- 13 Dec, 2015 18 commits
-
-
Raanan Avargil authored
i219-LM (3) is a LOM that will be available on systems with the Lewisburg Platform Controller Hub (PCH) chipset from Intel. This patch provides the initial support for the device. Signed-off-by:
Raanan Avargil <raanan.avargil@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jarod Wilson authored
Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the suggestion of Alexander Duyck, and use io_addr in more places, so that we don't have the need to call E1000_REMOVED (which simply looks for a null hw_addr) nearly as much. Signed-off-by:
Jarod Wilson <jarod@redhat.com> Acked-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
-
Jan Beulich authored
The combined effect of commits 6423fc34 ("igb: do not re-init SR-IOV during probe") and ceee3450 ("igb: make sure SR-IOV init uses the right number of queues") causes VFs no longer getting set up, leading to NULL pointer dereferences due to the adapter's ->vf_data being NULL while ->vfs_allocated_count is non-zero. The first commit not only neglected the side effect of igb_sriov_reinit() that the second commit tried to account for, but also that of setting IGB_FLAG_HAS_MSIX, without which igb_enable_sriov() is effectively a no-op. Calling igb_{,re}set_interrupt_capability() as done here seems to address this, but I'm not sure whether this is better than sinply reverting the other two commits. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Tested-by:
-
Raanan Avargil authored
Due to timing changes to the ME firmware in Skylake, this timer needs to be increased to 300ms. Signed-off-by:
-
Dmitry Fleytman authored
This patch fixes possible division by zero in receive interrupt handler when working without adaptive interrupt moderation. The adaptive interrupt moderation mechanism is typically disabled on jumbo MTUs. Signed-off-by:
Dmitry Fleytman <dmitry@daynix.com> Signed-off-by:
Leonid Bloch <leonid@daynix.com> Tested-by:
-
Janusz Wolak authored
Signed-off-by:
Janusz Wolak <januszvdm@gmail.com> Acked-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
-
Jean Sacren authored
By using goto statement, we can achieve sharing the same exit path so that code duplication could be minimized. Signed-off-by:
Jean Sacren <sakiwit@gmail.com> Tested-by:
-
Jean Sacren authored
Due to historical reason, 'phy_data' has never been included in the kernel doc. Fix it so that the requirement could be fulfilled. Signed-off-by:
-
Jean Sacren authored
The local variable 'ret' doesn't serve much purpose so we might as well clean it up. Signed-off-by:
-
Jean Sacren authored
Use 'That' to replace 'The' so that the comment would make sense. Signed-off-by:
-
Jean Sacren authored
The checking logic needed some clean-up work, so we rewrite it by checking for break first. With that change in place, we can even move the second check for goto statement outside of the loop. As this is merely a cleanup, no functional change is involved. The questionable 'tmp != 0xFF' is intentionally left alone. Mark Rustad and Alexander Duyck contributed to this patch. CC: Mark Rustad <mark.d.rustad@intel.com> CC: Alex Duyck <aduyck@mirantis.com> Signed-off-by:
-
Todd Fujinaka authored
The i210 has two EEPROM access registers that are located in non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously and EEMNGCTL should also be corrected. Reported-by:
Roman Hodek <roman.aud@siemens.com> Signed-off-by:
Todd Fujinaka <todd.fujinaka@intel.com> Tested-by:
-
Janusz Wolak authored
Signed-off-by:
-
Jarod Wilson authored
