Pass the correct GPIO to gpio_free
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

this patch fix the following errors :
arch/arm/mach-mx3/mach-pcm037_eet.c:62: error: implicit declaration of function 'MXC_SPI_CS'
arch/arm/mach-mx3/mach-pcm037_eet.c:185: error: implicit declaration of function 'imx35_add_spi_imx0'

from the Kconfig pcm037 is i.MX31 based and not i.MX35 so replace
imx35_add_spi_imx0 by imx31_add_spi_imx0
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: remove unneeded #include <mach/spi.h>]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c26)]

As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

add NAND, SDHC
Signed-off-by: Eric Bénard <eric@eukrea.com>

Signed-off-by: Eric Bénard <eric@eukrea.com>

this patch really configure the GPIO in GPIO mode.
Signed-off-by: Eric Bénard <eric@eukrea.com>

Tested on i.MX25 and i.MX35 and i.MX51
Signed-off-by: Eric Bénard <eric@eukrea.com>

the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.

Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>

Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>

Signed-off-by: Eric Bénard <eric@eukrea.com>

Signed-off-by: Eric Bénard <eric@eukrea.com>

Signed-off-by: Eric Bénard <eric@eukrea.com>

the PHY is UTMI so don't create an ULPI viewpoint.
Signed-off-by: Eric Bénard <eric@eukrea.com>

Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: Eric Bénard <eric@eukrea.com>

this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
    error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
    error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID

* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: Eric Bénard <eric@eukrea.com>

During the reorganisation of the imx-i2c devices
(in 64de5ec1) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.

Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Ethernet hangs off OTG
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Get serial port working for now
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The i.MX51 ECSPI has a fifo size of 64 entries instead of 8 entries as
found on the other cspi bus devices.

Cc: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.

This fix should not hurt already working CPUs, as they are using the written
register value already.

Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.

While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This fixes

	arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
	arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used

when USB_ULPI is not selected.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on work done earlier by Sascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: actually squash the two approaches together]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Also, remove the deprecated symbols from arch/arm/mach-mx3/cpu.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

- remove functions which are no more necessary for tsc2007
- indent platform_data for better readability
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The first argument to I2C_BOARD_INFO is used to assign .type, so it should
not be specified a second time.

For the rtc-pcf8563/pcf8563 entry gcc preferred pcf8563, so did I.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This fixes the following sparse warning:

	arch/arm/mach-imx/pcm970-baseboard.c:224:13: warning: symbol 'pcm970_baseboard_init' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>