The Intel TyphoonPeak, GarfieldPeak Bluetooth controllers
support the Microsoft vendor extension and they are using
0xFC1E for VsMsftOpCode.

Verified on a GarfieldPeak device through bluetoothctl show
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Qualcomm WCN6855 Bluetooth controller supports the Microsoft vendor
extension, enable them by setting VsMsftOpCode to 0xFD70.

Verified on a WCN6855 device through bluetoothctl show
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Remove the btusb_table entry for 413c:8197 so the device is handled
by the later Dell vendor entry, which specifies patchram loading.

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=413c ProdID=8197 Rev= 1.12
S:  Manufacturer=Dell Computer Corp
S:  Product=DW380 Bluetooth Module
S:  SerialNumber=74E54354F609
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Ian Mackinnon <imackinnon@gmail.com>
Tested-By: Aathif Naseer <aathif394@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy() but in
this case it is better to use the scnprintf to simplify the arithmetic.

This is a previous step in the path to remove the strcpy() function
entirely from the kernel.
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.

As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.

Link: https://syzkaller.appspot.com/bug?extid=66264bf2fd0476be7e6c [1]
Reported-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Tested-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fixes the MGMT add_advertising command repsones with the
wrong opcode when it is trying to return the not supported error.

Fixes: cbbdfa6f ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

syzbot is hitting might_sleep() warning at hci_sock_dev_event()
due to calling lock_sock() with rw spinlock held [1].

It seems that history of this locking problem is a trial and error.

Commit b40df574 ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to lock_sock()
as an attempt to fix lockdep warning.

Then, commit 4ce61d1c ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix
sleep in atomic context warning.

Then, commit 4b5dd696 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().

Then, commit e305509e ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.

This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately reclaims
resources as soon as returning from hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.

Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_release_dev() which is called by bt_host_release when all references
to this unregistered device (which is a kobject) are gone.

Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Fixes: e305509e ("Bluetooth: use correct lock to prevent UAF of hdev object")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the valid le states quirk for WCN6855 and GarfieldPeak controller
so the 'central-peripheral' role is exposed in userspace.
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch allows the controller to suspend after a short period of
inactivity.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For chips that doesn't reset on suspend, we need to provide the correct
value of flow_control when it resumes. Therefore, store the flow
control value when reading from the config file to be reused upon
suspend.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some RTL chips resets the FW on suspend, so wakeup is disabled on
those chips. This patch introduces this WAKEUP_DISABLE flag so that
chips that doesn't reset FW on suspend can leave the flag unset and
is allowed to wake the host.

This patch also left RTL8822 WAKEUP_DISABLE flag unset, therefore
allowing it to wake the host, and preventing reprobing on resume.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add support for another Foxconn / Hon Hai device with MT7921 chip.

T:  Bus=05 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0cd Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

kernel-doc complains about a non-kernel-doc comment that uses "/**"
to begin the comment, so change it to just "/*".

drivers/bluetooth/btrsi.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
    * Copyright (c) 2017 Redpine Signals Inc.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

RTL8852 support MSFT HCI extension, therefore set the proper MSFT
opcode.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The bounds check of id is off-by-one and the comparison should
be >= rather >. Currently the WARN_ON_ONCE check does not stop
the out of range indexing of &ldev->ctx.table[id] so also add
a return path if the bounds are out of range.

Addresses-Coverity: ("Illegal address computation").
Fixes: 5609c185 ("6lowpan: iphc: add support for stateful compression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The LG LGSBWAC92/TWCM-K505D/EAT64454801/EAT64454802 (it goes by many
names) is a combo WiFi/Bluetooth module that's used in several models of
LG TVs. It uses the MediaTek MT7668AUN, which is already supported in
btusb, but this device has a non-MediaTek VID:PID pair so to get it to
work we just need to add it to the list of devices to probe.

Device from /sys/kernel/debug/usb/devices:

T:  Bus=09 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=043e ProdID=3109 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When reading the support debug features failed, there are not available
features init. Continue to set the debug features is illogical, we should
skip btintel_set_debug_features(), even if check it by "if (!features)".