I've got a startech thunderbolt dock someone loaned me, which among other things, has the following device in it: 08:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) This hotplugs just fine (kernel 4.2.0 plus a patch or two here): [ 863.020315] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.18-k [ 863.020316] igb: Copyright (c) 2007-2014 Intel Corporation. [ 863.028657] igb 0000:08:00.0: enabling device (0000 -> 0002) [ 863.062089] igb 0000:08:00.0: added PHC on eth0 [ 863.062090] igb 0000:08:00.0: Intel(R) Gigabit Ethernet Network Connection [ 863.062091] igb 0000:08:00.0: eth0: (PCIe:2.5Gb/s:Width x1) e8:ea:6a:00:1b:2a [ 863.062194] igb 0000:08:00.0: eth0: PBA No: 000200-000 [ 863.062196] igb 0000:08:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s) [ 863.064889] igb 0000:08:00.0 enp8s0: renamed from eth0 But disconnecting it is another story: [ 1002.807932] igb 0000:08:00.0: removed PHC on enp8s0 [ 1002.807944] igb 0000:08:00.0 enp8s0: PCIe link lost, device now detached [ 1003.341141] ------------[ cut here ]------------ [ 1003.341148] WARNING: CPU: 0 PID: 199 at lib/iomap.c:43 bad_io_access+0x38/0x40() [ 1003.341149] Bad IO access at port 0x0 () [ 1003.342767] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi igb dca firewire_ohci firewire_core crc_itu_t rfcomm ctr ccm arc4 iwlmvm mac80211 fuse xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter bnep dm_mirror dm_region_hash dm_log dm_mod coretemp x86_pkg_temp_thermal intel_powerclamp kvm_intel snd_hda_codec_hdmi kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg [ 1003.342793] ansi_cprng aesni_intel hp_wmi aes_x86_64 iTCO_wdt lrw iTCO_vendor_support ppdev gf128mul sparse_keymap glue_helper ablk_helper cryptd snd_hda_codec_realtek snd_hda_codec_generic microcode snd_hda_intel uvcvideo iwlwifi snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hda_core videobuf2_core snd_hwdep btusb v4l2_common btrtl snd_seq btbcm btintel videodev cfg80211 snd_seq_device rtsx_pci_ms bluetooth pcspkr input_leds i2c_i801 media parport_pc memstick rfkill sg lpc_ich snd_pcm 8250_fintek parport joydev snd_timer snd soundcore hp_accel ie31200_edac mei_me lis3lv02d edac_core input_polldev mei hp_wireless shpchp tpm_infineon sch_fq_codel nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables autofs4 xfs libcrc32c sd_mod sr_mod cdrom rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci [ 1003.342822] nouveau ahci libahci mxm_wmi e1000e xhci_pci hwmon ptp drm_kms_helper pps_core xhci_hcd ttm wmi video ipv6 [ 1003.342839] CPU: 0 PID: 199 Comm: kworker/0:2 Not tainted 4.2.0-2.el7_UNSUPPORTED.x86_64 #1 [ 1003.342840] Hardware name: Hewlett-Packard HP ZBook 15 G2/2253, BIOS M70 Ver. 01.07 02/26/2015 [ 1003.342843] Workqueue: pciehp-3 pciehp_power_thread [ 1003.342844] ffffffff81a90655 ffff8804866d3b48 ffffffff8164763a 0000000000000000 [ 1003.342846] ffff8804866d3b98 ffff8804866d3b88 ffffffff8107134a ffff8804866d3b88 [ 1003.342847] ffff880486f46000 ffff88046c8a8000 ffff880486f46840 ffff88046c8a8098 [ 1003.342848] Call Trace: [ 1003.342852] [<ffffffff8164763a>] dump_stack+0x45/0x57 [ 1003.342855] [<ffffffff8107134a>] warn_slowpath_common+0x8a/0xc0 [ 1003.342857] [<ffffffff810713c6>] warn_slowpath_fmt+0x46/0x50 [ 1003.342859] [<ffffffff8133719e>] ? pci_disable_msix+0x3e/0x50 [ 1003.342860] [<ffffffff812f6328>] bad_io_access+0x38/0x40 [ 1003.342861] [<ffffffff812f6567>] pci_iounmap+0x27/0x40 [ 1003.342865] [<ffffffffa0b728d7>] igb_remove+0xc7/0x160 [igb] [ 1003.342867] [<ffffffff8132189f>] pci_device_remove+0x3f/0xc0 [ 1003.342869] [<ffffffff81433426>] __device_release_driver+0x96/0x130 [ 1003.342870] [<ffffffff814334e3>] device_release_driver+0x23/0x30 [ 1003.342871] [<ffffffff8131b404>] pci_stop_bus_device+0x94/0xa0 [ 1003.342872] [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0 [ 1003.342873] [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0 [ 1003.342874] [<ffffffff8131b516>] pci_stop_and_remove_bus_device+0x16/0x30 [ 1003.342876] [<ffffffff81333f5b>] pciehp_unconfigure_device+0x9b/0x180 [ 1003.342877] [<ffffffff81333a73>] pciehp_disable_slot+0x43/0xb0 [ 1003.342878] [<ffffffff81333b6d>] pciehp_power_thread+0x8d/0xb0 [ 1003.342885] [<ffffffff810881b2>] process_one_work+0x152/0x3d0 [ 1003.342886] [<ffffffff8108854a>] worker_thread+0x11a/0x460 [ 1003.342887] [<ffffffff81088430>] ? process_one_work+0x3d0/0x3d0 [ 1003.342890] [<ffffffff8108ddd9>] kthread+0xc9/0xe0 [ 1003.342891] [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180 [ 1003.342893] [<ffffffff8164e29f>] ret_from_fork+0x3f/0x70 [ 1003.342894] [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180 [ 1003.342895] ---[ end trace 65a77e06d5aa9358 ]--- Upon looking at the igb driver, I see that igb_rd32() attempted to read from hw_addr and failed, so it set hw->hw_addr to NULL and spit out the message in the log output above, "PCIe link lost, device now detached". Well, now that hw_addr is NULL, the attempt to call pci_iounmap is obviously not going to go well. As suggested by Mark Rustad, do something similar to what ixgbe does, and save a copy of hw_addr as adapter->io_addr, so we can still call pci_iounmap on it on teardown. Additionally, for consistency, make the pci_iomap call assignment directly to io_addr, so map and unmap match. Signed-off-by:
-
Dmitriy Vyukov authored
e1000_clean_tx_irq cleans buffers and sets tx_ring->next_to_clean, then e1000_xmit_frame reuses the cleaned buffers. But there are no memory barriers when buffers gets recycled, so the recycled buffers can be corrupted. Use smp_store_release to update tx_ring->next_to_clean and smp_load_acquire to read tx_ring->next_to_clean to properly hand off buffers from e1000_clean_tx_irq to e1000_xmit_frame. The data race was found with KernelThreadSanitizer (KTSAN). Signed-off-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
-
Todd Fujinaka authored
Initialize the 88E1543 PHY. Signed-off-by:
-
Joern Engel authored
Code was responsible for ~150ms scheduler latencies. Signed-off-by:
Joern Engel <joern@logfs.org> Signed-off-by:
Spencer Baugh <sbaugh@catern.com> Tested-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2015-12-12 This series contains updates to ixgbe only. Alex Duyck provides almost off of the changes in this series. First, add a check to make sure mac_table was actually allocated and is not NULL to ensure we do not get a NULL pointer dereference further down the line. Fixed SR-IOV VLAN pool configuration since the code for checking the PF bit in ixgbe_set_vf_vlan_msg() was using the wrong offset. Cleanup/simplify the logic for setting the VFTA register by removing the number of conditional checks needed. Fixed a number of issues within the VLVF and VLFB configuration by simplifying the code. Added support for bypassing the VLVF entry creation when the PF is adding a new VLAN. Reduced the complexity of the search function used for finding a VLVF entry associated with a given VLAN ID. Added support for VLAN promiscuous with SR-IOV enabled by setting all the bits in the VFTA and all of the VLVF bits associated with teh pool belonging to the PF, in addition to cleaning up those same bits in the event of promiscuous mode being disabled. Fixed and issue where we ran the risk of leaking an address into pool 0 which really belongs to VF 0 when SR-IOV is enabled. Emil fixes an issue with some X550 devices which can connect at 2.5Gbps, but only with certain link partners during fail-over, so to avoid confusion, we do not report it as supported. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
- 12 Dec, 2015 22 commits
-
-
Daniel Borkmann authored
Add support for renaming and hard links to the fs. Most of this can be implemented by using simple library operations under the same constraints that we don't use a reserved name like elsewhere. Linking can be useful to share/manage things like maps across subsystem users. It works within the file system boundary, but is not allowed for directories. Symbolic links are explicitly not implemented here, as it can be better done already by doing bind mounts inside bpf fs to set up shared directories f.e. useful when using volumes in docker containers that map a private working directory into /sys/fs/bpf/ which contains itself a bind mounted path from the host's /sys/fs/bpf/ mount that is shared among multiple containers. For single maps instead of whole directory, hard links can be easily used to do the same. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Emil Tantilov authored
Some X550 devices can connect at 2.5Gbps during fail-over, but only with certain link partners. Also setting the advertised speed will not work so we do not report it as supported to avoid confusion. Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
-
Alexander Duyck authored
