HDAudio implementation found in sound/pci/hda expects a valid stream
pointer in substream->runtime->private_data location. For ASoC users,
that should point to a valid link stream which is assigned when BE
opens.

As BE borrows its runtime from FE, the information may be lost when
reparenting comes into picture - see dpcm_be_reparent(). To support the
DPCM reparenting functionality for HDAudio scenarios while still
fulfilling expectations of HDAudio common code, have all FEs point to
the same private data.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221118113052.1340593-1-cezary.rojewski@intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Allwinner D1 SoC has a DMIC codec like the one in the H6. It appears
to be register-compatible with the H6 variant, and the existing Linux
driver has been tested on a D1-based board, the Lichee RV 86 Panel.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Ban Tao <fengzheng923@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221116034621.37762-1-samuel@sholland.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Smatch report warning as follows:

sound/soc/amd/acp/acp-platform.c:199 acp_dma_open() warn:
  '&stream->list' not removed from list

If snd_pcm_hw_constraint_integer() fails in acp_dma_open(),
stream will be freed, but stream->list will not be removed from
adata->stream_list, then list traversal may cause UAF.

Fix by adding the newly allocated stream to the list once it's fully
initialised.

Fixes: 7929985c ("ASoC: amd: acp: Initialize list to store acp_stream during pcm_open")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221118030056.3135960-1-cuigaosheng1@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add rt1015p speaker amplifier support with a new board info
'adl_rt1015p_nau8825' which supports NAU8825 on SSP0 and ALC1015Q on
SSP1.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221117231919.112483-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

We may check ops before spending resources on memory allocation.
While at it, utilize dev_get_platdata() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221117103223.74425-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Code can be a bit simpler with dev_err_probe().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221109163759.1158837-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

If probe fails, toggle shutdown via GPIO to save power and reverse
probe actions.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221109163759.1158837-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Move acp63_dev_data structure from PCI driver to acp header file.
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Link: https://lore.kernel.org/r/20221116105938.762550-2-Syed.SabaKareem@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Update macros using ps platform naming convention.
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Link: https://lore.kernel.org/r/20221116105938.762550-1-Syed.SabaKareem@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Ajye Huang <ajye_huang@compal.corp-partner.google.com>:

v1:
- machine driver:
  - Adds the combination of headset codec ALC5682I-VD + amp rt1019p.
  - Remove the duplicate code in machine driver.

Ajye Huang (2):
  ASoC: Intel: sof_rt5682: add support for ALC5682I-VD with amp rt1019p
  ASoC: Intel: sof rt5682: remove the duplicate codes

 sound/soc/intel/boards/sof_rt5682.c               | 7 +------
 sound/soc/intel/common/soc-acpi-intel-adl-match.c | 4 ++--
 2 files changed, 3 insertions(+), 8 deletions(-)

--
2.25.1

This is the initial amplifier driver for rt1318 SDCA version.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221108092727.13011-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove the redundant code to prevent user confuse.
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221108042716.2930255-3-ajye_huang@compal.corp-partner.google.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch adds the driver data for two rt1019 speaker amplifiers on
SSP1 and ALC5682I-VD on SSP0 for ADL platform.
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221108042716.2930255-2-ajye_huang@compal.corp-partner.google.comSigned-off-by: Mark Brown <broonie@kernel.org>

The actual space for struct snd_soc_component has been allocated by
snd_soc_register_component, here rtd's components are pointers to
components, I replace the base size from *component to component.
Signed-off-by: lishqchn <lishqchn@qq.com>
Link: https://lore.kernel.org/r/tencent_59850BB028662B6F2D49D7F3624AB84CCF05@qq.comSigned-off-by: Mark Brown <broonie@kernel.org>

DMIC Paths into LPASS digital codec can go via tx-macro or va-macro codec, add
support to tx-macro path as va-macro path is already supported.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221115065430.4126-1-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/202211111641514826535@zte.com.cnSigned-off-by: Mark Brown <broonie@kernel.org>

kasprintf() would return NULL pointer when kmalloc() fail to allocate.
Need to check the return pointer before calling strcmp().