Fixes: c453b10c ("Bluetooth: btusb: Configure Intel debug feature based on available support")
Signed-off-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Smatch complains that some of these struct members are not initialized
leading to a stack information disclosure:

    net/bluetooth/sco.c:778 sco_conn_defer_accept() warn:
    check that 'cp.retrans_effort' doesn't leak information

This seems like a valid warning.  I've added a default case to fix
this issue.

Fixes: 2f69a82a ("Bluetooth: Use voice setting in deferred SCO connection request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This add supports for IMC Networks Wireless_Device Media Chip
which contains the MT7921 chipset.

$ lsusb

Bus 001 Device 004: ID 13d3:3563 IMC Networks Wireless_Device

$ cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3563 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Wai Paulo Valerio Wang <waicool20@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The hci_suspend_notifier which was introduced last year, is causing
problems for uart attached btrtl devices. These devices may loose their
firmware and their baudrate setting over a suspend/resume.

Since we don't even know the baudrate after a suspend/resume recovering
from this is tricky. The driver solves this by treating these devices
the same as USB BT HCIs which drop of the bus during suspend.

Specifically the driver:
1. Simply unconditionally turns the device fully off during
   system-suspend to save maximum power.
2. Calls device_reprobe() from a workqueue to fully re-init the device
   from scratch on system-resume (unregistering the old HCI and
   registering a new HCI).

This means that these devices do not benefit from the suspend / resume
handling work done by the hci_suspend_notifier. At best this unnecessarily
adds some time to the suspend/resume time.

But in practice this is actually causing problems:

1. These btrtl devices seem to not like the HCI_OP_WRITE_SCAN_ENABLE(
SCAN_DISABLED) request being send to them when entering the
BT_SUSPEND_CONFIGURE_WAKE state. The same request send on
BT_SUSPEND_DISCONNECT works fine, but the second one send (unnecessarily?)
from the BT_SUSPEND_CONFIGURE_WAKE transition causes the device to hang:

[  573.497754] PM: suspend entry (s2idle)
[  573.554615] Filesystems sync: 0.056 seconds
[  575.837753] Bluetooth: hci0: Timed out waiting for suspend events
[  575.837801] Bluetooth: hci0: Suspend timeout bit: 4
[  575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -110

2. The PM_POST_SUSPEND / BT_RUNNING transition races with the
driver-unbinding done by the device_reprobe() work.
If the hci_suspend_notifier wins the race it is talking to a dead
device leading to the following errors being logged:

[  598.686060] Bluetooth: hci0: Timed out waiting for suspend events
[  598.686124] Bluetooth: hci0: Suspend timeout bit: 5
[  598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110

In both cases things still work, but the suspend-notifier is causing
these ugly errors getting logged and ut increase both the suspend- and
the resume-time by 2 seconds.

This commit avoids these problems by disabling the hci_suspend_notifier.

Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The return type of the function is bool and while NULL do evaluate to
false it's not very nice, fix this by explicitly returning false. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compiling without CONFIG_SYSCTL, this warning appears:

  net/ipv6/addrconf.c:99:12: error: 'ioam6_if_id_max' defined but not used [-Werror=unused-variable]
     99 | static u32 ioam6_if_id_max = U16_MAX;
        |            ^~~~~~~~~~~~~~~
  cc1: all warnings being treated as errors

Simply moving the declaration of this variable under ...

  #ifdef CONFIG_SYSCTL

... with other similar variables fixes the issue.