This patch guarantees that the VFs do not have access to VLANs that they were not supposed to. What this patch does is add code so that we delete the previous port VLAN after adding a new one, and if we reset the VF we clear all of the filters associated with it. Previously the code was leaving all previous VLANs mapped to the VF and they didn't get deleted unless the VF specifically requested it or if the PF itself was reset. Signed-off-by:
-
Alexander Duyck authored
This patch makes certain that we clear the pool mappings added when we configure default MAC addresses for the interface. Without this we run the risk of leaking an address into pool 0 which really belongs to VF 0 when SR-IOV is enabled. Signed-off-by:
-
Alexander Duyck authored
This patch is a follow-on for enabling VLAN promiscuous and allowing the PF to add VLANs without adding a VLVF entry. What this patch does is go through and free the VLVF registers if they are not needed as the VLAN belongs only to the PF which is the default pool. Signed-off-by:
-
Alexander Duyck authored
This patch adds support for VLAN promiscuous with SR-IOV enabled. The code prior to this patch was only adding the PF to VLANs that the VF had added. As such enabling promiscuous mode would actually not add any additional VLAN filters so visibility was limited. This lead to a number of issues as the bridge and OVS would expect us to accept all VLAN tagged packets when promiscuous mode was enabled, and instead we would filter out most if not all depending on the configuration of the PF. With this patch what we do is set all the bits in the VFTA and all of the VLVF bits associated with the pool belonging to the PF. By doing this the PF is guaranteed to receive all VLAN tagged traffic associated with the RAR filters assigned to the PF. In addition we will clean up those same bits in the event of promiscuous mode being disabled. Signed-off-by:
-
Alexander Duyck authored
This patch is meant to reduce the complexity of the search function used for finding a VLVF entry associated with a given VLAN ID. The previous code was searching from bottom to top. I reordered it to search from top to bottom. In addition I pulled an AND statement out of the loop and instead replaced it with an OR statement outside the loop. This should help to reduce the overall size and complexity of the function. There was also some formatting I cleaned up in regards to whitespace and such. Signed-off-by:
-
Alexander Duyck authored
This patch adds support for bypassing the VLVF entry creation when the PF is adding a new VLAN. The advantage to doing this is that we can then save the VLVF entries for the VFs which must have them in order to function, versus the PF which can fall back on the default pool entry. Signed-off-by:
-
Alexander Duyck authored
This patch addresses several issues within the VLVF and VLVFB configuration First was the fact that code was overly complicated with multiple conditional paths depending on if we adding or removing and which bit we were going to add or remove. Instead of messing with all that I have simplified it by using (vid / 32) and (1 - vid / 32) to identify our register and the other vlvfb register. Second was the fact that we were likely leaking a few packets into the PF in cases where we were deleting an entry and the VFTA filter for that entry as the ordering was such that we deleted the pool and then the VLAN filter instead of the other way around. I have updated that by adding a check for no bits being set and if that occurs we clear things up in the proper order. Signed-off-by:
-
Alexander Duyck authored
In order to clear the way for upcoming work I thought it best to drop the level of indent in the ixgbe_set_vfta_generic function. Most of the code is held in the virtualization specific section. So the easiest approach is to just add a jump label and jump past the bulk of the code if it is not enabled. Signed-off-by:
-
Alexander Duyck authored
This patch simplifies the logic for setting the VFTA register by removing the number of conditional checks needed. Instead we just use some boolean logic to generate vfta_delta, and if that is set then we xor the vfta by that value and write it back. Signed-off-by:
-
Alexander Duyck authored
The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the wrong offset and as a result it was pulling the VLAN off of the PF even if there were VFs numbered greater than 40 that still had the VLAN enabled. Signed-off-by:
-
Alexander Duyck authored
Add a check to make certain mac_table was actually allocated and is not NULL. If it is NULL return -ENOMEM and allow the probe routine to fail rather then causing a NULL pointer dereference further down the line. Signed-off-by:
-
Jiri Pirko authored
Sensor index should be passed instead of 0. For now, this does not make a difference, since there is so far only one temperature sensor exposed by HW. Fixes: 89309da3 ("mlxsw: core: Implement temperature hwmon interface") Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Jiri Pirko authored
Fix copy & paste error in MTPM unpack helper. Fixes: 85926f87 ("mlxsw: reg: Add definition of temperature management registers") Signed-off-by:
-
David S. Miller authored
Saeed Mahameed says: ==================== mlx5 improved flow steering management First two patches fixes some minor issues in recently introduced SRIOV code. The other seven patches modifies the driver's code that manages flow steering rules with Connectx-4 devices. Basic introduction: The flow steering device specification model is composed of the following entities: Destination (either a TIR/Flow table/vport), where TIR is RSS end-point, vport is the VF eSwitch port in SRIOV. Flow table entry (FTE) - the values used by the flow specification Flow table group (FG) - the masks used by the flow specification Flow table (FT) - groups several FGs and can serve as destination The flow steering software entities: In addition to the device objects, the software have two more objects: Priorities - group several FTs. Handles order of packet matching. Namespaces - group several priorities. Namespace are used in order to isolate different usages of steering (for example, add two separate namespaces, one for the NIC driver and one for E-Switch FDB). The base data structure for the flow steering management is a tree and all the flow steering objects such as (Namespace/Flow table/Flow Group/FTE/etc.) are represented as a node in the tree, e.g.: Priority-0 -> FT1 -> FG -> FTE -> TIR (destination) Priority-1 -> FT2 -> FG-> FTE -> TIR (destination) Matching begins in FT1 flow rules and if there is a miss on all the FTEs then matching continues on the FTEs in FT2. The new implementation solves/improves the following issues in the current code: 1) The new impl. supports multiple destinations, the search for existing rule with the same matching value is performed by the flow steering management. In the current impl. the E-switch FDB management code needs to search for existing rules before calling to the add rule function. 2) The new impl. manages the flow table level, in the current implementation the consumer states the flow table level when new flow table is created without any knowledge about the levels of other flow tables. 3) In the current impl. the consumer can't create or destroy flow groups dynamically, the flow groups are passed as argument to the create flow table API. The new impl. exposes API for create/destroy flow group. The series is built as follows: Patch #1 add flow steering API firmware commands. Patch #2 add tree operation of the flow steering tree: add/remove node, initialize node and take reference count on a node. Patch #3 add essential algorithms for managing the flow steering. Patch #4 Initialize the flow steering tree, flow steering initialization is based on static tree which illustrates the flow steering tree when the driver is loaded. Patch #5 is the main patch of the series. It introduce the flow steering API. Patch #6 Expose the new flow steering API and remove the old one. The Ethernet flow steering follows the existing implementation, but uses the new steering API. Patch #7 Rename en_flow_table.c to en_fs.c in order to be aligned with the new flow steering files. ==================== Signed-off-by: -
Maor Gottlieb authored
