Program trap handler settings to enable CWSR with software scheduler
on Aldebaran and Arcturus.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Amber Lin <Amber.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch limits the ref_div_max value to 100, during the
calculation of PLL feedback reference divider. With current
value (128), the produced fb_ref_div value generates unstable
output at particular frequencies. Radeon driver limits this
value at 100.

On Oland, when we try to setup mode 2048x1280@60 (a bit weird,
I know), it demands a clock of 221270 Khz. It's been observed
that the PLL calculations using values 128 and 100 are vastly
different, and look like this:

+------------------------------------------+
|Parameter    |AMDGPU        |Radeon       |
|             |              |             |
+-------------+----------------------------+
|Clock feedback              |             |
|divider max  |  128         |   100       |
|cap value    |              |             |
|             |              |             |
|             |              |             |
+------------------------------------------+
|ref_div_max  |              |             |
|             |  42          |  20         |
|             |              |             |
|             |              |             |
+------------------------------------------+
|ref_div      |  42          |  20         |
|             |              |             |
+------------------------------------------+
|fb_div       |  10326       |  8195       |
+------------------------------------------+
|fb_div       |  1024        |  163        |
+------------------------------------------+
|fb_dev_p     |  4           |  9          |
|frac fb_de^_p|              |             |
+----------------------------+-------------+

With ref_div_max value clipped at 100, AMDGPU driver can also
drive videmode 2048x1280@60 (221Mhz) and produce proper output
without any blanking and distortion on the screen.

PS: This value was changed from 128 to 100 in Radeon driver also, here:
https://github.com/freedesktop/drm-tip/commit/4b21ce1b4b5d262e7d4656b8ececc891fc3cb806

V1:
Got acks from:
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>

V2:
- Restricting the changes only for OLAND, just to avoid any regression
  for other cards.
- Changed unsigned -> unsigned int to make checkpatch quiet.

V3: Apply the change on SI family (not only oland) (Christian)

Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Eddy Qin <Eddy.Qin@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
A cleaner solution, only done once on boot.

[How]
Remove previous workaround and configure an extra
vmid one time on boot
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

schedule_delayed_work does not push back the work if it was already
scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms
after the first time GFXOFF was disabled and re-enabled, even if GFXOFF
was disabled and re-enabled again during those 100 ms.

This resulted in frame drops / stutter with the upcoming mutter 41
release on Navi 14, due to constantly enabling GFXOFF in the HW and
disabling it again (for getting the GPU clock counter).

To fix this, call cancel_delayed_work_sync when the disable count
transitions from 0 to 1, and only schedule the delayed work on the
reverse transition, not if the disable count was already 0. This makes
sure the delayed work doesn't run at unexpected times, and allows it to
be lock-free.

v2:
* Use cancel_delayed_work_sync & mutex_trylock instead of
  mod_delayed_work.
v3:
* Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König)
v4:
* Fix race condition between amdgpu_gfx_off_ctrl incrementing
  adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off
  checking for it to be 0 (Evan Quan)

Cc: stable@vger.kernel.org
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> # v3
Acked-by: Christian König <christian.koenig@amd.com> # v3
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For some reason we run into an use case where a BO is already pinned
into GTT, but should be pinned into VRAM|GTT again.

Handle that case gracefully as well.
Reviewed-by: Shashank Sharma <Shashank.sharma@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Considering Arcturus is a dedicated ASIC for computing, it
will be more proper to drop the support for fan speed reading
and setting. That's on the TODO list.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-by: Rui Teng <rui.teng@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Commit 04ed8459 ("drm/amdgpu: remove chash") removes the chash
architecture and its corresponding config CHASH.

There is still a reference to CHASH in the config DRM_AMDGPU in
./drivers/gpu/drm/Kconfig.

Remove this obsolete reference to config CHASH.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In some cases when we unload driver, warning call trace
will show up in vram_mgr_fini which claims that LRU is not empty, caused
by the ttm bo inside delay deleted queue.

[How]
We should flush delayed work to make sure the delay deleting is done.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

aldebaran supports up to 16 xgmi physical nodes.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We have a S3 issue on that SKU with BACO enabled. Will bring back this
when that root caused.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
dcn301_calculate_wm_and_dl() causes flickering when external monitor is
connected.

This issue has been fixed before by commit 0e4c0ae5
("drm/amdgpu/display: drop dcn301_calculate_wm_and_dl for now"), however
part of the fix was gone after commit 2cbcb78c ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next").

[how]
Use dcn30_calculate_wm_and_dlg() instead as in the original fix.

Fixes: 2cbcb78c ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

MMSCH 1.0 doesn't have major/minor version, only verison.
Signed-off-by: Zhigang Luo <zhigang.luo@amd.com>
Reviewed by Shaoyun.liu <Shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The TA has a limit to the amount of data that can be retrieved from
GET_TOPOLOGY.  For setups that exceed this limit, the xGMI topology
needs to be re-initialized and data needs to be re-fetched from the
extended link records by setting a flag in the shared command buffer.

The number of hops and the number of links must be accumulated by the
driver. Other data points are all fetched from the first request.
Because the TA has already exceeded its link record limit, it
cannot hold bidirectional information.  Otherwise the driver would
have to do more than two fetches so the driver has to reflect the
topology information in the opposite direction.

v2: squashed with internal reviewed fix
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Hawking Zhang <hawking.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Clang + -Wimplicit-fallthrough warns:

drivers/gpu/drm/radeon/radeon_fb.c:170:2: warning: unannotated
fall-through between switch labels [-Wimplicit-fallthrough]
        default:
        ^
drivers/gpu/drm/radeon/radeon_fb.c:170:2: note: insert 'break;' to avoid
fall-through
        default:
        ^
        break;
1 warning generated.