Fixes: 7a824e21 ("ASoC: mmp: add audio dma support")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Link: https://lore.kernel.org/r/20221114085629.1910435-1-zengheng4@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

<linux/gcd.h> is not needed for these drivers. Remove the corresponding
#include.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/875ca433849025edf8c23624cf29b0e2250bba50.1668287523.git.christophe.jaillet@wanadoo.frSigned-off-by: Mark Brown <broonie@kernel.org>

Fix build errors when GPIOLIB is not set/enabled:

../sound/soc/codecs/wsa883x.c: In function 'wsa883x_probe':
../sound/soc/codecs/wsa883x.c:1394:25: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_regulator_get_optional'? [-Werror=implicit-function-declaration]
         wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown",
../sound/soc/codecs/wsa883x.c:1395:49: error: 'GPIOD_FLAGS_BIT_NONEXCLUSIVE' undeclared (first use in this function)
         GPIOD_FLAGS_BIT_NONEXCLUSIVE);
../sound/soc/codecs/wsa883x.c:1414:9: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
         gpiod_direction_output(wsa883x->sd_n, 1);

Fixes: 43b8c7dc ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Banajit Goswami <bgoswami@quicinc.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221108001829.5100-1-rdunlap@infradead.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The shutdown GPIO is active low (SD_N), but this depends on actual board
layout.  Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.

Invert the GPIO to match logical value.

Fixes: 43b8c7dc ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221110133512.478831-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Use correct polarity in example and powerdown-gpios description.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221110133512.478831-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:

Add 2 Dell SKU support.

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

Add support for two RaptorLake SoundWire SKUs and one test board for
MeteorLake.

There will be additional RaptorLake SKUs shared when validation is
complete.

Audio Graph Card2 has been announcing "Audio Graph Card2 is
still under Experimental stage", but it is time to remove it.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k042nm6s.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

The description was copied from APM driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221111091328.31549-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

There are some Dell SKUs that need to set the parameters of the
crossover filter (biquad).  Each amplifier connects to one tweeter
speaker and one woofer speaker.  We should control HPF/LPF to output the
proper frequency for the different speakers.  If the codec driver got
the BQ parameters from the device property, it will apply these
parameters to the hardware.

Audio hardware configuration of SKU 0C40 product is rt711 on link2,
two rt1316s on link0 and link1, rt714 on link 3.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111045016.46573-5-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

SKU 0C40 product supports a SoundWire headset codec, SoundWire
capture from local microphones and two SoundWire amplifiers.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111045016.46573-4-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Audio hardware configuration of SKU 0C10 product is rt714 on link0,
two rt1316s on link1 and link2
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111045016.46573-3-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

SKU 0C10 product supports SoundWire capture from local microphone
and two SoundWire amplifiers(no headset codec).
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111045016.46573-2-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support to the following daughter card:

SDW0: MX98373 Speaker
SDW2: ALC5682 Headset

Share same driver data used by sof_sdw driver for mtlrvp.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Audio hardware configuration of SKU 0C40 product is rt711 on link2,
two rt1316s on link0 and link1, rt714 on link 3.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

SKU 0C40 product supports a SoundWire headset codec, SoundWire
capture from local microphones and two SoundWire amplifiers.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Audio hardware configuration of SKU 0C10 product is rt714 on link0,
two rt1316s on link1 and link2
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

SKU 0C10 product supports SoundWire capture from local microphone
and two SoundWire amplifiers(no headset codec).
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

If we have several instances of WSA macro, each one of them should
register clock with unique name, so parse clock-output-names for this.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221103195341.174972-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The purpose of clock-output-names is to customize desired clock name,
not use one, same name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221103195341.174972-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The Dell SKU 0B00/0B01/0AFE/0AFF model needs the BQ params for the tweeter/woofer.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20221109091317.17240-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Dell SKU 0A5D/0A5E/0990/098F model needs the BQ params for the tweeter/woofer.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20221109091306.17221-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

If the machine driver level sets the BQ params into the device property,
the codec driver will get the BQ params and apply them.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20221109091244.17198-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>