Fixes: 9ee11f0f ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: flower: conntrack offload

Louis Peens says:

This series takes the preparation from previous two series
and finally creates the structures and control messages
to offload the conntrack flows to the card. First we
do a bit of refactoring in the existing functions
to make them re-usable for the conntrack implementation,
after which the control messages are compiled and
transmitted to the card. Lastly we add stats handling
for the conntrack flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add in the logic to update flow stats. The flow stats from the nfp
is saved in the flow_pay struct, which is associated with the final
merged flow. This saves deltas however, so once read it needs to
be cleared. However the flow stats requests from the kernel is
from the other side of the chain, and a single tc flow from
the kernel can be merged into multiple other tc flows to form
multiple offloaded flows. This means that all linked flows
needs to be updated for each stats request.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the offload parts (ADD_FLOW/DEL_FLOW) calls to add and delete
the flows from the nfp.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile the offload flow metadata and add flow_pay to the offload
table. Also add in the delete paths. This does not include actual
offloading to the card yet, this will follow soon.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Combine the actions from the three different rules into one and
convert into the payload format expected by the nfp.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add in the code to compile match part of the payload that will be
sent to the firmware. This works similar to match.c does it, but
since three flows needs to be merged it iterates through all three
rules in a loop and combine the match fields to get the most strict
match as result.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This calculates the correct combined keylayers and key_layer_size
for the to-be-offloaded flow.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the action related offload functions to take in flow_rule *
as input instead of flow_cls_offload * as input. The flow_rule
parts of flow_cls_offload is the only part that is used in any
case, and this is required for more conntrack offload patches
which will follow later.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a small cleanup to pass in flow->rule to some of the compile
functions instead of extracting it every time. This is will also be
useful for conntrack patches later.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose and refactor the match compilation functions so that they
can be invoked externally. Also update the functions so they can
be called multiple times with the results OR'd together. This is
applicable for the flows-merging scenario, in which there could be
overlapped and non-conflicting match fields. This will be used
in upcoming conntrack patches. This is safe to do in the in the
single call case as well since both unmasked_data and mask_data
gets initialised to 0.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test if we actually can send/receive packets with MTU size. This kind of
issue was detected on ASIX HW with bogus EEPROM.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing stop and let phylib framework suspend attached PHY.

Fixes: e532a096 ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

asix_get_phyid() is used for two reasons here. To print debug message
with the PHY ID and to wait until the PHY is powered up.

After migrating to the phylib, we can read PHYID from sysfs. If polling
for the PHY is really needed, then we will need to handle it in the
phylib as well.

This change was tested with:
- ax88772a + internal PHY
- ax88772b + external PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly introduced switchdev_handle_fdb_{add,del}_to_device helpers
solved a problem but introduced another one. They have a severe design
bug: they do not propagate FDB events on foreign interfaces to us, i.e.
this use case:

         br0
        /   \
       /     \
      /       \
     /         \
   swp0       eno0
(switchdev)  (foreign)

when an address is learned on eno0, what is supposed to happen is that
this event should also be propagated towards swp0. Somehow I managed to
convince myself that this did work correctly, but obviously it does not.

The trouble with foreign interfaces is that we must reach a switchdev
net_device pointer through a foreign net_device that has no direct
upper/lower relationship with it. So we need to do exploratory searching
through the lower interfaces of the foreign net_device's bridge upper
(to reach swp0 from eno0, we must check its upper, br0, for lower
interfaces that pass the check_cb and foreign_dev_check_cb). This is
something that the previous code did not do, it just assumed that "dev"
will become a switchdev interface at some point, somehow, probably by
magic.

With this patch, assisted address learning on the CPU port works again
in DSA:

ip link add br0 type bridge
ip link set swp0 master br0
ip link set eno0 master br0
ip link set br0 up

[   46.708929] mscc_felix 0000:00:00.5 swp0: Adding FDB entry towards eno0, addr 00:04:9f:05:f4:ab vid 0 as host address

Fixes: 8ca07176 ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Reported-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Let switchdev drivers offload and unoffload bridge ports at their own convenience

This series introduces an explicit API through which switchdev drivers
mark a bridge port as offloaded or not:
- switchdev_bridge_port_offload()
- switchdev_bridge_port_unoffload()

Currently, the bridge assumes that a port is offloaded if
dev_get_port_parent_id(dev, &ppid, recurse=true) returns something, but
that is just an assumption that breaks some use cases (like a
non-offloaded LAG interface on top of a switchdev port, bridged with
other switchdev ports).