Clang's version of this warning is a little bit more pedantic than
GCC's. Add the missing break to satisfy it to match what has been done
all over the kernel tree.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This version brings along following fixes:
- Ensure DCN save init registers after VM setup
- Fix multi-display support for idle opt workqueue
- Use vblank control events for PSR enable/disable
- Create default dc_sink when fail reading EDID under MST
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Compilation of the workqueue fails if not building with the DCN config
option set.

[How]
Guard calls to the flush with the DCN config option to fix the build.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.

[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.

v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
PSR can disable the HUBP along with the OTG when PSR is active.

We'll hit a pageflip timeout when the OTG is disable because we're no
longer updating the CRTC vblank counter and the pflip high IRQ will
not fire on the flip.

In order to flip the page flip timeout occur we should modify the
enter/exit conditions to match DRM requirements.

[How]
Use our deferred handlers for DRM vblank control to notify DMCU(B)
when it can enable or disable PSR based on whether vblank is disabled or
enabled respectively.

We'll need to pass along the stream with the notification now because
we want to access the CRTC state while the CRTC is locked to get the
stream state prior to the commit.

Retain a reference to the stream so it remains safe to continue to
access and release that reference once we're done with it.

Enable/disable logic follows what we were previously doing in
update_planes.

The workqueue has to be flushed before programming streams or planes
to ensure that we exit out of idle optimizations and PSR before
these events occur if necessary.

To keep the skip count logic the same to avoid FBCON PSR enablement
requires copying the allow condition onto the DM IRQ parameters - a
field that we can actually access from the worker.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The current implementation for idle optimization support only has a
single work item that gets reshuffled into the system workqueue
whenever we receive an enable or disable event.

We can have mismatched events if the work hasn't been processed or if
we're getting control events from multiple displays at once.

This fixes this issue and also makes the implementation usable for
PSR control - which will be addressed in another patch.

[How]
We need to be able to flush remaining work out on demand for driver stop
and psr disable so create a driver specific workqueue instead of using
the system one. The workqueue will be single threaded to guarantee the
ordering of enable/disable events.

Refactor the queue to allocate the control work and deallocate it
after processing it.

Pass the acrtc directly to make it easier to handle psr enable/disable
in a later patch.

Rename things to indicate that it's not just MALL specific.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
While reading remote EDID via Startech 1-to-4 hub, occasionally we
won't get response in time and won't light up corresponding monitor.

Ideally, we can still add generic modes for userspace to choose to try
to light up the monitor and which is done in
drm_helper_probe_single_connector_modes(). So the main problem here is
that we fail .mode_valid since we don't create remote dc_sink for this
case.

[How]
Also add default dc_sink if we can't get the EDID.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

These registers have different address from other SMU V11 ASICs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As the fan control was guarded under manual mode before fan speed
RPM/PWM setting. Thus the extra check is totally redundant.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently, the readout of fan speed pwm is transited into percent-based
and then pwm-based. However, the transition into percent-based is totally
unnecessary and make the final output less accurate.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, we need a new way to
retrieving the fan speed RPM.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, we need a new way to
retrieving the fan speed PWM.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As the relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, both the RPM and PWM
settings need to be saved.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, we need a new way to
perform the fan speed RPM setting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Delete ras_if->name in the RAS ctx structure and remove related lines.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

KFDSVMRangeTest.SetGetAttributesTest randomly fails in stress test.

Note: Google Test filter = KFDSVMRangeTest.*
[==========] Running 18 tests from 1 test case.
[----------] Global test environment set-up.
[----------] 18 tests from KFDSVMRangeTest
[ RUN      ] KFDSVMRangeTest.BasicSystemMemTest
[       OK ] KFDSVMRangeTest.BasicSystemMemTest (30 ms)
[ RUN      ] KFDSVMRangeTest.SetGetAttributesTest
[          ] Get default atrributes
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure
Value of: expectedDefaultResults[i]
  Actual: 4294967295
Expected: outputAttributes[i].value
Which is: 0
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure
Value of: expectedDefaultResults[i]
  Actual: 4294967295
Expected: outputAttributes[i].value
Which is: 0
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:152: Failure
Value of: expectedDefaultResults[i]
  Actual: 4
Expected: outputAttributes[i].type
Which is: 2
[          ] Setting/Getting atrributes
[  FAILED  ]

the root cause is that svm work queue has not finished when svm_range_get_attr is called, thus
some garbage svm interval tree data make svm_range_get_attr get wrong result. Flush work queue before
iterate svm interval tree.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

change the workload type for some cards as it is needed.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commit 0979d432.
Revert this because it does not apply to all the cards.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When guest received FLR notification from host, it would
lock adapter into reset state. There will be no more
job submission and hardware access after that.

Then it should send a response to host that it has prepared
for host reset.
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Signed-off-by: Peng Ju Zhou <PengJu.Zhou@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

the following clock is only support voltage DPM, change attribute to RO:
1. pp_dpm_sclk
2. pp_dpm_mclk
3. pp_dpm_fclk
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

the following message is allowed in sriov mode:
1. GetEnabledSmuFeaturesLow
2. GetEnabledSmuFeaturesHigh
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v1:
1. change return value to avoid smu driver probe fails when FEATURE_PPT is
not enabled.
2. if FEATURE_PPT is not enabled, set power limit value to 0.

v2:
instead dev_err with dev_warn
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v1:
1. skip to load smu firmware in sriov mode for aldebaran chip
2. using vbios pptable if in sriov mode.

v2:
clean up smu driver code in sriov code path
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>