lists yet. Signed-off-by:
Andrew Collins <acollins@cradlepoint.com> Signed-off-by:
-
- 24 Nov, 2016 4 commits
-
-
Nikolay Aleksandrov authored
[ Upstream commit 2cf75070 ] Since the commit below the ipmr/ip6mr rtnl_unicast() code uses the portid instead of the previous dst_pid which was copied from in_skb's portid. Since the skb is new the portid is 0 at that point so the packets are sent to the kernel and we get scheduling while atomic or a deadlock (depending on where it happens) by trying to acquire rtnl two times. Also since this is RTM_GETROUTE, it can be triggered by a normal user. Here's the sleeping while atomic trace: [ 7858.212557] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620 [ 7858.212748] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0 [ 7858.212881] 2 locks held by swapper/0/0: [ 7858.213013] #0: (((&mrt->ipmr_expire_timer))){+.-...}, at: [<ffffffff810fbbf5>] call_timer_fn+0x5/0x350 [ 7858.213422] #1: (mfc_unres_lock){+.....}, at: [<ffffffff8161e005>] ipmr_expire_process+0x25/0x130 [ 7858.213807] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.0-rc7+ #179 [ 7858.213934] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014 [ 7858.214108] 0000000000000000 ffff88005b403c50 ffffffff813a7804 0000000000000000 [ 7858.214412] ffffffff81a1338e ffff88005b403c78 ffffffff810a4a72 ffffffff81a1338e [ 7858.214716] 000000000000026c 0000000000000000 ffff88005b403ca8 ffffffff810a4b9f [ 7858.215251] Call Trace: [ 7858.215412] <IRQ> [<ffffffff813a7804>] dump_stack+0x85/0xc1 [ 7858.215662] [<ffffffff810a4a72>] ___might_sleep+0x192/0x250 [ 7858.215868] [<ffffffff810a4b9f>] __might_sleep+0x6f/0x100 [ 7858.216072] [<ffffffff8165bea3>] mutex_lock_nested+0x33/0x4d0 [ 7858.216279] [<ffffffff815a7a5f>] ? netlink_lookup+0x25f/0x460 [ 7858.216487] [<ffffffff8157474b>] rtnetlink_rcv+0x1b/0x40 [ 7858.216687] [<ffffffff815a9a0c>] netlink_unicast+0x19c/0x260 [ 7858.216900] [<ffffffff81573c70>] rtnl_unicast+0x20/0x30 [ 7858.217128] [<ffffffff8161cd39>] ipmr_destroy_unres+0xa9/0xf0 [ 7858.217351] [<ffffffff8161e06f>] ipmr_expire_process+0x8f/0x130 [ 7858.217581] [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180 [ 7858.217785] [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180 [ 7858.217990] [<ffffffff810fbc95>] call_timer_fn+0xa5/0x350 [ 7858.218192] [<ffffffff810fbbf5>] ? call_timer_fn+0x5/0x350 [ 7858.218415] [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180 [ 7858.218656] [<ffffffff810fde10>] run_timer_softirq+0x260/0x640 [ 7858.218865] [<ffffffff8166379b>] ? __do_softirq+0xbb/0x54f [ 7858.219068] [<ffffffff816637c8>] __do_softirq+0xe8/0x54f [ 7858.219269] [<ffffffff8107a948>] irq_exit+0xb8/0xc0 [ 7858.219463] [<ffffffff81663452>] smp_apic_timer_interrupt+0x42/0x50 [ 7858.219678] [<ffffffff816625bc>] apic_timer_interrupt+0x8c/0xa0 [ 7858.219897] <EOI> [<ffffffff81055f16>] ? native_safe_halt+0x6/0x10 [ 7858.220165] [<ffffffff810d64dd>] ? trace_hardirqs_on+0xd/0x10 [ 7858.220373] [<ffffffff810298e3>] default_idle+0x23/0x190 [ 7858.220574] [<ffffffff8102a20f>] arch_cpu_idle+0xf/0x20 [ 7858.220790] [<ffffffff810c9f8c>] default_idle_call+0x4c/0x60 [ 7858.221016] [<ffffffff810ca33b>] cpu_startup_entry+0x39b/0x4d0 [ 7858.221257] [<ffffffff8164f995>] rest_init+0x135/0x140 [ 7858.221469] [<ffffffff81f83014>] start_kernel+0x50e/0x51b [ 7858.221670] [<ffffffff81f82120>] ? early_idt_handler_array+0x120/0x120 [ 7858.221894] [<ffffffff81f8243f>] x86_64_start_reservations+0x2a/0x2c [ 7858.222113] [<ffffffff81f8257c>] x86_64_start_kernel+0x13b/0x14a Fixes: 2942e900 ("[RTNETLINK]: Use rtnl_unicast() for rtnetlink unicasts") Signed-off-by:
-
Lance Richardson authored
[ Upstream commit db32e4e4 ] Similar to commit 3be07244 ("ip6_gre: fix flowi6_proto value in xmit path"), set flowi6_proto to IPPROTO_GRE for output route lookup. Up until now, ip6gre_xmit_other() has set flowi6_proto to a bogus value. This affected output route lookup for packets sent on an ip6gretap device in cases where routing was dependent on the value of flowi6_proto. Since the correct proto is already set in the tunnel flowi6 template via commit 252f3f5a ("ip6_gre: Set flowi6_proto as IPPROTO_GRE in xmit path."), simply delete the line setting the incorrect flowi6_proto value. Suggested-by:
Jiri Benc <jbenc@redhat.com> Fixes: c12b395a ("gre: Support GRE over IPv6") Reviewed-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by:
Lance Richardson <lrichard@redhat.com> Signed-off-by:
-
Douglas Caetano dos Santos authored
[ Upstream commit 2fe664f1 ] With TCP MTU probing enabled and offload TX checksumming disabled, tcp_mtu_probe() calculated the wrong checksum when a fragment being copied into the probe's SKB had an odd length. This was caused by the direct use of skb_copy_and_csum_bits() to calculate the checksum, as it pads the fragment being copied, if needed. When this fragment was not the last, a subsequent call used the previous checksum without considering this padding. The effect was a stale connection in one way, as even retransmissions wouldn't solve the problem, because the checksum was never recalculated for the full SKB length. Signed-off-by:
Douglas Caetano dos Santos <douglascs@taghos.com.br> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 20c64d5c ] A malicious TCP receiver, sending SACK, can force the sender to split skbs in write queue and increase its memory usage. Then, when socket is closed and its write queue purged, we might overflow sk_forward_alloc (It becomes negative) sk_mem_reclaim() does nothing in this case, and more than 2GB are leaked from TCP perspective (tcp_memory_allocated is not changed) Then warnings trigger from inet_sock_destruct() and sk_stream_kill_queues() seeing a not zero sk_forward_alloc All TCP stack can be stuck because TCP is under memory pressure. A simple fix is to preemptively reclaim from sk_mem_uncharge(). This makes sure a socket wont have more than 2 MB forward allocated, after burst and idle period. Signed-off-by:
-