Along with some consolidation of the bridge logic to assign a "switchdev
offloading mark" to a port (now better called a "hardware domain"), this
series allows the bridge driver side to no longer impose restrictions on
that configuration.

Right now, all switchdev drivers must be modified to use the explicit
API, but more and more logic can then be placed centrally in the bridge
and therefore ease the job of a switchdev driver writer in the future.

For example, the first thing we can hook into the explicit switchdev
offloading API calls are the switchdev object and FDB replay helpers.
So far, these have only been used by DSA in "pull" mode (where the
driver must ask for them). Adding the replay helpers to other drivers
involves a lot of repetition. But by moving the helpers inside the
bridge port offload/unoffload hook points, we can move the entire replay
process to "push" mode (where the bridge provides them automatically).

The explicit switchdev offloading API will see further extensions in the
future.

The patches were split from a larger series for easier review:
https://patchwork.kernel.org/project/netdevbpf/cover/20210718214434.3938850-1-vladimir.oltean@nxp.com/

Changes in v6:
- Make the switchdev replay helpers opt-in
- Opt out of the replay helpers for mlxsw, rocker, prestera, sparx5,
  cpsw, am65-cpsw
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with commit 4f2673b3 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:

- an IP multicast group was host-joined on the bridge itself before any
  switchdev port joined the bridge, leading to the host MDB entries
  missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
  added to the FDB as an entry pointing towards the bridge device
  itself, but with no switchdev ports being part of the bridge yet, this
  local FDB entry would remain unknown to the switchdev hardware
  database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
  before any switchdev port joined that LAG, leading to the hardware
  database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
  remained part of the bridge, and all FDB/MDB/VLAN entries remained
  installed in the hardware database of the switchdev port.

Also, since commit 0d2cfbd4 ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.

With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.

To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).

Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.

Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
  blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
  disambiguate between which port is targeted, when multiple ports are
  lowers of the same LAG that is a bridge port. Most of the drivers pass
  NULL to this argument, except the ones that support LAG offload and have
  the proper context check already in place in the switchdev blocking
  notifier handler.

Also unexport the replay helpers, since nobody except the bridge calls
them directly now.

Note that:
(a) we abuse the terminology slightly, because FDB entries are not
    "switchdev objects", but we count them as objects nonetheless.
    With no direct way to prove it, I think they are not modeled as
    switchdev objects because those can only be installed by the bridge
    to the hardware (as opposed to FDB entries which can be propagated
    in the other direction too). This is merely an abuse of terms, FDB
    entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
    ports, just the countable stuff (the objects). The reason for this
    is simple: no universal and symmetric way to sync and unsync them is
    known. For example, VLAN filtering: what to do on unsync, disable or
    leave it enabled? Similarly, STP state, ageing timer, etc etc. What
    a switchdev port does when it becomes standalone again is not really
    up to the bridge's competence, and the driver should deal with it.
    On the other hand, replaying deletions of switchdev objects can be
    seen a matter of cleanup and therefore be treated by the bridge,
    hence this patch.

We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:

- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
  so br_vlan_replay() should not do anything for the new drivers on
  which we call it. The existing drivers where there was even a slight
  possibility for there to exist a VLAN on a bridge port before they
  join it are already guarded against this: mlxsw and prestera deny
  joining LAG interfaces that are members of a bridge.

- br_fdb_replay() should now notify of local FDB entries, but I patched
  all drivers except DSA to ignore these new entries in commit
  2c4eca3e ("net: bridge: switchdev: include local flag in FDB
  notifications"). Driver authors can lift this restriction as they
  wish, and when they do, they can also opt into the FDB replay
  functionality.

- br_mdb_replay() should fix a real issue which is described in commit
  4f2673b3 ("net: bridge: add helper to replay port and host-joined
  mdb entries"). However most drivers do not offload the
  SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
  offload this switchdev object, and I don't completely understand the
  way in which they offload this switchdev object anyway. So I'll leave
  it up to these drivers' respective maintainers to opt into
  br_mdb_replay().

