Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Useful for diagnostics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

So the code to suppress duplicate changes is effective.

Reported-by: Kyung Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.comyu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Provide robustness against low quality FLL sync clocks by increasing the
timeout for lock to an absurdly high point; we should never get anywhere
near hitting the timeout in a real system unless it is failing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The machine driver try to use GPIO15 of twl4030 for HS MUX which supposed to
select between TWL's HSOL/R and tlv320aic3254's HPL/R.
The TWL's GPIO allocated dynamically so the (OMAP_MAX_GPIO_LINES + 15) is no
longer valid GPIO number causing a kernel crash due to BUG_ON()
Also the current machine driver supports only TWL audio currently: there is
no need to control the GPIO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

For simplicity always run the DSP at the SYSCLK rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Turn off the ADSP memory when we aren't using it, saving a small amount of
power.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Specify overrun bit in interrupt mask
Add dmaengine specific routines
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[voice.shen@atmel.com: adapt to soc dmaengine framework]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch is split original atmel-pcm.c into new atmel-pcm.c and
atmel-pcm-pdc.c two files. The new atmel-pcm.c is the share routine
while will be used for pdc or dma transfer.

Using SND_ATMEL_SOC_PDC to select using PDC for audio transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some compiler versions complain.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Handle the jack detection inforamtion as bool from devicetree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'topic/adsp' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-arizona

devm_regmap_init_i2c() is device managed and makes error
handling and code cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some ADSP devices can make use of DVFS to optimise power consumption
depending on the operating frequency of the DSP core. Implement
support for this in the generic ADSP code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Both WM5102 and WM5110 support haptics, register the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Provide a haptics widget for use by the haptics driver and expose the DAPM
context for it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The Arizona CODECs contain a haptics module providing vibration feedback
support. Implement basic support for this, providing simple start/stop and
signal magnitude control.

Since the output path for haptics is routed through the CODEC audio routing
it is modelled as a signal generator within ASoC, the haptics driver calls
DAPM to start and stop the output drivers. An appropriate output path must
be configured via ALSA to connect the haptics source to the correct output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some other device functions need to integrate with signal sources in the
audio portion (primarily for haptics) so allow CODEC to export the DAPM
context by pointing to it from the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we skip reenables.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We cannot include any plat or mach headers for the multiplatform
support.

Fix the issue by defining local mcbsp_omap1().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Hi Mark,

thanks your insisting on a better description for the patch, I found a
more appropriate solution for the problem:

Compiling the SoC Audio driver for Freescale i.MX as a module
(CONFIG_SND_SOC_IMX_PCM=m) results in a non-functional sound driver
indicated by the error message:
| imx-sgtl5000 sound.1: platform imx-pcm-audio not registered
| imx-sgtl5000 sound.1: snd_soc_register_card failed (-517)
| platform sound.1: Driver imx-sgtl5000 requests probe deferral
instead of the message:
| imx-sgtl5000 sound.1:  sgtl5000 <-> 63fcc000.ssi mapping ok
that is to be expected upon loading the snd-soc-imx-pcm.ko module.

The build log reveals, that the file imx-pcm-dma.o (or imx-pcm-fiq.o
depending on the kernel configuration), which should be linked
together with imx-pcm.o into snd-imx-pcm.ko, is not being compiled in
this case.

The make rules for these files shows that the target object imx-pcm.o
is assigned to the variable snd-soc-imx-pcm-y while
imx-pcm-{dma,fiq}.o are added to to
snd-soc-imx-pcm-$(CONFIG_SND_SOC_IMX_PCM_DMA) and
snd-soc-imx-pcm-$(CONFIG_SND_SOC_IMX_PCM_FIQ) which resolve to
snd-soc-imx-pcm-m in this case.

According to Documentation/kbuild/modules.txt:
|When the module is built from multiple sources, an additional line is
|needed listing the files:
|
|        <module_name>-y := <src1>.o <src2>.o ...
Thus the type of the config variables CONFIG_SND_SOC_IMX_PCM_DMA and
CONFIG_SND_SOC_IMX_PCM_FIQ should be 'bool' instead of 'tristate' to
resolve to 'y' when selected.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>