Rename en_flow_table.c to en_fs.c in order to be aligned with the new flow steering files. Signed-off-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Moni Shoua <monis@mellanox.com> Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Maor Gottlieb authored
Expose the new flow steering API and remove the old one. Few changes are required: 1. The Ethernet flow steering follows the existing implementation, but uses the new steering API. The old flow steering implementation is removed. 2. Move the E-switch FDB management to use the new API. 3. When driver is loaded call to mlx5_init_fs which initialize the flow steering tree structure, open namespaces for NIC receive and for E-switch FDB. 4. Call to mlx5_cleanup_fs when the driver is unloaded. Signed-off-by:
-
Maor Gottlieb authored
Flow steering initialization is based on static tree which illustrates the flow steering tree when the driver is loaded. The initialization considers the max supported flow table level of the device, a minimum of 2 kernel flow tables(vlan and mac) are required to have kernel flow table functionality. The tree structures when the driver is loaded: root_namespace(receive nic) | priority-0 (kernel priority) | namespace(kernel namespace) | priority-0 (flow tables priority) In the following patches, When the EN driver will use the flow steering API, it create two flow tables and their flow groups under priority-0(flow tables priority). Signed-off-by:
-
Maor Gottlieb authored
Introducing the following objects: mlx5_flow_root_namespace: represent the root of specific flow table type tree(e.g NIC receive, FDB, etc..) mlx5_flow_group: define the mask of the flow specification. fs_fte(flow steering flow table entry): defines the value of the flow specification. The following describes the relationships between the tree objects: root_namespace --> priorities -->namespaces --> priorities -->flow-tables --> flow-groups --> flow-entries --> destinations When we create new object(flow table/flow group/flow table entry), we call to the FW command and then we add the related sw object to the tree. When we destroy object, e.g. call to mlx5_destroy_flow_table, we use the tree node destructor for destroying the FW object and remove the node from the tree. Signed-off-by:
-
Maor Gottlieb authored
Introduce the flow steering mlx5_flow_namespace (Namespace) and fs_prio (Flow Steering Priority) tree nodes. Namespaces are used in order to isolate different usages or types of steering (for example, downstream patches will add a different namespaces for the NIC driver and for E-Switch FDB usages). Flow Steering Priorities are objects that describes priorities ranges between different flow objects under the same namespace. Example, entries in priority i are matched before entries in priority i+1. This patch adds the following algorithms: 1) Calculate level: Each flow table has level(the priority between the flow tables). When we initialize the flow steering tree, we assign range of levels to each priority, therefore the level for new flow table is the location within the priority related to the range of the priority. 2) Match between match criteria. This function is used for searching flow group when new flow rule is added. 3) Match between match values. This function is used for searching flow table entry when new flow rule is added. 4) Add essential macros for traversing on a node's children. E.g. traversing on all the flow table of some priority Signed-off-by:
-
Maor Gottlieb authored
Introducing the base data structure and its operations that are going to represent ConnectX-4 Flow Steering, this data structure is basically a tree and all Flow steering objects such as (Flow Table/Flow Group/FTE/etc ..) are represented as fs_node(s). fs_node is the base object which describes a basic tree node, with the following extra info: type: describes the runtime type of the node (Object). lock: lock this node sub-tree. ref_count: number of children + current references. remove_func: a generic destructor. fs_node types will be used and explained once the usage is added in the following patches. Signed-off-by:
-