So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
  helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode

An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/

Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a desire to make the object and FDB replay helpers optional
when moving them inside the bridge driver. For example a certain driver
might not offload host MDBs and there is no case where the replay
helpers would be of immediate use to it.

So it would be nice if we could allow drivers to pass NULL pointers for
the atomic and blocking notifier blocks, and the replay helpers to do
nothing in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).

Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.

Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.

       +-- br0 ---+
      / /   |      \
     / /    |       \
    /  |    |      bond0
   /   |    |     /    \
 swp0 swp1 swp2 swp3 swp4

There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.

But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.

- If we set it to 0, then the bridge will forward it towards swp1, swp2
  and bond0. But the switch has already forwarded it towards swp1 and
  swp2 (not to bond0, remember, that isn't offloaded, so as far as the
  switch is concerned, ports swp3 and swp4 are not looking up the FDB,
  and the entire bond0 is a destination that is strictly behind the
  CPU). But we don't want duplicated traffic towards swp1 and swp2, so
  it's not ok to set skb->offload_fwd_mark = 0.

- If we set it to 1, then the bridge will not forward the skb towards
  the ports with the same switchdev mark, i.e. not to swp1, swp2 and
  bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
  have forwarded the skb there.

So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.

A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.

Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:

     ip link set swp0 master br0
                  |
                  v
 br_add_if() calls netdev_master_upper_dev_link()
                  |
                  v
        call_netdevice_notifiers
                  |
                  v
       dsa_slave_netdevice_event
                  |
                  v
        oh, hey! it's for me!
                  |
                  v
           .port_bridge_join

What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:

     ip link set swp0 master br0
                  |
                  v
 br_add_if() calls netdev_master_upper_dev_link()
                  |
                  v                    bridge: Aye! I'll use this
        call_netdevice_notifiers           ^  ppid as the
                  |                        |  hardware domain for
                  v                        |  this port, and zero
       dsa_slave_netdevice_event           |  if I got nothing.
                  |                        |
                  v                        |
        oh, hey! it's for me!              |
                  |                        |
                  v                        |
           .port_bridge_join               |
                  |                        |
                  +------------------------+
             switchdev_bridge_port_offload(swp0, swp0)

Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.

The offload case:

    ip link set bond0 master br0
                  |
                  v
 br_add_if() calls netdev_master_upper_dev_link()
                  |
                  v                    bridge: Aye! I'll use this
        call_netdevice_notifiers           ^  ppid as the
                  |                        |  switchdev mark for
                  v                        |        bond0.
       dsa_slave_netdevice_event           | Coincidentally (or not),
                  |                        | bond0 and swp0, swp1, swp2
                  v                        | all have the same switchdev
        hmm, it's not quite for me,        | mark now, since the ASIC
         but my driver has already         | is able to forward towards
           called .port_lag_join           | all these ports in hw.
          for it, because I have           |
      a port with dp->lag_dev == bond0.    |
                  |                        |
                  v                        |
           .port_bridge_join               |
           for swp3 and swp4               |
                  |                        |
                  +------------------------+
            switchdev_bridge_port_offload(bond0, swp3)
            switchdev_bridge_port_offload(bond0, swp4)

And the non-offload case:

    ip link set bond0 master br0
                  |
                  v
 br_add_if() calls netdev_master_upper_dev_link()
                  |
                  v                    bridge waiting:
        call_netdevice_notifiers           ^  huh, switchdev_bridge_port_offload
                  |                        |  wasn't called, okay, I'll use a
                  v                        |  hwdom of zero for this one.
       dsa_slave_netdevice_event           :  Then packets received on swp0 will
                  |                        :  not be software-forwarded towards
                  v                        :  swp1, but they will towards bond0.
         it's not for me, but
       bond0 is an upper of swp3
      and swp4, but their dp->lag_dev
       is NULL because they couldn't
            offload it.

Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.

This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.

Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.

For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.

Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>